smog removal klx450r

You search Auto repair manual PDF smog removal klx450r, if there are search results will appear below. If search results do not exist, please search by others keyword.



  smog removal klx450r Direct Download speed 5282 Kb/s

  smog removal klx450r Full Version speed 6162 Kb/s



YAMAHA V-Star 1100 Carburetor Bowl Screw Repair and Removal After Stripping and Pilot Cap Removal

0

Filed Under (Yamaha) by admin on 19-01-2012

download
When I first started working on bike many years ago, I learned the danger of stripping the heads of Philips screws when removing or installing them on motorcycles. I remember the two worst screws were the casing side-cover aluminum screws and carburetor bowl screws. I think I tried every method of screw removal after they were stripped. Vice grips, better tipped screwdriver, hammer, drill, and other tools were used. One way I learned to remove stripped screws is to re-make the Philips head into a flathead screw. Cutting a slot in the top of the screw and then use a flat-head screwdriver to remove the screw. On some parts this technique can work, other parts and screws it may not. The Philips screws on the bottom of the V-Star carburetor bowls are VERY prone to stripping. In fact, I will not start a carburetor cleaning without new hex head screws to replace the original Philips bowl screws. Replace the bowl screws for yourself if you keep the bike, or for the next rider that will appreciate the hex-head screws when they clean the carburetors. Not many other parts on a V-Star have screws that are prone to stripping. This documentation is to help riders with motorcycle maintenance. Some riders will find themselves with the problem of removing stripped screws. A carburetor cleaning can quickly double in time when you realize the hardest part of the job is removing bowl screws after they strip. And then realizing you do not have the replacement hex-head screws available and must now go to the hardware store.

Incoming search terms:

Kawasaki KLX450R Dual Sport Kit Installation And Removal Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the seat, fuel tank, and side panels. 2. Unplug and remove the stock headlight. 3. Taillight Installation: The Baja Designs taillight will run in conjunction with the stock taillight for this installation. Start by removing the first wire guide that the stock taillight wires pass through near the end of the fender. Once removed, trim off the remaining molded mounting boss as shown in Photo 1. Drill three ¼” holes in the fender and use the provided countersunk mounting hardware to attach the Baja Designs taillight as shown in Photo 2. The rear edge of the LED cluster should line up with the rear edge of the fender. Route the wires forward between the plastics to the left of the front mounting bolt. We’ll attach them in a later step. Photo 1 Molded mounting boss removed Stock taillight Photo 2
4. Turn Signal Installation: Drill a 7/16″ hole in each side of the fender plastic in the locations shown in Photo 3. Install the rear turn signals and route the wires forward as shown in Photo 4. Photo 3 Photo 4 Zip-tie BD taillight wires to fender here Route left signal wires through fender with stock taillight wires 5. Brakelight Switch: The KLX uses a hydraulic operated switch to activate the brakelight. Installation of this switch requires bleeding the rear brake system. If you do not feel competent performing this task please refer it to a qualified mechanic. An improperly bled brake can lead to rear brake failure. Caliper Guard Modification: The hydraulic brakeswitch replaces the banjo-bolt that attaches the rear brake hose to the caliper. Because of its larger size, the plastic caliper guard must be relieved slightly to provide clearance. Remove the caliper guard and modify as shown in Photo 5.

2001-2003 XV16 Fuel Pump and Carburetor Removal

0

Filed Under (Yamaha) by admin on 31-12-2011

download
Disconnect the carburetor fuel line hose at the fuel pump. •Disconnect the fuel pump wire coupler. •Remove the choke cable from fuel pump bracket. •Remove the upper engine mount, leaving the fuel pump attached to the mount. •Disconnect the TPS and carburetor wire couplers.       Disconnect the throttle cables, and then remove the carburetor. NOTE: The idle adjuster can be removed from its bracket without loosening the bracket screws. PAGE 3 of 12 HIDDEN 6mm SCREW 6mm BOLT UPPER ENGINE MOUNT/ FUEL PUMP CARBURETOR PAGE 4 of 12 Right-Hand Footrest Removal: •Disconnect and remove the brake light switch. •Remove the forward-most tie wrap around the brake hose and frame. •Remove the footrest assembly. NOTE: Leave the brake hose attached. Move the hose to the underside of the foot rest mount and support it as necessary so that it is out of the way Cylinder Head Oil Pipe Removal/ Installation: •Slightly loosen all three banjo bolts before removing them to prevent oil line deformation. NOTE: When loosening the upper banjo bolts, hold the line in place using a wrench at the flat surface on the fitting. Air Injection System (AIS) Removal: •Remove the electric starter motor. •Remove the regulator/rectifier assembly. Remove the AIS pipes from the cylinder head, but leave them attached to the AIS assembly. •Remove the three screws with 8mm heads, and then remove the AIS air filter from the right side. •Remove the three Phillips head screws holding    the AIS assembly on the frame. •Remove the AIS assembly from the left side. FOOTREST ASSEMBLY UPPER BANJO BOLT AIS AIR FILTER AIS ASSEMBLY
PAGE 5 of 12 Transfer Case Removal: •Remove the transfer case bracket first. Then remove the outer chrome cover, inner cover, and drive-sprocket nut. NOTE: There is a sealing washer between the inner case and the transfer case at the 8mm stud. Be sure to replace it during re-assembly. •Remove the two chrome oil lines between the engine and oil tank. NOTE: Retain the four O-rings for re-use. •Remove the drive pulley cover and remove the drive pulley nut. •Loosen the drive belt tension. •Remove the drive pulley, inner cover, collar, and O-ring. NOTE: The collar has a bevel on its inside diameter     for the O-ring facing inward and a bevel on the outside diameter facing the pulley. •Remove the drive and driven sprockets with chain as an assembly. •Remove the collar and O-ring. NOTE: Collar has a bevel on its inside diameter that faces inward for the O-ring. •Remove oil tank filler neck. •Remove the relay bracket on the right-hand side. NOTE: Leave the relays connected. Simply move them out of the way to allow room for transfer case removal. •Slide the transfer case out from the right side.

Incoming search terms:

Suzuki GSX1400FE CHASSIS REMOVAL AND INSTALLATION

0

Filed Under (Suzuki) by admin on 17-12-2010

download
REMOVAL SEAT Remove the seat with the ignition key. FRAM COVERS Remove the seat. (*Above) Remove the frame cover mounting secrews (left and right sides). Remove the frame covers by pulling on the hooked parts. PILLION RIDER HANDLE Remove the pillion rider handle by removing the pillion rider handle mounting bolts. SEAT TAIL COVER Remove the seat. (*Above) Remove the pillion rider handle. (*Above) Remove the seat tail cover mounting screws. : hooked part 6-4 CHASSIS Remove the fasteners.(*6-5) Disconnect the seat lock cable A. Disconnect the brake light/taillight lead wire coupler. Remove the seat tail cover. REMOUNTING Remount the seat, frame covers, pillion rider handle and seat tail cover in the reverse order of removal. www.GSX1400FE.co.uk
CHASSIS 6-5 FASTENER REMOVAL AND REINSTALLATION FASTENER REMOVAL Depress the head of fasteners center piece 1. Pull out the fastener. INSTALLATION Let the center piece stick out toward the head so that the pawls 2 close. Insert the fastener into the installation hole. NOTE: To prevent the pawl 2 from damage, insert the fastener all the way into the installation hole. Push in the head of center piece until it becomes flush with the fastener outside face.

Suzuki B-King GSX1300 BK Suspension Removal and Installation

0

Filed Under (Suzuki) by admin on 01-12-2010

download
Front Fork Removal and Installation B823H12206002 NOTE The right and left front forks are installed symmetrically and therefore the removal procedure for one side is the same as that for the other side. Removal 1) Remove the front wheel assembly. Refer to “Front Wheel Assembly Removal and Installation in Section 2D (Page 2D-4)”. CAUTION ! •Make sure that the motorcycle is supported securely. •Do not operate the front brake lever with the front wheel removed. 2) Disconnect the brake hose clamp (1) from the front fender. 3) Disconnect the brake hose (2) from the brake hose clamp. 4) Remove the front fender by removing the bolts (3) , left and right. 5) Remove the reflex reflector for E-03, 24, 28, 33. 6) After removing of the headlight cover upper screws (4), move the headlight assembly forward. 7) Loose the front fork upper clamp bolt (5). NOTE •Slightly loosen the front fork cap bolt (6) to facilitate later disassembly. •Be sure to adjust the rebound damping force adjuster (7) to the softest position before removing the front fork. 8) Loosen the front fork lower clamp bolts (8) and remove the front fork. NOTE Hold the front fork by the hand to prevent sliding out of the steering stem. Installation 1) Set the front fork to the front fork lower bracket temporarily by tightening the lower clamp bolts (1) . 2) Tighten the front fork cap bolt (2) to the specified torque. Tightening torque Front fork cap bolt (a): 23 N·m (2.3 kgf-m, 16.5 lb-ft) 3) Loosen the lower clamp bolts. 4) Set the front fork with the upper surface “T” of the outer tube positioned 3.0 mm (0.12 in) “a” from the upper surface of the steering stem upper bracket. 5) Tighten the front fork lower clamp bolts (1). Tightening torque Front fork lower clamp bolt (b): 23 N·m (2.3 kgf- m, 16.5 lb-ft) 6) Tighten the front fork upper clamp bolt (3). Tightening torque Front fork upper clamp bolt (c): 23 N·m (2.3 kgf- m, 16.5 lb-ft

HARLEY DAVIDSON HEATED HAND GRIP KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
REMOVAL Preparation To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow the instructions given to remove the main fuse. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. Remove the fuel tank according to the service manual instructions. -J04259 1 of 8 Left-Side Grip Removal 1. See Figure 1. Using a T-25 TORX drive head, remove the upper and lower switch housing screws (1). 2. Using a T-27 TORX drive head, loosen the upper screw securing the handlebar clamp (3) to the clutch lever bracket. Remove the lower clamp screw with flat washer. Loosen the clamp and position the clutch hand lever assembly away from the switch housing. Separate the upper and lower switch housings. 3. With “glueless” grip: Remove the grip from the handlebar. With glued grip: Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. 2 2 1 5 4 3 1 is01283 1. Switch housing screws 2. Grooves 3. Handlebar clamp 4. Left handlebar grip 5. Larger diameter of flange Figure 1. Left Handlebar Switch Housing Right-Side Grip Removal Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) NOTE A section of corrugated cardboard or the eyelet of an ordinary cable strap can be used for this purpose. See Figure 2. 1. Place a 5/32-inch (4 mm) thick insert between the brake lever and the lever bracket. 2. Using a T-25 TORX® drive head, remove the upper and lower switch housing screws. 3. Using a T-27 TORX drive head, loosen the upper screw securing the handlebar clamp to the brake master cylinder housing. Remove the lower clamp screw with flat washer. Loosen the clamp and position the master cylinder assembly away from the switch housing. Separate the upper and lower switch housings. 4. Remove the grip from the handlebar. NOTES The twist grip sensor in the right side of the handlebar has a seal cap that protects internal electrodes from dirt and moisture, and also serves as a retention device for the throttle grip. To remove the grip, a slight tug may be necessary to release the index pins in the grip from the receptacle in the seal cap. Upon removing the grip, check the location of the seal cap. If the seal cap is still fastened to the index pins inside the old throttle grip, it can be discarded along with the grip. If the seal cap is still fastened to the end of the twist grip sensor: •See Figure 3. Insert a small screwdriver or other flat-blade tool into the flat area on one side of the seal cap. •Press the leg on the underside of the cap to free it from the slot at the end of the twist grip sensor. Pry up one end of the cap. •Repeat on the other side of the cap. •Carefully remove the cap and discard it

Incoming search terms:

HARLEY DAVIDSON LOCKING FUEL FILLER CAP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION 1. Prior to installing the gas cap on the vehicle, insert the key into the lock. Firmly grasp the chrome top of the fuel cap and turn the key until it stops. On right hand threaded fuel caps, turn the key counter-clockwise until it stops. On left hand threaded fuel caps, turn the key clockwise until it stops. This assures an unlocked position for the gas cap. Allow the key to return to the neutral position. 2. Remove the key and install the fuel cap on the vehicle. is00770 Figure 1. Right Hand Threaded Fuel Cap Installation NOTE When installing the fuel cap, rotate the cap one full turn past the audible click. This automatically positions gas cap to lock position. A properly locked/installed gas cap will rotate freely in both directions. Failure to do so will give an incorrect assumption that the fuel cap does not work properly. REMOVAL On right hand threaded fuel caps, insert key, and while holding the gas cap in place with hand, turn key counterclockwise until it stops, return key to original position. Gas cap must rotate 270 degrees counter-clockwise before mechanism engages to allow gas cap removal. Continue to rotate counterclockwise to fully remove gas cap. On left hand threaded fuel caps, insert key and while holding the gas cap in place with hand, turn key clockwise until it stops, return key to original position. Gas cap must rotate 270 degrees clockwise before mechanism engages to allow gas cap removal. Continue to rotate clockwise to fully remove gas cap. REPLACEMENT KEYS Record the 4 digit key number stamped on the back of the key opposite the Harley-Davidson logo, in the area provided below. If a replacement key is needed, see your Harley-Davidson Dealer with the 4 digit number to order a replacement

Incoming search terms:

Harley-Davidson FLOATING BRAKE ROTOR (DISC) KITS Removal and Disassembly

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. Models WITHOUT maxi-fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. NOTE For 2004 and later XL (Sportster®) models, the negative battery cable is most easily disconnected at the engine crankcase . Removal and Disassembly 2. Refer to FRONT WHEEL: REMOVAL or REAR WHEEL: REMOVAL in the Service Manual, and follow the instructions to remove the wheel from the motorcycle. Use a TORX® drive head to remove the screws retaining the currently installed brake disc to the wheel. The brake disc and screws can be discarded. 3. Inspect the wheel bearings per the PRELIMINARY INSPECTION instructions in the appropriate WHEEL section. Follow the DISASSEMBLY and CLEANING AND INSPECTION instructions as necessary to properly service the wheel. Reassembly and Installation Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 4. Refer to WHEEL: ASSEMBLY in the Service Manual, and follow the instructions to install the new brake disc to the wheel, using the new TORX screws from the kit. Complete the ASSEMBLY instructions as necessary to service the wheel. 5. Refer to WHEEL: INSTALLATION in the Service Manual, and follow the instructions to re-install the wheel to the motorcycle. Return to Service 6. Verify that the Ignition/Light Key Switch is turned to the OFF position. 7. Models WITH maxi-fuse: Refer to the Service Manual and follow the instructions given to re-install the maxi-fuse

HARLEY DAVIDSON MULTI-FIT BRAIDED THROTTLE/IDLE CABLE KITS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Disconnect battery cables, negative (-) cable first or remove the main fuse following the instructions in the service manual. NOTE When performing cable disassembly procedures, make careful notes as to the existing cable routing. Pay special attention to existing cable strap locations before removing so new straps can be installed in the same locations. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 2. See Figure 1. Place the cardboard insert between the brake lever and lever bracket. 3 2 1 is00825 1. Brake lever 2.5/32 inch (4 mm) cardboard insert 3. Brake lever bracket Figure 1. Install Cardboard Insert 3. See Figure 2. Loosen cable adjuster jam nuts. Turn cable adjusters in until they are as short as possible. This will provide enough slack for easy removal. 3 4 1 2 5 is 02071 1. Upper switch housing 2. Lower switch housing 3. Throttle cable adjuster 4. Idle cable adjuster 5. Adjuster jam nut Figure 2. Handlebar Throttle Control 4. Remove the right upper and lower switch housing screws. 5. Loosen the upper screw securing the handlebar clamp to the master cylinder housing. Remove the lower clamp screw and flat washer. NOTE If possible, leave the friction shoe in place. The friction shoe is a loose-fit and may fall out or become dislodged if the lower switch housing is turned upside down or shaken. 6. See Figure 3. Remove the brass ferrules from the notches on the inboard side of the throttle control grip. Remove the ferrules from the cable end fittings. 1 2 4 3 is 02072 1. Throttle cable 2. Idle cable 3. Brass ferrule 4. Notch Figure 3. Throttle/Idle Control Cables 7. Pull the crimped inserts at the end of the throttle and idle control cable housings from the lower switch housing. For best results, use a rocking motion while pulling. Remove cables with retaining rings from switch housing. Apply a drop of light oil on the retaining ring, if necessary, to help in removal. NOTE If installing different handlebars, measure the change in distance that will be required from the end of the cable housing to the throttle grip. Compare this additional required length to the cables provided in the kit. If the cables are more than 2.0 inches (51 mm) longer or more than 1.0 inch (25 mm) shorter than the above measured distance, see a Harley-Davidson dealer for the correct cable length. Install proper length throttle cables. Incorrect cable length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00396b) 8. Follow instructions in the applicable service manual and remove air cleaner and backplate.

Incoming search terms:

HARLEY DAVIDSON FLAME HANDLEBAR GRIPS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
REMOVE AND INSTALL THE LEFT GRIP 1. See Figure 1. Using a T27 TORX® drive head, remove the two screws with flat washers securing the handebar clamp (3) to the clutch lever bracket. Remove the clamp and position the clutch hand lever assembly away from the handlebar 2. Using a T25 TORX® drive head, loosen but do not remove the upper and lower switch housing screws (1). 3. Remove the end cap from the existing left handlebar grip if so equipped. Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. Do not lubricate left handlebar grip before installation. Lubricating grip can cause it to come off while riding, which could result in loss of control and death or serious injury. (00315a) NOTE Make sure that the handlebar surface and the inside of the grip are smooth, dry and thoroughly cleaned of all dirt or adhesive residue. 4. Position the new left grip (4) so the larger flange (5) is at the bottom. Push the grip fully onto the handlebar. 5. Fit the grooves (2) on the outboard side of the upper and lower switch housing over the flanges on the end of the grip, then loosely fasten the two screws. 6. Position the clutch hand lever assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the bottom of the clutch lever bracket. 7. Align the holes in the handlebar clamp with those in the clutch lever bracket, and loosely fasten the two screws with flat washers. Adjust the switch housing and clutch hand control position for rider comfort. 8. Using a T27 TORX® drive head, tighten first the upper, then the lower handlebar clamp screws to 60-80 in-lbs (6.8-9 Nm) . 9. Using a T25 TORX® drive head, tighten first the lower, then the upper switch housing screws to 35-45 in-lbs (4- 5.4 Nm) . 5 3 1 1 4 2 2 is00735 1. Switch housing screws 2. Grooves 3. Handlebar clamp 4. Left handlebar grip 5. Larger flange Figure 1. Left Handlebar Switch Housing REMOVE AND INSTALL THE RIGHT GRIP NOTE Right handlebar switch removal requires a Service Manual for your model and year of motorcycle. A Service Manual can be purchased from your Harley-Davidson Dealer. 1. Refer to the RIGHT HANDLEBAR SWITCH section of the Service Manual for removal of the switch housing assembly. This is necessary to access the throttle cables. 2. Refer to the THROTTLE CONTROL section of the Service Manual to disconnect the throttle cables and remove the existing right grip/throttle sleeve assembly. After removal, make sure that the handlebar end is clean and smooth. 3. Follow instructions in the Service Manual to install the new right grip/throttle sleeve to the handlebar and connect the throttle cables. 4. Verify that the right grip/throttle sleeve rotates and returns freely and does not bind on the handlebar or switch housing.

Incoming search terms:

Incoming search terms: