side bag for women or fz16

You search Auto repair manual PDF side bag for women or fz16, if there are search results will appear below. If search results do not exist, please search by others keyword.



  side bag for women or fz16 Direct Download speed 5282 Kb/s

  side bag for women or fz16 Full Version speed 6162 Kb/s



Harley Davidson Road Rod Saddle Bag System Kit INSTALLATION Instructions

0

Filed Under (Harley Davidson) by admin on 16-04-2012

download
Use locktite on all fasteners!! 2. Put bike on lift and place jack under frame. Raise bike to lift rear wheel. 3. If swing arm pivot shaft is drilled and tapped on each end, they need to be redrilled and tapped to 3/8-16 to a depth of _” deep. If you are unable to drill & tap your swing arm pivot shaft, you can purchase one from Cycle Visions (part #CV6121), See Harley Davidson® V-Rod® Service Manual Section 2, Page 2.89 for removal and installation instructions. 4. Remove seat, passenger seat, turn signal module, rear fender cover, turn signal license plate assembly, and rear foot peg assemblies. NOTE: Our bag system will not work with stock exhaust system… we recommend the 2-into-1 Supertrap, or you may use any exhaust system that is lower than the rear axle bolt. 5. Remove the two upper shock bolts. Relocate the shock spacer from the right side to the left side, and use the new spacer supplied on the right side. 6. Install front bag mount between frame and spacer (see Figure 1), reinstall shock bolts and torque to 31-50 lbs. 7. Install lower bag support frame to swing arm pivot shaft using the 3/8″ bolt through rear foot peg clevis and cover (see in Figure 2). NOTE: There is a right and left covers and bag support, install accordingly. Torque to 35 foot lbs. 8. Install rear fender front mounting tabs using 8mm 1.25 x _ and flat washers (supplied in kit) (see Figure 3). 9. Install upright saddlebag support brackets to the lower bag mount assembly and lower fender extension crossover mount. (see Figure 4). Torque to 25 lbs. NOTE: Install crossover mount with gusset facing down. 10. Remove license plate light from your rear turn signal bracket license plate assembly. Install license plate light on our license plate light bracket (see Figure 5). 11. Install the license plate bracket on the inside of the rear fender extension using the top holes of the license plate frame (see Figure 6 & 7). 12. Install fender washers on the inside of the fender extension (see Figure 8). 13. Install upper fender bracket to rear fender extension with a _-20 bolt supplied in kit (see Figure 9). 14. Install rear fender extension with chrome button fitted bolts. (see Figure 10 & 11). 15. To check alignment and fit of rear fender extension reinstall original rear fender. Once you have everything lined up and fitted, remove original rear fender, drill & tap (2) two 5/16 x 18 holes in rear fender support bracket (see Figure 12). 16. Install Harley Davidson® Part #70909-95 and 47449-97 bracket and receptacle on front and rear bag supports (see Figure 13 & 14). 17. Install Harley Davidson® Part #47449-97 bracket with receptable (see Figure 14). Make sure the bolts come from the inside out. This bracket is adjustable for location.

Incoming search terms:

Harley-Davidson Hard mount installation Manual

0

Filed Under (Harley Davidson) by admin on 12-04-2012

download
1. It is recommended that you create a template from cardboard or heavy paper (not included) of the back of the bag to assist in proper placement on the motorcycle. The template can be used for both bags simply by flipping it over horizontally 180 degree for slant style bags. For all other saddlebags transfer template to other bag making sure that the hole pattern corresponds with the bolts pattern on the opposite fender strut. 2-Assemble the saddlebags support 2. Remove your existing fender strut mounting bolts. 3. (A*) Install replacement 8mm x 70mm or 10mm x 70mm bolts. (Most Harley-Davidson models will utilize the 8mm bolts. Please determine which bolts will fit your specific application prior to assembly. Your make and model of motorcycle may require additional hardware. (See your motorcycle owner’s manual). 4. Install 2 upright and secure tight enough to maintain position and secure with the lock nuts (Metric applications do not require lock nuts). Ensure that bracket angles are away from the bike. 5. Lightly apply a dab of engine oil and lightly coat the exposed bolts(C or D) and barrel bolt Hex- head (E) assemblies (Mark at 4 points for each saddlebag). You can also use a marker or pen to mark. Take the template or bag and place against the brackets. Hold and press firmly to transfer the oil to the bag or template. The oil will leave a mark on the bag or template. If you are not satisfied with the position of the bag wipe the oil off and repeat as many times as necessary. Note: Position according to your specific setup, ensure the bag will not contact hot engine or exhaust components. If planning on carrying a passenger, ensure that there is enough clearance for the passenger’s legs between the bags and the foot pegs. Make sure that the uprights DO NOT contact moving parts, including but not limited to suspension components. 6. Place the Saddlebag on a firm surface and drill 4 holes (make sure you drill holes according to the size of the bolt to be passed) into the back of the bag only, according to your oil drop pattern. Also be careful not to damage the large mesh pocket inside the saddlebag. If a template was utilized cut the corresponding holes into the template and place temple on the back of the bag and drill following above directions. The template can be utilized for both sides of the bag

Incoming search terms:

HARLEY DAVIDSON T-PAK RACK BAG INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION See the Accessory and Cargo section in your Owner’s Manual. Improper loading of cargo or installation of accessories can affect motorcycle stability and handling, which could result in death or serious injury. (00021a) •Secure the bag straps to the rack to prevent bag shifting during vehicle operation. •See the owner’s manual for recommended tire inflation pressure. 1. See Figure 1. Set the rack bag on top of the luggage rack with carrying handle (1) toward the rear of the vehicle. 2. Install the four corner clips to the connector straps. 3. See Figure 2. Wrap the connector straps around the bars of the luggage rack and install the ends into the strap keepers. Tighten the straps as necessary. Tuck in to tie down any excess strap material. 4. Give the rack bag a final pull to verify the pack is securely attached.

HARLEY DAVIDSON MULTI-POCKET WINDSHIELD BAG INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
Installation 1. Remove the acorn nuts from the inside-center, left and right on the horizontal windshield bracket. 2. Apply protective tape strips to the horizontal windshield bracket to protect chrome finish. 2. Place windshield bag and bracket with eyelets over screws in the horizontal windshield bracket. Mark the location of the vertical supports for correct placement of the rubber bumpers to protect the bottom of the bag bracket. Place two bumpers each at the marked locations of the vertical windshield supports. 3. Align the metal brace with the eyelets, to fit snugly onto the windshield horizontal bracket screws. 4. Fasten the acorn nuts removed in step 1 onto the screws through the eyelets under the windshield bag. Torque the nut to 90-110 in-lbs (10.2-12.4 Nm). NOTE The brace under the bottom of the windshield bag conforms to the contour of the windshield bracket as the acorn nuts are torqued. To keep this surface in the best condition, lightly wipe with a Harley-Davidson Micro Fiber cloth, part number 94663-02, using clear water or a mild Harley-Davidson cleaner such as: • Sunwash (part number 94659-98), • Bug Remover (part number 94657-98) or • Harley Gloss (part number 94627-98).

Harley-Davidson Road King Classic Tour Pack INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
1. Close the bag completely. Support the outside of the bag with a covered piece of soft material to prevent marring or scratching. 2. Position the template on the outside of the bag, centered between the buckles. Align the template along the gap between the seams as shown at right. Tape the template in place. 3. Drill all of the small holes on the template using a 1/4″ drill bit for the assembly holes. Drill or punch the 3/4″ hole for the lock. 4. Sandwich the lock. item 4, between items 3 and 5 as shown above in FIG.1. Fasten it to the bag with the black slotted blind screws (items 7). Sandwich the leather between the lock cover plate (item 6) on the outside and the lock assembly. It may be necessary to remove a section of excess overlapped leather. 5. Use the phillips head screws (item 7) provided to attach the spring loaded ratched bar assembly. 6. Lock operation. *a. rotate the locking bar down as the bag is closed * * so that it is started into the lock aseembly. *b. check that the bag straps are outside of the bag. *c. Press the bag lid down as your help to align the * * bag lock assembly with the locking ratched bar. the ratchet bar whill operate smoothly into the * * lock when properly aligned.

HARLEY DAVIDSON LUGGAGE RACK BAG INSTALLATION INTSRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
INSTALLATION 1. Set the rack bag on top of the luggage rack with the main pocket opening facing the rear of the vehicle. 2. See Figure 2, Figure 3 and Figure 4. Determine which luggage rack is installed on the vehicle. 3. See Figure 1. Open the hook-and-loop closures in the appropriate locations for the installed luggage rack. 4. Fasten the closures around the bars of the luggage rack and pressing the hook-and-loop ends together. 5. Give the rack bag a final pull to verify the pack is securely attached. 1 2 3 4 7 5 6 is05516 1. Rear left closure 2. Rear center closure 3. Rear right closure 4. Front left closure 5. Front center closure 6. Front right closure 7. Rain cover storage Figure 1. ook-and-Loop Closure Locations 1 2 3 4 5 6 is05513 Figure 2. Premium Rack Closure Locations -J00861 1 of 2 1 3 4 6 is05514 Figure 3. Air Wing Rack Closure Locations 2 5 4 6 is05515 Figure 4. Contoured Rack Closure Locations USAGE Do not exceed luggage rack weight capacity. Too much weight can cause loss of control, which could result in death or serious injury. (00373a) •Combined load of top rack and Tour-Pak® must not exceed 25 lbs (11.3 Kg). Overloading the motorcycle will cause unstable handling and reduced braking efficiency, which could result in death or serious injury. See Figure 1. Open the hook-and-loop flap on the rain cover storage pocket (7) and wrap the tethered rain cover around the bag.

Honda VT1100C Shadow, Aero, Sabre SPECIFIC-FIT SADDLEBAGS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 23-04-2011

download
The saddlebag supports are hinged 3 so they can adjust to any variance in your motorcycle’s fender strut bolt locations. The supports have a one-inch offset 4 that angles the supports outward so they space the bags away from the motorcycle’s chassis components, wheels, brakes, and moving parts. Before removing or changing any hardware, hold the supports next to the motorcycle to familiarize yourself with how they will be installed. Remove the original fender mounting bolts from one side of the fender strut and temporarily mount one support with a 10mm bolt, a plastic and steel spacer, and two washers into the front fender stay bolt hole. Then insert an 8mm bolt, a plastic and steel spacer, and two washers into the rear fender stay bolt hole. Verify that each bolt is the proper length. IMPORTANT: The VT1100 Shadow Classic, Aero, or Sabre models have 10mm (front) and 8mm (rear) threaded holes in the fender strut. Use care to not insert the wrong size mounting bolt in the strut. When installing a bolt into the fender strut, check to be sure that it does not extend inside the fender further than the original fasteners. If it does, the excess length of the bolt must be cut off, or exchanged for a shorter bolt you obtain from the hardware store or a motorcycle shop. After verifying the mounting bolts are the proper length, remove the support from the motorcycle’s fender strut. Install a grommet in each of the large holes 5 on the back side of each saddlebag. Then insert a plastic spacer 6 in each of the grommets TIP: Use soapy water to lubricate the grommets so they will slip into the holes in the bag. The vehicle images in this instruction set may be different than your motorcycle. Continued on next page… 3 Lay a support 7 (with the joint towards the rear of the bag) on the back of a bag. Temporarily put the mounting bolts 8 through the support’s holes and into the plas- tic spacers in the grommets. Place one of the support clips 9 over the center of the lower portion of the support, so the two holes in the clip align with the predrilled holes in the bag. Use the 3/16” screws and nuts from the hardware kit to attach the support clip to the backup plate inside the bag. Place the nuts on the outside of the bag. Do not over- tighten the hardware, as this may cause damage to the saddlebag. Remove the mounting bolts from the support and the plastic spacers

Incoming search terms:

saddlebag locks for Heritage Softail INSTALLATION GUIDE

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
1. Center the top support channel on the inside top of the bag lid so that it is centered. Leave a gap so that the lid will close completely when overlapping the bag body. 2. Prior to drilling any holes, check that the support bar is positioned so that it will fit inside the bag when closed. Align the support bar and drill only the eight (8) holes shown in black to mount the top support rail. Mount the rail using the blind button cover screws with the closed end to the outside of the bag. Use a drop of thread lock on each screw. 3. Position the ratchet bar assembly as shown so that the rachet bar is directly over the existing bag emblem and aligned with the existing bag buttons. The center position of the bar leaves two holes exposed on either side of the

Incoming search terms:

Honda VTX1800F, VTX1300C, VTX1800C Plated Saddle Bag Installation Manual

0

Filed Under (Honda) by admin on 14-11-2010

download
Instruction Manual > Your saddlebag supports will install in just a few minutes using common tools. Read all instructions carefully and completely before installing your new saddlebag supports. 1. Remove your stock fender rail bolts. 2. Place the supplied spacers in the recessed holes on the fender rails (large spacer to the front, small spacer to the rear). 3. Install your Cobra saddlebag supports using the supplied button head bolts (where the stock bolts were removed) the saddlebag supports should hang towards the rear and away from the motorcycle. 4. Torque bolts to factory specifications. Note: If using Cobra sissy bar mount the saddlebag supports over the sissy bar brackets and do not use supplied spacers. Cobra recommends you always wear a helmet while riding. Please never operate your motorcycle while under the influence of alcohol and/or drugs. Enjoy the new look of your motorcycle and please ride safely

Honda VTX1800C Plated Saddle Bag Installation Manual

0

Filed Under (Honda) by admin on 14-11-2010

download
Instruction Manual > Your saddlebag supports will install in just a few minutes using common tools. Read all instructions carefully and completely before installing your new saddlebag supports. 1. Remove your stock fender rail bolts. 2. Place the supplied spacers in the recessed holes on the fender rails (large spacer to the front, small spacer to the rear). 3. Install your Cobra saddlebag supports using the supplied button head bolts (where the stock bolts were removed) the saddlebag supports should hang towards the rear and away from the motorcycle. 4. Torque bolts to factory specifications. Note: If using Cobra sissy bar mount the saddlebag supports over the sissy bar brackets and do not use supplied spacers. Cobra recommends you always wear a helmet while riding. Please never operate your motorcycle while under the influence of alcohol and/or drugs. Enjoy the new look of your motorcycle and please ride safely.

Incoming search terms: