rubber boot seal around shifter 2012 goldwing

You search Auto repair manual PDF rubber boot seal around shifter 2012 goldwing, if there are search results will appear below. If search results do not exist, please search by others keyword.



  rubber boot seal around shifter 2012 goldwing Direct Download speed 5282 Kb/s

  rubber boot seal around shifter 2012 goldwing Full Version speed 6162 Kb/s



TRIUMPH ROCKET III HEEL / TOE SHIFTER INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Loosen the 10mm nuts at the ends of the shifter linkage rod (notice one end is a left hand thread). Remove the 10mm nut from the shifter arm & disengage the linkage. Remove the shifter pivot bolt using a 8mm hex key wrench. Remove the washer on the threaded side of the shifter pivot bolt. 2. Place one of the wave washers supplied onto the pivot bolt. Place a small amount of grease on the shifter pivot bolt shank and the Heel / Toe shifter pivot hole, insert the pivot bolt into the pivot hole of the toe heel shifter. Use a drop of blue loctite on the shifter pivot bolt threads and install the Heel / Toe shifter, tighten the pivot bolt securely. Check to see that the shifter pivots freely. If the side play is excessive (this is a result of variances in manufacturing tolerances of the stock and supplied components) remove the pivot bolt and install the second wave washer supplied. 3. Unscrew the linkage rod and replace it with the longer rod supplied (NOTE the rod has a left hand thread on one end and right hand threads on the other). Insert the shifter linkage stud into the desired hole in the new shifter being sure the flats on the stud engage the slot on the backside of the bolthole. Install the nut and finger-tighten only at this time. 4. While seated on the motorcycle first find the height setting you prefer for the toe shifter. Using one of the three boltholes for the linkage can set this. You can also gain some adjustment by exposing more or less threads of the new longer shifter linkage rod; however be sue that you have a minimum of 4-5 threads still engaged in the linkage ends. After setting the height, tighten all three 10mm nuts (the two at the ends of the linkage rod and the one which attaches the linkage to the toe/heel shifter) securely. After you have the toe shifter adjusted to your liking you can select the heel shifter height by moving the button head cap screw that secures the toe shifter to the heel shifter (Using a 5/32″ hex key wrench) next to the 10mm linkage nut to any of its three holes

Incoming search terms:

HARLEY DAVIDSON ALUMINUM SHIFTER LINKAGE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
REMOVAL 1. See Figure 1. Remove stock shifter rod (D). 2. Adjust new shifter rod in kit to match the length of the removed shifter rod by loosening locknuts (3), adjusting the length of the rod, then tightening locknuts to 20-24 ft- lbs (27-32 Nm) . 3. For models with a straight rear shifter rod lever: Discard spacer (7). Place cover (1) over the shifter rod lever (C). For models with an offset rear shifter rod lever: Place spacer (7) and cover (1) over the shifter rod lever (C). INSTALLATION 1. Apply Loctite® 243 to threads of capscrew (5) and install cap screw through the rear of the shifter rod and into the shifter rod lever. Tighten cap screw to 13-16 ft-lbs (18-22 Nm) . 2. For 1999 and later FLHT, FLHX, FLHR, and FXDWG models: Place the rod end on the outside of the shifter lever, then apply Loctite® 243 to the threads of capscrew (5). Attach the front of the shifter rod (6) to the shifter lever with capscrew (5) and acorn nut (4) (with acorn nut facing out). Tighten acorn nut (4) to 13-16 ft-lbs (18-22 Nm) . For all models except 1999 and later FLHT, FLHX, FLHR, and FXDWG: Place the rod end on the inside of the shifter lever then apply Loctite® 243 to the threads of cap screw (5). Attach the front of the shifter rod (6) to the shifter lever with cap screw and acorn nut (4). Tighten acorn nut (4) to 13-16 ft-lbs (18-22 Nm)

Incoming search terms:

HARLEY DAVIDSON DYNA FLOORBOARD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-03-2011

download
Installation SHIFTER ASSEMBLY (LEFT SIDE) 1. Remove highway footrest assembly, if equipped. Discard bracket, plate and mounting hardware. 2. Remove stock footrest assembly. 3. Remove stock (chrome) shift lever. Retain shift lever, peg, bolt and washer. 1 WARNING ® 1 of 5 Kit Number 50601-01 -J01921 2 of 5 Figure 1. Shifter Assembly (Left Side) Item Description Part No. 1 Bolt, 5/16-18 x 5/8 hex HD 2882W 2 Hex cap screw, 5/16-18 x 2.00 (2) 3023 4 Set screw, shaft cover 3231B 6 Assembly,shift lever 33704-01A 7 Assembly,adjustable shifter rod 33719-79B 8 Lever, shifter, machining, polish 33706-01 9 Assembly, shifter plate, polish 33700-01 10 Cover, shifter lever, rubber (2) 34619-85 11 Retainer,shift lever for 1996 to 2000 models 34639-93 Item Description Part No. 11ARetainer bracket, shift lever for 2001 and later models 34639-01 12 Cover, shifter shaft 34640-93 13 Washer, wave, overlap type (2) 34641-01 17 Socket head cap screw 4740A 25 Washer, 5/16″ (2) 6016 28 Washer. 5/16″ 6702 30 Nut, hex, locking, 5/16-18 7710W 32 Acorn nut, 5/16-24 7736 33 Hex jam nut, 5/16-24 7744 30 11 1 12 7 32 28 6 13 9 25 2 17 25 2 10 8 i03110.eps 33 4 11A ’96-2000 models 2001 and later models 4. See Figure 1. 1996 to 2000 models. Bolt shifter lever shaft retainer bracket (11) to the stock shifter lever with bolt (1) and nut (30). Do not tighten bolt at this time. 2001 and later models. Bolt shifter lever shaft retainer bracket (11A) to the stock shifter lever with bolt (1) and nut (30). Do not tighten bolt at this time. 5. Loosen the left rear crankcase bolt (at bottom of cylinder) and slide the slotted end of shifter lever shaft retainer bracket (11) onto the bolt, but beneath the washer. Tighten crankcase stud to 15-17 ft-lbs (20-23 Nm). 6. Place chrome cover (12) on shifter lever shaft (at primary case) and secure with set screw (5). NOTE Small wave washer (13) goes between foot shifter and bracket. 7. See Figure 1. Place small wave washer (13) on shifter lever (6) shaft. Coat shaft with Loctite Anti-seize and slide into bracket. 8. Install foot shift bracket (9) using screws (2). Tighten screws to 25-30 ft-lbs (34-41 Nm). 9. Place shifter rod (2) and washers (25) in position. Use short stud on shifter rod to secure shifter rod at the transmission end. Use Loctite 242 (blue) on stud before installing. 10. Install acorn nut (32) and washer (28) at foot shift end. Use Loctite 242 (blue) on acorn nut before installing

HARLEY DAVIDSON SHIFTER SHAFT COVER WITH INSERT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION 1 2 4 3 5 6 7 is01872 1. Shifter shaft 2. Inner cover 3. Toe shifter lever 4. Outer cover 5. Set screw (for outer cover) 6. Set screw (for inner cover) 7. Casting Figure 1. Shifter Shaft Covers 1. See Figure 1. Remove the stock heel shift lever and toe shift lever (3) from the gear shifter shaft (1). 2. Install the set screw (6) into the inner gear shifter shaft cover (2). 3. Install inner gear shifter shaft cover with installed set screw over the casting (7) in-board of the shifter shaft (1). 4. Tighten the set screw until light contact is made with the casting. Do not overtighten. 5. Re-install toe shift lever on the gear shifter shaft. Tighten the shifter retaining screw to 18-22 lb-ft (24-30 Nm) . 6. Install the set screw (5) into the outer gear shifter cover (4). 7. Install outer gear shifter shaft cover with installed set screw over the end of the gear shifter shaft (1). 8. Loosen the set screw slightly to allow the gear shifter shaft cover to rotate. Rotate the cover until the set screw faces down, then tighten the set screw. SERVICE PARTS

Incoming search terms:

harley- davidson DYNA BLACK FORWARD CONTROL KIT installation Manual

0

Filed Under (Harley Davidson) by admin on 15-03-2012

download
1. Disconnect battery cable, negative (-) cable first. 2. Remove the left side rider footrest assembly. Save the footrest and fasteners for installation. Discard the remaining hardware. 3. From the kit, press hole plugs (8) into the screw holes on the frame where the stock footrest assembly was mounted. 4. Remove plugs from forward control frame mount (I) and discard. 5. Remove the foot shifter lever (A) and shifter peg (D). Discard the old foot shifter lever (A). Save the foot shifter lever hardware and shifter peg (D) for future use. 6. See Figure 2. Remove the primary chaincase cover (6) and primary chaincase housing (1). Refer to your model motorcycles Service Manual for removal procedures. NOTE See Figure 1. Before removing the gear shifter lever (1) ((H) in Table 1), it is necessary to mark the correct orientation of the lever. Using a marking tool, draw a location marking (4) on the end of the splined shaft (2) across from the casting split (3). This will allow the new gear shifter lever to be installed in the same orientation as the old lever. 5 3 4 1 2 is 02083 1. Gear shifter lever 2. Splined shaft 3. Casting split 4. Location marking 5. Lever bolt Figure 1. Gear Shifter Lever Orientation 7. After marking the gear shifter lever orientation, loosen the lever bolt (5) and remove the old shifter lever. Discard the old gear shifter lever but keep the lever bolt. From the kit, install the new gear shifter lever onto the splined shaft in the same orientation as the old shifter lever. Tighten the lever bolt to 18-22 ft-lbs (24.4-29.8 Nm)

HARLEY DAVIDSON BILLET SHIFTER PEG INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-04-2011

download
Kit Contents See Figure 1 and Table 1. INSTALLATION 1. Remove and discard the original equipment shifter peg. If needed, use a heat gun to apply heat to the shift lever and shifter peg threads to aid in peg removal. 2. See Figure 1. Insert the screw through the peg into the shift lever. Tighten the screw to 11-15 ft-lbs (15-20 Nm) . -J04379 1 of 2 SERVICE PARTS 1 2 B C 1 2 3 1 2 3 A is05070 Figure 1. Service Parts: Billet Shifter Peg Kits Table 1. Service Parts Table Part Number Description (Quantity) Item A – Kit 49256-99 3396 Screw, 5/16-24 x 2.25 socket head cap, lockpatch 1 Not Sold Separately Shifter peg 2 11306 Rubber (4) 3 B – Kit 49254-99 3396 Screw, 5/16-24 x 2.25 socket head cap, lockpatch 1 Not Sold Separately Shifter peg 2 11306 Rubber (4) 3 C – Kit 49238-98 3396 Screw, 5/16-24 x 2.25 socket head cap, lockpatch 1 Not Sold Separately Shifter peg 2

AJS DISMANTLING AND REBUILDING FULL-WIDTH FRONT WHEEL HUBS INSTALLATION

0

Filed Under (AJS) by admin on 31-10-2010

download
Removal of the Brake-side Bearing Cup The bearing cup (5) is located endwise by a circlip (1), and between the cup and circlip arc an oil-seal retaining washer (4), oil seal (3), and oil-seal cup washer (2) Before these parts can be removed from the hub the bearing cup must be moved inwards for a very short distance (3/16-inch) so that the circlip can be withdrawn. (n) Gently heat the hub shell. (i) Place a soft metal rod (e.g. brass) against the oil-seal cup washer (2) and apply pressure with a hand press or hammer blows. It is only necessary to move the bearing cup (5) inwards about 1/16-inch. (j) Extract the circlip by inserting a narrow pen-knife blade under one end of the circlip; lift it upwards and outwards and prise the clip out of its groove. (k) Remove the oil-seal cup washer (2), oil seal (3) and oil-seal retaining washer (4). They can be hooked out with the shank of a small and narrow screw­ driver, (l) The bearing cup can now be ejected by placing a suitable rod of soft metal (e.g. brass) in the hub tunnel from the right-hand side and pressing it — with a press or hammer blows — against the bearing cup until the cup is forced out of the bearing. This must be done with care so that the cup remains square with the housing. Reassembly To facilitate replacement of the bearing cups gently heat the hub shell. Just too hot to hold is about the right temperature. (a) Place the brake-side bearing cup squarely in the hub shell — the open end faces inwards — and press it into the hub tunnel A short length of brass rod, slightly less than the outside dia­ meter of the cup, should be interposed between the cup and ram of the press, or hammer head. Press the cup in until the outer face is approximately half-an-inch below the mouth of the hub tunnel. This will allow sufficient room to allow [he circlip to be inserted into its groove. (b) Refit in the following order: oil-seal retaining washer (4), oil seal (3), oil-seal cup washer (2). (c) The circlip can now be replaced. In the interest of reliability use a new circlip, for it is possible that the existing circlip was strained when it was re­ moved. (d) Insert into the hub tunnel from the right-hand side a brass rod of suitable length, and press the bearing cup firmly against the circlip. (e) Before inserting the spindle complete with the roller races, pack them with clean and fresh grease of a suitable grade (Mobilgrease No. 4. Castrolease heavy, Energrease C3, Esso Pressure Gun Grease. Shelf Retinax Grease CD or A). (0 Insert the spindle into the hub. (g) Place the right-hand side bearing cup in the hub tunnel; the open end faces inwards, It may be necessary to re-heat the hub to allow the cup to go into position without difficulty. (h) Press the cup into position, but do not force it fully home, leave some end play on the spindle. (i) Refit in the following order: oil-seal retaining washer (6), oil-seal (7) and oil-seal cup washer (8). (j) Screw into the hub the adjusting sleeve (9) until it comes into contact with the bearing cup (5)

RACE TECH SUSPENSION SERVICE TOOLS

0

Filed Under (Tips and Review) by admin on 01-12-2010

download
SHOCK SEAL BULLET TOOL “Bullet Tools” make seal head installation onto shafts quick and easy. 35-8677 TSSB12512.5 x 10mm Shock Seal Bullet 35-8678 TSSB1414 x 12mm Shock Seal Bullet 35-8679 TSSB1616 x 12mm Shock Seal Bullet FORK CAP WRENCH 46/50MM Black Oxidized steel construction for superior strength. Multiple applications (46/50mm): Honda CR250 (97-00), Suzuki RM125/250 (96-00), and removes compression adjuster assembly on Suzuki RM125/250 (98-00). Sold each. 35-8670 TFCW4650 Fork Cap Wrench SHAFT HOLDING TOOL Holds fork damping rods, cartridges, shock shafts, etc. while servicing. (aluminum) 35-8672 TFSH10 Shaft Holding Tool 10, 12, 12.5, & 14mm (Dampning Rods) 35-8673 TFSH14 Shaft Holding Tool 14, 16, & 18mm (Shock Shafts) 35-8674 TFSH20 Shaft Holding Tool 20, 24, & 29mm (20 & 25mm Fork Cartridges) 35-8675 TFSH32 Shaft Holding Tool 32 & 35mm (28 & 32mm Fork Cartridges) ULTRA SLICK SEAL GREASE Race Tech Ultra-Slick Grease provides maximum lubrication and minimum friction for all seal and bushing needs. Available in 1 oz. container. 35-8682 Ultra Slick Seal Grease SHOCK SEAL HEAD SETTING TOOL Allows easy removal and installation of all 40 – 46mm integral shock seal head assemblies. 35-8676 TFSH32 Shock Seal Head Setting Tool SAG MASTER™ The Sag Master is a tool that makes measuring “Race Sag”a snap because you read it directly. No more subtracting! Also useful in determining proper spring rates and monitoring linkage and seal drag. Comes with complete instructions and, doubles as a tape measure. 35-8681 TSSM01 Sag Master Race Sag Setting Tool FORK SPRING COMPRESSOR TOOL This unique fork spring compressor is designed to work on most current sport bikes and road racers. It allows the spring to be compressed while the fork cap is removed from the rod. It can be used on or off the bike on most models. 35-8680 TFSC01 Fork Spring Compressor Tool

Harley Davidson Twist Gear and Wide Gear Installation Instructions

0

Filed Under (Harley Davidson) by admin on 11-04-2012

download
Assemble triple lip output seal 705002 and output spacer 280001 together. The seal is shipped with high performance grease packed into the seal lips to ensure lubrication and exclude dust & water. (Caution: Only high temperature grease should be used, grease is better than oil, never install the seal dry.) Slide the quad ring and seal/spacer assembly onto the transmission output shaft, then slide tool JE300001 ( TwistGear TM ) or JE300002 ( WideGear ) onto the shaft and finally tighten the nut until the tool drives the seal flush with the case. Do not attempt to install the main drive seal without the JE tool or the seal will be damaged, and the seal performance will be compromised (the JE seal is wider around the shaft for the third sealing lip, which will be damaged if a tool is pressed against it.) It is best that a new JE spacer be used each time a new seal is installed for quick break-in of the main lip seal surface. Counter Shaft Assembly Note the order and orientation of the gears on the counter shaft when it is removed from the trapdoor. Disassemble the counter shaft and transfer the parts to the TwistGear TM counter shaft. Note that the TwistGear TM counter shaft assembles in different order than the OEM counter shaft. Two washers are required in the position as shown in figure 1 (see arrow) before the retainer ring is installed. The second washer is included in the kit.

Incoming search terms:

TOYOTA TACOMA TRANSMISSION TO ATLAS TRANSFER CASE

0

Filed Under (Toyota Manuals) by admin on 20-09-2011

Download
Remove the stock transfer case from the stock tailhousing adapter. The stock tailhousing is retained along with the stock rubber crossmember support. Once the transfer case is removed, you’ll see a seal located in the stock tailhousing. This seal must be removed and discarded. Some tailhousings also had a bearing which also must be removed. Install the new oil seal into the large end of the seal adapter. The sealing lip should be facing down. The small end of the seal adapter has the same O.D. (outside diameter) as the old seal that was just removed from the stock tailhousing. The seal adapter is a press-fit into the stock tail and should now be installed. The kit comes with a new spud shaft which fits over the stock Toyota transmission 26 spline output shaft. This spud shaft has a Jeep 23 male spline on the opposite side which fits into a standard 23 spline Atlas case. When installing the spud shaft into the Toyota transmission, the spud shaft does not seal onto the new seal just previously installed. The seal contacts seal off of the Atlas input shaft. The adapter plate should now be installed onto the Atlas transfer case. The adapter plate indexes off of the Atlas front retainer

Incoming search terms: