sinnis apache rear foot pegs and brackets

You search Auto repair manual PDF sinnis apache rear foot pegs and brackets, if there are search results will appear below. If search results do not exist, please search by others keyword.



  sinnis apache rear foot pegs and brackets Direct Download speed 5282 Kb/s

  sinnis apache rear foot pegs and brackets Full Version speed 6162 Kb/s



1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

1300 Yamaha V-Star Installation Manual

0

Filed Under (Yamaha) by admin on 07-11-2010

download
1) Place motorcycle on a firm level surface and secure in a upright position. 2) Remove saddle bags and saddle bag hardware (Tourer model only) Also remove rear riders pegs (Tourer model requires removal of rear footpeg offset hardware as well) 3) Attach bracket A (right) / B (left) to rear footpeg attachment point using new bolts provided. Remount footpegs/saddlebag hardware over top of brackets A/B. NOTE: Do not attach leveling stand bracket at this time 4) Attach bracket C(right) / D(left) to rear fender sub frame using new bolts provided. (Tourer model only – Saddle bag hardware mounts to the outside of brackets C/D. Brackets C/D mount between chrome side rail and saddlebag hardware.) NOTE: Brackets C/D have welded spacers which attach in toward rear fender 5) Attach top of Bracket E(right) / F(left) to rear of brackets C/D. Brackets E/F mount to the inside of brackets C/D. NOTE: Use ½ inch spacer between brackets E/F and C/D on Tourer model ONLY
6) Attach rear of brackets A/B to TOP of forward hitch arms. Attach bottom to brackets E/F to rear hitch plate. 7) Carefully tighten all bolts at this time ensuring hitch is square with motorcycle. Hitch Bracket Identification Leveling stand screw jack installation 1) Attach leveling stand brackets to brackets A and B 2) Thread right side screw jack into threaded hole on leveling stand bracket attached to bracket A sand adjust leveling jack bolt out. 3) Push motorcycle over from left side until right screw jack is touching floor. 4) Thread left side screw jack into threaded hole on leveling stand bracket attached to bracket B and adjust out until motorcycle will rest upright on both screw jacks. 5) Adjust screw jacks until motorcycle is level. 6) After InstaTrike is attached to or removed from receiver hitch, be sure to remove leveling stands and leveling stand brackets. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position.
INSTALLATION OF THE TOW-PAC HITCH CART. 1. Place your motorcycle on a smooth flat surface, like a garage floor, and install leveling stands. Install right leveling stand first. Carefully raise motorcycle off of side stand and install left leveling stand. Caution – Use leveling stands to level motorcycle ONLY. Do not raise motorcycle with stands Caution – Be certain that motorcycle is always in a stable balanced position when installing leveling stands. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bolt

Incoming search terms:

1999-2008 FLHT Series Harley- Davidson Trike Conversion Kit Installation Instructions

0

Filed Under (Harley Davidson) by admin on 04-12-2010

download
1. Place the motorcycle on the lift. 2. Place a suitable Jack under the Frame of the Motorcycle and tie down securely. 3. Remove Drain Plug from Primary Cover Assembly and drain oil. 4. Slide Rubber Boot off of the Clutch Cable Adjuster. Loosen and back the Jam nut away from the Clutch Cable Adjuster. Move Clutch Cable Adjuster towards the Jam Nut to introduce free play in the Clutch Lever. 5. Remove the ¼ – 20 Phillips head screw and Seat. 6. Disconnect negative Battery Terminal. 7. Remove two ¼ – 20 flanged hex nuts from the Stud Plate. Save the Passenger Handrail and two nuts. 8. Remove the Saddle Bags. 9. Remove the Right and Left Side Covers. 10. Remove Inner Tour Pak Molded Liner. 11. Disconnect the Tour Pak wiring. 12. Remove five ¼ – 20 HHCS, ¼ – 20 nyloc nuts, and Aluminum Spacers. 13. Remove Tour Pak from Top Support Tube. 14. Loosen Muffler Clamp on both Mufflers and remove 2 5/16 – 18 HHCS per Muffler. Remove and discard both Mufflers. Save Muffler Clamps. 15. Remove and discard Muffler Support Plates. 16. Remove both ¼ – 20 HHCS and Front Saddle Bag Brackets. 17. Remove the twelve 5/16 – 18 Torx HCS six 5/16 – 18 nuts, and the Left and Right Saddle Bag Guards. 18. Remove the Air Line Junction from the Rear Fender. 19. Disconnect the Rear Lamp Wiring Harness and remove from T-stud Clip.
6 20. Remove two 5/16 – 18 Phillips head screws. Remove the Left and Right Frame Covers. 21. Remove two 5/16 – 18 Torx HCS. Remove and save the Top Tour Pak Support Tube Top. 22. Remove four 5/16 – 18 Torx HCS. Remove the Left and Right Rear Saddle Bag Guard Support Bracket. 23. Remove four 5/16 – 18 HHCS. Remove and save the Tour Pak Support Tube Bottom. 24. Remove and discard the Air Valve Assembly Bracket. 25. Remove four ½ – 13 HHCS and washers. Remove and discard both Rear Air Shock Absorbers. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. NOTE: if ABS equipped refer to separate instructions. 26. Drain all Brake Fluid from the Rear Brake System. 27. Cut and remove Cable ties and un-clamp Wire Harness Loops from the Rear Brake Line along its length, including Clamps on Swing Arm. 28. Remove the 10 – 24 flanged HHCS and Rear Brake Hose Clamp from the Right Rear Fork Bracket. 29. Remove ¼ – 20 SHCS from Rear Stop Lamp Switch Bracket. 30. Remove and discard Banjo Bolt and Crush Washers on Rear Brake Caliper. 31. Remove the Spring Clip and nut from the Rear Axle. 32. Remove Rear Axle and Rear Wheel Spacers. 33. Push Rear Wheel Assembly forward and slip Rear Belt off of the Rear Sprocket. 34. Remove Rear Brake Caliper. 35. Slide Rear Wheel Assembly rearward. Remove one 5/16 – 18 Torx HCS from inside the Rear Fender well. 36. Slide Rear Wheel Assembly forward. Remove two 5/16 – 18 Torx HCS. Remove Rear Fender. 37. Remove and save the two Retaining Washers from the Stud Plate. Remove and save the Stud Plate

Incoming search terms:

Yamaha V-Star 1300 Receiver Hitch Installation

0

Filed Under (Yamaha) by admin on 01-01-2012

download
Install all bolts loosely until all brackets are in place Remove accessories (saddle bags, back rests, etc) before hitch installation. 1) Place motorcycle on a firm level surface and secure in a upright position. 2) Remove saddle bags and saddle bag hardware (Tourer model only) Also remove rear riders pegs (Tourer model requires removal of rear footpeg offset hardware as well) 3) Attach bracket A (right) / B (left) to rear footpeg attachment point using new bolts provided. Remount footpegs/saddlebag hardware over top of brackets A/B. NOTE: Do not attach leveling stand bracket at this time
4) Attach bracket C(right) / D(left) to rear fender sub frame using new bolts provided. (Tourer model only – Saddle bag hardware mounts to the outside of brackets C/D. Brackets C/D mount between chrome side rail and saddlebag hardware.) NOTE: Brackets C/D have welded spacers which attach in toward rear fender 5) Attach top of Bracket E(right) / F(left) to rear of brackets C/D. Brackets E/F mount to the inside of brackets C/D. NOTE: Use ½ inch spacer between brackets E/F and C/D on Tourer model ONLY
6) Attach rear of brackets A/B to TOP of forward hitch arms. Attach bottom to brackets E/F to rear hitch plate. 7) Carefully tighten all bolts at this time ensuring hitch is square with motorcycle.

Harley Davidson Road Rod Saddle Bag System Kit INSTALLATION Instructions

0

Filed Under (Harley Davidson) by admin on 16-04-2012

download
Use locktite on all fasteners!! 2. Put bike on lift and place jack under frame. Raise bike to lift rear wheel. 3. If swing arm pivot shaft is drilled and tapped on each end, they need to be redrilled and tapped to 3/8-16 to a depth of _” deep. If you are unable to drill & tap your swing arm pivot shaft, you can purchase one from Cycle Visions (part #CV6121), See Harley Davidson® V-Rod® Service Manual Section 2, Page 2.89 for removal and installation instructions. 4. Remove seat, passenger seat, turn signal module, rear fender cover, turn signal license plate assembly, and rear foot peg assemblies. NOTE: Our bag system will not work with stock exhaust system… we recommend the 2-into-1 Supertrap, or you may use any exhaust system that is lower than the rear axle bolt. 5. Remove the two upper shock bolts. Relocate the shock spacer from the right side to the left side, and use the new spacer supplied on the right side. 6. Install front bag mount between frame and spacer (see Figure 1), reinstall shock bolts and torque to 31-50 lbs. 7. Install lower bag support frame to swing arm pivot shaft using the 3/8″ bolt through rear foot peg clevis and cover (see in Figure 2). NOTE: There is a right and left covers and bag support, install accordingly. Torque to 35 foot lbs. 8. Install rear fender front mounting tabs using 8mm 1.25 x _ and flat washers (supplied in kit) (see Figure 3). 9. Install upright saddlebag support brackets to the lower bag mount assembly and lower fender extension crossover mount. (see Figure 4). Torque to 25 lbs. NOTE: Install crossover mount with gusset facing down. 10. Remove license plate light from your rear turn signal bracket license plate assembly. Install license plate light on our license plate light bracket (see Figure 5). 11. Install the license plate bracket on the inside of the rear fender extension using the top holes of the license plate frame (see Figure 6 & 7). 12. Install fender washers on the inside of the fender extension (see Figure 8). 13. Install upper fender bracket to rear fender extension with a _-20 bolt supplied in kit (see Figure 9). 14. Install rear fender extension with chrome button fitted bolts. (see Figure 10 & 11). 15. To check alignment and fit of rear fender extension reinstall original rear fender. Once you have everything lined up and fitted, remove original rear fender, drill & tap (2) two 5/16 x 18 holes in rear fender support bracket (see Figure 12). 16. Install Harley Davidson® Part #70909-95 and 47449-97 bracket and receptacle on front and rear bag supports (see Figure 13 & 14). 17. Install Harley Davidson® Part #47449-97 bracket with receptable (see Figure 14). Make sure the bolts come from the inside out. This bracket is adjustable for location.

Incoming search terms:

Yamaha Virago 750/ 1100 InstaTrike REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Yamaha) by admin on 26-12-2011

download
Remove any aftermarket accessories (saddle bags, back rests, etc) before hitch installation. After installation remount accessories. NOTE: Some aftermarket accessories may not be compatible with InstaTrike hitch. 1) Place motorcycle on a smooth level surface on center stand. 2) Attach Bracket A (left) to outside of rear passenger foot peg mount. Place spacers between Bracket A and foot peg mount. Use new bolts provided. 3) Attach Bracket B (right) to outside of rear passenger foot peg. Place spacers between Bracket B and foot peg mount. Use new bolts provided. Bracket will extend over top of mufflers. 4) Attach Brackets C (left) and D (right) to rear frame bolts on
motorcycle. Located near rear turn signals Use new bolts provided. (10M x 25mm long) It may be necessary to loosen or remove backrest covers or hardware in order to easily access rear frame bolts. After Bracket C and D installation, reattach and/or tighten backrest mounts. 5) Attach Bracket E(left) / F(right) to bottom of Brackets A & B and to the TOP of the forward hitch arms. Ensure hitch is square on motorcycle and snug bolts for Brackets A, B, and E,F at this time. 6) Raise rear of hitch so bottom of Brackets C & D are flush with top of rear hitch plate. Ensuring that hitch is square with motorcycle, carefully mark hole locations for bottom of Brackets C&D on rear hitch plate. Drill rear hitch plate holes with 3/8 inch drill. This step ensures proper alignment and spacing of hitch on the motorcycle. 7) Tighten all bolts ensuring that hitch is square on motorcycle. Periodically check bolts for tightness. Bracket Identification
INSTALLATION OF THE TOW-PAC HITCH CART.
1. Place your motorcycle on a smooth flat surface, like a garage floor, and rest it on its center stand. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bo

Incoming search terms:

Honda Goldwing GL1800 Solid Rear Axle Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Specifications Overall Width: 57.75″ Overall Length: 108″ Overall Length w/EZ-Steer 109.5 Wheel Base: 71″ Extended 4.5″ At Rear Axel Wheel Base w/EZ Steer 72.5″ Load Capacity: 500 Lb Tire Size: 205 / 70 / R15 Wheel Size (15″) Offset +35 mm 15x7JJ 4×4.5 Tire Pressure 20 PSI Suspension: “Zero-Flex” Internal Swing Arm utilizing 3 shocks, OEM shock absorber plus 2 coil over shock absorbers. Rear Differential: Champion Lightweight rear axle / differential assembly. Gear Ratio 2.93:1 gear ratio Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 6.75 cubic feet. 3 full-face helmets and additional storage. Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 7 of 28 Revision 10 4 Removal of Original Parts Most tasks necessary in this guide can be accomplished with the vehicle on its center stand. Secure the center stand to one of the forward crash bars with a ratchet strap to keep vehicle from rolling forward and off the center stand. Be sure that the vehicle is laterally stable as well. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for return of deposit or re-installation after modification shall be duly noted. • Seat (to be re-installed without modification) • Left and right side covers (to be re-installed without modification) • Battery and battery box (to be re-installed without modification) • Left and right saddle bags • Remove taillight and locking assemblies from saddlebags (to be returned for refund of deposit) • Trunk (to be re-installed without modification) • Left and right passenger foot rests (to be re-installed without modification) • Left and right foot rest under covers (to be modified and re-installed) • Left and right rear crash bars • Saddle bag trunk stay (to be modified and re-installed) • Left and right mufflers (Mufflers only, do not remove decorative covers) • Rear wheel • Left and right pivot bolt covers (to be re-installed without modification) • Reverse resistor (to be relocated) • Swing Arm – Note : Carry out brake system modifications (Section 5) prior to removing Swing Arm. • Note : Upper bolt of mono shock can be removed without removing the fuel tank. • Note : Do not remove actuator hose from actuator pump or shock absorber. Dismounting shock actuator pump will allow more movement of shock absorber when removing swing arm.Trike Conversion Installation Kit Honda Goldwing GL1800 Champion Trikes Page 8 of 28 Revision 10 5 Brake System Modification Note : Modification to the vehicle brake system should be carried out prior to removal of the swing arm. From the manufacturer, your Honda Gold Wing brake system utilizes both front and rear brakes when the foot brake is applied. In order to insure safe operation of your Gold Wing when converted to a Champion Sidecars Trike, the brake system must be modified to isolate the front and rear brake systems from each other. Once modification is complete, four of the six pistons in the front calipers operate only when the hand brake lever is applied. The rear brakes operate only when the foot brake pedal is applied. The diagrams below outline the difference between the GL1800 OEM brake system and the system as modified by the Champion Sidecars Trike Conversion Kit.

Incoming search terms:

HARLEY DAVIDSON TRI-BAR AUXILIARY RUNNING LIGHT/ BRAKE LIGHT ASSEMBLY REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
REMOVAL 1. Remove the saddlebags and left side cover. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. Remove the main fuse. 3. See Figure 1. Remove six flange nuts (1) from the right and left fender stud plates (2). 1 2 3 5 4 is04366a 1. Nut 2. Stud plate 3. Rear fascia 4. TORX screw 5. Lamp assembly Figure 1. FLHX Rear Fascia and Lamp 4. On the left side of the motorcycle, loosen the set screw and unscrew the radio antenna mast. 5. Gently open the adhesive conduit at the split line to release the rear fascia light harness. 6. At the rear of the motorcycle, spread the top of the fascia to release from the top studs at the side of the fender and then pull the bottom in a downward direction to release the fascia from the fender. If necessary, gently wiggle the fascia while pulling. 7. 2006-2008 models only: On the left side of the motorcycle, remove the bolt (with flat washer) to remove the passenger seat strap and saddlebag front mounting bracket from the chrome frame tube cover. 8. Remove the screw and chrome frame tube cover. NOTE ALL models: Make note of the wire routing and location of all cable straps. New light wiring installs the same way. 9. See Figure 2. Release the rear fascia light wires from the wire clip (1). Cut the cable straps (2) to release the rear fascia light harness (3) and radio antenna cable. 10. 2006-2008 models: Disconnect the rear fascia light connector [12B] located inboard of the upper frame tube. 2009 and later models: Disconnect the rear fascia light connector [12B] located to the rear of the fuse panel. 11. See Figure 1. Remove the two T-20 TORX® screws to release the light assembly from the fascia. Save the screws for installation of the new light. 1 3 4 2 is04378 1. Wire clip 2. Cable strap 3. Fascia light harness 4. Flange nut Figure 2. Rear Fascia Light Harness INSTALLATION 1. Route the rear fascia light wires forward through the cable clip at the top of the radio antenna bracket and then upward in front of the saddlebag rear mounting bracket to the inboard side of the upper frame tube. 2. 2006-2008 models: On the inboard side of the upper frame tube, mate the pin and socket housings of the rear fascia light connector [12]. 2009 and later models: To the rear of the fuse panel, mate the pin and socket housings of the rear fascia light connector [12]. 3. Using the slotted hole, install a new cable strap to secure the rear fascia light wires and radio antenna cable to the rear fender support. 4. Install a new cable strap to secure the rear fascia light wires and radio antenna cable to the shoulder of the upper frame tube (just in front of the air valve mounting bracket).

Incoming search terms:

650 Yamaha V-Star InstaTrike REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 29-12-2011

download
install all bolts loosely until all brackets are in place y Remove any aftermarket accessories (saddle bags, back rests, etc) before hitch installation. After installation remount accessories. NOTE: Some aftermarket accessories may not be compatible with InstaTrike. 1) Place motorcycle on a firm level surface. 2) Remove rear foot pegs and bolts 3) Attach bracket A (left) and bracket B (right) to the inside of the rear foot peg bracket and reattach rear foot pegs using new bolts provided. 4) Attach front of bracket C (left) and bracket D (right) to bottom of brackets A and B 5) Attach bracket E (left) and bracket F (right) to two rear fender attachment bolts using new bolts provided 6) Attach brackets G and H to rear of brackets E and F 7) Attach bottom of brackets G and H to hitch plate. 8) Attach rear of brackets C and D to TOP of forward hitch arms. 9) Tighten all bolts. Installation Diagram Leveling stand screw jack installation 1) Thread right side screw jack into threaded hole on bracket D 2) Push motorcycle over from left side until right screw jack is touching floor. 3) Install left side screw jack on bracket C and adjust out until motorcycle will rest upright on both screw jacks. 4) Adjust screw jacks until motorcycle is level. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position

BMW Motorcycle R 1100 RS – Rear Frame

0

Filed Under (BMW) by admin on 16-11-2010

download
Complaint: On R 1100 RS models (above serial numbers only) with luggage racks, a crack may develop in the rear section of the frame (see drawing) if a load exceeding the permitted 11 lb. is applied to the luggage rack, or if a top case is used. Remedy: Please check all R 1100 RS models (in serial number range above) which pass through your workshops for cracks on the rear section of the frame. Cracked frames should be exchanged with the new part listed below. The new rear frame has been reinforced to use with larger loads. New Part: 46 51 2 320 698 (reinforced rear frame) Caution: Since the introduction of the rear luggage grid to accommodate the 33 liter removable top box, it is vital that this luggage grid and 33 liter top box not be installed on any of the above unless the reinforced rear frame is fitted, or a frame reinforcement kit is installed (a kit will be made available in the future to reinforce the rear frame of the above models, in order to install the 33 liter top box). The new reinforced rear frame (46 51 2 320 698) has been fitted since May 1995 production. Use of the new rear section of frame on an earlier production bike requires a new rear section of the dual seat as follows: Parts 52 53 2 325 121 Flash Green 52 53 2 325 122 Red Needed: 52 53 2 325 123 Black 52 53 2 325 120 Light Gray 52 53 2 325 211 Anthracite Warranty: Please explain to your customers that the top case can only be installed on bikes with reinforced rear frames. Claims for frame cracks which result from operation with large loads beyond specification will not be honored under the terms of the Limited Motorcycle Warranty.

Incoming search terms: