setting preload on 2015 xt 250

You search Auto repair manual PDF setting preload on 2015 xt 250, if there are search results will appear below. If search results do not exist, please search by others keyword.



  setting preload on 2015 xt 250 Direct Download speed 5282 Kb/s

  setting preload on 2015 xt 250 Full Version speed 6162 Kb/s



ACE -325X/ 395 X-XX CLOCK, UNIT, WHEEL, ODOMETER, TEMPERATURE & FUEL METER SETTING

0

Filed Under (Honda) by admin on 24-12-2011

download
Setup operations include 12/24hour clock, bar tachometer scale, shift warning RPM, numbers of engine rotation per signal, wheel circumference, units, odometer adjustment, units of temperature, temperature warning and fuel meter input resistance selection. These must be set up step by step. The computer will automatic reversion to main screen if no button operation for 75 seconds at any setting screen. 2. Press both MODE & RESET buttons to go into setting screen. In setting screens, press RESET button to add the flashing digit by 1 or convert units, press MODE button to confirm the digit setting and jump to next digit or next setting screen to be set. Press MODE button for 2 seconds at any setting screen to finish the setting and go to main screen. 3. It displays “12 or 24H and XX:XX-XX” symbols and AM/PM in case you select 12H. Operates buttons as descriptions of item 2 to finish clock and jump to 8,000/16,000rpm scale setting. 4. It displays 8,000rpm scale, presess RESET button to convert 8,000 or 16,000rpm. Press MODE button to confirm the setting and jump to shift RPM warning setting. 5. It displays ” RPM rXXX00 “. Follow the item 2 of button operation to finish the shift RPM warning setting and jump to engine specification setting. 6. It displays “SPC-X.X RPM”, the default value is 1.0; there are 4 options: 1.0, 2.0, 3.0 and 0.5. It means the numbers of engine rotation per signal. For example the value 2.0 means the engine rotate 2 turns to output a signal. 7. Press RESET button to move in loop sequence from one to another value of the 4 values. Press MODE button to confirm the setting and go to wheel circumference setting screen. 8. In “cXXXX” display, “c” means “Circumference”, following 4 default digits; flashing digit is digit to be set. Follow the item 2 of button operation to finish the wheel circumference setting and jump to unit setting. 9. It displays KM/h or MPH, each press of RESET button converts unit; press MODE button to confirm unit setting and jump to odometer setting. 10. It displays “ODO & 00000Xkm”, the “X” is tested odometer in factory, follow item 2 to setting a desired odometer and jump to thermometer unit setting. The setting screen will disappear when the odometer is over 30km or your setting is over 30km and returned to main screen. 11. It displaysm ” , or oFF”, each press of RESET button converts , or oFF; press MODE button to confirm temperature setting and jump to temperature warning setting. 12. It displays ” XXX” and the selected unit. Follow the item 2 of button operation to finish the temperature warning setting and go to fuel sensor input resistance setting. 13. It displays “100r and fuel tank symbol”, follow the item 2 to select 100, 250, 510 Ohm or oFF and return to the main screen. The fuel meter bar will disappear if you select oFF mode.

Incoming search terms:

Kawasaki Ninja 250 FAQ

0

Filed Under (Kawasaki) by admin on 15-11-2010

download
Am I too small for this motorcycle? Duke – Sun May 14 17:38:31 2000 I’m only about 5’2″ and don’t have a problem, even though I can only touch the ground with the ends of my toes. Once you get a feel for the balance of the bike it’s not hard to keep everything upright. Only place I have trouble is pushing the bike backwards in a parking lot. Usually I just walk the bike (beside it) to where I can get on and get going. How does the EX500 compare to the EX250? Craig M. – Mon May 22 10:23:29 2000 I have both the EX250 and the EX500; both are Y2K models. The 250 is a screamer that performs well and can easily get me into trouble. My only complaints about the 250 are the excessive nose dive when getting on the front brake hard and the skittishness of the rear during high speed cornering. Both are easily corrected with suspension adjustments, I’ve just been too lazy to get the parts and do the work. A bit more wind protection would be great too. The 500 addresses these problems, the diving of the front end (to a degree); the rear’s skittishness and the wind protection. A plus for the 500 is the greater torque and power off the line; it pulls stronger (in my opinion) and will get you into illegal speed territory just a bit quicker than the 250. With greater weight, is has more stability in high speed and windy situations. Insurance is just about the same for both, with the 250 getting the nod for gas mileage. Service requirements are almost identical for both as well, being that they’re both parallel twins, the technology is the virtually the same. The downfalls of the 500: $2K more than the 250 (can do a lot to the 250 with that kind of money); buzzy mirrors, barely useful; heavier weight to have to push around the garage; lesser gas mileage (55-60 MPG; 250 pushes 70 MPG easily); engine is worse than a nervous dog shaking around at idle and at speed (here the 250 is far superior and much smoother). In my opinion, the 500 is a better suited for a larger rider, from a comfort standpoint. I feel I can stretch out a bit more on it than the 250 (I’m 5′ 9″, 160 lbs). The 250′s brakes are better tuned than the 500 and the shifter is much smoother. That may be due to the 3,500 mile difference between the two bikes. Bottom line, both bikes are great, the 250 is now my wife’s ride (mainly) and the 500′s mine (unless she steals the keys away). In time, I’ll make the adjustments to the 250; she doesn’t push it like I do.

Incoming search terms:

2008 KTM 250 SX-F 250 XC-F, XCF-W 250 EXC-F, EXC-F SIX DAYS INSTALLATION MANUAL

0

Filed Under (KTM) by admin on 22-10-2010

download
Hand brake lever The hand brake lever [1] is mounted on the handlebars on the right and actuates the front wheel brake. The adjusting screw [A] can be used to change the basic position of the hand brake lever (see “Maintenance”). 1 A Short circuit button The short circuit button [2] turns off the engine. When pressing this button, the ignition circuit is short-circuited. 2 Headlamp switch (XCF-W) In this model the headlamp is switched on with the pull switch [5] . 5 Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right
OPERATION INSTRUMENTS » ENGLISH 7 1 2 3 4 5 Starter button Pushing the red starter button [1] will actuate the E-starter. Emergency OFF switch (EXC-F Australia) The red emergency-OFF switch [2] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [3] will actuate the E-starter. Indicator lamps The green control lamp [4] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [5] lights up when the high beam is on. TEST All of the display segments briefly light up for the display function test. Electronic speedometer The display in the electronic speedometer is activated as soon as you press a button on the speedometer or an impulse is received from the wheel sensor. The display lights up when the engine is running. The display is cleared if no button is pressed for 1 minute or no impulse is received from the wheel sensor. The button is used to change between display modes. The + and – buttons are used to control various functions

Incoming search terms:

KTM Preload Adjuster frontfork Disassembly And assembling

0

Filed Under (KTM) by admin on 13-02-2011

download
Product Exploded View Disassembly & Assembling Workshop manual Preload Adjuster frontfork 5 Preload Adjuster Frontfork 03/2002 Screw the screw-cap to the right so that the spring washer is turning out of the screw-cap PA. Remove the spring washer. Pay attention to the assembling direction!!! Turn the plastic adjustment tube holder out of the screw-cap. 12_021 12_022 12_023Product Exploded View Disassembly & Assembling Workshop manual Preload Adjuster frontfork 6 Preload Adjuster Frontfork 03/2002 1. Remove the O-ring inside. Unscrew the air release plug. 12_024 12_025 12_026 2. Remove the O-ring.Product Exploded View Disassembly & Assembling Workshop manual Preload Adjuster frontfork 7 Preload Adjuster Frontfork 03/2002 Disassemble the adjusting knob from the screw-cap. Pay attention to the steel balls and spring!!! 12_027 12_028 12_029 Heat the steel nut. Unscrew the nut (size 32) clockwise .Product Exploded View Disassembly & Assembling Workshop manual Preload Adjuster frontfork 8 Preload Adjuster Frontfork 03/2002 The nut. Pay attention to the assembling direction!!! Remove the O-ring. 12_030 12_031 12_032 Push the holder rebound PA out of the screw-cap.Product Exploded View Disassembly & Assembling Workshop manual Preload Adjuster frontfork 9 Preload Adjuster Frontfork 03/2002 – springring – spring washer – O-rings – holder rebound adjustment tube – rebound adjusting knob with steel balls and spring – air release screw with O-ring – nut – holder rebound adjustment cpl. with O-ring – screw-cap PA

Incoming search terms:

HARLEY DAVIDSON PREMIUM SUSPENSION KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 09-03-2011

download
REMOVAL Front Fork Assembly 1. Refer to the XR model section of the service manual and remove the front forks. INSTALLATION Front Fork Assembly 1. Install front forks from kit to motorcycle according to service manual instructions but do not tighten the fork bracket pinch screws at this time. 2. See Figure 1. Measure the distance from the top of upper fork bracket to top of fork assembly. Both sides must be exactly the same and measure 0.388-0.468 inch (9.85- 11.89 mm) above the top fork bracket. Align the adjustment screws inline with the handlebars (see Figure 5). is06083a Figure 1. Fork Installation Height Measurement. NOTE If new pinch screws are not readily available, use a wire grinder wheel to remove all remaining lock patch from original pinch screws, wash screws in clean solvent and dry thoroughly. Apply two drops of LOCTITE® 262 to the first 1/4 in. (6.35 mm) of the end threads. 3. Install pinch screws to upper and lower fork brackets. 4. Verify fork tube installation measurement is 0.388-0.468 inch (9.85-11.89 mm). 5. Tighten pinch screws to 30-35 ft-lbs ( (40.7-47.5 Nm)) See Figure 2. The top edge of reflector should be 1-1/2 inches (38.10 mm) below the lower edge of the bottom fork clamp. 6. Remove the adhesive backing. Place reflector in position and press reflector firmly into place to activate the adhesive. Repeat for reflector on opposite fork. REMOVAL OEM Rear Shock Absorbers 1. Refer to the XR model section of the service manual and remove the rear shock absorbers. INSTALLATION Rear Shock Absorbers 1. See Figure 3. Install the rear shock absorbers according to service manual instructions. The shocks are installed with the external gas reservoir to the rear of the shock absorbers and the thick side of the grommet installed to the frame rail mounts. is06142 Figure 3. Install Thick Side Of Grommet To Frame Rail SUSPENSION ADJUSTMENTS Front Fork Suspension Adjustment Whenever a wheel is installed and before moving the motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00284a) Adjust both forks equally. Improper fork adjustment can lead to loss of control, which could result in death or serious injury. (00124c) Compression and rebound adjusting valves may be damaged if too much force is used at either end of the adjustment range. (00237a) NOTES Damping is set at the factory for the average solo rider under normal riding conditions. The rider may make adjustments to compensate for individual riding styles and varying road conditions. Evaluating and changing the rebound and compression damping is a very subjective process with many variables and should be approached carefully. The front and rear preload setting will need to be adjusted for the rider’s weight and cargo. This adjustment should be made before the motorcycle is ridden any distance and after changing the overall vehicle weight (adding saddlebags, etc.). If the preload adjustment is correct, and you have the rebound and compression damping set at the factory recommended points, the motorcycle should handle and ride properly. Changes in the load carried requires changes in the preload setting(s). Carrying less weight than was used for setting up the suspension requires decreasing the amount of preload. Increasing the load carried requires adding more preload. The following tools are needed to make suspension adjust- ments. • 5 mm hex key (front fork preload adjustment tool). • Spanner wrench with extension handle (shock absorber preload adjustment). • Screw driver (front fork damping adjustment). 1. Front fork preload adjustment: a. See Figure 4 and Table 1. Using the 5 mm hex key, turn the preload adjuster counterclockwise until it stops. This is the minimum preload setting. b. Turn the preload adjuster clockwise the recommended amount specified for the rider weight

Incoming search terms:

APRILIA SPORTCITY 125-200 Technical specifications

0

Filed Under (Aprilia) by admin on 07-11-2010

download
The engine and transmission assembly also acts as swing arm. Suspension is provided by two rear shock absorbers. Spring preload is adjustable for maximum efficiency under all load and road conditions. Rear wheel travel is 80 mm , more than enough to smooth out even the roughest surfaces. The SPORTCITY 250 i.e. is equipped with 15 inch wheels and large, high profile tubeless tyres (120/70 at the front and 130/80 at the rear). Rolling diameter is therefore equivalent to that of a 16 inch tyre but the ability to absorb shocks from rough road surfaces is far better, ensuring a superbly smooth ride. In conjunction with the excellent frame, this intelligent choice of tyres gives the SPORTCITY 250 i.e. excellent stability and the sort of intuitive feel that makes it a piece of cake to ride even for novices . The brakes are another of the strong points of the SPORTCITY 250 i.e. . The new system features triple discs for far shorter stopping distances and far greater active safety. Even inexperienced riders will have no trouble in pulling up well ahead of trouble. At 90 km/h the SPORTCITY 250 i.e. takes just 2.7 seconds to come to a full stop . The front brakes feature two 260 mm discs and floating calipers with two parallel pistons . The rear disc is a 220 mm unit with single piston caliper. Engine technology is another major plus point for the SPORTCITY 250 i.e. Its new electronic fuel injected engine is state of the art on the scooter scene . Powerful, flexible, and extremely low on emissions and consumption, this 250 cc single cylinder unit is perfect for the job in hand. Developing 22.5 HP at 8,000 rpm with 21 Nm of torque at 6,250 rpm, the engine delivers standard-setting performance . It also enables the Sportcity to function as a fun to ride sports scooter not only in town centres but on fast urban ring roads too. And the SPORTCITY 250 i.e. respects the environment wherever it goes, being one of the few scooters to conform to Euro 3 emission control standards. Finally, miserly fuel consumption and a generous 9 litre tank give the SPORTCITY 250 i.e. great autonomy . Engine Horizontal, single cylinder, 4 stroke. Forced liquid cooling with centrifugal pump. 4 valve head with overhead camshaft Fuel Unleaded petrol Bore and stroke 72 x 60 mm Displacement 244,29 cc Compression ratio 11:1 Maximum power 16.5 HP (22.5 kW) at 8,000 rpm Maximum torque 21 Nm at 6,250 rpm Fuel system Electronic fuel injection Ignition Electronic inductive discharge ignition with variable advance Starting Electric Alternator 300 W Lubrication Wet sump. Forced circulation with mechanical pump Gearbox Automatic torque converter Clutch Automatic centrifugal dry clutch Primary drive V belt Final drive Gearbox Frame Open cradle in high tensile strength steel Front suspension Hydraulic telescopic fork with 35 mm stanchions. Wheel travel 100 mm Rear suspension Engine unit acting as swinging arm. Double hydraulic shock absorber with adjustable preload. Wheel travel 80 mm Brakes Front: Twin ∅ 260 mm stainless steel discs. Twin piston floating callipers Rear: ∅ 220 mm stainless steel disc Wheels Light alloy Front: 2.75 x 15″ Rear: 3.00 x 15″ Tyres Tubeless. Front: 120 / 70 x 15″ Rear: 130 / 80 x 15″ Dimensions Maximum length: 1,985 mm Maximum width: 880 mm (at mirrors) Wheelbase: 1,360 mm Seat height; 815 mm Dry weight 148 kg Tank capacity 9 litres (reserve 1.5 litres) Colours Excalibur Grey, Shot Grey, Couture Blue, Moka Black Accessories 28 litre top box, 32 litre top box, 35 litre top box, large windshield, sports windshield, leg cover

Incoming search terms:

KTM 250/ 300/ 380 SX,MXC,EXC ENGINE REPAIR MANUAL

0

Filed Under (KTM) by admin on 12-11-2010

download
Repair manual KTM 250 / 300 / 380 Art No 3206004 -E 2-2C main jet jet needle jet needle air control screw idle adjusting screw idle jet throttle valve Idling range A Operation with closed throttle valve. This range is influenced by the position of the air control screw 1 and the idle adjusting screw 2 . Only make adjustments when the engine is hot. To this end, slightly increase the idling speed of the engine by means of the idle adjusting screw. Turning it clockwise produces a higher idling speed and turning the screw counterclockwise produces a lower idling speed. Create a round and stable engine speed using the air control screw (basic position of the air control screw = open by 1.5 turns). Then adjust to the normal idling speed by means of the idle adjusting screw. Opening up B Engine behavior when the throttle opens. The idle jet and the shape of the throttle valve influences this range. If, despite good idling-speed and part-throttle setting, the engine sputters and smokes when the throttle is fully opened and develops its full power not smoothly but suddenly at high engine speeds, the mixture to the carburetor will be too rich, the fuel level too high or the float needle is leaking. Part-throttle range C Operation with partly open throttle valve. This range is only influenced by the jet needle (shape and position). The optimum part-throttle setting is controlled by the idling setting in the lower range and by the main jet in the upper range. If the engine runs on a four-stroke cycle or with reduced power when it is accelerated with the throttle partly open, the jet needle must be lowered by one notch. If then the engine pings, especially when accelerating under full power at maximum engine revs, the jet needle should be raised. If these faults should occur at the lower end of the part throttle range at a four-stroke running, make the idling range leaner; if the engine pings, adjust the idling range richer. Full throttle range D Operation with the throttle fully open (flat out). This range is influenced by the main jet and the jet needle. If the porcelain of the new spark plug is found to have a very bright or white coating or if the engine rings, after a short distance of riding flat out, a larger main jet is required. If the porcelain is dark brown or black with soot the main jet must be replaced by a smaller one. mixture too rich: too much fuel in proportion to air mixture too lean: not enough fuel in proportion to air 1 2 OPERATING RANGES OF THE CARBURETOR 2-3C Carburetor adjustment Basic information on the original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambient temperature of approx. 20°C (68°F), mainly for off-road use and central European premium-grade fuel (ROZ 95 MOZ). Mixing ratio 2-stroke motor oil : super fuel 1:40 – 1:60. Basic information on a change of the carburetor setting Always start out from the original carburetor setting. Essential requirements are a clean air filter system, air-tight exhaust system and an intact carburetor. Experience has shown that adjusting the main jet, the idling jet and the jet needle is sufficient and that changes of other parts of the carburetor will not greatly affect engine performance. RULE OF THUMB:

Incoming search terms:

KYMCO MAXXER 300/ 250 MONGOOSE 300/ 250 SERVICE MANUAL

0

Filed Under (Kymco) by admin on 26-10-2010

download
apply or add designated greases and lubricants to the specified lubrication points. ÑAfter reassembly, check all parts for proper tightening and operation. ÑWhen two persons work together, pay attention to the mutual working safety. ÑDisconnect the battery negative (-) terminal before operation. ÑWhen using a spanner or other tools, make sure not to damage the motorcycle surface. ÑAfter operation, check all connecting points, fasteners, and lines for proper connection and installation. ÑWhen connecting the battery, the positive (+) terminal must be connected first. ÑAfter connection, apply grease to the battery terminals. ÑTerminal caps shall be installed securely. 1 . GENERAL INFORMATION 1-6 ATV 300/250 ÑIf the fuse is burned out, find the cause and repair it. Replace it with a new one according to the specified capacity. ÑAfter operation, terminal caps shall be installed securely. ÑWhen taking out the connector, the lock on the connector shall be released before operation. ÑHold the connector body when connecting or disconnecting it. ÑDo not pull the connector wire. ÑCheck if any connector terminal is bending, protruding or loose. Confirm Capacity 1 . GENERAL INFORMATION 1-7 ATV 300/250 ÑThe connector shall be inserted completely. ÑIf the double connector has a lock, lock it at the correct position. ÑCheck if there is any loose wire

Incoming search terms:

2006 KTM 250 SX-F 250 EXC RACING 400 EXC RACING 450 SX, XC, EXC RACING 525 SX, XC, EXC RACING, REPAIR MANUAL

0

Filed Under (KTM) by admin on 05-05-2012

download
Hot start lever (250 SX-F) If you pull the red hot start lever [1] during the starting procedure backward, a bore in the carburetor will be opened through which the engine may take in additional air. The result is a „lean” fuel-air mixture of the type needed for hot starts.
ENGLISH 7 OPERATION INSTRUMENTS » Headlamp switch (EXCUSA) In this model the headlamp is switched on with the pull switch [1] . Flasher switch The flasher switch is a separate unit and is mounted on the left portion of the handlebar. The wire harness is designed in a way that whenever you want to use your bike off-road, you can dismount the entire turn indicator system without affecting the function of the remaining electrical system. Flasher left Flasher right Starter button (EXC) Pushing the black starter button [2] will actuate the E-starter. Emergency OFF switch (EXC Australia) The red emergency-OFF switch [3] is arranged adjacent to the throttle grip. In this position, the E-starter is operational and the engine can be started. In this position, the E-starter and ignition circuits are interrupted.The E-starter cannot be actuated, and the engine will not start, not even if you attempt to start it with the kickstarter. Pushing the black starter button [4] will actuate the E-starter. 2 3 4 5 6 Indicator lamps The green control lamp [5] flashes in the same rhythm as the flashing indicator when the indicator is working. The blue control lamp [6] lights up when the high beam is on

Incoming search terms:

KTM 250/300/380 SX,MXC,EXC ENGINE REPAIR MANUAL

0

Filed Under (KTM) by admin on 19-11-2010

download
Carburetor adjustment Basic information on the original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambient temperature of approx. 20°C (68°F), mainly for off-road use and central European premium-grade fuel (ROZ 95 MOZ). Mixing ratio 2-stroke motor oil : super fuel 1:40 – 1:60. Basic information on a change of the carburetor setting Always start out from the original carburetor setting. Essential requirements are a clean air filter system, air-tight exhaust system and an intact carburetor. Experience has shown that adjusting the main jet, the idling jet and the jet needle is sufficient and that changes of other parts of the carburetor will not greatly affect engine performance. Checking the setting of the TVC system The function of the TVC system is checked with the engine running. This test checks the start of advance and the end of advance. -For this, remove the left control cover. -Connect a rev counter (either to the ignition cable or to the blue/white cable in the electronics box, depending on the rev counter design). -Start engine, accelerate gently and observe when the TVC system starts to advance (tooth segment creeps upwards) Bleeding of the hydraulic clutch -Take off cover together with rubber bellows. -At the slave cylinder of the clutch, remove the bleeder nipple 2 . It its place, mount the bleeder syringe 3 which is filled with SAE 10 hydraulic oil

Incoming search terms: