scooter diagnostic tester

You search Auto repair manual PDF scooter diagnostic tester, if there are search results will appear below. If search results do not exist, please search by others keyword.



  scooter diagnostic tester Direct Download speed 5282 Kb/s

  scooter diagnostic tester Full Version speed 6162 Kb/s



DIAGNOSTIC TESTER CONTROLLER AREA NETWORK (CAN) INTERFACE MODULE

0

Filed Under (Toyota Manuals) by admin on 30-10-2011

download
Remove the original DLC3 Cable and store it in the Diagnostic Tester storage case. 2. Connect the CAN Interface Module to the DLC Cable. 3. Use the Diagnostic Tester with the CAN Module installed for all DLC3/J1962 based vehicle communication. 4. If you experience problems with the Diagnostic Tester or CAN Interface Module, please contact Toyota Special Service Tool Customer Support at 1-800-933-8335. NOTE: There is no need to remove the CAN Interface Module when working with non-CAN systems or older software versions (Version 10.1a or earlier). The Diagnostic Tester will communicate with all DLC3/J1962 based systems with the CAN Interface Module installed. For DLC1 and DLC2 communication you must continue to use the Vehicle Interface Module (VIM)

2001 YAMAHA TDM900 SERVICE MANUAL

0

Filed Under (Yamaha) by admin on 20-11-2010

download
CHECKING THE SWITCHES ELEC EAS00731 ELECTRICAL CHECKING THE SWITCHES Check each switch for damage or wear, proper connections, and also for continuity between the terminals. Refer to “CHECKING SWITCH CONTINUITY”. Damage/wear Repair or replace. Improperly connected Properly connect. Incorrect continuity reading Replace the switch. -3- ELECTRIC STARTING SYSTEM ELEC EAS00755 ELECTRIC STARTING SYSTEM CIRCUIT DIAGRAM -4- ELECTRIC STARTING SYSTEM ELEC 4 Main fuse 5 Battery 7 Starter relay 8 Starter motor 9 Main switch 12 Starting circuit cut-off relay 13 Sidestand switch 14 Neutral switch 49 Clutch switch 59 Engine stop switch 60 Start switch 61 Ignition fuse -5- ELECTRIC STARTING SYSTEM ELEC EAS00756 STARTING CIRCUIT CUT-OFF SYSTEM OPERATION If the engine stop switch is set to “” and the main switch is set to “ON” (both switches are closed), the starter motor can only operate if at least one of the following conditions is met: The transmission is in neutral (the neutral switch is closed). The clutch lever is pulled to the handlebar (the clutch switch is closed) and the side- stand is up (the sidestand switch is closed). The starting circuit cut-off relay prevents the starter motor from operating when neither of these conditions has been met. In this instance, the starting circuit cut-off relay is open so current cannot reach the starter motor. When at least one of the above conditions has been met the starting circuit cut-off relay is closed and the engine can be started by pressing the starter switch. WHEN THE TRANSMISSION IS IN NEUTRAL WHEN THE SIDESTAND IS UP AND THE CLUTCH LEVER IS PULLED TO THE HANDLEBAR 4. Starting circuit cut-off relay Disconnect the starting circuit cut-off relay from the wire harness. Connect the pocket tester (Ω 1) and battery (12 V) to the starting circuit cut-off relay terminals as shown. YES NO Replace the starting circuit cut-off relay. Does the starting circuit cut-off relay have continuity between blue/white and black? EAS00759 Continuity Tester positive probe sky blue Tester negative probe blue/yellow No conti- nuity 1 2 1 3 Tester positive probe sky blue Tester negative probe black/yellow Battery positive terminal red/black Battery negative terminal black/yellow 1 2 Tester positive prove blue/white Tester negative prove black 3 4 5. Starting circuit cut-off relay (diode) Disconnect the starting circuit cut-off relay from the wire harness. Connect the pocket tester (Ω 1) to the starting circuit cut-off relay terminals as shown. Measure the starting circuit cut-off relay for continuity as follows. Tester positive probe blue/green Tester negative probe blue/yellow 4 3 Tester positive probe black/yellow Tester negative probe sky blue 2 1 Tester positive probe blue/yellow Tester negative probe sky blue 3 1 Tester positive probe blue/yellow Tester negative probe blue/green 3 4 When you switch the tester’s positive and negative probes, the readings in the above chart will be reversed. Are the testing readings correct? YES NO Replace the starting circuit cut-off relay. NOTE: EAS00760

Incoming search terms:

WILDFIRE WFH50-S2 Gas Scooter Owner's Manual

0

Filed Under (Tips and Review) by admin on 21-11-2010

download
Main Switches On Position: • Electrical circuits are switched on. The engine can be started and the key can not be removed. • Do not leave the main switch in the on position for an extended period of time if the engine is not running Off Position: • All electrical circuits are off and the engine is stopped. The key can be removed in this position. Steering Lock Position: • Turn the handlebars to the left as far as they will turn, turn the key to the lock position and remove. Steering Lock Position On Position Off Position Wildfire WFH50-S2 Maintenance Table The X indicates at how many miles you need to check the Item. Must change oil: change before riding, again at 500 miles and then 2500 or yearly which ever comes first. Capacities Fuel Capacity: 1 gallon Final drive oil capacity: 3.5 ounces Tire air pressure: Front 28 psi and rear 32 psi. ITEM 500 1000 20002500 3500 40004500 5000 60006500 Check Daily Engine Oil and Filter X X X X X X Gear Oil X X X X Valve Clearance X X Cam Chain X X Carburetor X X Air Cleaner Clean Every 1500 miles, Replace Every 3500 miles Fuel Filter Clean Every 1000 miles, Replace if Necessary Brake System X X X X X X X Drive Belt X Screws and Nuts X X X X X *When riding in a dusty environment, check and clean the air filter element more often. Battery • This scooter uses a sealed lead acid battery, it is unnecessary to check or add liquid. NOTE: Never open the electrolyte of a sealed battery. Remove the battery from the scooter and store separately in a well ventilated area when the scooter is not in operation for long periods of time Speedometer • Speed is measured in mph. Odometer • The total riding distance is indicated. Fuel gauge • The gauge indicates how much fuel is in the tank (the gauge does not work when the ignition switch is off). The needle moves from full “F” to empty “E” as your fuel decreases. Fill the tank with a good grade of 89-90 octane unleaded gasoline. High Beam Indicator LIght • The high beam light indicates that the high beam headlight is in use. NOTE: Apply the low beam to avoid obstructing the view of other drivers. Turn Signal Indication Light • The turn signals indicate that you are turning a chosen direction, push the button in the desired turning direction, it will return to the center, press the button in to turn off. Speedometer Odometer Turn Signal Indication Light High Beam Indication Light Fuel Gauge 4 General Safety Precaution • Scooters can be hazardous to operate. Please operate it with the following safety instruction. If you fail to take proper precautions, a collision or fall may quickly occur. If you have any questions as to the operating condition of your scooter, turn off the engine and walk your scooter. These scooters should be ridden by persons with good vision, balance, coordination, reflex, strength and decision making capability. • Please read this manual and all safety labels carefully, and follow correct operating procedures. • Before each time you ride make sure that the brakes work properly. • Never operate your scooter without wearing proper safety equipment that includes helmet, shoes, etc… • Never operate your scooter under influence of alcohol or drugs. • Always ride with both hands on the handle bars. • Never operate at excessive speeds. Proper speed is determined by terrain, visibility, operating condition and experience. • Never attempt wheelies, jumps or other stunts. • Always inspect your scooter prior to each use to make sure all bolts are tight, and is in safe operating condition.

Incoming search terms:

BMW MOTO-1 diagnostic scanner user manual

0

Filed Under (BMW) by admin on 24-11-2010

download
1. When testing the motorcycle ECU with the diagnostic scanner, it displays “Communication failure!” what is the problem? How to deal with it? This problem is caused by the reasons as below: 1.1 The ECU model of diagnostic program you choose is different from the ECU model of motorcycle. Some motorcycles are modified. At this time, you can check the detailed model of the ECU, and choose the actual model from the “ECU MODEL” menu to test. 1.2 The ignition switch hasn’t turned on to the “ON” position. 1.3 The cable between the diagnostic scanner and the diagnostic connector of motorcycle isn’t connected reliable. 2. After electrifying the diagnostic instrument, press the switch of the mainframe, it displays white screen or black screen. What is the problem? How to deal with it? 2.1 Maybe you adjusted the adjustable knob of the mainframe by accident to lead the white screen or black screen of the mainframe. After starting up normally, adjust the offside adjustable knob on the top of the mainframe screen to make the mainframe display normally. 2.2 Check the power supply voltage of the diagnostic scanner is normal or not.

Incoming search terms:

Wildfire WFH 150-T Touring Scooter Specification And Owner's Manual

0

Filed Under (Wildfire) by admin on 29-11-2010

download
Engine Oil Replacement • Replace the engine oil after the first 50 miles or 1 hour with 5w50, 10w50 or 15W50 synthetic engine oil. Then replace again every 1,500 miles or 1 each year. Check oil level every 500 miles, add oil if needed. Changing the Engine Oil (1).Warm up the engine for a few minutes. (2).Stop the engine. (3). Place scooter on center stand. (4).Place an oil pan under the engine and remove the dipstick. (5).Remove the drain plug and drain the oil. Reach in drain hole, pull out filter clean and reinstall, after all oil drains out. (6).Reinstall drain plug. (7). Fill the engine with oil until the level is in the designated area on the dipstick. (8).Start the engine and check for oil leaks. If a leak is found stop the engine immediately and look for cause. Rear Wheel Oil Replacement • Replace the gear oil after the first 500 miles with 5W/50 synthetic engine oil. Replace the gear oil again every 4 months or every 2000 miles. • Replacing the Gear Oil (1).Put the scooter on the center stand (please see photo below) . (2).Place an oil pan under the gear case (please see photo below) . (3).Remove the oil filler bolt and the drain plug to drain the oil (please see photo below) . (4).Reinstall and tighten the drain plug. (5).Fill the gear case with oil (please see photo below) . (6).Reinstall the oil filler bolt. (7).Check for oil leakage. Cleaning Air Cleaner Be sure to check the air cleaner regularly. (1).Place the scooter on the center stand. (2).Unscrew and remove the left side panel. (3).Remove the air cleaner cover by removing the screws. (4).Take out the air cleaner by removing the screws. (5).Remove the air cleaner element and wash it gently, but thoroughly in solvent. Replace if damaged. (6).Squeeze out the excess solvent and dry it. (7).Apply oil to the entire surface of the air cleaner and squeeze out the excess oil. It should be damp but not dripping. (8).Install the air cleaner, cleaner cover, and left side panel. center stand 1 oil pan 2 3 oil drain plug oil pan 5 Main Switches On Position: • Electrical circuits are switched on. The engine can be started and the key can not be removed.

Scooter VESPA G.S. MAIN SPECIFICATION

0

Filed Under (Vespa) by admin on 11-11-2010

download
Engine: Single cylinder, two-stroke, with reverse flow scavenge and high volumetric efficiency. Flat cast iron cylinder and pressure die ; cast, special aluminium alloy cylinder head. High strength, steel con. rod connected, trough a row of rollers, with the crankshaft which is built of three parts. Bore 57 min. (2.24°) Stroke 57 mm. (2.24″) Displacement 145.55 cc. (8.82 cu in.) Compression ratio 7 to 1 Starting: By means of kick-starter, right hand side of scooter. Transmission: Directly from engine to rear wheel through clutch, cush drive and gear box. . Fig. 02 – VESPA controls 1 – Fuel cock 2 – Throttle control grip 3 – Clutch control lever 4 – Front brake lever 5 – Horn 6 – Horn button 7 – Dimmer switch 8 – Gear change twistgrip 9 – Contact key 10 – Rear broke pedal 11 -Kick- starter 12 – Choke ro Gear change: 4 – speed drive with mesh gears in oil bath. Its adjustable twistgrip control is coupled with that of the clutch, on left hand side of handlebars (fig. 2). Clutch: Wet type; steel plates with cork inserts. Control by lever, on left hand side of handlebars, and adjustable cable. Ignition: By 6-pole flywheel magneto. Separated ignition coil with primary circuit fed by another coil inside the flywheel magneto. Lighting and horn: By flywheel magneto, with a. c. directly feeding head lamp (double filament bulb, 6 v, 25/25 w), and tail lamp, 6 v, 5w, when the switch is in position “2″. The town light (6 v, 3 w), tail lamp, STOP light and horn are fed by the 12 Ah battery, which is constantly re-charged through a metallic rectifier and impedance, when the key of the switch is in either position “0″ or “1″ (see Fig. 3). Frame: of special, thick steel sheet, pressed and spot welded, with streamlined monocoque type structure. Suspension: Front: stub axle and swinging hub with variable rate coil spring and double action hydraulic damper. Rear: swinging bracket for engine and wheel, with variable rate coil sprang and co-axial double action hydraulic damper.

Piaggio 250 Installation And Removal Manual

0

Filed Under (Piaggio) by admin on 28-10-2010

download
1. Secure scooter inastableupright position. 2. Attach bracket E to underside of scooter frame -Forward cross brace on E attaches to existing holes on underside of scooter frame. Secure bracket E with new bolts provided. -Ensure bracket E is square with scooter and locate two rear holes on bracket E . Two rear holes on E will align with scooter frame rear cross brace. Drill 3/8 inch holes incross brace to align with rear holes on bracket E . Attach with bolts provided. 3. Attach top of bracket C (left) / D (right) to outside of rear shock mount using new bolt provided. NOTE: A shorter bracket Dis included and required on some MP3250 models. 4. Attach axles and wheels to MiniTrikeframe and orient frame in position behind scooter. 5. Attach bottom of C/D to rear mounting plate on Mini Trike frame

ELECTRIC SCOOTER Assembly and User's Manual

0

Filed Under (Tips and Review) by admin on 26-11-2010

download
l Output: 250W l Voltage: 24V DC l Rated current: 14.0A l Non-loading rotate speed: 3350±5% l Rated rotate speed: 2500 RPM l Rated torsion: 0.90 Battery l 12V 12Ah/5hr x (2) Qty l Sealed lead acid FEATURES & SPECIFICATIONS Performance l Maximum speed: 11 MPH l Range: Nine (9) miles l Incline rating: 40 l Net Weight: 45 lbs. l Maximum load cap.: 178 lbs. Tires l Tire Size: 2 1/4″ x 12 1/2″ l Tire Pressure: 45-50 PSI Key Ignition Headlight Turn Signals Turn Signals Brake Light Mag Wheels Footrests Working Gauges Quick Connect Charging 3
4 l One (1) SCOOT – N – GO™ l User/assembly manual l Tool kit containing 2 open ended wrenches, combination Phillips/Flathead head screwdriver l Spare fuses (30 Amp x 3 qty) l 24V Battery charger . Remove scooter from carton and all protective materials from the unit. 2. Use tool kit provided for installation FRONT WHEEL INSTALLATION: 1. Place wheel (D) in the center of the forks 2. Insert one (1) spacer (C) between wheel (D) and fork 3. Carefully insert axle (E) through fork, spacer (C), and wheel (D) 4.Insert one (1) spacer (C) on opposite side between fork and wheel (D) 5. Continue to insert axle (E) through fork on opposite side 6. Place washers (B) and nuts (A) on both ends of axle and tighten with open ended wrench provided in the tool kit. 7. Check nuts are tight and wheel moves freely Parts Needed A Nut Qty- 2 Lockwasher Qty- 2 B Spacer/ Bearing-holder Qty- 2 C D Front Wheel Qty- 1 E Axle Qty- 1 *Photos are not to scale Spacer Spacer Axle Washer Washer Nut Nut
10 ASSEMBLY INSTRUCTIONS HANDLEBARS INSTALLATION: 1. Insert handlebar post through tightening clamp 2. Insert the top of the fork base into bottom of handlebar post. 3. Line up handlebars and front wheel 4. Slide tightening clamp down to open end of fork base 5. Insert bolt and hand tightening nut into clamp and tighten. 6. Be sure that handlebars and wheel move at the same time

ABS Solenoid Relay Circuit TOYOTA

0

Filed Under (Toyota Manuals) by admin on 21-09-2011

Download
Start the inspection from step 1 in case of using the TOYOTA hand-held tester and start from step 2 in case
of not using the TOYOTA hand-held tester.1 Check ABS solenoid relay operation. PREPARATION: (a) Connect the TOYOTA hand-held tester to the DLC3. (b) Turn the ignition switch ON and push the TOYOTA hand-held tester main switch ON. (c) Select the ACTIVE TEST mode on the TOYOTA hand-held tester. CHECK: Check the operation sound of the ABS solenoid relay when operating it with the TOYOTA hand-held tester. OK: The operation sound of the ABS solenoid relay should be heard

Incoming search terms:

SUZUKI SV650 ELECTRICAL SYSTEM REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Suzuki) by admin on 26-02-2011

download
CAUTIONS IN SERVICING CONNECTOR • * When connecting a connector, be sure to push it in until a click is felt. • * Inspect the connector for corrosion, contamination and breakage in its cover . COUPLER • With a lock type coupler, be sure to release the lock before disconnecting it and push it in fully till the lock works when connecting it . • * When disconnecting the coupler, be sure to hold the coupler itself and do not pull the lead wires . • * Inspect each terminal on the coupler for being loose or bent . • * Inspect each terminal for corrosion and contamination. CLAMP • * Clamp the wire harness at such positions as indicated in “WIRE HARNESS ROUTING”. ( r- 79-14 to 9-16) • * Bend the clamp properly so that the wire harness is clamped securely. • * In clamping the wire harness, use care not to allow it to hang down. • * Do not use wire or any other substitute for the band type clamp. FUSE • * When a fuse blows, always investigate the cause, correct it and then replace the fuse . • * Do not use a fuse of a different capacity . • * Do not use wire or any other substitute for the fuse . i SEMI-CONDUCTOR EQUIPPED PART • * Be careful not to drop the part with a semi-conductor built in such as a ECM. • * When inspecting this part, follow inspection instruction strictly . Neglecting proper procedure may cause damage to this part . BATTERY • The MF battery used in this motorcycle does not require maintenance (e.g., electrolyte level inspection, distilled water replenishment) . • * During normal charging, no hydrogen gas is produced. However, if the battery is overcharged, hydrogen gas may be produced. Therefore, be sure there are no fire or spark sources (e.g., short circuit) nearby when charging the battery . • * Be sure to recharge the battery in a well-ventilated and open area. •Note that the charging system for the MF battery is different from that of a conventional battery. Do not replace the MF battery with a conventional battery . CONNECTING THE BATTERY •When disconnecting terminals from the battery for disassembly or servicing, be sure to disconnect the O battery lead wire, first. • * When connecting the battery lead wires, be sure to connect the OO battery lead wire, first . • * If the terminal is corroded, remove the battery, pour warm water over it and clean it with a wire brush . • * After connecting the battery, apply a light coat of grease to the battery terminals. • * Install the cover over the O battery terminal. WIRING PROCEDURE • * Properly route the wire harness according to the “WIRE ROUTING” section. (C’9-14 to 9-16) ELECTRICAL SYSTEM 8- 3
8-4 ELECTRICAL SYSTEM USING THE MULTI CIRCUIT TESTER •Properly use the multi circuit tester Oand Oprobes. Improper use can cause damage to the motorcycle and tester. • * If the voltage and current values are not known, begin measuring in the highest range . • * When measuring the resistance, make sure that no voltage is applied. If voltage is applied, the tester will be damaged . • * After using the tester, be sure to turn the switch to the OFF position. CAUTION Before using the multi circuit tester, read its instruction manual.