solar collectors mail

You search Auto repair manual PDF solar collectors mail, if there are search results will appear below. If search results do not exist, please search by others keyword.





Kawasaki ZRX-1100 / 1200 exhaust system Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the existing exhaust system and save the flange nuts for reuse. Save the stock exhaust can mounting bolt and nut for reuse as well. 2. Inspect the exhaust gaskets. Replace if necessary. 3. Attach the head pipes 1, 2, 3 , and 4 to the exhaust ports of their respective cylinders, using the flange nuts saved from step 1 above. Loosely apply the flange nuts for now, allowing for ome adjustment. 4. Attach the Y-pipe collectors to the head pipes. Please note that one collector goes to pipes #1 and #4 and one collector goes to pipes #2 and #3 (collectors are labeled). Make sure the ends of the head pipes fit flush and snug in the ports. Do not install the springs at this time. 5. Install the S-Bend to the rear of the two Y-pipe collectors. Do not install the springs at this time. 6. Go back and retighten the head pipe flange nuts per factory specifications – make sure the head pipes are centered in each port. 7. Slide the TiForce end can into place on the S-bend pipe. 8. Loosely attach the two rubber bands, stainless steel bands K, and the stay / hanger G, to the end can using the supplied 6mm hardware H. (See figure 1) . Make sure that the rubber bands fully cover the stainless bands to prevent scratches to the can. 9. Place the bands approximately 108mm from the edge of the end can. (See figure 2) . 10. Go back and tighten the exhaust flange nuts per factory specification. Do not over tighten. 11. Using the stock provided mounting point on the right passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 12. Attach the supplied springs to all the joints, starting from the head pipes and working back to the end can. 13. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. 14. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (refer to step 11 / figure 2), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 15. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 16. Check that all hardware is properly tightened, and then start the motor and check for exhaust leaks

Incoming search terms:

1989 – Current All Mode SENSOR INSPECTION FOR AIR CONDITIONING SYSTEM REPAIR

0

Filed Under (Toyota Manuals) by admin on 30-10-2011

download
specifications. The inspection procedure for each type of sensor differs from the others. Select the appropriate inspection procedure from the table below according to vehicle specifications and perform the inspection. EQUIPPED WITH AUTOMATIC LIGHT CONTROL SYSTEM A/C SYSTEM WITH RIGHT/LEFT INDEPENDENT TEMPERATURE CONTROL INSPECTION PROCEDURE No No A No Yes B Yes Yes C Yes No D Procedure A: a. Disconnect the solar sensor connector. b. Measure the resistance between terminals 1 and 2 of the solar sensor under the following conditions: Cover the sensor with a cloth to avoid direct light. Expose the sensor to light from a distance of 300 mm (11.81 in.) or less with an inspection light. NOTE: Terminal 1 of the sensor is always on the right, when the lock is facing up. When using an analog tester, connect the positive (+) lead to terminal 2 and negative (-) lead to terminal 1 of the solar sensor. HINT: If the light is weak, the sensor may not react. Be sure to use an incandescent light for an inspection light

2010 Toyota Motorsports/ TRD USA Contingency Award Program

0

Filed Under (Toyota Manuals) by admin on 29-09-2011

download
To enroll in the program, complete the registration form included in the enclosed material and mail, fax or e-mail it to TRD per the instructions at the bottom of the form. Contact personnel are listed on the attached 2010 Contingency Award Guidelines sheets. These people are available to assist you throughout the year. Parts Ordering: If you are planning to order Toyota parts during 2010 you must supply us with your Visa or Master Card credit card number at the time you register in the program. There is a line on the registration form for this number. See the attached Parts Ordering Guidelines for detailed information on how to order parts. TRD is looking forward to working with each of you, and we wish you a very successful year with your racing program

Incoming search terms:

HONDA 2005 CBR 600 RR FULL S/S EXHAUST HEADER INSTALLATION

0

Filed Under (Honda) by admin on 01-12-2011

download
Place the motorcycle in a vise or on it’s kick stand and make sure it is safe and secure. NOTE: If reusing the stock midpipe and muffler, skip ahead to step #5. 2) Remove the rider and passenger seats. Unplug the tail light, license plate light, and turn signals wires inside the tail section. 3) Remove the four bolts that secure the tail section to the subframe. Carefully remove the tail section from the subframe. 4) Remove the four bolts that secure the license plate/turn signal mount to the subframe. Remove the mount from the motorcycle. 5) Remove the upper and lower front fairing pieces. 6) Remove the two bolts that attach the right side footpeg assembly to the motorcycle. Disconnect the rear brake light switch and swing the footpeg assembly out of the way. Remove the outer plastic foot guard. Remove the aluminum heat shield from the motorcycle. 7) If equipped, remove the o2 sensor from the stock midpipe assembly.
NOTE: If reusing the stock midpipe and muffler, loosen the midpipe mounting bolts, and loosen the clamp securing the headpipe to midpipe connection. Skip ahead to step #9 8) Remove the midpipe mounting bolt, located on the right side of the subframe. Remove the
muffler mounting bolts. Lower the muffler and remove the rear exhaust section from the midpipe. 9) Remove the eight hex flange nuts securing the header flanges to the cylinder. 10)Remove the bottom header mounting bolt from the midpipe assembly. Remove the complete header from the motorcycle. 11)Remove the hat washer and rubber grommet from the stock midpipe assembly. Install the rubber grommet and hat washer into the hole provided on the Jardine midpipe assembly. 12)Slide the four headpipes into the new collectors. The headpipes are numbered from #1 thru #4, with #1 being the furthest toward the left side of the motorcycle, then work your way to the right. Do not install the provided springs at this time

Incoming search terms:

2007 – 2009 APRILIA RSV MILLE EVOLUTION OPEN EXHAUST SYSTEM

0

Filed Under (Aprilia) by admin on 06-11-2010

download
Measurements of the Akrapovic EVOLUTION street legal system on the APRILIA RSV MILLE (with muffler insert): Power & Torque: the Akrapovic exhaust system increase the responsiveness of the Aprilia and fill out the power and torque curves. The increase in power and torque starts already at around 3000 rpm and leads all the way to the top of the rpm range. At 10300 rpm we measured a massive 129.1 HP on rear wheel and max. increase of power 9.4 HP at 10550 rpm. CONFIGURATION The Racing and Evolution systems differ only in the selection of tubing materials. The Racing is made of stainless steel, and the Evolution is made of titanium. Both systems have conical tubes, collectors, and a link pipe. All of the system components are attached with sleeve joints secured with silicon-shielded springs. The header tubes come with interference crossover tubes, and the systems also include a fitting for attaching a lambda sensor. The HEXAGONAL muffler is definitely the most eye- catching element of the system. It is made of a titanium inlet cap and perforated inner sleeve, while the outlet cap is made of carbon fiber. The outer sleeve is available in titanium or carbon fiber. The muffler is attached to the frame using an Akrapovic carbon fiber clamp. PERFORMANCE stock AKRAPOVIC max. increased power max. rear wheel power HP / rpm (measured on Dynojet ATV) 122.1 / 9740 129.1 / 10300 9.4 / 10550 interference crossover tubes YES (in collector) lambda sensor YES header tube inner sleeves – header tube flanges S.S LASER CUT header tubes – collector connection SLEEVE JOINT + SILICON SHIELDED SPRINGS collector / header tube – link pipe connection SLEEVE JOINT + SILICON SHIELDED SPRINGS link pipe – muffler connection SLEEVE JOINT + SILICON SHIELDED SPRINGS muffler inlet cap /outlet cap Ti / Carb.-fiber muffler metal interior TITANIUM muffler outer sleeve Ti / Carb.-fiber muffler clamp CARBON-FIBER muffler bracket Carb.-fiber (OPTIONAL) muffler insert EU YES heat shield YES (stock) US – catalytic converter YES (2x) CONFIGURA- TION CONFIGURATION header tubes collector link pipe material S.S. (begining) S.S. / TI (header tube) S.S. / TI STAINLESS STEEL / TITANIUM tube shape CONICAL CONICAL CONICAL Technical specifications of Akrapovic exhaust systems and related products subject to change without notice. ADDITIONAL DATA weight comparison (kg) stock AKRAPOVIC difference 12.57 S.S. link pipe TITANIUM link pipe stock – S.S. stock – titanium – 5.52

Incoming search terms:

Kawasaki ZX-14 Indy Series Exhaust System REMOVAL AND INSTALLATION

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove and place the lower fairings in a safe place, to separtate them unhook the rivet at the bottom. The right side lower fairing will need to be trimmed for proper exhaust clearance. Remove the fairing knee panels. Two rubber grommets retain the panel after bolt removal, light force is required to pull panel off. Remove the tank cover. Four rubber grommets and two plastic hooks retain the panel after bolt removal, pull outward to remove from grommets then pull forward and up, light force is required. Remove mid fairing sides. Undo pushpin located on the fairing backside. Note: Blinker connectors must be disconnected before pulling the fairing too far. Remove the left and right muffl ers. Remove the stock header. Note: Be careful not to damage the radiator while removing the stock header and installing the new header leaving the fl ange nuts loose at this time. Install both collectors 7-40020 and 7-40022 holding them to the headers install the four springs 7-30002 from the header to collector spring tabs. Install collector 7-40014 by installing two springs 7-30002 from collector to collector spring tabs. Note: A small amount of WD-40 at the pipe joints will help to fi t them together. Install the megaphone on the header assembly using one of the original muffl er mounting bolts and nuts removed in step 6, mount the megaphone to the forward muffl er mount located at the footpeg. Tighten the header nuts and then remove the megaphone. At this point the right side lower fairing needs to be trimmed. A template is supplied (Page 4) to outline the clearance cut that is needed on the right side lower fairing, we recommend using a dremel tool or a die grinder. The template should give you the necessary clearance but some fi tments may vary. After making the cut lightly sand the edges being careful not to scratch the paint. Clean all fi ngerprints from the exhaust using contact cleaner (or other non fl ammable cleaner). Fingerprints will leave stains on the pipe once the motorcycle is started. Try a test fi t. If you feel more clearance is needed, mark the fairing and remove it, trim until there is at least a 1/4″ of clearance. Reinstall the megaphone and check that the O2 plug is tight. You are now ready to start your motorcycle. Check for exhaust leaks and oil leaks. Shut off the bike and re check the oil level

Repair Manual Supplement : Vehicle Pulling to One Side Suspension

0

Filed Under (Toyota Manuals) by admin on 20-10-2011

download
2002-2009 4Runner, Avalon, Camry, Corolla, Highlander, Land Cruiser, Prius, RAV4, Sequoia, Sienna, Solar a, Tacoma, Tundra 2007-2009 Camry HV, FJ Cruiser 2002-2005 Celica, Echo, MR2 Spyder 2006-2009 Highlander HV 2003-2009 Matrix 2009 Venza 2004-2009 Yaris When radial tires are rotating, they have the characteristic of generating force in the lateral direction between the tire and the road surface. This lateral force is comprised of two factors: •Ply-steer, which changes direction according to the rotation direction of the tires. •Conicity, which is generated inafixed direction regardless of the tire rotation direction. If these lateral forces are too strong, vehicle pulling will occur. A. Ply-Steer Lateral force due to ply-steer is produced by the construction of the belts inside the tire tread. With radial tires, the wire of the belt is slanted as shown in the illustration below. Thus, it is in the lateral direction that tire tread easily changes shape (stretches), and lateral force is generated between the tire and the road surface in the lateral direction

Toyota Automatic Transmission Serial Number Locations

0

Filed Under (Toyota Manuals) by admin on 07-10-2011

download
2006-2009 4Runner, Avalon, Camry, Corolla, FJ Cruiser, Highlander, Land Cruiser, Matrix, RAV4, Sequoia, Sienna, Solar a, Tacoma, Tundra, Venza, Yar is TSB SUPERSESSION NOTICE The information contained in this TSB supersedes TSB No. TC012-06. •Applicability has been updated to include 2008-2009 model year vehicles. TSB No. TC012-06 is Obsolete and any printed versions should be discarded. Be sure tore view the entire content of this service bulletin before proceeding. Introduction The purpose of this TSB is to assist in the identification and location of serial numbers on 2006 -2009 modelyear automatic transmissions

TOYOTA Engine Serial Number Location

0

Filed Under (Toyota Manuals) by admin on 06-10-2011

download
YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2000-2009 4Runner, Avalon, Camry, Corolla, Land Cruiser, RAV4, Sienna, Solar a, Tacoma, Tundra 2007-2009 Camry HV, FJ Cruiser, Yar is 2000-2005 Celica, Echo, MR2 Spyder 2006-2009 Highlander HV 2001-2009 Highlander, Prius, Sequoia 2003-2009 Matrix 2009 Venza The purpose of this TSB is to assist in the identification and location of engine serial numbers on 2000-2009modelyear Toyota vehicles. NOTE When writing a Field Technical and/or Product Report the serial number of the engine MUST be provided.

Incoming search terms:

TOYOTA Upper/ Lower Windshield/ Rear Glass Tick Noise

0

Filed Under (Toyota Manuals) by admin on 12-10-2011

download
Upper/Lower Windshield/Rear Glass Tick Noise Service Category Vehicle Exterior Section Window/Glass Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2003-2009 4Runner, Avalon, Camry, Camry HV, Celica, Corolla, Echo, FJ Cruiser, Highlander, Highlander HV, Land Cruiser, MR2 Spyder, Matrix, Prius, RAV4, RAV4 EV, Sequoia, Sienna, Solar a, Tacoma, Tundra, Venza, Yar is TSB REVISION NOTICE •July 13,2009 Rev2: •The Warranty Information table has been updated. •February2,2009 Rev1: •Applicability has been updated to include 2009 model years. •Titlehasbeen updated. •Introduction has been updated. •Warranty has been updated. Any previous printedversions of this service bulletin should be discarded. TSB SUPERSESSION NOTICE The information contained in this TSB supersedes TSB No. NV009-06. •Applicability has been updated to include 2008 model year applicable vehicles. TSB No. NV009-06 is Obsolete and any printed versions should be discarded. Be sure tore view the entire content of this service bulletin before proceeding

Incoming search terms: