sales com us mail

You search Auto repair manual PDF sales com us mail, if there are search results will appear below. If search results do not exist, please search by others keyword.



  sales com us mail Direct Download speed 5282 Kb/s

  sales com us mail Full Version speed 6162 Kb/s



Harley Davidson BoonDocker Nitrous System Installation MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2012

download
BoonDocker Liquid Nitrous – 1589 Hollipark Dr. Idaho Falls, ID 83401 – (208) 542-4411 web site: www. boon dockers. com – email: info@boon dockers. com Revised 02-27-04 Page 2 of 10 This manifold is also designed to vary the float bowl pressure in relation to nitrous pressure, thus keeping the nitrous and fuel delivery in sync. Fluctuations in bottle temperature greatly affect nitrous pressure, which affects nitrous delivery. By automatically adjusting the fuel delivery as nitrous pressure varies, this manifold makes nitrous safe, reliable, and easy to use. Be sure to understand and follow the tuning instructions at the end of these instructions. Proper tuning is an important part of any performance-enhancing product. Part I – Bottle Installation A. Bottle Valve Fittings Insert the 4AN x 1/8″ NPT fitting and the 1/8″ NPT Plug into the bottle valve (these are attached to the lid of the box for the bottle) . Use Teflon tape to seal the threads – be sure not to get tape inside the threads! B. Bottle Mounting Position With nitrous in the bottle, both nitrous liquid and nitrous gas are present under high pressure (760 psi at 70 deg F) . Due to gravity and acceleration forces, the liquid portion of the nitrous will be at the bottom and rearward parts of the bottle. For this nitrous system to work properly, it is important that nitrous liquid be drawn from the bottle. Nitrous vapor will cause a significant decrease in performance. For best results, the bottle should be mounted so the valve is pointed down and towards the back of the vehicle as shown below. ************** *************** ******** ********* *************** (can be installed on top or bottom of air boot) ********** ********* push-button switch (mounts on handlebar) +12 V *********** ************ **** ****** *! “**#$******%* *! “**#$*#*%* 20 deg to 90 Front of motorcycle Rear of motorcycle BoonDocker Liquid Nitrous – 1589 Hollipark Dr. Idaho Falls, ID 83401 – (208) 542-4411 web site: www. boon dockers. com – email: info@boon dockers. com Revised 02-27-04 Page 3 of 10 Bottle mounted inside airbox: For some applications, a small bottle can be mounted inside the airbox as shown. Note: because of the restricted space, it was necessary to mount this bottle at a non-optimal angle (the valve is pointed towards the front instead of the rear)

Incoming search terms:

Kawasaki VN1600 Highway Bar INSTALLATION AND OWNER'S MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
PREPARATION 1. Insure that the motorcycle is on flat level ground. 2. It is recommended that the motorcycle sit for at least one hour prior to installation to allow the engine to cool. During installation tight all fasteners to hold. Wait until you check all clearances and operation of the brake and shift lever to firmly tighten and torque all fasteners. INSTALLATION Right Side Highway Bar 1. Remove the front floor board bolt (M10). (14mm Socket) Figure 1. Right and Left side of Motorcycle is determined while sitting on the bike.
MAINTENANCE / CAUTION The high quality chrome finish of your National Cycle Chrome Highway Bar can be maintained with any quality chrome cleaner and / or polish applied with a soft cloth. Check hardware for tightness regularly. Never ride with loose mounting hardware. Check to be sure your Highway Bar does not contact any part of the motorcycle at a full turn left and right. Correct any problem before using the motorcycle. ©2005 National Cycle, Inc. PO Box 158, Maywood, IL60153-0158 USA 708-343-0400 / Fax: 708-343-0625 / www.nationalcycle.com / e mail: info@nationalcycle.com Page 2 of 2 10-114857-000 09/05 Install Upper “U” Bolt 2. Place “U” Bolt between the radiator and the down tube at the location shown in Figure 2. Threaded ends of “U” will face out- ward. 3. Select the right side Highway Bar. 4. Loosely install the Highway Bar at the lower mount point using the stock screw. (14mm Socket) Figure 3. While installing the Whizlock Nuts in the following Step #5 , be certain to tighten the nuts evenly, alternating left and right as you tighten. When complete you want the same amount of threads exposed on the ends of the “U” to insure the bolt does not rotate. 5. Install the upper Highway Bar with Whizlock Nuts. (1/2″ Socket) Figure 4. Orient assembly so Whizlock Nuts face outside. Firmly tighten after all clearances are checked. LEFT SIDE INSTALLATION 6. Repeat Steps 1 and 2. On the Left Side due to tight clearances between the radiator and the down tube you must locate the point where the radiator is “notched out” slightly. Figure 5. 7. Select the left side Highway Bar. 8. Repeat Steps 4 and 5.

Yamaha V-Star 1100 Needle/ Jet Kit REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Honda) by admin on 27-12-2011

download
To install this needle and jet kit: • Remove carburetors from the engine per Yamaha shop manual procedures. Note: Always perform internal carburetor work in a clean area. • Remove the vacuum slide from each carburetor. • Remove the OEM needle, spacer and washers, noting order of assembly. (Note; the washers are used as shims to raise the needle, each is equivalent to ½ clip position, use these to fine tune the needle) • Counting from the top to the bottom, install the new Baron needle clip on groove #4 of the replacement Baron adjustable needles. The top is the blunt end of the needle. • Reinstall the OEM spacer and washers as shown in the figure below. • Reinstall the vacuum slides along with the diaphragm spring and reattach the diaphragm covers Note: Verify that the slides maintain their full range of movement! • Drain the fuel from the float bowls and remove the bowl covers. • Remove the OEM main jets and replace them with Baron’s supplied Mikuni main jets. Install the “base setting” main jets as indicated above. NOTE: V-Star 1100 carburetion runs staggered jetting! Make sure the front cylinder’s carburetor gets the larger main jet (numerically), and the rear cylinder’s carburetor gets the smaller main jet . Important! Extra jets have been included in your kit. These will help you fine-tune the carburetors for changing conditions. These conditions include climate and weather patterns in your area as well as exhaust equipment on your motorcycle. Barons determines the jet and clip recommendations that best suit your average riding conditions based upon information supplied to us at the time of your order. Changes in weather, altitude or modifications to your exhaust system may require jets other than those supplied. • Thoroughly clean the inside of the float bowls prior to reinstalling them. 311 #1 Industrial Way – Fallbrook, CA 92028 – USA Phone: (760) 731-1200 Fax: (760) 731-1284 E-mail: tech@baronscustom.com Website: www.baronscustom.com Included in this kit: (4)Mikuni main jets #107.5, 110, 112.5, 115, (2) titanium needles, (2) clips, (8) cap-head allen screws Tools required: 3-4-5 mm allen wrenches, 10&12 mm sockets, 10mm end wrench, phillips & flat screwdrivers, pliers, drill. Revision 4.0 • Reassemble the carburetors by reversing the order of above steps. Use the new supplied cap head Allen screws in place of the OEM Phillips head screws for the float bowls. • Locate the fuel mixture screws – they will either be a screw head or a brass plug. If it is a screw head, skip to step c . If you see a brass plug with a small hole in the center, proceed as follows: a. With a 5/32″ drill bit, carefully and slowly drill through the fuel mixture plugs

Yamaha V-Star 650 Jet Kit REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 16-01-2012

download
Remove the vacuum slide from the carburetor. • Remove the OEM needle and spacer, noting the order of assembly. • Counting from the top to the bottom, install the new Baron needle clip on groove #4 of the replacement Baron adjustable needle. • Reinstall the OEM spacer and washer. • Reinstall the vacuum slide along with the diaphragm spring. • Reattach the diaphragm cover and tighten its screws. Note: Verify that the slide maintains a full range of movement! • Drain the fuel from float bowl and remove the bowl cover. • Remove the new cap head Allen screws in place of the OEM Phillips head screws. • Repeat above steps for other OEM main jet and pilot jet, and replace them with Baron’s main and pilot jets. • Thoroughly clean the inside of the float bowl prior to reinstalling it. • Reassemble the carburetor by reversing the order of previous steps. Use thecarburetor. • Locate the fuel mixture plug on each carburetor; it will either be a screw head or a brass plug. If it is a screw head, skip to step c . If you see a brass plug with a small hole in the center, proceed as follows: a. With a 5/32″ drill bit, carefully and slowly drill through the fuel mixture plug for each carburetor. CAUTION: The fuel mixture screw is located directly beneath this plug. Be prepared to stop the drill and remove the bit the instant you break through the plug. b. Insert a self-tapping sheet metal screw into the drilled hole and remove the plug. 311 #1 Industrial Way – Fallbrook, CA 92028 – USA Phone: (760) 731-1200 Fax: (760) 731-1284 E-mail: tech@baronscustom.com Website: www.baronscustom.com Included in this kit: (2) Mikuni main jets, (2) pilot jets, (2) titanium needles, (2) clips, (8) cap head Allen screws Revision 2.0 c. With air/fuel screw now accessible, use a flat blade screwdriver to turn the screw clockwise until it seats, then carefully turn it counter-clockwise 3 turns. Refer to final step for assistance in fine-tuning the setting of the air/fuel adjustment screw. • Reinstall the OEM air filter assembly. • Check all vent lines, fuel lines, and linkage for any obstructions or blockage

Suzuki M 109 WINDSHIELD INSTALLATION AND OWNER'S MANUAL

0

Filed Under (Suzuki) by admin on 18-02-2012

download
Position the motorcycle securely on its stand or a work stand. Cover the front fender and fuel tank with a cloth to avoid scratches from dropped tools. 1. Use the above diagram toidentify left from right Lower and Upper Mount Brackets. Figure 1 2. Cut each of the clamp spacers in half to make 8 pieces, each 2.5 x 1.55″. 3. Apply one spacer to the inside of each mount bracket. Figure 2 Figure 1 Figure 2 N28201 and N28202 WINDSHIELD INSTALLATION AND OWNER’S MANUAL for Suzuki®M109 Right and Left side of Motorcycle is determined while sitting on the bike. Determine left from right Upper bracket. Washer angles inboard about 5 degrees. Note, Angle distinguishes Right from Left Lower Mount Bracket 1 2 4 3 5 6 8 9 10 National Cycle, Inc. Maywood, IL 60153-0158 USA 708-343-0400 / Fax: 708-343-0625 www.nationalcycle.com / e mail:info@nationalcycle.com Page 1 of 3 10-114056-000 08/07 / Rev B. 03/08 7 3, Left Upper Bracket 4, Right Upper Bracket About 5 0 inboard angle
INSTALLATION Measurements provided for clamp location. From this point you can adjust the brackets 1″ (22mm) higher if you prefer keeping in mind, position of the front nose of windshield should have a minimum of 1/2″ (13mm) clearance from cowling . Figure 3. Right Side Lower Mount Assembly 1. Start on the Right Side of motorcycle. At the top of the fork, place one inner black clamp on the fork tube. Figure 4 2. Hook the RIGHT SIDE lower mount bracket (2) to the inside clamp. Figure 5 3. Slide assembly down fork so bottom edge of bracket is 1.75″ (44mm) from top of lower triple clamp. Adjust bracket so flat in bracket runs parallel with motorcycle. Figure 6 and 7 4. Loosely install one M8 x 16 screw. (6mm Hex Key) Figure 7 Right Side Upper Mount Assembly 5. Place the second inside black clamp on the right fork tube.

BMW Motorcycles F 650 GS Dakar fuel tank replacement

0

Filed Under (BMW) by admin on 12-11-2010

download
Your center has been requested in a recent e-mail, to forward VIN, color Information: and status information on all F 650 GS(A) and Dakar models remaining in your inventory. Fuel tanks, together with the appropriate colored trim pieces, will be forwarded to your center for each bike in your inventory as replacement parts arrive in BMW NA inventory. Warranty Please enter a warranty campaign claim , encompassing the following Reimbursement: Work Package information, when claiming reimbursement for the updates called for in this bulletin. Even though there is no charge for the parts, a sublet of $60.00 will be applied to each claim. This sublet amount is intended as a combination of both the handling and as reimbursement for incidental items that may be required in the replacement of the fuel tank. Work Package #1 is to be used in the replacement of all F 650 GS(A) and Dakar model fuel tanks. Defect Code: 00 00 16 1100 Description: Fuel Tank – Leaking Flat Rate Code: 00 60 059 Description: Remove and reinstall fuel tank (USA only) FRU: 12 FRU Sublet #4: $60.00 Pick up & In the recent Sales and Marketing Bulletin # B23/00 introducing the “Customer Delivery: Demonstration Program”, (e-mailed to your center on September 7, 2000), each BMW motorcycle retailer was asked to arrange to pick up, complete the updates and deliver the motorcycle back to the customer and to offer the use of a demonstrator where appropriate.

Incoming search terms:

2010 Toyota Motorsports/ TRD USA Contingency Award Program

0

Filed Under (Toyota Manuals) by admin on 29-09-2011

download
To enroll in the program, complete the registration form included in the enclosed material and mail, fax or e-mail it to TRD per the instructions at the bottom of the form. Contact personnel are listed on the attached 2010 Contingency Award Guidelines sheets. These people are available to assist you throughout the year. Parts Ordering: If you are planning to order Toyota parts during 2010 you must supply us with your Visa or Master Card credit card number at the time you register in the program. There is a line on the registration form for this number. See the attached Parts Ordering Guidelines for detailed information on how to order parts. TRD is looking forward to working with each of you, and we wish you a very successful year with your racing program

Incoming search terms:

1997 Honda CBR 1000 F specifications

0

Filed Under (Honda) by admin on 03-11-2010

download
Front brakes: Dual disc Rear brakes: Single disc Speed and acceleration Top speed: 255.0 km/h (158.4 mph) Power/weight ratio: 0.5745 HP/kg Other specifications Further information Parts and accessories Check out parts and accessories from our partners. Ask questions Join the 97 Honda CBR 1000 F discussion group Insurance, loans, tests Search the web for dealers, loan and insurance costs, tests, customizing, etc. Related bikes List related bikes for comparison of specs Buying a bike starts at Bikez Get a list of related motorbikes before you buy this Honda. Inspect technical data. Look at photos. Read the riders’ comments at the bike’s discussion group. And check out the bike’s reliability, repair costs, etc. Show any 1997 Honda CBR 1000 F for sale on our Bikez.biz Motorcycle Classifieds. You can also sign up for e-mail notification when such bikes are advertised in the future. And advertise your old MC for sale. Our efficient ads are free. You are also welcome to read and submit motorcycle reviews. Rating sample for this Honda bike Value for money for the 1997 Honda CBR 1000 F: (67.1 out of 100) Click here for complete rating. You can also compare bikes. Pictures, trademarks and logos of third parties are exclusive property of the respective owners. Technical specifications are subject to change without notice. Bikez.com has been developed by low-cost software development company ObjectLabs

Incoming search terms:

Hot-Start Kit For Yamaha YZ/ WR 400F

0

Filed Under (Yamaha) by admin on 16-12-2010

download
Blaster Rear Brake Kits 121-01298 • YFS200 Blaster ’88-’98 • This cable will eliminate the stock cable from the handlebar. Cable will go from the rear brake pedal to the caliper. 121-01299 • Same as 121-01298 +4″ • Cable is 4″ longer for extended swingarms. 121-01027 Replacement Ratchet Spark Plug Wrench 121-08147 • Designed specifically to fit where there is limited space • Ratchet mechanism works one way • Fits standard 13/16″ plugs
INDEX PAINT HANDLEBARS STREET LEVERS FORK SEALS CABLES SUSPENSION ELECTRICAL FILTERS BRAKE LINES BRAKES CABLE MAKING SUPPLIES CONTROLS DUAL SPORT MANUALS FSO PRODUCTS EMGO DRIVE DISPLAY JETS BEARINGS EYEWEAR VINTAGE MIRRORS EUROPEAN KICKERS SHIFTERS MISC HARD PARTS SHOP TOOLS CHEMICALS TOOLS R . 03-15-06 21 (626) 792-7384 www.FlandersCompany.com Fax: (626) 792-5341 www.FlandersCo.com Specialty Tools Swingarm Bearing Tool 121-080213 • Designed for installation of the swing arm bearings on late model Japanese motorcycles • Using the correct size insert (various sizes included in kit) and the puller, the mechanic can draw the bearing into the swingarm without beating on it with a hammer Main Jet Wrenches • High-quality die cast construction • 6mm round and hex jets and 8mm round • Cap holds a few spare main jets • Sold each 121-08023 6mm Hex (Fits 6mm hex main jets) 121-08024 8mm Round (Fits 8mm round main jets) 121-08025 6mm Round (Fits 6mm round main and pilot) Allen Extension 121-080184 • 5mm allen on a 6.25″ long, 3⁄8-drive extension for hard-to-reach case bolts • Designed for use with air tools • Great for splitting engine cases

2005 Kawasaki ZX6R Power Commander Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the tail section by removing the undertail and removing the six screws for the tail section. 2 Prop the front of the fuel tank up. 3 Lay the PCIIIin the tail section and route theharness along side the stock wiring harness towards the throttle bodies (Fig. B&C). Fig. A Fig. B Fig. C 2005 Kawasaki ZX6R – PCIII USB – 2 i218-411 www.powercommander.com PCIII harness PCIII harness Remove these screws 4. Disconnect the stock wiring harness from the LOWERinjectors at the throttle bodies (Fig. D). 5. Plug the PCIII connectors in-line of the stock injectors and wiring harness. ORANGE – cylinder 1 YELLOW- cylinder 2 GREEN – cylinder 3 BLUE – cylinder 4 6. Locate the Throttle Position Sensor connector behind the throttle bodies. This is a WHITE 3 pin connector (Fig. F) Fig. D Fig. E Fig F 2005 Kawasaki ZX6R – PCIII USB – 3 i218-411 www.powercommander.com PCIII connectors TPS connector Disconnect Stock connectors 7. Plug the PCIII harness in-line of the stock wiring harness (Fig. G). 8. Attach the ground wire from the PCIII to the negative side of the battery (Fig. H)

Incoming search terms: