sizes and types and torque specs of front motor mount for a 2006 road king classic

You search Auto repair manual PDF sizes and types and torque specs of front motor mount for a 2006 road king classic, if there are search results will appear below. If search results do not exist, please search by others keyword.



  sizes and types and torque specs of front motor mount for a 2006 road king classic Direct Download speed 5282 Kb/s

  sizes and types and torque specs of front motor mount for a 2006 road king classic Full Version speed 6162 Kb/s



HARLEY DAVIDSON ROAD KING SOLO BUCKET AND PASSENGER PILLION INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
Installation SOLO SADDLE ONLY 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider solo seat. 2000 and later models . Remove the retainer washer from the stud plate and replace with two black retainer washers (2). Be careful not to allow stud plate to fall through the fender. 3. Road King standard models . Install stock solo seat mount bracket using two stock screws saved in Step 2. Road King Classic Custom models . Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. Install seat by sliding front of seat into seat holder bracket. Pull up on the nose of the seat to verify that the seat is securely installed. After installing seat, pull upward on front of seat to be sure it is in locked position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070a) 5. 1999 and later models . Install 1/4 in. star washers (6), spacers (4) and acorn nuts (3) onto rear mount studs. Torque to 72 in-lbs (8.13 Nm). 1998 and earlier models . Install 5/16 in. star washers (5) and 5/16-18 x 3/4 in. buttonhead screws (1) into stock mount nuts. Torque to 17 ft-lbs (23 Nm). SOLOAND PILLION 1. Remove stock seat and grabstrap according to applicable Service Manual instructions. Retain all hardware for later use. 2. Road King standard models . Remove and save the stock screws and seat mount bracket at the back of the rider seat. 3. Road King standard models. Install stock seat mount bracket onto new solo seat using two screws saved in Step 2. Road King Classic Custom models. Install solo seat mount bracket onto back of solo seat using bracket and screws included in Mount Kit Number 52903-01. 4. 1999 and later Road King standard models . Secure the rear mount bracket with stock mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). 1998 and earlier Road King standard models . Install solo seat by sliding front of seat into holder bracket on bike. Secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm). Road King Classic Custom models . Mount Kit Number 52903-01 is required for installation. Install solo seat (7) by sliding front of seat into holder bracket on bike. • 1999 and later models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom nuts (10) and two 1/4 in. star washers (6). Torque to 72 in-lbs (8.13 Nm). • 1998 and earlier models . Using Mount Kit Number 52903-01, secure the rear mount bracket with the two mushroom screws (11) and two 5/16 in. star washers (5). Torque to 17 ft-lbs (23 Nm)

Incoming search terms:

2000 Harley-Davidson FLHRCI Road King Classic

0

Filed Under (Harley Davidson) by admin on 03-11-2010

download
the Road King® Classic is a motorcycle with enough traditional styling to drop jaws throughout the continent. The Road King® Classic boasts laced wheels, fat white-walls and gorgeous leather saddlebags with hard inserts so they keep their shape across the long miles. Slightly narrower new handlebars provide improved ergonomics. Fender tips, tank and seat valance all boast a metal emblem. The model is available with a fuel-injected, chrome-and-black Harley- Davidson® Twin Cam 88 engine. Specifications: Engine Type: 1449 cc, 4-Stroke, Air Cooled, V-Twin Engine Bore and Stroke: 95.3 mm x 101.6 mm Valves 2 valves/cylinder Claimed Horsepower: 67 hp (50 kW) @ 5200 rpm Maximum Torque: 110 Nm (81.1 ft. lbs) @ 3100 rpm Transmission type: 5 speed Final Drive: Belt Tire – Front: 130/90-16 Tire – Rear: 130/90-16 Brakes – Front: dual 292 mm discs with 4-piston calipers Brakes – Rear: single 292 mm disc with 4-piston calipers

Harley Davidson FL series Electra Glide, Ultra Classic, Road King, Road Glide Left and Right Mounting Plate Installation Installation Manual

0

Filed Under (Harley Davidson) by admin on 25-02-2012

download
Remove existing control arm end cap and grind the outside flush. See picture below for reference. The swing arm will drop if both sides are removed at the same time. To ease installation, complete one side before starting on the other. Note: there is a left and right. Left and right end caps shown. 2. Install mounting plate assembly 10002351 on top of the end cap using 7/16″ hex head bolt and lock washer in the bottom hole. Use the 7/16″ counter sink bolt in the top hole. Make sure the end cap is seated properly. The end cap notch should fit into the recess on the frame. The pivot arm assembly is shipped on mounting plate assembly; you may remove the pivot arm to make installation easier. 3. Snug up the bolts evenly, make sure the end caps are not crooked in relation to the frame. Tighten both bolts to 25 ft lbs. (Further tightening will be required after the toe in is set). 4. If you removed the left hand pivot arm assembly, remount it now, 10002575-A (pg 20) with seal, bearings (2), washer, nut, cotter pin and dust cover. 5. Repeat for right hand side. 5 Toe In Adjustment Adjustment made with the mounting plates, bolts, pivot arms, and hubs (without wheels and tires) in place

Incoming search terms:

TRIUMPH ROCKET III TIP OVER BARS INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-12-2010

download
1. Starting on the right side (towards the front of the motor) locate the three mounting bolts that secure the brake assembly bracket (a chrome tube) to the bottom of the motor. Remove the bottom and front bolts. Repeat for left side. 2. Locate the front motor mount bolt. This is the black bolt located at the very front of the engine about halfway down behind the radiator. Remove the nut from this bolt on the left side. Properly secure the bike and use a jack to lift up on the motor to release the pressure from the motor mount bolt. Remove the bolt. 3. On the right side place the motor mount bolt thru the upper mounting hole of the right tip over bar. Install the tip over bar by feeding the motor mount bolt thru the original hole and inserting the two bolts (supplied) into the bottom mounting holes. (Do not tighten yet.) 4. On the left side install the top of the left tip over bar by inserting it into the right side tip over bar. Align the tip over bar so that the motor mount bolt extends thru the upper mounting hole. Thread the original locking nut onto the motor mount bolt a couple of turns. Now align the bottom of the tip over bar and install the remaining two bolts (supplied). Tighten the motor mount bolt (torque to 28-32 ft/lbs) and the lower four bolts (torque to 14-18 ft/lbs) securely. 5. Re-check all hardware for tightness

HARLEY DAVIDSON CHROME OIL FILTER MOUNT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 04-02-2011

download
INSTALLATION 1. See Figure 2. Remove oil filter (B). 2. Remove existing oil filter mount screws and washers and remove existing oil filter mount. Discard original screws and washers. 3. Remove original oil filter adapter (A) from old mount. Clean all oil from adapter, then apply Loctite 243 (blue) to the threads on the side of the adapter that mates with the new mount. Install adapter into new mount (1). 4. Place new O-rings (2) from kit into bottom of new chrome oil filter mount (1), place oil filter mount in position, and install new oil filter mount screws (4), lockplate (5), and washers (3) from kit. Lockplate must be positioned as shown in Figure 2. NOTE Carefully follow the instructions for installing the lockplate. Failure to correctly install the lockplate could cause the fasteners to turn and allow the filter mount to loosen. A loose filter mount could allow hot oil to spray onto riders or the motorcycle which could lead to personal injury and/or death. 5. Use Loctite 243 (blue) on threads. Insert upper and lower hex bolts through lock plate. Position flat washer behind lockplate and thread hex bolts into case. Snug bolts but do not tighten. 2 4 1 3 is03977 1. Top bolt 2. Center bolt 3. Lower bolt 4. Center bolt, re-torque Figure 1. Torque Sequence NOTE On FL models, it may be necessary to clip clutch cable strap on frame downtube and move cable to the side. This will allow easier access when tightening new oil mount hex head bolts. 6. See Figure 1. Tighten hex head bolts to 130-140 in-lbs (14.6-15.8 Nm). Tighten hex head bolts starting with top (1), middle (2), bottom (3), then re-tighten middle bolt (4). 7. See Figure 2. Carefully bend over lockplate (5) edges at top and bottom fastener to prevent hex head bolt from turning. 8. Install oil filter (B)

YAMAHA 1996-2003 Road Star BILLET TACH MOUNT KIT INSTALLATION MANUALS

0

Filed Under (Yamaha) by admin on 12-01-2012

download
Remove and retain the (4) chrome caps from the handlebar clamps. Remove and retain the (4) stock allen head bolts. This hardware will be re-used with the new Billet Tach Mount Kit. Carefully remove the stock handlebar clamps while supporting the handlebars. INSTALLATION: 2. Slide the Electronic Tachometer (#6) into the Billet Tach Mount (#2) and secure with the 10-24 X 1/4″ Socket Set Screw (#10) supplied. Carefully pull the tachometer wire harness through the larger hole in the Billet Tach Cup (#3) and secure the Billet Tach Cup with the 10-24 X 1/8″ Socket Set Screw supplied. (The additional holes in the tach cup are for air circulation). Attach the Billet Tach Mount to the Billet Handlebar Clamp (#1) with the two 10-24 X 1-3/4″ Socket Head Screws (#4) supplied. Install the Billet Tach Mount assembly with the four stock allen head bolts and chrome caps removed in step 1 above. Adjust handlebars to desired height and torque bolts to factory specs. WIRING INSTRUCTIONS: 3. Refer to FIG. #1 . Remove Seat. Disconnect negative cable from battery. Remove fuel tank retaining bolts. Raise fuel tank about 3″-4″ to expose the Left Side Ignition Coil. It is not necessary to completely remove the gas tank on the Road Star. (V-Star 1100 applications use the right front coil and require fuel tank removal.) TIP: Long needle nose pliers are useful in removing and re-installing the coil wires. If desired, tach wire loom may be shortened as necessary. Using an appropriate crimping tool, connect the Tachometer wires in the following manner: Cut Shrink Tubing (#9) into two 1″ pieces

HARLEY DAVIDSON ROAD KING CLASSIC FRONT FENDER SKIRT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-04-2011

download
INSTALLATION 1. Remove fasteners from stock fender skirt. NOTE Some early models have rivets for fasteners. These rivets will need to be drilled out. Drill the rivet heads to a sufficient depth to remove the head from the rivet shaft. Do not attempt to drill the rivet all the way through. This may scratch the fender?s painted surface. 2. Remove stock fender skirt. 3. Thoroughly clean the fender under the skirt. At this point it may be a good idea to wax this portion of the fender to prevent rust in the future. 4. See Figure 1. Cut the adhesive foam strip (5) into three equal parts. Remove the backing from the adhesive strips and apply adhesive on middle and two sides at the inside/bottom of the fender skirt (1). The foam strips will prevent rattling and unwanted noise. NOTE On some later FLT models, there may not be enough fender skirt support to allow the application of adhesive strips. If this is true for your motorcycle, you may install this kit without the adhesive strips. 5. Place the fender skirt in position, aligning fastener holes. 6. Install the screws (2) from the outside of the fender. Install the washers (4) and nuts (3) inside the fender. 3 2 4 1 5 is03865 1. Fender skirt 2. Screws 3. Locknuts 4. Washers 5. Adhesive foam strip Figure 1. Front Fender Skirt and Hardware

Harley-Davidson Road King Classic Tour Pack INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
1. Close the bag completely. Support the outside of the bag with a covered piece of soft material to prevent marring or scratching. 2. Position the template on the outside of the bag, centered between the buckles. Align the template along the gap between the seams as shown at right. Tape the template in place. 3. Drill all of the small holes on the template using a 1/4″ drill bit for the assembly holes. Drill or punch the 3/4″ hole for the lock. 4. Sandwich the lock. item 4, between items 3 and 5 as shown above in FIG.1. Fasten it to the bag with the black slotted blind screws (items 7). Sandwich the leather between the lock cover plate (item 6) on the outside and the lock assembly. It may be necessary to remove a section of excess overlapped leather. 5. Use the phillips head screws (item 7) provided to attach the spring loaded ratched bar assembly. 6. Lock operation. *a. rotate the locking bar down as the bag is closed * * so that it is started into the lock aseembly. *b. check that the bag straps are outside of the bag. *c. Press the bag lid down as your help to align the * * bag lock assembly with the locking ratched bar. the ratchet bar whill operate smoothly into the * * lock when properly aligned.

Harley-Davidson Road King Classic Saddlebag Locks INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 24-10-2010

download
1. Cut off the back stud (at the pointed end of the emblem) with a hacksaw. Hacksaw must have a fine tooth metal cutting blade. Allow blade to slide along the flat edges of the emblem as shown. 3. Place washer (J) over emblem stud and insert threaded stud through the hole in the backing plate (L). Place cloverleaf spring (K) over the stud and onto the backing plate with the dome facing up. Place flat washer (J) and nylon cap nut (I) on the stud and tighten until a smooth open/close rotation is achieved. See illustration at right. Emblem should snap in place and not rattle* 2. Thread the front stud with the tap provided. OIL THE STUD FIRST. Thread the stud square, using a socket or wrench. Make no more than a half turn at one time, always backing up one-half turn each time. 4. Pin template on the bag with #10 screws (T) provided. Make two 5/16″ holes where shown. Make one 3/4″ hole where shown with a punch, hole saw or drill bit. If drilling the 3/4″ hole always cut the leather off first using a sharp knife. Punches, either knock-out type or gasket type do the best job without removing the leather layer

Yamaha R1 2007-2008 Frame Slider Installation

0

Filed Under (Yamaha) by admin on 01-01-2012

download
Installation Steps: 1. Remove left and right body panels. 2. Remove the left side engine stud. Mount the left side offset using 99-HB-SH10125080 Socket Cap 10 X 1.25 X 80 Main Engine Stud. Tip: Only tighten enough so you can still move the offset by hand. Loosely mount the left side body panel. Adjust the offset so the frame slider when mounted will clear the bodywork. There is also a groove cut in the offset, this is so the body can clear the offset. 3. With the offset in the correct position remove body and torque down to OEM torque specs. 4. Using one drop of blue thread locker mount the left side puck to the offset with 99-HB- SH10150045 Socket Cap 10 X 1.5 X 45 (Holds puck to offset). Torque down to 30 to 32 foot lbs. 5. Remove the right side engine stud. Mount the right side offset using 99-HB-SH10125080 Socket Cap 10 X 1.25 X 80 Main Engine Stud. Tip: Only tighten enough so you can still move the offset by hand. Loosely mount the right side body panel. Adjust the offset so the frame slider when mounted will clear the bodywork. There is also a groove cut in the offset, this is so the body can clear the offset. 6. With the offset in the correct position remove body and torque down to OEM torque specs. 7. Using one drop of blue thread locker mount the right side puck to the offset with 99-HB- SH10150045 Socket Cap 10 X 1.5 X 45 (Holds puck to offset). Torque down to 30 to 32 foot lbs. 8. Mount left and right bodywork

Incoming search terms:

Incoming search terms: