softail swingarm removal

You search Auto repair manual PDF softail swingarm removal, if there are search results will appear below. If search results do not exist, please search by others keyword.



  softail swingarm removal Direct Download speed 5282 Kb/s

  softail swingarm removal Full Version speed 6162 Kb/s



HARLEY DAVIDSON SOFTAIL SWINGARM PIVOT COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-04-2011

download
INSTALLATION 1. Use rubbing alcohol to clean the swingarm surface, pivot bolt, and nut. 2. Place the larger left-side pivot cover (3) over the pivot nut. Position the set screw (4) at the bottom of the cover. Tighten set screw to 16 in-lbs (1.8 Nm) . 3. Remove adhesive backing from and apply the left-side trimplate to the swingarm. Apply pressure to the trimplate on the swingarm for one minute. 4. Remove adhesive backing from and apply an emblem to the center of the pivot cover. Apply pressure to the emblem for one minute. 5. Repeat Steps 1-4 for the right side of the swingarm. 6. Allow adhesive to cure for 24 hours before operating the vehicle. SERVICE PARTS 4 2 5 3 1 5 6 3 is01811 Figure 1. Service Parts: Swingarm Pivot Cover Kit Table 1. Service Parts: Swingarm Pivot Cover Kit Part Number Description (Quantity) Item Not Sold Separately Right-side trimplate and adhe- sive 1 Not Sold Separately Left-side trimplate and adhesive 2 Not Sold Separately Adhesive emblem (2) 3 Not Sold Separately Left-side pivot cover 4 3231B Set screw (2) 5 Not Sold Separately

Incoming search terms:

240 tire V-Rod kit for stock swingarm Installation Instructions

0

Filed Under (Harley Davidson) by admin on 27-11-2010

download
Recommended Parts and Supplies 1. Sawzall or comparable cutting tool. 2. Cut-off tool or jigsaw. 3. Shop or repair manual 4. Shop supplies, (loctite-red and blue, anti-seize, etc.) 5. Assorted hand tools. 6. 4-1/2″ grinder. 7. Drive pulley seal HD part # 11354K (qty.1) 8. Copper cap locking plate HD part # 35451-01K (qty.1) (The seal and locking plate can be re-used if not damaged during removal) Stock component removal To install the 240 kit, it will be necessary to raise the motorcycle off the ground on a suitable lift. WARNING – Be sure to center the motorcycle on the lift so that it does not fall over when you raise it up or when you are working on it. Installation of the 240 kit begins with the disassembly and removal of the rear end of the bike. Start with the simplest and most obvious components. For detailed information on removal of these parts, consult your factory manual. 1. Remove rear wheel assembly and brake. 2. Remove swingarm. 3. Cut brake tab on swingarm (as pictured). 4 4. Clean up casting mark on inside of swingarm in pulley area (as pictured). 5 5. Remove and replace right side swingarm mount with mount included in kit. 6. Install swingarm with new supplied pivot shaft. 7. Install stock spacer on left side of shaft, use supplied stepped spacer between stock spacer and swingarm. (Small step toward bearing). 8. Remove front pulley, and disassemble. 9. Test fit ½” allen bolts in hub before removal. Some models require drilling for bolts to fit. If necessary, use ½” bit and drill before removing, minimal material will be removed. Take caution not to drill too deep and hit case. 6 10. Install supplied adapter on the back to space pulley out. (Use loctite on bolts, and assemble as pictured).

Incoming search terms:

YAMAHA SINGLE SIDED SWINGARM REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Yamaha) by admin on 27-12-2011

download
1. Disconnect Battery 2. Lift and secure bike 3. Remove brake-side floorboard 4. Remove exhaust. 5. Remove rear fender 6. Remove front pulley cover 7. Remove wheel, pulley, and brake assembly simultaneously. Now remove front pulley from transmission. (Keep up with the stock nut and lock washer; these will be used during assembly) 8. Remove Passenger pegs; now remove the plastic covers in the frame that cover the pivot tube bolts. 9. Remove the stock shock bolts ( keep for re-assembly) 10. Remove the pivot tube bolts. 11. Remove the stock swingarmb12. Install “new” belt at this time. 13. Install supplied pivot tube, and bearings in RC swingarm. 14. Install shock bolt with red loctite in RC swingarm. (Do not tighten bolt at this time) 15. Insert supplied pivot bolts with red loctite through frame and supplied bushings into the RC swingarm. (Right side bushing has flats) 16. Torque shock and pivot bolts to factory specs. 17. Install belt adjustment bolts and single side keys into swingarm.

Suzuki 240 Hayabusa Swingarm Installation Instructions

0

Filed Under (Suzuki) by admin on 12-02-2012

download
installation Instructions 1.) Stock Component Removal To begin installing this kit it is necessary to raise the rear end of the bike using a suitable hoist. Be sure to keep the bike centered on the front wheel to keep the bike from tipping over. Once you have the bike lifted and properly secured, begin with the removal of the following stock components ( For detailed information on the removal of these parts, please consult your factory manual) : 1.) Muffler or mufflers 2.) Left side and lower body panels 3.) Voltage regulator (08 model only) 4.) Front sprocket cover 5.) Front sprocket 6.) Chain 7.) Rear Axel, wheel and brake assembly 8.) Pivot tube and swingarm
2.) New Swingarm Installation A. Most of the pieces needed are installed on the swing-arm. You’ll need to install the shock mount block with the 4 supplied flat head 5/16″bolts, use red loctite and torque to 25 ft lbs. B. Insert the 2 supplied pivot bushings in the pivot tube. Move your new swingarm into position. Once you have the swingarm in position reinsert the pivot tube to hold it in place. C. On some bikes (07′ and earlier Busa’s) it is necessary to grind approximately 1/8″ off the frame for chain clearance. Not all bikes will require this, but it is best to mock up and test fit before final assembly.

HARLEY-DAVIDSON SOFTAIL CROSSOVER REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-04-2012

download
EXHAUST SYSTEM REMOVAL READ ALL INSTRUCTIONS BEFORE BEGINNING 1. Under the oil tank on the right hand side, locate the rear O² sensor connector. Unplug sensor and feed the end of wire through the frame freeing it from motorcycle. NOTE: Pay attention to wire routing for re-installation. 2. Open the plastic cover above the rectifier on front of the frame to access to the front O² sensor connector. Unplug sensor from harness. Remove ZIPSTRIP holding wire to frame and feed the wire through freeing it from motorcycle. 3. On floorboard equipped models, loosen the right hand floorboard mounting bolts to gain clearance for exhaust removal and installation. 4. Loosen the heat shield clamps on both front and rear exhaust pipes. 5. Remove the mounting nuts from each head pipe, located at the cylinder head. 6. Remove the nuts attaching the exhaust mount bracket to the frame. 7. On FLSTD and FLSTF models, you will need to remove the right side passenger foot peg and hanger, as this is attached to the exhaust mount bracket. Replace the passenger foot peg assembly using the BOLT 14 Allen bolt (supplied). 8. Remove the entire exhaust system and set it aside. 9. Remove the two lower mounting studs from the frame See figure 1 . Recommended replacement exhaust port gaskets, H-D P/N: 65324-83A. 10. Carefully remove exhaust port flanges and circlips from the stock exhaust system using snapring pliers. See figure 2 . NOTE: Replace bent or damaged circlips. Check exhaust port gasket condition. 11. Remove O² sensors from stock head pipe and set aside for re-installation on your new RUSH exhaust system. PAGE 1 OF 4 RUSH RACING PRODUCTS EXHAUST SYSTEM INSTALLATION P/N 7020 – 7120 BEFORE INSTALLATION PLEASE READ ALL INSTRUCTIONS 1. Remove header and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark outside edge of each heat shield to show location of mounting clips that hose clamps will loop through See figure 3. 2. Apply a small amount of anti-seize compound to the threads of the O² sensors and install them into the new head pipe. NOTE: Be careful not to get anti-seize on sensor tip, it may affect sensor function. 3. Install circlips and flanges from stock system onto the new head pipe See Figure 2. Note: Replace circlips if bent or damaged 4. Attach BRKT-007 to frame using two BOLT 12 Tighten to factory specs. 5. Install complete assembly into exhaust ports (rear port first). Use stock flange nuts, Do Not Tighten .

Incoming search terms:

HARLEY DAVIDSON SOFTAIL Shortshot Exhaust System REMOVAL AND INSTALLATION

0

Filed Under (Harley Davidson) by admin on 17-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. On FLSTC, FLSTF, FLSTN and FXSTS loosen the right hand floor board mounting bolts to gain clearance for exhaust removal and installation. 2. Loosen the heatshield clamps on both front and rear exhaust pipes. 3. Loosen the crossover pipe clamp, located between the front and rear head pipe. (This step is not necessary on 2000 models). 4. Remove the two mounting nuts from each head pipe, located at the cylinder head. 5. Remove the bolts that attach the mufflers to the frame. 6. Remove the entire exhaust system and set it aside. 7. On pre 2000 models remove the lower mounting bar. 8. FLSTN, FLSTF and FXSTD models have an upper mounting bar that must be removed in addition to the lower bar. 9. Park the motorcycle on its side stand. Remove the right side 1/4″-20 bolt which holds the lower fender in place. The fender will flex out of the way allowing the removal of the right passenger foot peg bolt. Position a floor jack under the right hand frame tube of the motorcycle below the swing arm pivot bolt. Raise the jack just enough to take the weight off the pivot bolt and remove the bolt and stock mounting bar. Set the mounting bar aside. Replace the pivot bolt and torque it between 120 -150 ft. lbs. Reinstall the passenger foot peg using the 1/2″-20 x 3″ bolt and an 1 5/8″ long spacer (supplied). 10. On 2000 year models, using a #50 Torx driver, remove the three mounting bolts, and set the mounting bar aside. (Two of the bolts are visible, the third is accessed by removing the right hand passenger foot peg.) Replace the foot peg using the 3/8″-16 x 2 1/2″ bolt and 3/4″ length spacer (supplied). 11. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. NOTE: If circlips look bent or twisted replace them with new circlips. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Vance and Hines recommends you replace your exhaust gaskets with Sceamin’ Eagle gaskets part number 17048-98. 2. Install the mounting bracket to the frame, by aligning the two 3/8″ holes in the bracket with the two holes in the frame below the right rear footrest, using the two 3/8″-16 x 3/4″ flange head bolts (supplied), do not tighten at this time. When the bracket is mounting correctly, it should bend out and away from the motorcycle, with the four holes of the bracket toward the front of the motorcycle. 3. Install the circlips and flanges from the stock system on to both of the new head pipes

Incoming search terms:

HARLEY DAVIDSON SECURITY SYSTEM SMART SIREN KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
REMOVAL 1. Refer to the owner’s manual and follow the instructions to disarm the security system. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. For All Models except 2002-2003 Touring and 2003- Later Softail: Refer to the owner’s manual and follow the instructions to disconnect the battery, negative (-) cable first or remove the main fuse. For 2002-2003 Touring and 2003-Later Softail Models: Remove seat following the instructions in the service manual and disconnect the battery, negative (-) cable first. Save seat hardware for installation. INSTALLATION 2002-2006 VRSCA, VRSCB, VRSCD Models 1. Open the seat. 2. See Figure 1. Remove the splash guard (mud flap) nuts. 3. See Figure 2. Lower the mud flap from the installed position and allow it to rest on the rear tire 3. Slide the siren into place on the left side of the electrical caddy so the sounder disc (6) faces out. 4. Refer to the owner’s manual and follow the instructions to install the main fuse. 5. Align the barbed studs on the side cover with the grommets in the frame and push side cover firmly into place. 6. Install the left side saddlebag per the instructions in the owner’s manual. 2003 and later Softail Models EXCEPT FXCW/C 1. Remove the right side saddlebag (if equipped) per the instructions in the owner’s manual. NOTE The siren connector is installed on an electrical panel under the rear fender on all Softail models. The rear of the motorcycle may have to be raised slightly to allow removal of the splash guard. 2. Remove the two bolts at the bottom of the splash guard. Bend the upper right corner of the splash guard toward the rear tire and lift upward to unhook the splash guard from the tab on the rear fork. Remove the guard from beneath the fender. 2 1 3 is01316 1. Siren mounting area 2. Siren connector [142B] 3. Harness clip Figure 16. Siren Connector (Softail Models EXCEPT FXCW/C) (Rear Fender View with Rear Wheel Removed) 3. See Figure 16. Remove the siren connector [142B] (2) from the receptacle in the siren mounting area (1) of the electrical panel. 4. See Figure 17. Insert security siren (1) connector [142B] into the siren box receptacle until the connector latches securely. 5. Orient the siren (1) as shown, with the harness connector (2) toward the bottom and the sounder disc (5) facing out. Carefully snap the siren into the electrical panel. 6. Insert the siren harness lead (4) into the harness clip (3) to keep the harness clear of other components. 7. If necessary, secure the connector wiring to the electrical panel wiring with a cable strap (not provided). 8. Hook the slot at the top of the splash guard over the tab on the rear fork and install the guard with the two screws removed earlier. Tighten securely. 9. Install the right side saddlebag (if equipped) per the instructions in the owner’s manual. 10. Refer to the owner’s manual and follow the instructions given to connect the battery cables or install the main fuse

Incoming search terms:

HARLEY DAVIDSON SOFTAIL 6 SPEED TRANSMISSION – COMPLETE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-04-2011

download
Removal of Original Transmission 1. Position motorcycle on a suitable lift. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. 3. Refer to the TRANSMISSION CASE REMOVAL in the Service Manual and follow the instructions given to remove the components with the following steps. 4. Refer to PRIMARY CHAINCASE COVER REMOVAL in the Service Manual and follow the instructions given to remove the primary chaincase cover. Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) 5. See the PRIMARY CHAIN and COMPENSATING SPROCKET REMOVAL in the Service Manual and use the instructions given to remove the primary drive assem- bly. 6. Refer to the STARTER REMOVAL in the Service Manual and remove the the starter. 7. See the VEHICLE SPEED SENSOR section and unplug the vehicle speedometer sensor connection and remove the mounting bolt. Lift sensor from the transmission case and set aside for later re-installation. 8. Refer to NEUTRAL SWITCH and disconnect the connectors from the neutral switch. 9. Refer to PRIMARY CHAINCASE in the Service Manual and follow the instructions given to remove the primary chaincase housing. 10. Refer to EXHAUST SYSTEM in the Service Manual and remove the exhaust. 11. See the REAR WHEEL REMOVAL and loosen but, do not remove rear axle to relieve drive belt tension and remove the belt from the sprocket from the transmission. 12. Refer to OIL TANK REMOVAL in the Service Manual and follow the instructions given to drain, remove the oil tank and detach the vent, feed and return lines. 13. Refer to CLUTCH CONTROL in the Service Manual and follow the instructions given to remove the clutch cover and disconnect the clutch cable end from the cover. Set the cable aside for later re-installation

Incoming search terms:

HARLEY DAVIDSON REAR SWINGARM AXLE COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) NOTE XL Sportster 883 and XL1200R models may require loosening or removal of the rear muffler in order to install the right side rear axle cover. See the EXHAUST SYSTEM REMOVAL section of the Service Manual. 1. Support the vehicle, and loosen or remove the rear muffler if necessary. XL Sportster 883 and XL1200R models: Remove the right-side lower shock absorber mounting bolt. Save for re-installation. All other models: Remove and discard the right-side lower shock absorber mounting bolt. 2. Swing the bottom of the shock absorber out of the way. Position the right-side swingarm axle cover (2) over the swingarm and behind the shock absorber. 3. Reposition the shock absorber. XL Sportster 883 and XL1200R models: Install the shock absorber mounting bolt removed in Step 1. All other models: Install the shoulder bolt (3) from the kit. All models: Tighten the bolt to 45-50 ft-lbs (61-68 Nm) . NOTE When torquing the bolt, align two of the bolt-head flats parallel to the ground. This will allow proper orientation of the bar and shield logo on the bolt cover. 4. Position the bolt cover (4) over the bolt head (3) with the Bar-and-Shield logo oriented upright, and lock in place with the set screw (5). Tighten securely. Reposition and tighten the muffler per the Service Manual instructions. 5. Remove and discard the left-side lower shock absorber mounting bolt. Move the bottom of the shock absorber out of the way. Position the left-side swingarm axle cover (2) over the swingarm and behind the shock absorber. 6. Reposition the shock absorber and install the shoulder bolt from the kit. Tighten to 45-50 ft-lbs (61-68 Nm) , aligning two of the bolt head flats parallel to the ground. 7. Position the bolt cover over the bolt head with the Bar-and- Shield logo oriented upright, and lock in place with the set screw. Tighten securely

Incoming search terms:

2007 Softail HARLEY DAVIDSON FUEL PUMP/ FUEL GAUGE SENDING UNIT REMOVAL AND INSTALLATION

0

Filed Under (Harley Davidson) by admin on 30-03-2012

download
1. Remove seat. 1 WARNING 1 WARNING To prevent spray of fuel, purge system of high-pressure fuel before supply line is disconnected. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00275a) 2. Purge the fuel supply line of high pressure gasoline. a. See Figure 4-36. Disconnect the fuel pump fuse from the main wiring harness. b. Start the engine and allow the vehicle to run. c. When the engine stalls, operate the starter for 3 seconds to remove any remaining fuel from the fuel lines. 1 WARNING 1 WARNING To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 3. Disconnect negative battery cable. 4. Remove instrument console. a. All but FXSTD, see Figure 4-37. Remove acorn nut and washer on instrument console to separate console from fuel tank. b. For FXSTD, see 8.26 INSTRUMENT CONSOLE: FXSTD. 5. Disconnect console wiring. Figure 4-36. Fuel Pump Fuse: View From Top Figure 4-37. Acorn Nut And Washer: All But FXSTD s0660x8xx 7526
4-28 2007 Softail: Fuel System HOME 1 WARNING 1 WARNING Gasoline can drain from the crossover line when disconnected from fuel tank. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00259a) 6. Drain fuel tank. a. Obtain a short section of hose (5/16 inch I.D.). Insert bolt in one end of hose and install hose clamp to ensure that end is securely plugged. b. See Figure 4-38. Cut clamp (1) from one end of crossover hose (2). Quickly replace crossover hose on fuel tank fitting with open end of short hose while directing flow of gasoline from free end of crossover hose into suitable container. 7. See Figure 4-39. Unplug fuel pump module connector (3) [86]. 8. Remove top plate screws (2) and discard. 9. See Figure 4-40. Pull top plate (2) out of fuel tank enough to expose fuel hose and clamp (1). CAUTION Carefully inspect end of hose for cuts, tears, holes or other damage. Replace hose if any damage is found. Even the smallest hole can cause a reduction in fuel pressure. 10. Cut clamp and remove hose from regulator housing fit- ting.

Incoming search terms:

Incoming search terms: