rusi ssy 150 cc electric start will not function

You search Auto repair manual PDF rusi ssy 150 cc electric start will not function, if there are search results will appear below. If search results do not exist, please search by others keyword.



  rusi ssy 150 cc electric start will not function Direct Download speed 5282 Kb/s

  rusi ssy 150 cc electric start will not function Full Version speed 6162 Kb/s



Pulsar XR 650R ELECTRIC-START KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Pulsar) by admin on 27-10-2010

download
1. Remove the seat, fuel tank, side panels, muffler, and headers. 2. Disconnect the stator wires from their corresponding mates underneath the seat (trace the wires up from the left side case.) Un-route the stator wiring so it hangs free from the left side case. 3. Remove the stock shift lever and the left side engine case cover. You do not need to drain the oil from the engine. 4. Unbolt and remove the stator and wiring from the stock cover. Do not cut any wires. 5. The stock pulsar coil (small black box hanging from the stator) will have to be modified slightly to clear the ring gear before installation into the new cover. Remove (file or grind) about .030 inches of material from the base of the pulsar coil so that the base is flush with the face of the rest of the coil as shown in Photos 1 and 2. File Here Photo 2 Make flush with this surface Remove material here Photo 1 6. Install the stator and modified pulsar coil into the new engine case cover as shown in Photo 3. Use the three provided Phillips head bolts, split lock-washers, and plastic cable clamps to secure the wiring as shown. You will need to pull about ½” of extra wire through the grommet (Photo 4) to give you enough wire length for the grommet to sit in its case cutout. To do this, remove the electrical tape from the end of the stator wires and pull each wire individually through the grommet. Neither of the stock metal wire guides will be used when reinstalling the stator into the new case (Photo 5). 5/16″ cable clamps 1/8″ cable clamp Photo 3 Photo 5 Not Used Pull extra wire through grommet Photo 4 7. Remove the stock flywheel nut (An air impact tool works best to remove this nut without turning the motor). Remove the flywheel using the flywheel puller provided. 8. Locate the T and F marks on the stock flywheel (Photo 6). The T mark is used to adjust valve clearances and its location needs to be transferred to the ring gear. Scribe a line in the edge of the flywheel in line with the T mark as shown in Photo 7

Yamaha WR motorcycle ProEFX 12V Hot Start Installation

0

Filed Under (Yamaha) by admin on 06-01-2012

download
1. Remove seat, tank and shrouds. Remove existing hot start lever, cable and valve from the carburetor. 2. Tip: Clean all dirt from hot start bore and mating surfaces on the carburetor body with gas and a q-tip. 3. Tip: Use a small amount of Teflon tape (one wrap) on the threads of the aluminum mounting nut to ensure a water tight seal. 4. Install the Pro EFX hot start valve in the hot start bore (as shown in picture), with return spring, impact washer and delrin plunger in place. • Tip: Installation of the solenoid valve may require temporary rotation of the carburetor away from the top engine mount bracket. • Install with the solenoid valve assembly disconnected from wiring harness. • Screw in by hand and finish tightening with needle nose pliers. Do not over-tighten. Solenoid valve assembly: 5. Mount activation switch on preferred handle bar location. Pictured on clutch side, in place of the stock kill switch.
6. Route wiring harness around steering column and down frame backbone. Insert battery leads through slot in rubber protective boot. (follow existing wiring to battery) 7. Connect positive (red) and negative (black) leads to motorcycle battery. 8. Connect male and female terminals to wiring harness on previously installed solenoid valve assembly. 9. Depress activation button and listen for valve actuation. Plunger should freely “snap” between open and closed position in hot start bore, as activation button is depressed and released. If you don’t hear the valve “snap” open and closed, follow the trouble shooting guidelines or call /email for support. 10. Maintenance: Periodically ensure proper tightness of solenoid valve in carburetor body as part of standard motorcycle maintenance. Keep the battery terminal connections free from corrosion.

Incoming search terms:

Motorcycle Alarm X60 Userʼs Manual

0

Filed Under (Tips and Review) by admin on 29-11-2010

download
REMOTE START Press the button twice within two seconds and hold, engine will start automatically, and used for keyless driving and warm-up. Repeat the above operation if the engine does not function due to cold weather or due to slow rotation of engine. NOTE: when using the remote start up, the switch key of the motorcycle cannot be pressed at the same time, otherwise the fuse will blow. How to turn off the remote start function: press the button once then engine will stop. ANTI HOTWIRE When system in armed mode if system detects the ignition is forcibly switched on (hotwired) siren will activate and indicator lights will remain solid, the engine is automatically immobilised and motorcycle cannot be started up. The siren will sound for 30 second if the ignition is switched off, otherwise it will sound continuously. ANTI HIJACK Press the button and button at the same time when ignition is on engine will immobilise immediately, siren will sound continuously and indicator lights will flash continuously. Press the button to de-activate anti hijack mode. VALET MODE In disarming mode, IGNITION OFF position, turn IGNITION ON/OFF 6 times and stopped at ON at the last time, then press button within 5 seconds. LED will be on constantly, indicating system entered into Valet Mode. In this mode, all alarming function disabled. Only remote engine start and bike finding function. Follow the same procedures to exit Valet Mode

2004 Honda CRF450R OWNER'S MANUAL

0

Filed Under (Honda) by admin on 21-11-2010

download
motorcycle can be kickstarted with the transmission in gear by disengaging the clutch before operating the kickstarter. Check the engine oil, transmission oil and coolant levels before starting the engine (page 21, 23, 24). Cold Engine Starting: 1. Turn the fuel valve ON. 2. Shift the transmission into neutral. 3. If the temperature is 35°C (95°F) or below, pull the choke knob fully out. 4. If the temperature is below 0°C (32°F), open the throttle two or three times. (The engine requires a richer mixture for starting in cold weather. When the throttle is so opened, the accelerator pump will feed extra fuel to the cylinder, thereby facilitating starting in cold weather.) 5. With the throttle closed, operate the kickstarter starting from the top of the kickstarter stroke, kick through to the bottom with a rapid, continuous motion. (Do not open the throttle, As the carburetor is equipped with an accelerator pump, excessive fuel will be charged into the engine, and the spark plug will be fouled if the throttle is opened and closed repeatedly. Excessive fuel in the engine makes kick- starting difficult.) 6. About a minute after the engine starts, push the choke knob back all the way to fully OFF. If idling is unstable, open the throttle slightly. (1) FUEL FILL CAP (2) BREATHER TUBE WARNING (1) FUEL VALVE (2) CHOKE KNOB Warm Engine Starting: 1. Turn the fuel valve ON. 2. Shift the transmission into neutral. 3. Pull the hot start lever and kick-start the engine. (Do not open the throttle.) 4. As soon as the engine starts, release the hot start lever 1. Shift the transmission into neutral. 2. Pull the hot start lever and kick-start the engine. (Do not open the throttle.) 3. As soon as the engine starts, release the hot start lever. Starting the engine excessively charged with fuel by throttle blipping or other reasons: 1. Shift the transmission into neutral. 2. With the throttle fully opened, repeat kickstarter operation approximately 10 times very slowly to discharge excessive fuel from the engine. 3. Pull the hot start lever and kick-start the engine (Do not open the throttle.) 4. As soon as the engine starts, release the hot start lever. Stopping The Engine 1. Shift the transmission into neutral. 2. Turn the fuel valve OFF. 3. Lightly open the throttle 2 – 3 times, and then close it. 4. Depress and hold the engine stop button until the engine stops completely. NOTE: • Failure to close the fuel valve may cause the carburetor to overflow. (1) THROTTLE GRIP (2) ENGINE STOP BUTTON Break-In Procedure Help assure your CRF’s future reliability and performance by paying extra attention to how you ride during the first operating day or 15 miles (25 km). During this period, avoid full-throttle starts and rapid acceleration. This same procedure should be followed each time when: • Piston is replaced • Rings are replaced • Cylinder is replaced • Crankshaft or crank bearing are replaced

Incoming search terms:

KTM 125 EXC, EXC SIXDAYS 200 XC, XC-W, EXC 250 XC, XC-W, EXC, EXCSIXDAYS 300 XC, XC-W, EXC-E, EXC-ESIXDAYS OWNER'S MANUAL 2008

0

Filed Under (KTM) by admin on 02-12-2010

download
Chassis number The chassis number is stamped on the right side of the steering head tube. Enter this number in the field on page no 1. Engine number, engine type The engine number and the engine type are stamped into the left side of the engine below the engine sprocket. Enter this number on page 1. Clutch lever The clutch lever [1] is located on the left side of the handlebars. The adjusting screw [A] is used to change the original position of the clutch lever (see maintenance work on chassis and engine). The clutch is hydraulically actuated and adjusts itself automatically. Hand brake lever The hand brake lever [2] is mounted on the handlebars on the right and actuates the front wheel brake. The adjusting screw [B] can be used to change the basic position of the hand brake lever (see maintenance work on chassis and engine). OPERATION INSTRUMENTS » 1 2 A B
ENGLISH 6 OPERATION INSTRUMENTS » TEST All of the display segments briefly light up for the display function test. WS (wheel size) The display changes and the circumference of the front wheel is briefly displayed in millimeters (2205 mm corresponds to a front wheel circumference of 21″ with production tires). Afterwards the display will return to the previous display mode. Electronic speedometer The display in the electronic speedometer is activated as soon as you press a button on the speedometer or an impulse is received from the wheel sensor. The display lights up when the engine is running. The display is cleared if no button is pressed for 1 minute or no impulse is received from the wheel sensor. The button is used to change between display modes. The + and – buttons are used to control various functions. SPEED display mode / H (service hours) Only the SPEED / H and SPEED / ODO display modes are activated in the condition at delivery. SPEED/H is displayed whenever the display is activated and the front wheel is not turning. It automatically changes to the SPEED/ODO display mode as soon as the front wheel starts turning. SPEED displays the speed. H displays the engine’s service hours. The service hour counter starts to count as soon as you start the engine. The displayed figure cannot be changed. Service intervals are indicated in service hours for some KTM offroad motorcycles, making the service hour counter a very practical function. SPEED / ODO display mode (odometer) The SPEED/ODO mode displays the speed and the total distance traveled. The display automatically changes to the SPEED/H display mode when the front wheel stops turning. + button no function – button no function briefly press buttonchanges to the next display mode hold button 3 secs. changes to the next display mode The electronic speedometer has a number of display modes (functions) that you can also activate (reveal) (see: Activating and deactivating display modes).
ENGLISH 7 OPERATION INSTRUMENTS » SPEED / LAP (lap time) display mode You can use the manual stop watch to stop and store up to 10 lap times, which you can view in the LAP/LAP display mode (see below). LAP displays the lap times in hours, minutes and seconds. + button Starts and stops the stop watch, lap time is not reset to 0 – button Stops the stop watch, stores the lap time and restarts the stop watch again. The time is reset to 0. A total of 10 lap times can be stored. If the lap time continues to run after you press the – button, all 10 memory locations are occupied.To clear all of the stored lap times, hold the button for 3 seconds in the SPEED/LAP mode.Up to 10 lap times can be stored in this way. briefly press buttonChanges to the next display mode.If no lap time is stored or the motorcycle is driving, the LAP/LAP mode will be skipped. hold button 3 secs. Clears all LAP figures SPEED / CLK (time) display mode CLK displays the time in hours, minutes and seconds. + button no function – button no function briefly press buttonchanges to the next display mode hold button 3 secs. set the clock menu To set the clock, see „Setting the clock”. Activating and deactivating display modes In the display mode SPEED/H, press and hold the button for 3 seconds to access the SETUP menu. The active functions will be displayed. The blinking function can be activated by pressing the + button and deactivated by pressing the – button. Press and hold the button 3 seconds to store the settings. If no button is pressed for 20 seconds, the setting will be stored automatically and the display will return to the SPEED/H mode. + button activates the blinking display – button deactivates the blinking display briefly press buttonchanges to the next display without changing any settings hold button 3 secs. starts the SETUP stores the settings and changes to the SPEED/H mode

Incoming search terms:

Vespa GTS Super Specification

0

Filed Under (Vespa) by admin on 11-11-2010

download
Gts super 300 ie Gts super 125 ie s 125cc s 50cc Gts 250 ie Gts 125cc LX 125cc LX 50cc 2 stroke Engine Single-cylinder, catalised, QUASAR 4 stroke, 4 valve electronic injection Single-cylinder LEADER 4 stroke with electronic injection Single-cylinder LEADER 4 stroke Single-cylinder HI-PER 2 stroke Single-cylinder, catalised, QUASAR 4 stroke, 4 valve electronic injection Single-cylinder, catalised, LEADER 4 stroke, 4 valve Single-cylinder LEADER 4 stroke Single-cylinder HI-PER 2 stroke Capacity 278cc 124cc 124cc 50cc 249cc 124cc 124cc 49cc Power 16.4 kW / 7500 rpm 10.5 Kw / 9500 rpm 7.65 Kw / 8250 rpm 3.2 Kw / 7500 rpm 15.7 Kw / 8500 rpm 7.65 Kw / 8250 rpm 7.65 Kw / 8250 rpm 2.5 Kw / 8500 rpm Max Torque 22Nm / 6500 rpm 12 Nm / 8000rpm 9.6 Nm / 7250 rpm 4.4 Nm / 6500 rpm 20.1 Nm / 6500 rpm 9.6 Nm / 7250 rpm 9.6 Nm / 7250 rpm 3.3 Nm / 6500 rpm Cooling Liquid Liquid Forced Air Forced Air Liquid Liquid Forced Air Forced Air Starter Electric Electric Electric and kick starter Electric and kick starter Electric Electric Electric and kick starter Electric and kick starter Transmission Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Front Suspension Single arm, dual chamber hydraulic shock absorber with coaxial spring Single arm link with coil spring and double hydraulic shock absorber Single arm link with coil spring and double hydraulic shock absorber Single arm link with coil spring and double hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Rear Suspension Two dual effect shock absorbers with adjustable preload Coil spring and double hydraulic shock absorber Coil spring and double hydraulic shock absorber Coil spring and double hydraulic shock absorber Twin hydraulic shock absorbers with preload adjuster Twin hydraulic shock absorbers with preload adjuster Hydraulic shock absorbers with preload adjuster Hydraulic shock absorber Front Brake ø 220mm disc brake 220mm disc brake ø 200mm disc brake ø 200mm disc brake ø 220mm disc brake ø 220mm disc brake ø 200mm disc brake ø 200mm disc brake Rear Brake ø 220mm disc brake 220mm disc brake ø 110mm drum brake ø 110mm drum brake ø 220mm disc brake ø 220mm disc brake ø 110mm drum brake ø 110mm drum brake Front Tyre Tubeless 120/70-12″ Tubeless 120/70 – 12″ Tubeless 110/70 – 11″ Tubeless 110/70 – 11″ Tubeless 120/70-12″ Tubeless 120/70-12″ Tubeless 110/70 – 11″ Tubeless 110/70-11″ Rear Tyre Tubeless 130/70-12″ Tubeless 130/70 – 12″ Tubeless 120/70 – 10″ Tubeless 120/70 – 10″ Tubeless 130/70-12″ Tubeless 130/70-12″ Tubeless 120/70 – 10″ Tubeless 120/70-10″ Running weight 158kg 158kg 114kg 96kg 151kg 145kg 114kg 96kg Length/Width/Height 2230mm / 755mm / 1170mm 1930mm / 755mm / 1930mm 1770mm / 740mm / 1140mm 1755mm / 740mm / 1140mm 1930mm / 755mm / 1170 mm 1940mm / 755mm / 1180 mm 1770mm / 740mm / 1140mm 1755mm / 740mm / 1140mm Fuel Tank Capacity 9 litres 9 litres 8.5 litres 8.5 litres 9.2 litres 10 litres 8.5 litres 8.5 litres Emmissions Euro 3 Euro 3 Euro 3 Euro 2 Euro 3 Euro 3 Euro 3 Euro 2 Colours Rosso Dragon Nero Lucido Montebianco Rosso Dragon Nero Lucido Montebianco Taormina Nero Lucido Montebianco Taormina Nero Lucido Montebianco Marrone Terra Di Toscana Bronzo Perseo Nero Vulcano Blu Midnight

Incoming search terms:

Dazon Raider Classic 150 (Oil-cooled & Internal Gearbox): Service Manual (single/ double-seat)

0

Filed Under (Dazon) by admin on 30-11-2010

download
1.2.1 Fuel Please use the gasoline of SAE 90# or above. Also we recommend you to use the unleaded gasoline. 1.2.2 Engine Oil Please use the high-quality engine oil of SAE 10w/30SF. 1.3 Break-in Procedure For your first 2 hours of riding, don’t exceed 2/3 throttles. Vary the engine speed for the first 5 hours. Never hold the engine at full throttle for long periods of time. Raider-Classic 150 (Oil-cooled&Internal Gearbox): Service Manual (single/ double-seat) EEC Version;3.0 Feb..2005 5 1.4 Specifications DIMENSIONS SINGLE-SEAT / DOUBLE-SEAT Overall Length 2330mm / 2300mm Overall Width 1310mm / 1460mm Overall Height 1425mm / 1425mm Wheelbase 1475mm / 1520mm Ground Clearance 200mm VIN Accord with GMVR A01-01 Statutory Plate& Safety Labels Accord with GB 7258-1997 ENGINE Model DZ1P57QMJ Type Oil-cooled, single cylinder, 4-Stroke Engine Capacity 150cc Displacement 149.6ml Bore X Stroke 57.4mm X 57.8mm Max Power 7.0kw or 7000r/m Max Torque 10.0N.m or 6500 r/m Idle Speed 1700 ± 100 r/m CO Emission 7.0g/km HC Emission 1.0g/km Fuel Type SAE 90# or above (unleaded) Lubricate Oil Type SAE 10W/30SF Lubrication Force & Splash Cooling Oil-cooled Ignition C. D. I. Starting Electric Spark Plug C7HSA (NGK) Spark Plug Gap 0.6~0.7mm Transmission Chain Transmission Gearbox Transmission Ratio F.:7.8:1 ; B.:11.297:1 Compression Ratio 9.5 ± 0.1 : 1 Carburetor MIKUNI BS 24-1005 Absorber Normal (in 10 5 times of experiments) CAPACITIES Front/ Rear Tire Load Coefficient 36 Front/ Rear Tire Speed Level L Fuel Tank 7.0L, 130kpa (no leakage in experiments) Engine Oil 1000ml Gear Oil 200ml Starting Time ≤15s Climbing ≥20%

Incoming search terms:

MPS Electronic Engine Kill Installation Instructions

0

Filed Under (Tips and Review) by admin on 27-10-2010

download
blue wire should be connected to the normally open pole of the shift button. The Shift Button is a momentary type switch. The common pole of the shift button should be connected to a good ground and the normally open connects to the blue wire from the Electronic Engine Kill box. Electric Air Valve – The Electric Air Valve has two wires. These wires are interchangeable. One needs an ignition switched 12 volt power source. The other needs a ground signal when the shift button is depressed. The easiest way to do this is to locate the red and blue wires in the Electronic Engine Kill wire harness. Splice one Electric Air Valve wire into the red wire and splice the other Electric Air Valve wire into the blue. Once again soldering is the preferred method but you can use schotchlok splices. Setting Kill Time – Kill time is the amount of time the engine stays dead between gears during a shift. Generally the shorter the kill time the quicker the shift. The proper kill time will vary from bike to bike. Its generally better to start with to much kill time and work your way quicker. We generally start at around 75 ms. of kill time. The Kill Time is adjusted via a small potentiometer accessed through the grommet on the front of the unit. Using a small screwdriver Carefully turn the pot clockwise to the end of its travel. This is 100 ms of kill time. Now, carefully turn the pot screw counterclockwise to the end of its travel. This is 50 ms of kill time. Halfway in between is 75 ms. The pot only goes from 7 oclock to 5 oclock so don’t force it, they break easily! Testing The System – With no air in the system start the bike. Bring the rpm up to around 3000 rpm and push the shift button. You should hear a slight hesitation in the engine each time you depress the shift button. Once you establish that you have a engine kill when pushing the shift button remove the clevis pin from the shift cylinder and extend the shaft to the end of its travel. Air up the shifter to 120 psi. We also have onboard compressor kits available to conveniently fill the air tank on the fly or high pressure CO2 systems that can shift hundreds of times without refilling. With the engine off and the key on push the shift button

Remote Starter Integration for the 2007 Toyota Camry equipped with the Smart Key System with Push Button Start

0

Filed Under (Toyota Manuals) by admin on 15-06-2011

Download
Most of the connections will be done behind the Fuse box. This fuse box is located under the driver side underdash. Also, the vehicle’s TACH wire can be found inside vehicle, as per diagram below and it
is suggested to use this wire for the remote start tach source. The remote start hood pin
switch wire is the only wire which must be run into the engine compartment for safety

2011 FORD HARLEY-DAVIDSON F-150 TECHNICAL SPECIFICATIONS

0

Filed Under (Harley Davidson) by admin on 01-11-2010

download
Final assembly location Dearborn Truck Plant, Dearborn, Mich. POWERTRAIN AND CHASSIS ENGINE Type 6.2-liter two-valve V8 Configuration Iron block, aluminum heads Valvetrain SOHC, two valves per cylinder, roller-rocker shaft with hydraulic lash adjusters Bore x stroke 4.02 x 3.74 inches Displacement 379 cubic inches, 6,210 cc Compression ratio 9.8:1 Horsepower 411 hp @ 5,500 rpm Torque 434 lb.-ft. @ 4,500 rpm Fuel Injection Sequential multi-port electronic Oil capacity Seven quarts DRIVETRAIN Layout RWD or AWD TRANSMISSION Standard Six-speed automatic overdrive Gear ratios 1st 4.17:1 2nd 2.34:1 3rd 1.52:1 4th 1.14:1 5th 0.86:1 6th 0.69:1 Reverse 3.40:1 Available axle ratios 3.73 SUSPENSION Front 4×2 Coil-on-shock, long-spindle double-wishbone independent, stamped-steel lower control arm (sport-tuned) Front 4×4 Coil-on-shock, long-spindle double-wishbone independent, stamped-steel lower control arm (sport-tuned) Rear 4×2 Hotchkiss-type non-independent live, leaf springs and outboard shock absorbers (sport-tuned) Rear 4×4 Hotchkiss-type non-independent live, leaf springs and outboard shock absorbers (sport-tuned) STEERING Type Power rack-and-pinion Turning circle curb-to-curb 47.0 feet 2011 FORD HARLEY-DAVIDSON F-150 TECHNICAL SPECIFICATIONS BRAKES Front 13.8-inch vented disc Rear 13.7-inch vented disc Assist type Vacuum, RSC WHEELS AND TIRES Wheels 22-inch polished forged aluminum with painted accents with “Harley- Davidson” Bar & Shield logo on wheel ornament Tires P275/45R-22 all-season BSW DIMENSIONS (inches unless otherwise noted) EXTERIOR SuperCrew RWD SuperCrew AWD Wheelbase 144.5 144.5 Vehicle length 231.9 231.9 Vehicle width (without mirrors) 79.2 79.2 Vehicle height 74.8 75.9 Track width, front/rear 67.0/67.0 67.0/67.0 Cargo box length 67.0 67.0 Width (max) between wheels 50.0 50.0 Inside box height 22.4 22.4 INTERIOR Seating capacity Five Five Headroom Front row 41.0 41.0 Rear row 40.3 40.3 Legroom Front row 41.4 41.4 Second row 43.5 43.5 Shoulder room Front row 65.9 65.9 Second row 65.5 65.5 Hip room Front row 60.5 60.5 Second row 64.6 64.6 WEIGHTS AND TOWING (pounds)

Incoming search terms: