shafts mail

You search Auto repair manual PDF shafts mail, if there are search results will appear below. If search results do not exist, please search by others keyword.





Harley-Davidson Motorcycle Reverse Gear Installation Instructions

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
2.1 Obtain a small tube of Loctite® #262 (red) for use later. 2.2 Drain the transmission oil. 2.3 Remove the clutch adjustment cover (left side). 2.4 Remove rear exhaust header pipe (cross over exhaust pipe). 2.5 Remove the muffler support bracket. 2.6 Remove the clutch release cover (right side). 2.7 Remove clutch push rod and oil slinger. To be disassembled and modified later. 2.8 Remove the two nuts from the main (rear) and counter (front) transmission shafts. 2.9 Remove the transmission bearing housing (puller available from Champion Sidecars). To be replaced with new reverse gear transmission bearing housing (Trap Door). 2.10 Cover the exposed gears in the transmission with a cloth in preparation to cut the shifter fork shaft. 3 Install New Main and Countershaft Gears NOTE: Gears and Tapered Split Rings are factory matched sets. Do not mix!. 3.1 Locate the shifter fork rod, mark fork rod flush at transmission case and pull out 1/4″. Figure 1 Figure 2. Exposed Shoulders Mark shifter fork rod flush with case Remove Spacers Vehicle Transmission Counter Shaft Main Shaft Front of Motorcycle Figure 1
Reverse Gear Installation Instructions For EVO / 5 Speed and Twin Cam Harley-Davidson® Motorcycle Page 3 of 6 Revision 7 © 2007 Champion Motorcycle Accessories International, Inc. dba Champion Sidecars 11841 Monarch Street Garden Grove, CA 92841 (800) 875-0949 (714) 847-0949 www.championsidecars.com www.championtrikes.com Figure 6 CAUTION: Do not pull the shifter fork rod out of the transmission more than 1/4″. If you pull the shifter fork rod out too far, it will be difficult to realign it with the internal shifter fork. 3.2 Cut the shaft at the mark and push it back in. The shaft end MUST NOT stick out of the transmission case. If the shaft is in deeper, fill the hole with silicone to prevent the shaft from moving in and out. NOTE: Shifter fork is made of non-tempered metal and may be cut with a hacksaw or Dremel® cutting tool. 3.3 Important: Remove stock spacers from main and counter shafts. Spray with silicon remover (Brake-Clean) then, using supplied cleaning pad, clean shafts, new counter and main shaft gears and tapered lock rings (inside and outside) Figure 1 3.4 With motorcycle in neutral, pull both the shafts out and simultaneously push the OEM outermost gears in until seated completely to expose the shoulders of both shafts. The countershaft shoulder should be flush with the gear face. For the main shaft the gear would “hang over” the shoulder a small bit. Figure 2 3.5 Apply supplied Champion Super-Lock retaining compound to the inside and outside surfaces of the large gear tapered split ring, to the inside of the new countershaft gear (large gear) and to the transmission countershaft (the forward most shaft). 3.6 Install new countershaft gear to the transmission countershaft. Insert tapered split ring (tapered end first) into the countershaft gear. Install ring seat tool and spring to counter shaft and new countershaft gear. Torque ring seat tool to 40 ft-lb’s. Figures 3 and 4

Incoming search terms:

HARLEY-DAVIDSON 5 Speed Transmissions 1984 – 1999 EVO / 5 Speed & 1999 – 2006 Twin Cam Installation Instructions

0

Filed Under (Harley Davidson) by admin on 26-11-2010

download
Remove Original Parts From Vehicle. 2.1 Obtain a small tube of Loctite® #262 (red) for use later. 2.2 Drain the transmission oil. 2.3 Remove the clutch adjustment cover (left side). 2.4 Remove rear exhaust header pipe (cross over exhaust pipe). 2.5 Remove the muffler support bracket. 2.6 Remove the clutch release cover (right side). 2.7 Remove clutch push rod and oil slinger. To be disassembled and modified later. 2.8 Remove the two nuts from the main (rear) and counter (front) transmission shafts. 2.9 Remove the transmission bearing housing (puller available from Champion Sidecars). To be replaced with new reverse gear transmission bearing housing (Trap Door). 2.10 Cover the exposed gears in the transmission with a cloth in preparation to cut the shifter fork shaft. 3 Install New Main and Countershaft Gears NOTE: Gears and Tapered Split Rings are factory matched sets. Do not mix!. 3.1 Locate the shifter fork rod, mark fork rod flush at transmission case and pull out 1/4″. Figure 1 3.2 Cut the shaft at the mark and push it back in. The shaft end MUST NOT stick out of the transmission case. If the shaft is in deeper, fill the hole with silicone to prevent the shaft from moving in and out. NOTE: Shifter fork is made of non-tempered metal and may be cut with a hacksaw or Dremel® cutting tool. 3.3 Important: Remove stock spacers from main and counter shafts. Spray with silicon remover (Brake-Clean) then, using supplied cleaning pad, clean shafts, new counter and main shaft gears and tapered lock rings (inside and outside) Figure 1 3.4 With motorcycle in neutral, pull both the shafts out and simultaneously push the OEM outermost gears in until seated completely to expose the shoulders of both shafts. The countershaft shoulder should be flush with the gear face. For the main shaft the gear would “hang over” the shoulder a small bit. Figure 2 3.5 Apply supplied Champion Super-Lock retaining compound to the inside and outside surfaces of the large gear tapered split ring, to the inside of the new countershaft gear (large gear) and to the transmission countershaft (the forward most shaft). 3.6 Install new countershaft gear to the transmission countershaft. Insert tapered split ring (tapered end first) into the countershaft gear. Install ring seat tool and spring to counter shaft and new countershaft gear. Torque ring seat tool to 40 ft-lb’s. Figures 3 and 4

Incoming search terms:

Harley-Davidson Six Speed Transmissions FLH 2009 Up Champion Reverse Gear Installation Instructions

0

Filed Under (Harley Davidson) by admin on 17-02-2011

download
Preparation Remove Original Parts From Vehicle. 2.1 Purchase a small tube of Loctite #262 (red) for use later. 2.2 To torque the large gear: 2.2.1 Purchase Snap-On (or equivalent) filter tool. Part #: FWA62121. OR 2.2.2 Purchase Champion special tool – Part # RG-100-100 2.3 Drain the transmission oil. 2.4 Remove front and rear exhaust header pipe. 2.5 Remove the clutch release cover (right side). 2.6 Remove throw out bearing assembly. (to be reinstalled later without modification) 2.7 Remove the two nuts from the main and counter transmission shafts. WARNING : Do not attempt to push shafts into gearbox or remove the trap door – This can cause spacers inside the gearbox to be miss-aligned and lock up the gearbox when gears are installed and tightened. 2.8 Remove clutch push rod (to be replaced w/ Champion supplied rod) Note: For hydraulic clutch bikes, obtain Champion Part # RG-100-082, a longer push rod) Snap-On Part No: FWA62121 Snap-On Part No: FWA62121 Champion Part No: RG-100-100 Reverse Gear Installation Instructions Harley-Davidson Six Speed Transmission HD FLH 2009 Up Page 3 of 5 Revision 2 Boring Tool 3 Installation 3.1 Thoroughly clean threads of main and counter shafts using a silicon remover. 3.2 Apply the green thread locking compound (supplied) to main shaft threads and screw the small gear onto the main shaft. Figure 1 3.3 Install the supplied (ear)plug into the main shaft hole. To be removed later. 3.4 Install the supplied special tool to the small gear. Ensure the holes of the special tool align with the holes in the small gear. Figure 2 3.5 Install torque wrench to special tool and torque the small gear to 80 lb. ft. 3.6 Remove torque wrench from special tool. Do not remove special tool from small gear. 3.7 Using the supplied boring tool and the special tool as a guide, drill the main shaft through two holes of the special tool as shown. Stop when cutter contacts bearing race. Figure 3 3.8 Remove special tool, leaving main shaft plug in place, and thoroughly clean out the holes. Use care to ensure debris does not enter transmission. 3.9 Remove plug from main shaft hole. Figure 1 Figure 2 Figure 3 Note: To prevent gears from rotating during torque procedures, engage transmission into 1st gear and apply brakes Note: Frequently stop cutting and remove bit from hole to clean bit and vacuum debris from hole

Incoming search terms:

Harley-Davidson Six Speed Transmissions Reverse Gear Installation Manual

0

Filed Under (Harley Davidson) by admin on 16-02-2011

download
Remove Original Parts From Vehicle. 2.1 Purchase a small tube of Loctite #262 (red) for use later. 2.2 To torque the large gear: 2.2.1 Purchase Snap-On (or equivalent) filter tool. Part #: FWA62121. OR 2.2.2 Purchase Champion special tool – Part # RG-100-100 2.3 Drain the transmission oil. 2.4 Remove front and rear exhaust header pipe. 2.5 Remove the exhaust pipe support bracket. 2.6 Remove the clutch release cover (right side). 2.7 Remove throw out bearing assembly. (to be reinstalled later without modification) 2.8 Remove the two nuts from the main and counter transmission shafts. WARNING : Do not attempt to push shafts into gearbox or remove the trap door – This can cause spacers inside the gearbox to be miss-aligned and lock up the gearbox when gears are installed and tightened. 2.9 Remove clutch push rod (to be replaced w/ Champion supplied rod) Note: For hydraulic clutch bikes, obtain Champion Part # RG-100-082, a longer push rod) Installation 3.1 Reinstall exhaust pipe support bracket with the supplied two 5/16-18 x 1 3/4″ long hex head bolts and the ¼” thick spacer between engine and bracket. Figure 1 3.2 Thoroughly clean threads of main and counter shafts using a silicon remover. 3.3 Apply the green thread locking compound (supplied) to main shaft threads and screw the small gear onto the main shaft. Figure 2 3.4 Install the supplied plug into the main shaft hole. To be removed later. 3.5 Install the supplied special tool to the small gear. Ensure the holes of the special tool align with the holes in the small gear. Figure 3 3.6 Install torque wrench to special tool and torque the small gear to 80 lb. ft. 3.7 Remove torque wrench from special tool. Do not remove special tool from small gear

RACE TECH SUSPENSION SERVICE TOOLS

0

Filed Under (Tips and Review) by admin on 01-12-2010

download
SHOCK SEAL BULLET TOOL “Bullet Tools” make seal head installation onto shafts quick and easy. 35-8677 TSSB12512.5 x 10mm Shock Seal Bullet 35-8678 TSSB1414 x 12mm Shock Seal Bullet 35-8679 TSSB1616 x 12mm Shock Seal Bullet FORK CAP WRENCH 46/50MM Black Oxidized steel construction for superior strength. Multiple applications (46/50mm): Honda CR250 (97-00), Suzuki RM125/250 (96-00), and removes compression adjuster assembly on Suzuki RM125/250 (98-00). Sold each. 35-8670 TFCW4650 Fork Cap Wrench SHAFT HOLDING TOOL Holds fork damping rods, cartridges, shock shafts, etc. while servicing. (aluminum) 35-8672 TFSH10 Shaft Holding Tool 10, 12, 12.5, & 14mm (Dampning Rods) 35-8673 TFSH14 Shaft Holding Tool 14, 16, & 18mm (Shock Shafts) 35-8674 TFSH20 Shaft Holding Tool 20, 24, & 29mm (20 & 25mm Fork Cartridges) 35-8675 TFSH32 Shaft Holding Tool 32 & 35mm (28 & 32mm Fork Cartridges) ULTRA SLICK SEAL GREASE Race Tech Ultra-Slick Grease provides maximum lubrication and minimum friction for all seal and bushing needs. Available in 1 oz. container. 35-8682 Ultra Slick Seal Grease SHOCK SEAL HEAD SETTING TOOL Allows easy removal and installation of all 40 – 46mm integral shock seal head assemblies. 35-8676 TFSH32 Shock Seal Head Setting Tool SAG MASTER™ The Sag Master is a tool that makes measuring “Race Sag”a snap because you read it directly. No more subtracting! Also useful in determining proper spring rates and monitoring linkage and seal drag. Comes with complete instructions and, doubles as a tape measure. 35-8681 TSSM01 Sag Master Race Sag Setting Tool FORK SPRING COMPRESSOR TOOL This unique fork spring compressor is designed to work on most current sport bikes and road racers. It allows the spring to be compressed while the fork cap is removed from the rod. It can be used on or off the bike on most models. 35-8680 TFSC01 Fork Spring Compressor Tool

Toyota Camry TRANSMISSION REMOVAL & INSTALLATION – M/ T

0

Filed Under (Toyota Manuals) by admin on 21-06-2011

Download
1) Disconnect negative battery cable. Remove air cleaner case
with air intake hose. Remove cruise control actuator. Remove clutch
release cylinder with hose attached and secure aside.
2) Remove starter. Disconnect necessary ground straps,
electrical connections and control cables from transaxle. Remove upper
transaxle mounting bolts from cylinder block.
3) Raise and support vehicle. Remove front wheels. Remove
lower engine covers. Drain transaxle fluid. Remove axle shafts from
transaxle. See appropriate AXLE SHAFTS article in AXLE SHAFTS &
TRANSFER CASES section. Remove stabilizer bar mount and bushing from
crossmember

Toyota Camry, Celica, Corolla, MR2 (1995), Paseo, Pickup (1995), RAV4 (1996), Supra, Tacoma, Tercel, T100, 4Runner TRANSMISSION REMOVAL & INSTALLATION – M/ T

0

Filed Under (Toyota Manuals) by admin on 22-06-2011

Download
Disconnect negative battery cable. On 2.2L (5S-FE) models,
remove battery and cruise control actuator. On all models, remove air
cleaner case with air intake hose. Remove clutch release cylinder with
hose attached and secure aside.
2) Remove starter. Disconnect necessary ground straps,
electrical connections and control cables from transaxle. Remove upper
transaxle mounting bolts from cylinder block.
3) Raise and support vehicle. Remove front wheels. Remove
lower engine covers. Drain transaxle fluid. Remove axle shafts from
transaxle. See AXLE SHAFTS article in AXLE SHAFTS & TRANSFER CASES
section

2010 Toyota Motorsports/ TRD USA Contingency Award Program

0

Filed Under (Toyota Manuals) by admin on 29-09-2011

download
To enroll in the program, complete the registration form included in the enclosed material and mail, fax or e-mail it to TRD per the instructions at the bottom of the form. Contact personnel are listed on the attached 2010 Contingency Award Guidelines sheets. These people are available to assist you throughout the year. Parts Ordering: If you are planning to order Toyota parts during 2010 you must supply us with your Visa or Master Card credit card number at the time you register in the program. There is a line on the registration form for this number. See the attached Parts Ordering Guidelines for detailed information on how to order parts. TRD is looking forward to working with each of you, and we wish you a very successful year with your racing program

Incoming search terms:

1990 Harley Davidson ULTIMA 6 SPEED BUILDERS KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-04-2012

download
For 2000 & later models removal of approximately 1/4 of an inch off of the shifter arm bushing is likely required. Doing so will allow installation of the retaining clip & washer onto the shifter arm. It is good practice to double check how much material should be removed before cutting the bushing. See fig. 1 & 2 Install supplied Main drive gear bearings & countershaft needle bearings using special tool # 97-164 NOTE: Lightly coat bearings with assembly lube or gear oil for easier installation. Install supplied Main drive gear retaining clip & verify that it is fully seated and cannot come out. Do not re-use old bearings or retaining clip. Install supplied Main drive gear into bearings using special tool # 97-166 See fig. 3 Install supplied trap door gasket & verify that it is on correctly. Install supplied 6 speed gear set making sure to align the countershaft with the needle bearing assembly. Slowly slide in gear set until the mainshaft & countershaft will not slide in any further. Lightly tapping on the trap door (while verifying that there is no interference) with a soft blow hammer will then fully seat the shafts & trap door. See fig. 4 Once gear set is installed use the supplied 5/16-18×1-1/2 & 1/4-20×1-1/2 bolts to secure the trap door. Torque the 5/16 bolts to 15 ft-lbs w/ red loctite (high strength) Torque the 1/4 bolts to 9 ft-lbs w/ red loctite (high strength) See fig. 5 FIG. 1 FIG. 2 FIG. 3 FIG. 4 FIG. 5 2 FIG. 6 At this time check to make sure all gears rotate freely & that all slider gears slide with no interference. Lightly lube & install supplied quad seal onto main drive gear. See fig. 6 Install Main seal using special tool # 97-164. See fig. 7 Install original spacer onto mainshaft. NOTE: Beveled side goes in towards quad seal. See fig. 8 Install supplied transmission drain plug & supplied speedo sensor plug with gasket. Install supplied shifter forks onto appropriate slider gears. See fig. 9 Lightly lube & install supplied shift fork shafts. NOTE: Short shaft is installed from the right side with the threaded hole facing out. Long shaft is installed from the left side & should not protrude from the right side of case. See fig. 10 Install supplied shift fork shaft allen head plugs. (Use red loctite to prevent movement of plug & to aid in sealing)

YAMAHA ROADSTAR/ WARRIOR ADJUSTABLE REAR LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 16-01-2012

download
Secure motorcycle to a bike lift and raise the motorcycle. Rear wheel should remain barely resting on the ground. 2. See diagram on page 2 for references made in parentheses, for example (#5). 3. Remove the nut from the rear suspension bolt (#5) at the bottom of the shock (#7). You may need to remove your exhaust and rear horn to access the nut and bolt. 4. Remove this suspension bolt (#5) from the non-exhaust side of the bike. You may need to raise or lower the bike to ease the tension on the bolt in order for it to come out. 5. Next remove the nut (#4) and bolt connecting the relay arm (#3) to the swingarm. From here remove the entire shock assembly and relay arm from the bike. For ease of re-installing the relay arm (Step 8) and shock be sure to take precautions that in removing the assembly, you can put it back the same way you took it off. Flipping of the relay arm can cause serious damage to the lowering kit and surrounding components. 6. Remove the two suspension arms from the relay arm(#3) and shock(#7). Compare stock arm to length of lowering arm you are about to install. Make sure the length of the lowering arm matches the link of the stock arm. To set how much you want to lower the bike, lengthen the lowering arms. Every 1/4″ longer than stock is approximately 1″ of drop. Do not lower the bike more than 2″ for safety reasons. To adjust, unscrew the large hex shaft from the threaded rods. Make sure to adjust length equally on both shafts. Be sure to tighten all jam nuts once desired lowering position is set. 7. Re-assemble the lowering arms to the top of the shock (#7) using the supplied collar, nut, and bolt. The stock collar (#6), the one in the eyelet at the top of the shock (#7), will need to be removed as it is too long. (This is because the heims are thicker than the stock arms) Do not tighten the nut, or re-install into the frame yet. 8. Re-install the relay arm (#3) to the swingarm. The large hex shafts go to the rear of the bike. This is where it

Incoming search terms:

Incoming search terms: