shovelhead rocker box removal

You search Auto repair manual PDF shovelhead rocker box removal, if there are search results will appear below. If search results do not exist, please search by others keyword.



  shovelhead rocker box removal Direct Download speed 5282 Kb/s

  shovelhead rocker box removal Full Version speed 6162 Kb/s



Triumph Bonneville America And Speedmaster The Freak Installation Instructions and Parts List

0

Filed Under (Triumph) by admin on 29-10-2010

download
INSTALLATION In order to install The Freak, the factory air-box must be removed. Because of it’s design, the factory air-box is not an item that is easily removed. There are several parts that must be removed in order to get the air-box out of the bike in one piece. We recommend using the following method to remove your air box without having to cut it into smaller pieces in order to get it out of the frame. 1. PARTS REMOVAL In order to gain access to the air-box, it is necessary to remove certain parts of the motorcycle to gain access to the air-box area of the frame. Removing the following parts should be the first steps you take. A. Seats – Remove both seats starting with the passenger pillion, if applicable. B. Side cover and grommets – Remove the plastic side cover on the right side (throttle side) of your motorcycle. This is the faux oil-tank cover that has the name of your bike on it. Underneath the side cover there are three rubber grommets (1 on the frame tab, and two on the air-box) that support the side cover. Remove the two that are on the air-box and leave the one on the frame. You will attach the two that you removed to the right side bracket in Section 4C . C. Faux air filter covers – On the right side of the bike, remove the chrome faux air filter covers, by removing the one allen head screw that holds it onto the air-box. On the left hand side (clutch side) remove the faux air filter cover in the same manner, you removed the one on the right. D. Plastic shrouds – on the left side, remove the black plastic air-box shroud, by removing the two allen head screws holding it in place. Then remove the plastic shroud covering your fuse box (this is the piece that surrounds your ignition terminal next to the battery). E. Battery – Remove the battery by unscrewing the torx-head bolt that holds the chrome bracket in place. Remove the chrome bracket and the black plastic cap. Tilt the battery out of the box with the top towards you. Disconnect both battery terminal connectors, negative (-) terminal first. Remove the battery. F. Battery box – Remove the two bolts that hold the battery box to the frame. Pull the battery box out as far as you can, then remove the the ignition terminal from the battery box, by removing the two allen screws that hold it in place from the back. Next, remove the fuse box from the battery box, by pushing it out from the back. It is not necessary to disconnect any of the wiring going to the fuse box, or the ignition terminal. G. Rear fender – Remove the rear fender, by first disconnecting the taillight wires. Follow the wires from the tail light assembly on the inside of the rear fender (left side) towards the front of the bike until you come to the box connector. Disconnect the tail light wires at this connector, being careful not to break it. Once the wiring is disconnected, remove the 6 bolts that hold it to the struts. Have someone hold the fender for you while you are removing all of the bolts so that it does not drop once the bolts are removed. Slide the fender out the rear of the bike. 2. PREPARE THE MOTORCYCLE FOR AIR-BOX REMOVAL To remove the factory air-box without damaging it, it is necessary to lift the bike. We recommend the use of a multi-position ATV/motorcycle jack with a minimum lift height of 10″. A. Setting up the lift – Place the lift under your bike and secure your bike to the lift according to the lift manufacturer’s instructions. B. Raise slightly – Lift the motorcycle to the point where the rear springs are without tension, but NOT to where the rear tire is off the ground. C. Remove the rear springs – Take off each of the rear springs by removing the the two bolts on each spring. Once all the bolts are removed gently pull the springs out off of the studs. If they do not pull off easily, you can raise or lower the bike slightly with the lift to ease tension on the spring. Remember, you should not have the rear tire off the ground at this point. The bike should only be raised enough to relax the tension in the springs. D. Remove the mufflers – Remove the mufflers by loosening the clamp at the exhaust header, and by removing the rear foot peg hangers. If the mufflers are not removed, they can become damaged by the axles in Section 2H . E. Disconnect the carburetors – With a small flathead screwdriver, pull the retainer springs out of the channel of the carburetor intake tubes (the two large black tubes coming from the air box into the back of each carburetor), and simply push them towards the air box off of the carbs

Incoming search terms:

HARLEY DAVIDSON LOCKING GLOVE BOX DOOR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
INSTALLATION 1. Unsnap the original equipment (O.E.) left-side glove box door, and unfasten the tether by bringing the aglet end (see Figure 1, B) out through the retaining hole. Always wear proper eye protection when drilling or grinding. Flying debris could cause serious eye injury. (00402e) 2. Using an 3/16 inch (5 mm) bit positioned in the center of each snap, drill out the four plastic snaps surrounding the glove box opening. NOTE The glove box door, hinge and frame assemblies are side- specific. The assemblies install so that the tether retaining hole (C) in the door frame is to the inboard side. 3. Obtain the new left-side glove box door, hinge and frame assembly (1), a lock (2) and a tether assembly (8) from the kit. Remove the nut (3) from the lock. 4. Insert the lock through the hole in the glove box door as shown. Assemble the tether over the lock threads with the tab (A) on the inboard side of the lock, same as the retaining hole in the door frame. Tighten securely. 5. Open the left-side door, and position the door assembly at the glove box opening, lining up the holes. 6. Insert a screw (9) through each of the holes in the door frame and glove box. Install a hex nut with washer (10) onto the threads of each screw. Tighten finger-tight. NOTE Ambient temperature should be at least 60° F (16° C) for proper adhesion of the gaskets to the glove box door frame. 7. Clean the glove box door frame with a mixture of 50 to 70% isopropyl alcohol and 30 to 50% distilled water. Allow to dry thoroughly. NOTE The glove box gaskets are side-specific. With the paper backing facing the door frame, the oblong hole at the top of the gasket is to the outboard side. 8. Obtain the left-side gasket (6) and a hinge gasket (7) from the kit. Install the gaskets to the glove box door frame. a. The gasket liner on the large gasket is split to aid alignment. Peel one half of the liner from the adhesive backing of the left-side gasket. b. Using the frame edges and screw heads as a guide, carefully position the gasket to the glove box door frame and press firmly into place. c. Peel the remaining half of the liner from the gasket backing, and carefully position the rest of the gasket to the door frame. Press firmly into place. d. Apply steady pressure for a few seconds at all areas of the gasket to verify proper adhesion. e. Peel the liner from the hinge gasket. f. Carefully position the gasket to the door frame above the hinge, and press firmly into place.

Indian Rocker Arm End Play Rear Cylinder/ Front Cylinder Installation

0

Filed Under (Indian) by admin on 12-11-2010

download
Rear Cylinder 1Rotate the engine so that the rear piston is at Top Dead Center (TDC), compression stroke, so no load is on the valves. 2Using a 3/16″ allen wrench, remove the four screws securing the rear cylinder rocker cover. 3Remove the cover and inspect both O-ring seals. Discard if damaged or worn. 4Push both rocker arms towards the valve end support bracket (A) and using a feeler gauge check the gap between the rocker arms and the pushrod end support bracket (B). NOTE: The Rocker arm end play specification should be between 0.003″ to 0.012″. 5 Compare the measurement to the specification an determine whether adjustment is necessary. If the end play is within specification, adjustment will not be required. Refit the rocker cover (instructions 14 to 15) and carry out the same inspection on the front cylinder . If the measurement is outside the specification, adjustment will be required and shimming will be necessary (follow the remainder of these instructions). Adjustment 6Using a 1/4″ allen wrench remove the 4 screws securing the rocker shaft assembly.Refit the LH support bracket and reposition the complete assembly on the rocker base. Make sure that the three dowels are in place and the slots in the rocker shafts are properly aligned with the mounting screw holes in the RH support bracket. 11Clean the threads of the 4 support bracket screws and apply Blue Loctite to the first 4 threads. 12Fit the 1-3/4″ screws into the LH support bracket (A) and the 2″ screws to the RH bracket (B). Torque all screws in cross pattern to 16-20 foot-pounds. CAUTION: The rear piston must be at TDC, compression stroke, when tightening the support bracket screws. 13Re-check the rocker end play to ensure it is within specifica- tion. 13Lubricate the two O-rings with clean engine oil and refit them in the grooves in the rocker base. 14Refit the rocker cover.

Harley-Davidson Style Rocker Cover Assemblies installation Instructions

0

Filed Under (Harley Davidson) by admin on 27-10-2010

download
Installation 1. Wash motorcycle, taking care to remove sand and other abrasive debris from engine and area of frame around engine. Remove battery, gas tanks, and all parts required to access original rocker covers. Remove top and center sections of OEM rocker housings. Refer to authorized Harley-Davidson Service Manual as necessary. WARNING – Sparks from motorcycle electrical system can ignite gasoline fumes. To prevent sparks as well as prevent electric starter from becoming engaged inadvertently and causing personal injury, disconnect battery and remove from motorcycle before proceeding. WARNING – Gasoline is toxic when fumes inhaled, extremely flammable, and explosive under certain conditions. Do not smoke around gasoline, and perform installation in a well ventilated area away from sparks and open flame. 2. Remove pushrod cover retainer clips for front cylinder and collapse covers. Remove sparkplugs and rotate engine to place pushrods at lowest point on cam with front piston at TDC on compression stroke. Referring to Harley-Davidson Service Manual as necessary, remove rocker assemblies, pushrods and lower rocker cover from front cylinder head.
3 Picture 3 Picture 4 Right Left Rocker shaft reliefs must align with these holes. NOTE – Observe correct location of pushrods. S&S pushrod kits have longest pushrod for front exhaust, next longest for rear exhaust, shortest for rear intake, and remaining one for front intake. Remove all traces of old rocker housing gaskets from cylinder head, taking care to contain debris. CAUTION – Debris such as gasket material can interfere with oil circulation resulting in engine damage not covered under warranty. 3. Inspect S&S rocker cover assemblies. Remove rough or sharp edges from plain (unchromed) assemblies. Clean all metal parts with solvent. Dry with compressed air and remove any solvent residue with clean, lint free cloth. 4. Install umbrella valves in rocker cover bases. See Picture 1. Valves go in vent ports nearest intake manifold on both front and rear rocker cover bases.

Harley-Davidson Evolution Engines S&S Billet Rocker Cover Assemblies Installation Instructions

0

Filed Under (Harley Davidson) by admin on 30-10-2010

download
1. Wash motorcycle, taking care to remove sand and other abrasive debris from engine and area of frame around engine. Remove battery, gas tanks, and all parts required to access original rocker covers. Remove top and center sections of rocker housings. Refer to authorized Harley-Davidson®Service Manual as necessary. Sparks from motorcycle electrical system can ignite gasoline fumes. To prevent sparks as well as prevent electric starter from becoming engaged inadvertently and causing personal injury, disconnect battery and remove from motorcycle before proceeding. Gasoline is toxic if fumes are inhaled, extremely flammable, and explosive under certain conditions. Do not smoke around gasoline, and perform installation in a well ventilated area away from sparks and open flame. 2. Remove pushrod cover retainer clips for front cylinder and collapse covers. Remove sparkplugs and rotate engine to place pushrods at lowest point on cam with front piston at TDC on compression stroke. Referring to Harley-Davidson®Service Manual as necessary, remove rocker assemblies, pushrods and lower rocker cover from front cylinder head. NOTE: Observe correct location of pushrods. S&S pushrod kits have longest pushrod for front exhaust, next longest for rear exhaust, shortest for rear intake, and remaining one for front intake. Remove all traces of old rocker housing gaskets from cylinder head, taking care to contain debris. Debris such as gasket material can interfere with oil circulation resulting in engine damage not covered under warranty. 3. Inspect S&S rocker cover assemblies. Remove rough or sharp edges from plain (unchromed) assemblies. Clean all metal parts with solvent. Dry with compressed air and remove any solvent residue with clean, lint free cloth. 3 CAUTION WARNING WARNING CAUTION 4. Install umbrella valves in rocker cover bases. See Picture 1. Valves go in vent ports nearest intake manifold on both front and rear rocker cover bases.

LED Motorcycle Power Box Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
This box requires the presence of a mounting plate secured to the motorcycle’s luggage rack. If the bike in question is not equipped with a mounting plate, one must be fabricated prior to installation of this box. Five mounting holes (.281″ dia.) are required to mount this box. If the motorcycle is already equipped with a mounting plate, it may be necessary to drill the 5 mounting holes required for this installation. Use the diagram shown to determine the precise location of these holes. 1. Position the box onto the mounting plate. Align the 5 vibration dampeners with the 5 mounting holes in the mounting plate. 2. Using the illustrations shown, secure the box to the mounting plate using the provided hardware. Note: Your luggage rack may already have the correct mounting holes drilled. Check the measurements below and if these holes already exist at the proper distance, remove any existing mounting hardware from the holes and secure the box with the supplied mounting hardware. 3. Place the box into its mounting position on the deck and secure it with the supplied mounting hardware as shown in the diagram. Wiring: Diagrams for optional equipment are found below. Refer to the diagram on the following page for general motorcycle box wiring information

HARLEY DAVIDSON SOFTAIL LEFT SIDE LEATHER TOOL BOX KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-04-2011

download
Installation While handling and installing tool box, be careful not to scratch surface. 1. See Service Parts Illustration. Install tool box (1) to mounting bracket (6) using button head screws (2) and washers (5). Screws (2) should be inserted through mounting holes on inside of tool box (1) and then inserted through bracket (6) holes and threaded into weld nuts attached to bracket. 2. Remove and save the two screws that secure left rear fender support to motorcycle frame. 3. Remove two bolts, nuts, and washers that secure debris deflector to motorcycle frame. This will allow you to move debris deflector out of the way when installing new passenger footpeg support bolt. Save hardware for reinstallation. 4. For 1990 to 1999 Softails: If tool box is being installed with passenger footpeg, remove the hex head bolt and left passenger footpeg. Retain footpeg and lockwasher for reinstallation. Discard bolt . If tool box is being installed without passenger footpeg, remove hex head bolt and left passenger footpeg. Discard footpeg. Retain bolt and lockwasher. For 2000 and later Softails: See page 3 . Remove footrest from clevis. Remove clevis from frame by removing cap screw from center of clevis. If tool box is installed with footpegs, keep all hardware. If toolbox is to be installed with footboards, discard hardware. 5. Slide top of mounting bracket (6) between rear fender support and frame. Align top holes in bracket with fender support holes. Align lower bracket hole with footpeg mounting hole in frame. Install the two screws, removed in Step 2, in fender support. Do not tighten screws at this time. 6. For 1990 to 1999 Softails: Place lockwasher retained in step 4 on footpeg support hex head bolt (3) from kit. CAUTION 1 of 3 For 2000 and later Softails with footpegs: Install kit 49352-00 according to instructions included in this kit. Footpeg must fold up at a 45°angle (from vertical) toward rear of motorcycle. This angle allows footpeg to fold up if, by accident, it strikes the ground surface when making a sharp turn. Failure to set footpeg to the proper fold-up angle could result in death or serious injury. 7. For 1990 to 1999 Softails: Position footpeg so it folds up and back at a 45°angle. Install bolt (3) from kit through frame, tool box bracket (6), and spacer (4), into footpeg, as shown. NOTE If vehicle is equipped with saddlebag support bracket, Part No. 90346-90 or 90346-94, position saddlebag support bracket between tool box bracket and spacer.

Incoming search terms:

Harley-Davidson Twin Cam 88 S&S Billet Rocker Covers Installation Instructions

0

Filed Under (Harley Davidson) by admin on 30-10-2010

download
Failure to confirm pushrod/lifter placement before proceeding with installation can result in damage to rocker arm support plates and other parts. With pushrods at lowest point, front piston will be at TDC on Compression stroke. 4. Remove breather cover and baffle assembly. See Picture 2. 5. Remove rocker arm/rocker support plate. See Picture 3. NOTE – Gradually loosen rocker arm support bolts in following sequence (See Figure 1): 1. Left (driveside) rear 2. Right (camside) front 3. Right (camside) rear 4. Left (driveside) front Loosen bolts in sequence and in 1⁄ 4 -turnincrements for first 3⁄ 4 turn. Bolts can then be removed according to normal procedure. 6. Remove lower rocker housing bolts. NOTE – Gradually loosen lower rocker housing bolts in following sequence (See Figure 2): 1. Right (camside) front 2. Left (driveside) rear 3. Left (driveside) front 4. Right (camside) rear 5. Center front 6. Center rear Loosen bolts in sequence and in 1⁄ 4 -turn increments for first 3⁄ 4 turn. Bolts can then be removed according to normal procedure. 7. Remove lower rocker housing and gasket from head. Remove oil and any remaining gasket material from cylinder head gasket surface and clean gasket surface with lacquer thinner

Kawasaki Prairie 650 Snorkel REMOVAL AND INSTALLATION

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove plastic from around air filter housing. Remove air filter housing lid and air filter. Remove 8 small screws from bottom of air box. Next, remove bolt from front and rear of air box. Remove the air box. Remove old snorkel from air box. Remove hose clamp and rubber drain tube from old snorkel. Reinstall on new snorkel. Install new snorkel vertical with the air box. Reinstall air box making certain all vacuum hoses are reinstalled. Check for clearance around new snorkel. Make sure all wires and steering stem do not come into contact with the snorkel. Adjust as necessary Reinstall filter and filter cover. Jetting depends on your elevation. A good starting point for 1000 feet and under is to remove the main jet #142 from the rear carburetor. Install it in the front carburetor. Purchase and install a #145 main jet in the rear carburetor. This works well with an aftermarket air filter and exhaust. For a very reasonable price, HMF Exhaust offers a jet kit with their exhaust that we recommend. Let them know Diamond G Racing sent you.

YAMAHA V-Star 1100 Carburetor Bowl Screw Repair and Removal After Stripping and Pilot Cap Removal

0

Filed Under (Yamaha) by admin on 19-01-2012

download
When I first started working on bike many years ago, I learned the danger of stripping the heads of Philips screws when removing or installing them on motorcycles. I remember the two worst screws were the casing side-cover aluminum screws and carburetor bowl screws. I think I tried every method of screw removal after they were stripped. Vice grips, better tipped screwdriver, hammer, drill, and other tools were used. One way I learned to remove stripped screws is to re-make the Philips head into a flathead screw. Cutting a slot in the top of the screw and then use a flat-head screwdriver to remove the screw. On some parts this technique can work, other parts and screws it may not. The Philips screws on the bottom of the V-Star carburetor bowls are VERY prone to stripping. In fact, I will not start a carburetor cleaning without new hex head screws to replace the original Philips bowl screws. Replace the bowl screws for yourself if you keep the bike, or for the next rider that will appreciate the hex-head screws when they clean the carburetors. Not many other parts on a V-Star have screws that are prone to stripping. This documentation is to help riders with motorcycle maintenance. Some riders will find themselves with the problem of removing stripped screws. A carburetor cleaning can quickly double in time when you realize the hardest part of the job is removing bowl screws after they strip. And then realizing you do not have the replacement hex-head screws available and must now go to the hardware store.

Incoming search terms:

Incoming search terms: