shovelhead primary sprocket removal

You search Auto repair manual PDF shovelhead primary sprocket removal, if there are search results will appear below. If search results do not exist, please search by others keyword.



  shovelhead primary sprocket removal Direct Download speed 5282 Kb/s

  shovelhead primary sprocket removal Full Version speed 6162 Kb/s



HARLEY DAVIDSON HYBRID CAM PLATE AND HIGH FLOW OIL PUMP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Refer to the service manual and follow the instructions to remove the seat and disconnect the battery cables, negative (-) cable first. Retain all seat mounting hardware. Gasoline can drain from the carburetor fuel line when disconnected from fuel valve fitting. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00256a) NOTES Installing this kit requires removal and installation of the cam support plate. Refer to the service manual for instructions with the following exception pertaining to cam compartment compo- nents: The crank and primary cam sprocket flange bolts are specially hardened, and the flat washers are of a special diameter and have ground surfaces. Use ONLY the parts provided in the Drive Gear Retention Kit (H-D Part Number 25533-99A, sold separately) when installing this kit. -J04804 1 of 7
The cr ank sprocket flange bolts and pr imary cam sproc ket flange bolts ARE NOT interchangeable. 2. Refer to the service manual to remove and discard the crank sprocket flange bolts and primary cam sprocket flange bolts and washers. 3. For 1999 models only: Refer to the service manual to remove and discard the currently installed cam drive sprocket. 4. Refer to the service manual to remove and disassemble the cams from the support plate and oil pump. Discard the support plate and oil pump. 5. For 1999 – 2000 Dyna, 2000 Softail, 1999 – 2000 Touring, and 2001 EFI Touring models only: Inspect the cams, chain, sprockets and chain tensioners for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. For 2001 – 2005 Dyna, 2001 – 2006 Softail, 2002 – 2006 Touring, and 2001 carbureted Touring models only: Inspect the cams and secondary cam chain for wear, and replace as needed. Refer to the service manual for inspection and replacement procedures. The primary cam chain, primary sprockets and both tensioners will be replaced by new components from the kit. For ALL models and years: Discard the guide, as it will not be used. INSTALLATION 1. ALL models: See Figure 1. Obtain the new Rear Cam Roller Bearing Kit (H-D Part Number 8983) from inside the Cam Service Kit (H-D Part Number 17045-99C, purchased separately), and install as indicated in Step 2. NOTE See Figure 2. If not enough of the splined shaft is exposed to install the sprocket, omit the spacer (4) and proceed to Step 2e. When the bearing inner race is started onto the machined area, remove the flange bolt (5), flat washer (6) and sprocket, then assemble using the spacer (4). Repeat Step 2e to fully install bearing inner race. To center thrust washer, be sure o-ring is installed in relief groove. Damage to bearing cage and engine can occur if thrust washer is not centered. (00473b) 2. See Figure 1. Install the O-ring (5), thrust washer (4) and bearing inner race (3) onto the rear camshaft as follows: a. See Figure 2. To properly locate the thrust washer (2), install the O-ring (3) in the grinding relief groove on the splined end of the rear camshaft between the machined area and the secondary cam sprocket.

Incoming search terms:

Harley-Davidson BAKER COMPENSATING SPROCKET INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 19-04-2012

download
1) Remove the primary chain case cover. Refer to your Factory Service Manual for this procedure. 2) Remove the compensating sprocket nut with a 1-1/2″ socket. A ½” impact gun is best for this task. *) Remove the 1-3/16″ clutch nut. This is a left handed nut so loosen it by turning it in the clockwise direction (as viewed from the left side of the motorcycle). 4) With one hand on the compensating sprocket and one on the clutch assembly, remove the primary drive assembly (compensating sprocket, primary chain, tensioner assembly, and clutch as shown in figure a and set it on a clean surface. 5) Flip the adjuster shoe bracket on the chain tensioner assembly. figure b shows the stock orientation of the adjuster show and bracket. Figure C shows the adjuster show bracket flipped 180°. To flip the shoe bracket, remove the two ¼-28×2 bolts that hold the bracket assembly together. This will allow you to separate the chain tensioner assembly components from the primary chain. Flip the bracket around as shown in figure c . PAGE 4 Figure B Figure A BAKER COMPENSATING SPROCKET INSTALLATION INSTRUCTIONS 6) install the new compensating sprocket, chain, and clutch onto the motor sprocket shaft and the transmission input shaft. The flipped chain tensioner assembly (as shown in figure c ) is not ‘captured’ on the primary chain like the stock configuration. Loosely install the chain tensioner assembly onto the anchor plate bolt. Tighten the compensating sprocket nut to 157+ 7 ft-lbs and the clutch hub nut to 75+ 5 ft-lbs using red Loctite on the threads.

Incoming search terms:

HARLEY DAVIDSON CHROME BELT SPROCKET COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
Installation 1. Remove rear wheel. Refer to the applicable Service Manual for the proper removal procedure. 2. Remove bolts and washers from sprocket. •If you intend to install Acorn Nut and Stud Kit (Part No. 91734-85), refer to that Instruction Sheet at this time (please note that this Acorn Nut and Stud Kit does not fit Sportster (XL) models). •If you do not intend to install Acorn Nut and Stud Kit (Part No. 91734-85), retain bolts and washers for reassembly. Proceed to Step 3. 3. Position sprocket cover so that its mounting holes align with the holes in the sprocket. NOTE There is only one position which allows each hole in the cover to align with a hole in the sprocket. If replacement bolts, washers, or nuts are required, use only genuine Harley-Davidson parts specified for your particular model. Aftermarket fasteners can adversely affect performance, which could result in death or serious injury. NOTE • See Harley-Davidson service manual for proper torque val- ues; •Aftermarket fasteners may not have the specific property requirements to perform properly. 4. Install bolts with washers through holes in sprocket cover and sprocket, and into threaded holes in wheel hub. Depending on the tensile strength grade of the bolts in your particular application, tighten bolts in a crosswise pattern to one of the torque values listed in the following table: 5. Refer to the applicable Service Manual for the proper procedure and perform the following: •Install axle. •Align belt. •Adjust belt tension. •Tighten rear axle nut to 60 – 65 ft-lbs torque. 6. Check sprocket for radial runout (eccentricity). If runout is visible, mark outer edge of sprocket at the location of runout. Loosen sprocket bolts and tap the marked location with a rubber mallet. Tighten sprocket bolts in a crosswise pattern to the applicable torque specified in Step 4.

Incoming search terms:

HARLEY DAVIDSON CHROME SPROCKET HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-02-2011

download
INSTALLATION For 1991 through 1996 XL with Laced Wheels For 1993 through 1996 Softail with Laced Wheels For 1993 through 1997 Dyna with Laced Wheels 1. Remove the rear wheel. Refer to REAR WHEEL REMOVAL in the Service Manual. 2. Remove all stock sprocket mounting screws, washers and locknuts. 3. Place a new chrome washer onto the threads of each new chrome screw from the kit. Install the sprocket onto the wheel. 4. See Figure 1. Obtain new original equipment locknuts and install on the screws. See Figure 2. Tighten all screws in the sequence shown to 45-55 ft-lbs (61-75 Nm). 5. Install the rear wheel. See REAR WHEEL INSTALLATION in the service manual. Verify the correct axle alignment and check belt deflection per service manual instructions INSTALLATION For 1997 and Later XL with Laced Wheels For 1997 through 1999 Softail with Laced Wheels For 1998 through 1999 Dyna with Laced Wheels For ALL Models with Cast Wheels 1. Remove the rear wheel. Refer to REAR WHEEL REMOVAL in the Service Manual. 2. Remove all stock sprocket mounting screws and washers. 3. Place a new chrome washer onto the threads of each new chrome screw from the kit. Apply 2-3 drops of Loctite 262 (red) to the screw threads, and install the sprocket onto the wheel. Tighten all sprocket screws finger-tight. 4. See Figure 3. Tighten the bolts in the sequence shown to 23 ft-lbs (31.2 Nm). NOTE If 23 ft-lbs (31.2 Nm) is reached before screw is fully seated, remove screw and examine screw and wheel for thread damage. Replace screw or wheel if threads are damaged. 5. After all screws have been tightened to 23 ft-lbs (31.2 Nm), mark a straight line, with a grease pencil, on all sprocket screw heads continuing the line over onto the sprocket. 1 4 2 5 3 30 is04009 Figure 3. Tightening Sequence (Later Laced Wheels and All Cast Wheels) 6. Mark a second line at 30° clockwise from the lines on the sprocket at each screw. NOTE For best results, use Snap-on Torque Angle Gauge TA360 or equivalent. 7. Using the marks as a guide, and using the tightening sequence shown in Figure 3+, turn each screw an additional 1/12 turn or 30° clockwise. 8. Install the rear wheel. See REAR WHEEL INSTALLATION in the service manual. Verify the correct axle alignment and check belt deflection per service manual instructions

Incoming search terms:

HARLEY DAVIDSON CHROME INNER PRIMARY HOUSING INSTALLATION INSTRUCTION

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
Kit Contents Table 1. Kit Contents Part Number Description (Quantity) Not sold separately Chrome Inner Primary Housing 786A Sealing fastener (5) INSTALLATION NOTES Whenever the sealing fasteners are loosened or removed, they must be replaced. Always replace using Harley-Davidson® Original Equipment sealing fasteners part 786A. Do not use part 786. The primary housing included in this kit installs in the same manner as the stock inner primary housing with the following exception: Use the five sealing fasteners included with this kit. Install and tighten fasteners to the torque specified below. For 2006 Dyna model motorcycles: Remove dowel pins from the chrome inner primary housing before attempting installation. Using a pair of pliers or vice grips, remove the dowel pins by carefully twisting and pulling on the pins. Be careful not to scratch or mar the chrome or sealing surfaces of the chrome inner primary housing. Remove the chain tensioner anchor plate, bolt and screws from the stock inner primary housing after it has been removed, then install it on the chrome inner primary housing. See the appropriate Service Manual for the proper tightening procedure, and torque specifications. 1. See the Drive section of the appropriate Service Manual, and remove the stock inner primary housing. Clean the internal threads in the crankcase and transmission case where the sealing fasteners were removed using a wire brush. Install the chrome inner primary housing as indicated below. Replace the five stock sealing fasteners with the five bolts included in this kit. Put a light coat of primary oil under the head of the sealing fasteners and then tighten to 23-25 ft- lbs (31-34 Nm)

Incoming search terms:

HARLEY DAVIDSON SOFTAIL 6 SPEED TRANSMISSION – COMPLETE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-04-2011

download
Removal of Original Transmission 1. Position motorcycle on a suitable lift. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. 3. Refer to the TRANSMISSION CASE REMOVAL in the Service Manual and follow the instructions given to remove the components with the following steps. 4. Refer to PRIMARY CHAINCASE COVER REMOVAL in the Service Manual and follow the instructions given to remove the primary chaincase cover. Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) 5. See the PRIMARY CHAIN and COMPENSATING SPROCKET REMOVAL in the Service Manual and use the instructions given to remove the primary drive assem- bly. 6. Refer to the STARTER REMOVAL in the Service Manual and remove the the starter. 7. See the VEHICLE SPEED SENSOR section and unplug the vehicle speedometer sensor connection and remove the mounting bolt. Lift sensor from the transmission case and set aside for later re-installation. 8. Refer to NEUTRAL SWITCH and disconnect the connectors from the neutral switch. 9. Refer to PRIMARY CHAINCASE in the Service Manual and follow the instructions given to remove the primary chaincase housing. 10. Refer to EXHAUST SYSTEM in the Service Manual and remove the exhaust. 11. See the REAR WHEEL REMOVAL and loosen but, do not remove rear axle to relieve drive belt tension and remove the belt from the sprocket from the transmission. 12. Refer to OIL TANK REMOVAL in the Service Manual and follow the instructions given to drain, remove the oil tank and detach the vent, feed and return lines. 13. Refer to CLUTCH CONTROL in the Service Manual and follow the instructions given to remove the clutch cover and disconnect the clutch cable end from the cover. Set the cable aside for later re-installation

Incoming search terms:

Harley-Davidson Softail Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 02-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the fasteners that secure the seat. Remove seat. 6. Disconnect negative Battery Terminal. 7. Remove the Saddle Bags. And their hardware. If equipped. 8. Loosen Muffler Clamp on both Mufflers and other attaching hardware. Remove and discard both Mufflers. 9. Loosen the 4 exhaust stud nuts and save. Remove and discard head pipes and exhaust gaskets. 10. Disconnect the Rear Lamp Wiring Harness. 11. Remove any fasteners from Electrical Box. 12. Remove and discard Rear Fender, Fender Support and fasteners. NOTE: 2008-Current various models. Remove ECM from Fender and save nuts. 13. Drain all Brake Fluid from the Rear Brake System. 14. Un-clamp Rear Brake Line from the frame and Rear Fork. 15. Remove and discard both Banjo Bolts and Crush Washers from the Rear Brake Caliper and the Rear Brake Master Cylinder. 16. Remove Brake Light Switch from the Brake line, Save for reassembly. 17. Remove the Torx screw from the Brake Line bracket, Save the Torx screw for reassembly. 18. Remove and Discard Brake Line. 19. If Lower Controls option. Remove and Discard right and left floorboards/foot pegs, brake pedal, shifter, and shift linkage. Remove and Discard Passenger Foot pegs or Floorboards and their mounts. Then skip to step 24. 20. If Lower Controls Not purchased. Continue. 21. Remove acorn nut from Shift Linkage. 22. Remove 3 fasteners from Drivers Floorboard and remove. 23. Remove and discard Jiffy Stand. 24. Remove the Primary Cover by first removing the top and rear inspection cover screws. 25. Continue by removing remaining fasteners. 14 total. 26. Remove and discard Primary Cover Gasket. 27. Clean residual gasket material from both surfaces. 28. Loosen the Top Center Nut on the Primary Chain Adjuster. Lower the Primary Chain Adjuster until it rests flat on the Inner Primary Cover. 29. Remove the Clutch Lifter Retaining Ring from the Clutch Basket. Remove Clutch Lifter Assembly. 30. Using the Primary Drive Locking Tool. Loosen the Compensating Sprocket Nut. 31. Using the Primary Drive Locking Tool. Loosen the Clutch Hub Main shaft Nut. WARNING: This nut is LEFT HAND threaded. 32. Remove the Primary Drive Locking Tool, Compensating Sprocket Nut, and Clutch Hub Main shaft Nut. 33. Remove the Sprocket cover and Sliding Cam from the Crank Shaft Extension. 34. Remove the Clutch Assembly, Primary Chain, Compensating Sprocket, and Crank Shaft Extension in one assembly.

HARLEY DAVIDSON 45-AMP. UPGRADE ALTERNATOR ROTOR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
This 45-amp Rotor Kit is designed for installation on 1999 and later FLHT, FLHTC, FLHR, FLHRI, FLHRCI and FLTR Model Motorcycles. Existing Rotor Removal 1. Remove seat and disconnect battery terminals, negative cable first. 2. Follow instructions in applicable Service Manual and remove the primary chaincase cover. Remove the clutch, primary chain, compensating sprocket and shaft extension as a single assembly. 3. Remove the alternator rotor spacer, if present. Installation The laminated high-output rotor in this kit contains magnets that are considerably more powerful than those used in most previous rotors. The ROTOR REMOVER/INSTALLER and SHAFT PROTECTOR SLEEVE (HD-41771) must be used to prevent parts damage during rotor removal and installation. 1. See Figure 1. Verify threads are clean and thread the Shaft Protector and Rotor Remover/Installer, if removed. NOTE The Shaft Protector Sleeve not only protects the threads from the splines of the rotor, but acts as a guide to ensure that the rotor is properly centered. 2. Turn thumbscrews of Rotor Remover/Installer into threaded holes in rotor face. CAUTION 1 WARNING 1 WARNING 1 WARNING Kit Number 29999-97B Figure 1. Install Shaft Protector and Rotor Installer Engine Sprocket Shaft 1. Make Sure Threads are Clean 2. Install shaft protector sleeve. Shaft protector sleeve 3. Install Rotor Remover/Installer i04153 Handle Thumbscrew Forcing screw . Center ball on forcing screw in recess at end of engine sprocket shaft. Rotate the handle of the tool in a counterclockwise direction to ease rotor into position over stator. 4. Loosen thumbscrews and remove Rotor Remover/Installer. Remove Shaft Protector Sleeve. 5. Install the shaft extension on engine sprocket shaft. No alternator rotor spacer is necessary). 6. Follow instructions in applicable Service Manual and install the clutch assembly, primary chain and shaft extension as a single assembly. 7. Apply two drops of Red LOCTITE®262 to threads of clutch nut and engine sprocket nut. Tighten nuts as fol- lows: Clutch nut- (left hand threads), 70-80 ft-lbs (94.9-105.5 Nm) Engine sprocket nut- 150-165 ft-lbs (203-223 Nm). 8. Follow instructions in Service Manual and install the Primary Chaincase Cover using new gasket from kit, if necessary.

Incoming search terms:

HARLEY DAVIDSON DYNA SPROCKET KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
1991-1992 Dyna models: Screw (5) 3739A 1993-1995 FXDL, 1995 FXD and FXDS, all 1997-1999 Dyna models: Screw (5) 3730A 1993-1995 FXDWG and all 1996 Dyna models: Screw (5) 3769 1991-2005 Dyna models: Washer (5) 6516HW 2000-2006 Dyna models: Screw, with lock patch (5) 3737A 2006 Dyna models: Screw, with lock patch (5) 3873 2007 and later Dyna models: Screw, with lock patch (5) 3109 The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Do not re-use sprocket mounting screws. Re-using sprocket mounting screws can result in torque loss and damage to the sprocket and/or belt assembly. (00480b) Kit Contents There are no Service Parts available with this kit. INSTALLATION NOTES The cotter pin or spring clip for the rear axle nut must be replaced during assembly and is available for purchase from a Harley-Davidson dealer. The five sprocket mounting screws must be replaced when replacing the sprocket. Remove existing sprocket according to service manual instructions. Remove all residual threadlocking agent from fastener holes using an appropriate thread chasing device and compressed air.

Incoming search terms:

HARLEY DAVIDSON DYNA STATOR AND ROTOR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative battery cable. See BATTERY MAINTENANCE in Service Manual. 2. Remove primary cover, primary drive, and clutch. See DRIVE COMPONENTS in Service Manual. 3. Remove primary chaincase according to the instructions in the Service Manual. 4. See Figure 2. Pull off the alternator rotor (1) using two bolts inserted through the holes in the rotor face. 5. Remove the two T-27 TORX screws (2). 6. Unplug the voltage regulator and remove the stator (3). See VOLTAGE REGULATOR in Service Manual. 7. Disassemble connector [46B] (A). See DEUTSCH ELECTRICAL CONNECTORS in Service Manual. NOTE Contact cleaner, alcohol, or glass cleaner sprayed on rubber grommet (B) will provide lubrication when pulling it through crankcase hole. 8. Move grommet (3) to one side and spray contact cleaner into gap. Repeat for other side. Pull rubber grommet (B) through crankcase hole. 9. Pull wires through crankcase hole. INSTALLATION 1. Insert wires through crankcase hole. 2. See Figure 1. Push rubber grommet (B) through crankcase hole. If necessary, apply the same lubricant used during removal. 3. Insert wires into connector [46B] (A). 4. Mate connector [46]. See VOLTAGE REGULATOR in Service Manual. is03776 Figure 1. Voltage Regulator 5. See Figure 2. Install the stator (3) on the crankcase and fasten in place using new TORX screws (2). Tighten to 55-75 in-lbs (6.2-8.4 Nm). 6. Install the rotor (1) on the sprocket shaft. 7. Apply Loctite Threadlocker 262 (red) to sprocket nut threads. Tighten sprocket nut to 150-165 ft-lbs (203.4- 223.7 Nm). 8. Install primary chaincase according to the instructions in the Service Manual. 9. Install clutch, primary drive, and primary cover. See DRIVE COMPONENTS in Service Manual. 10. Connect negative battery cable. See BATTERY MAINTENANCE in Service Manual

Incoming search terms: