rivera primo transmission dip stick

You search Auto repair manual PDF rivera primo transmission dip stick, if there are search results will appear below. If search results do not exist, please search by others keyword.



  rivera primo transmission dip stick Direct Download speed 5282 Kb/s

  rivera primo transmission dip stick Full Version speed 6162 Kb/s



HARLEY DAVIDSON ENGINE/ TRANSMISSION INTERFACE AND TOP COVER INSTALLATION

0

Filed Under (Harley Davidson) by admin on 25-12-2010

download
1. Refer to the Owner’s Manual and follow the instructions given to remove the maxi-fuse. 3 1 2 is02998 1. Transmission top cover screw (4) 2. Oil spout assembly screw 3. Upper bearing housing screw (2) Figure 1. Interface Cover Installation 2. See Figure 1. Remove and retain the four socket head cap screws (1) that fasten the front and right side of the transmission cover. See Figure 3. Obtain the chrome top interface cover (3) from the kit. NOTE The top interface cover can be carefully brought into position on top of the transmission housing from either the right or left side without removing or loosening any vehicle components. 3. Position the top interface cover over the transmission top cover. Loosely fasten the chrome cover to the top of the transmission housing with the screws removed in Step 2. 4. Obtain the chrome filler neck cover (4), 1/4-20 socket head screw (5), flat washer (6) and spacer (7) from the kit. Remove the oil level dipstick from the oil spout on the side of the transmission housing, wipe off and set it aside for later installation. NOTE Insert a clean shop rag into the oil spout opening while the dipstick is not installed. With the dipstick removed, small parts or other foreign material could fall into the transmission, leading to equipment damage or malfunction. 5. See Figure 1. Remove and discard the socket head cap screw (2) that fastens the oil spout assembly to the transmission housing. DO NOT remove the oil spout from the vehicle. 6. Place the flat washer over the threads of the new screw, and insert the screw into the unthreaded hole in the chrome filler neck cover. Place the spacer onto the screw threads. Apply a few drops of Loctite® 243 (Blue) to the screw threads, and position the chrome cover onto the oil spout on the transmission housing. Lubricate the filler neck gasket with soapy water to aid in installation. Tighten the screw to 84-132 in-lbs (9.5-15 Nm) . 7. See Figure 3. Obtain the chrome lower side interface cover (1), one #10-24 socket head screw (8) and one chrome flat washer (9) from the kit. NOTE For models with mid controls, the right-side rider footrest (foot peg) support bracket must be loosened to allow installation of the lower side interface cover. After the cover has been installed, tighten the footrest bracket attaching screws to 25- 35 ft-lbs (34-47 Nm) . 8. Position the cover around the chrome filler neck cover installed in Step 6. Loosely fasten the cover to the threaded hole in the filler neck cover with the screw and washer. 9. Obtain the chrome upper side interface cover (2), three #10-24 socket head screws (8) and three chrome flat washers (9) from the kit

Incoming search terms:

HARLEY DAVIDSON ENGINE/ TRANSMISSION INTERFACE AND TOP COVER INSTALLATION INSRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. Refer to the Owner’s Manual and follow the instructions given to remove the maxi-fuse. 3 1 2 is02998 1. Transmission top cover screw (4) 2. Oil spout assembly screw 3. Upper bearing housing screw (2) Figure 1. Interface Cover Installation 2. See Figure 1. Remove and retain the four socket head cap screws (1) that fasten the front and right side of the transmission cover. See Figure 3. Obtain the chrome top interface cover (3) from the kit. NOTE The top interface cover can be carefully brought into position on top of the transmission housing from either the right or left side without removing or loosening any vehicle components. 3. Position the top interface cover over the transmission top cover. Loosely fasten the chrome cover to the top of the transmission housing with the screws removed in Step 2. 4. Obtain the chrome filler neck cover (4), 1/4-20 socket head screw (5), flat washer (6) and spacer (7) from the kit. Remove the oil level dipstick from the oil spout on the side of the transmission housing, wipe off and set it aside for later installation. NOTE Insert a clean shop rag into the oil spout opening while the dipstick is not installed. With the dipstick removed, small parts or other foreign material could fall into the transmission, leading to equipment damage or malfunction. 5. See Figure 1. Remove and discard the socket head cap screw (2) that fastens the oil spout assembly to the transmission housing. DO NOT remove the oil spout from the vehicle. 6. Place the flat washer over the threads of the new screw, and insert the screw into the unthreaded hole in the chrome filler neck cover. Place the spacer onto the screw threads. Apply a few drops of Loctite® 243 (Blue) to the screw threads, and position the chrome cover onto the oil spout on the transmission housing. Lubricate the filler neck gasket with soapy water to aid in installation. Tighten the screw to 84-132 in-lbs (9.5-15 Nm) . 7. See Figure 3. Obtain the chrome lower side interface cover (1), one #10-24 socket head screw (8) and one chrome flat washer (9) from the kit

Incoming search terms:

HARLEY DAVIDSON CHROME TRANSMISSION HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-03-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect battery cable, negative (-) cable only. NOTE The starter does not need to be removed to install this kit. 2. Remove exhaust system only if needed to access transmission top cover hardware. Refer to Service Manual for instructions. NOTES Replace existing zinc hardware with chrome-plated hardware one at a time so the transmission top and side covers do not need to be replaced. 3. Remove and discard existing six 1/4-20 x 1 in. hex socket- head screws and washers from top transmission cover. Install six chrome hex socket head screws (1) and washers (2) on top transmission cover (3). Tighten to 84-108 in-lbs (9.5-12.2 Nm). 4. Remove and discard existing two 1/4-20 x 1 in. hex socket head screws and washers from side transmission cover. Install two chrome hex socket head screws (1) and washers (2) on side transmission cover (5). Tighten to 84- 108 in-lbs (9.5-12.2 Nm). 5. Remove and discard existing four 1/4-20 x 1-1/2 in. hex socket head screws and washers from side transmission cover. Install four chrome hex socket head screws (4) and washers (2) on transmission side cover (5). Tighten to 84- 108 in-lbs (9.5-12.2 Nm). 6. Install exhaust system if previously removed. Refer to Service Manual for instructions. 7. Connect negative (-) battery cable

HARLEY DAVIDSON ENGINE/TRANSMISSION INTERFACE AND TOP COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-04-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. Refer to the Owner’s Manual and follow the instructions given to remove the maxi-fuse. 1 4 3 2 is03621 1. Transmission top cover screw (3) 2. Upper and lower rear bearing housing screw (2) 3. Upper front bearing housing screw 4. Lower front bearing housing screw Figure 1. Interface Cover Installation 2. See Figure 1. Remove the two rear bearing housing screws (2) from the side of the transmission case. 3. Remove the oil level dipstick from the oil spout on the side of the transmission housing, wipe off and set it aside for later installation. NOTE Insert a clean shop rag into the oil spout opening while the dipstick is not installed. With the dipstick removed, small parts or other foreign material could fall into the transmission, leading to equipment damage or malfunction. 4. See Figure 2. Obtain the rear interface mounting bracket (1) from the kit. 5. Apply a few drops of Loctite 243 (Blue) to the threads of the two bearing housing screws removed in Step 2. Install the rear interface mounting bracket to the bearing housing with the screws, and tighten to 13-18 ft-lbs (17.6-24.4 Nm) . 6. See Figure 1. Remove the upper front bearing housing screw (3) from the side of the transmission case. Loosen the lower front bearing housing screw (4). 7. See Figure 2. Obtain the front interface mounting bracket (2) from the kit. 8. Apply a few drops of Loctite 243 (Blue) to the threads of the upper front bearing housing screw removed in Step 6. Hook the slot in the front interface mounting bracket under the loosened lower screw head. Install the bracket to the bearing housing with the upper screw, and tighten both screws to 13-18 ft-lbs (17.6-24.4 Nm) . 9. See Figure 1. Remove and retain the three socket head cap screws (1) that fasten the right side and left front corner of the transmission cover. 10. Remove and retain the screw fastening the rear brake line P-clamp to the rear fork bracket. 11. See Figure 2. Obtain the right rear interface cover (3), two chrome 1/4-20 screws (6) and two flat washers (7) from the kit. 12. From the rear of the motorcycle, bring the right rear interface cover into position behind the rear exhaust pipe, over the bearing housing. The hole in the top surface of the cover should be positioned over the right rear transmission top cover hole. 13. Loosely fasten the interface cover to the rear interface mounting bracket with the two chrome screws and flat washers. 14. Obtain the chrome top interface cover (4) from the kit. 15. Position the top interface cover over the transmission top cover, overlapping the tab at the top front of the chrome right rear interface cover

Harley-Davidson Motorcycle Reverse Gear Installation Instructions

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
2.1 Obtain a small tube of Loctite® #262 (red) for use later. 2.2 Drain the transmission oil. 2.3 Remove the clutch adjustment cover (left side). 2.4 Remove rear exhaust header pipe (cross over exhaust pipe). 2.5 Remove the muffler support bracket. 2.6 Remove the clutch release cover (right side). 2.7 Remove clutch push rod and oil slinger. To be disassembled and modified later. 2.8 Remove the two nuts from the main (rear) and counter (front) transmission shafts. 2.9 Remove the transmission bearing housing (puller available from Champion Sidecars). To be replaced with new reverse gear transmission bearing housing (Trap Door). 2.10 Cover the exposed gears in the transmission with a cloth in preparation to cut the shifter fork shaft. 3 Install New Main and Countershaft Gears NOTE: Gears and Tapered Split Rings are factory matched sets. Do not mix!. 3.1 Locate the shifter fork rod, mark fork rod flush at transmission case and pull out 1/4″. Figure 1 Figure 2. Exposed Shoulders Mark shifter fork rod flush with case Remove Spacers Vehicle Transmission Counter Shaft Main Shaft Front of Motorcycle Figure 1
Reverse Gear Installation Instructions For EVO / 5 Speed and Twin Cam Harley-Davidson® Motorcycle Page 3 of 6 Revision 7 © 2007 Champion Motorcycle Accessories International, Inc. dba Champion Sidecars 11841 Monarch Street Garden Grove, CA 92841 (800) 875-0949 (714) 847-0949 www.championsidecars.com www.championtrikes.com Figure 6 CAUTION: Do not pull the shifter fork rod out of the transmission more than 1/4″. If you pull the shifter fork rod out too far, it will be difficult to realign it with the internal shifter fork. 3.2 Cut the shaft at the mark and push it back in. The shaft end MUST NOT stick out of the transmission case. If the shaft is in deeper, fill the hole with silicone to prevent the shaft from moving in and out. NOTE: Shifter fork is made of non-tempered metal and may be cut with a hacksaw or Dremel® cutting tool. 3.3 Important: Remove stock spacers from main and counter shafts. Spray with silicon remover (Brake-Clean) then, using supplied cleaning pad, clean shafts, new counter and main shaft gears and tapered lock rings (inside and outside) Figure 1 3.4 With motorcycle in neutral, pull both the shafts out and simultaneously push the OEM outermost gears in until seated completely to expose the shoulders of both shafts. The countershaft shoulder should be flush with the gear face. For the main shaft the gear would “hang over” the shoulder a small bit. Figure 2 3.5 Apply supplied Champion Super-Lock retaining compound to the inside and outside surfaces of the large gear tapered split ring, to the inside of the new countershaft gear (large gear) and to the transmission countershaft (the forward most shaft). 3.6 Install new countershaft gear to the transmission countershaft. Insert tapered split ring (tapered end first) into the countershaft gear. Install ring seat tool and spring to counter shaft and new countershaft gear. Torque ring seat tool to 40 ft-lb’s. Figures 3 and 4

Incoming search terms:

A750 Transmission Solenoid Identification Automatic Transmission/ Transaxle

0

Filed Under (Toyota Manuals) by admin on 19-09-2011

Download
Provided below isachartlisting the Repair Manual name of each solenoid used in the A750 transmission, as well as the part name description provided in the electronic parts catalog. REPAIR MANUAL SOLENOID NAME PARTS CATALOGP ART DESCRIPTION S1 3WayTransmission Solenoid S2 Transmission Solenoid#3 SL1 Clutch Control Solenoid#1 SL2 Clutch Control Solenoid#2 SLT Line Pressure Control Solenoid SLU Lock UpControl Solenoid SR

Incoming search terms:

HARLEY-DAVIDSON 5 Speed Transmissions 1984 – 1999 EVO / 5 Speed & 1999 – 2006 Twin Cam Installation Instructions

0

Filed Under (Harley Davidson) by admin on 26-11-2010

download
Remove Original Parts From Vehicle. 2.1 Obtain a small tube of Loctite® #262 (red) for use later. 2.2 Drain the transmission oil. 2.3 Remove the clutch adjustment cover (left side). 2.4 Remove rear exhaust header pipe (cross over exhaust pipe). 2.5 Remove the muffler support bracket. 2.6 Remove the clutch release cover (right side). 2.7 Remove clutch push rod and oil slinger. To be disassembled and modified later. 2.8 Remove the two nuts from the main (rear) and counter (front) transmission shafts. 2.9 Remove the transmission bearing housing (puller available from Champion Sidecars). To be replaced with new reverse gear transmission bearing housing (Trap Door). 2.10 Cover the exposed gears in the transmission with a cloth in preparation to cut the shifter fork shaft. 3 Install New Main and Countershaft Gears NOTE: Gears and Tapered Split Rings are factory matched sets. Do not mix!. 3.1 Locate the shifter fork rod, mark fork rod flush at transmission case and pull out 1/4″. Figure 1 3.2 Cut the shaft at the mark and push it back in. The shaft end MUST NOT stick out of the transmission case. If the shaft is in deeper, fill the hole with silicone to prevent the shaft from moving in and out. NOTE: Shifter fork is made of non-tempered metal and may be cut with a hacksaw or Dremel® cutting tool. 3.3 Important: Remove stock spacers from main and counter shafts. Spray with silicon remover (Brake-Clean) then, using supplied cleaning pad, clean shafts, new counter and main shaft gears and tapered lock rings (inside and outside) Figure 1 3.4 With motorcycle in neutral, pull both the shafts out and simultaneously push the OEM outermost gears in until seated completely to expose the shoulders of both shafts. The countershaft shoulder should be flush with the gear face. For the main shaft the gear would “hang over” the shoulder a small bit. Figure 2 3.5 Apply supplied Champion Super-Lock retaining compound to the inside and outside surfaces of the large gear tapered split ring, to the inside of the new countershaft gear (large gear) and to the transmission countershaft (the forward most shaft). 3.6 Install new countershaft gear to the transmission countershaft. Insert tapered split ring (tapered end first) into the countershaft gear. Install ring seat tool and spring to counter shaft and new countershaft gear. Torque ring seat tool to 40 ft-lb’s. Figures 3 and 4

Incoming search terms:

HARLEY DAVIDSON SOFTAIL TRANSMISSION TOP-COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION – TOP COVER 1. See Figure 3. Remove and retain the stock screw (J) from the top of the transmission upper cover (I). 2. Ease the left side of the cover through the right side of the engine. You may need to angle the transmission cover slightly as you work it into position. 3. Fasten the weld-nut end of the top-cover bracket (2) to the top cover (4) using the screw (3) from the kit. Torque the screw to 6.6 – 9 ft-lbs (8.9 – 12.2 Nm). 4. Fasten the top of the top-cover bracket (2) to the left side of the transmission upper cover using the screw (J) removed in step 1. Torque the screw to 8 – 10 ft-lbs (10.8 – 13.5 Nm). 5. Install the Softail transmission-interface cover (D). Go to the next section in this instruction sheet. NOTE Save the washer (1) from this kit for transmission-interface cover installation. INSTALLATION – INTERFACE COVER 1. See Figure 1. Remove the screw (1) from interface cover at location 1. Keep the screw for installation. 2. Loosen the screw (2) at location 2 approximately three turns. 3. See Figure 2. Position the slotted hole (1) on the interface- cover mounting bracket (2) behind the washer at location 2. 4. Install the screw (4) from Step 1 through the mounting hole on the bracket and into location 1. Tighten the screw to 7 – 9 ft-lbs (9.5 – 12 Nm). 5. Tighten the screw (3) in location 2 to 13-16 ft-lbs (17.6 – 21.7 Nm). 6. See Figure 3. Place the interface cover (D) in position on the motorcycle. Spread the oil-line grommet (E) to wrap around the oil lines, then re-position the grommet in the interface cover. The edge of the interface cover must overlap the top of the top cover

Incoming search terms:

New Automatic Transmission for Motorcycles Human-Friendly Transmission

0

Filed Under (Honda) by admin on 18-12-2011

download
High-pressure fluid flow The engine rotates the pump swash plate, which has a gear mechanism. The rotating swash plate pushes the pump pistons to increase the pressure on the hydraulic fluid and feed it to the high-pressure annular chamber. The high- pressure fluid is then fed to the oil motor piston chamber where it pushes the pistons forward, which then push the motor swash plate. Power Fluid flow from pump to motor Fluid flow from motor to pump Low-pressure fluid flow The lower-pressure hydraulic fluid returns to the pump through the low-pressure annular chamber. In this way, the fluid circulates between the pump and the motor. Movement of distributor valves and pistons The distributor valves play an important role in fluid circulation. The valves are placed both in the oil pump and motor. When the pump pistons move to the compression side, the valves connect the piston chamber and the high- pressure chamber. When the pump pistons move to the expansion side, the valves allow a connection between the piston chamber and the low-pressure chamber. The valve in the oil motor moves opposite to its counterpart in the pump, ensuring the circulation of fluid within the system

Automatic Transmission/ Transaxle Fluid Level Inspection Temperature Rang es

0

Filed Under (Toyota Manuals) by admin on 12-10-2011

download
For vehicles equipped witha transmission requiring the use of the overflow type automatic transmission fluid (ATF) inspection process, the A TF must be withinaspecific temperature range for accurate fluid level inspection. Inspecting the A TF outside of the specified temperature range may result in incorrectA TF fluid levels and could lead to shift quality, M.I.L. “ON”, and/or transmission damage issues. Please seethe information in this bulletin for updated A TF level inspection temperature ranges. HINT For additional information including animations and video illustrations, please seethe Technical Training course E076: “Toyota ATF Level Inspection”. NOTE Please see TSB No. TC 010-07, “World Standard Automatic Transmission Fluid”, for important tips when working with A TFWS. ©2008 ToyotaMotor Sales, USA Page 1of3
T-SB-0129-08 July9,2008 Page 2of3 Automatic Transmission/Transaxle Fluid Level Inspection Temperature Ranges Warranty Information OP CODE DESCRIPTION TIME OFP T1 T2 N/A Not Applicable to Warranty – - — Parts Information PREVIOUS PART NUMBER CURRENT PART NUMBER PART NAME QTY 00289-ATFWS Same ATFWS As needed Required Tools&Equipment

Incoming search terms:

Incoming search terms: