solo 210 two stroke engine carburetor

You search Auto repair manual PDF solo 210 two stroke engine carburetor, if there are search results will appear below. If search results do not exist, please search by others keyword.



  solo 210 two stroke engine carburetor Direct Download speed 5282 Kb/s

  solo 210 two stroke engine carburetor Full Version speed 6162 Kb/s



KTM 60 SX / 65 SX REPAIR MANUAL ENGINE

0

Filed Under (KTM) by admin on 12-11-2010

download
Carburetor adjustment Basic information about the original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambient temperature of approx. 20°C (68°F), mainly for off-road use and central European premium-grade fuel (ROZ 95). Mixing ratio 2-stroke motor oil : super fuel 1:40 . Basic information of changing the carburetor setting Always start out from the original carburetor setting. Essential requirements are a clean air filter system, air-tight exhaust system and an intact carburetor. Experience has shown that adjusting the main jet, the idling jet and the jet needle is sufficient and that changes of other parts of the carburetor will not greatly affect engine performance. RULE OF THUMB: high altitude or high temperatures  choose leaner carburetor adjustment low altitude or low temperatures  choose richer carburetor adjustment * WARNING * -ONLYUSE PREMIUM – GRADE GASOLINE ROZ 95 MIXED WITH HIGH – GRADE TWO – STROKE ENGINE OIL . OTHER TYPES OF GASOLINE CAN CAUSE ENGINE FAILURE , AND USE OF SAME WILL VOID YOUR WARRANTY . -ONLYUSE HIGH – GRADE 2- STROKE ENGINE OIL OF KNOWN BRANDS ( I . E .SHELL ADVANCE RACING X). -NOTENOUGH OIL OR LOW – GRADE OILCAN CAUSE EROSION OF THE PISTON . USING TOO MUCH OIL , THE ENGINE CAN START SMOKING AND FOUL THE SPARKPLUG . -INTHE CASE OFA LEANER ADJUSTMENT OF THE CARBURETOR PROCEED CAUTIOUSLY . ALWAYSREDUCETHEJETSIZEINSTEPSOFONENUMBERTOAVOID OVERHEATING AND PISTON SEIZURE . NOTE: If despite a changed adjustment the engine does not run properly, look for mechanical faults and check the ignition system. Basic information on carburetor wear As a result of engine vibrations, throttle valve, jet needle, and needle jet are subjected to increased wear. This wear may cause carburetor malfunction (e.g., overly rich mixture). Therefore, these parts should be replaced after 1000 hours of using. Idling range – A Operation with closed throttle valve. This range is influenced by the idle adjusting screw 1 . Only make adjustments when the engine is hot. The idling speed can be changed by turning the idle adjusting screw. Turning it clockwise produces a higher idling speed and turning the screw counterclockwise produces a lower idling speed. Opening up – B Engine behavior when the throttle opens. The idle jet and the shape of the throttle valve influences this range. If, despite good idling-speed and part-throttle setting, the engine sputters and smokes when the throttle is fully opened and develops its full power not smoothly but suddenly at high engine speeds, the mixture to the carburetor will be too rich, the fuel level too high or the float needle is leaking. Part-throttle range – C Operation with partly open throttle valve. This range is only influenced by the jet needle (shape and position). The optimum part-throttle setting is controlled by the idling setting in the lower range and by the main jet in the upper range. If the engine runs on a four-stroke cycle or with reduced power when it is accelerated with the throttle partly open, the jet needle must be lowered by one notch. If then the engine pings, especially when accelerating under full power at maximum engine revs, the jet needle should be raised. If these faults should occur at the lower end of the part throttle range at a four-stroke running, make the idling range leaner; if the engine pings, adjust the idling range richer

KTM 250/ 300/ 380 SX,MXC,EXC ENGINE REPAIR MANUAL

0

Filed Under (KTM) by admin on 12-11-2010

download
Repair manual KTM 250 / 300 / 380 Art No 3206004 -E 2-2C main jet jet needle jet needle air control screw idle adjusting screw idle jet throttle valve Idling range A Operation with closed throttle valve. This range is influenced by the position of the air control screw 1 and the idle adjusting screw 2 . Only make adjustments when the engine is hot. To this end, slightly increase the idling speed of the engine by means of the idle adjusting screw. Turning it clockwise produces a higher idling speed and turning the screw counterclockwise produces a lower idling speed. Create a round and stable engine speed using the air control screw (basic position of the air control screw = open by 1.5 turns). Then adjust to the normal idling speed by means of the idle adjusting screw. Opening up B Engine behavior when the throttle opens. The idle jet and the shape of the throttle valve influences this range. If, despite good idling-speed and part-throttle setting, the engine sputters and smokes when the throttle is fully opened and develops its full power not smoothly but suddenly at high engine speeds, the mixture to the carburetor will be too rich, the fuel level too high or the float needle is leaking. Part-throttle range C Operation with partly open throttle valve. This range is only influenced by the jet needle (shape and position). The optimum part-throttle setting is controlled by the idling setting in the lower range and by the main jet in the upper range. If the engine runs on a four-stroke cycle or with reduced power when it is accelerated with the throttle partly open, the jet needle must be lowered by one notch. If then the engine pings, especially when accelerating under full power at maximum engine revs, the jet needle should be raised. If these faults should occur at the lower end of the part throttle range at a four-stroke running, make the idling range leaner; if the engine pings, adjust the idling range richer. Full throttle range D Operation with the throttle fully open (flat out). This range is influenced by the main jet and the jet needle. If the porcelain of the new spark plug is found to have a very bright or white coating or if the engine rings, after a short distance of riding flat out, a larger main jet is required. If the porcelain is dark brown or black with soot the main jet must be replaced by a smaller one. mixture too rich: too much fuel in proportion to air mixture too lean: not enough fuel in proportion to air 1 2 OPERATING RANGES OF THE CARBURETOR 2-3C Carburetor adjustment Basic information on the original carburetor setting The original carburetor setting was adapted for an altitude of approx. 500 meters (1600 ft.) above sea level, and the ambient temperature of approx. 20°C (68°F), mainly for off-road use and central European premium-grade fuel (ROZ 95 MOZ). Mixing ratio 2-stroke motor oil : super fuel 1:40 – 1:60. Basic information on a change of the carburetor setting Always start out from the original carburetor setting. Essential requirements are a clean air filter system, air-tight exhaust system and an intact carburetor. Experience has shown that adjusting the main jet, the idling jet and the jet needle is sufficient and that changes of other parts of the carburetor will not greatly affect engine performance. RULE OF THUMB:

2004 Honda CRF450R OWNER’S MANUAL

0

Filed Under (Honda) by admin on 21-11-2010

download
motorcycle can be kickstarted with the transmission in gear by disengaging the clutch before operating the kickstarter. Check the engine oil, transmission oil and coolant levels before starting the engine (page 21, 23, 24). Cold Engine Starting: 1. Turn the fuel valve ON. 2. Shift the transmission into neutral. 3. If the temperature is 35°C (95°F) or below, pull the choke knob fully out. 4. If the temperature is below 0°C (32°F), open the throttle two or three times. (The engine requires a richer mixture for starting in cold weather. When the throttle is so opened, the accelerator pump will feed extra fuel to the cylinder, thereby facilitating starting in cold weather.) 5. With the throttle closed, operate the kickstarter starting from the top of the kickstarter stroke, kick through to the bottom with a rapid, continuous motion. (Do not open the throttle, As the carburetor is equipped with an accelerator pump, excessive fuel will be charged into the engine, and the spark plug will be fouled if the throttle is opened and closed repeatedly. Excessive fuel in the engine makes kick- starting difficult.) 6. About a minute after the engine starts, push the choke knob back all the way to fully OFF. If idling is unstable, open the throttle slightly. (1) FUEL FILL CAP (2) BREATHER TUBE WARNING (1) FUEL VALVE (2) CHOKE KNOB Warm Engine Starting: 1. Turn the fuel valve ON. 2. Shift the transmission into neutral. 3. Pull the hot start lever and kick-start the engine. (Do not open the throttle.) 4. As soon as the engine starts, release the hot start lever 1. Shift the transmission into neutral. 2. Pull the hot start lever and kick-start the engine. (Do not open the throttle.) 3. As soon as the engine starts, release the hot start lever. Starting the engine excessively charged with fuel by throttle blipping or other reasons: 1. Shift the transmission into neutral. 2. With the throttle fully opened, repeat kickstarter operation approximately 10 times very slowly to discharge excessive fuel from the engine. 3. Pull the hot start lever and kick-start the engine (Do not open the throttle.) 4. As soon as the engine starts, release the hot start lever. Stopping The Engine 1. Shift the transmission into neutral. 2. Turn the fuel valve OFF. 3. Lightly open the throttle 2 – 3 times, and then close it. 4. Depress and hold the engine stop button until the engine stops completely. NOTE: • Failure to close the fuel valve may cause the carburetor to overflow. (1) THROTTLE GRIP (2) ENGINE STOP BUTTON Break-In Procedure Help assure your CRF’s future reliability and performance by paying extra attention to how you ride during the first operating day or 15 miles (25 km). During this period, avoid full-throttle starts and rapid acceleration. This same procedure should be followed each time when: • Piston is replaced • Rings are replaced • Cylinder is replaced • Crankshaft or crank bearing are replaced

HONDA CRF250X OWNER’S MANUAL

0

Filed Under (Honda) by admin on 01-12-2010

download
Always follow the proper starting procedure described below. Your motorcycle can be kickstarted wirh the transmission in gear by pulling in the clutch lever before operating the kickstarter. Preparation Make sure that the transmission is in neutral. Turn the fuel valve ON. Fuel Valve Starting Procedure Always follow the proper starting procedure described as follow. 4. Warm up the engine; don’t operate the throttle. 5. About 15 seconds after the engine startes, push the choke knob back all the way to fully OFF. If idling is unstable, open the throttle slightly. Extended use of the choke may impair piston and cylinder wall lubrication and damage the engine. High Air Temperature 35°C (95°F) or above 1. Do not use the choke. 2. Keep the throttle fully closed. 3. Start the engine following step 3 under Normal Air Temperature. Low Air Temperature 10°C (50°) or below 1. Follow steps 1-4 under Normal Air Temperature. 2. Continue warming up the engine until it runs smoothly and responds to the throttle when the choke knob is pushed back all the way to fully OFF. Extended use of the choke may impair piston and cylinder wall lubrication and damage the engine. Hot Engine Starting 1. Pull the hot start lever (3) and start the engine following step 3 under Normal Air Temperature. 2. As soon as the engine starts, release the hot start lever. NOTICE NOTICE Basic Operating Instructions 15 (1) fuel valve The three-way fuel valve is used to control the flow of fuel from the fuel tank to the carburetor. ON -Turning the fuel valve ON before attempting to start the engine allows fuel to flow from the fuel tank to the carburetor. OFF -Turning the fuel valve OFF after stopping the engine prevents the flow of fuel from the fuel tank to the carburetor. RES -Turning the fuel valve to RES allows fuel to flow from the reserve fuel supply to the carburetor. (1) fuel valve (2) choke knob Check the engine oil, transmission oil and coolant levels before starting the engine (pages 44,47,48). To restart a warm engine, follow the procedure for ”High Air Temperature. ” Normal Air Temperature 10°C-35°C (50°F-95°F) 1. Pull the choke knob (2) up all the way to fully ON, if the engine is cold. 2. Keep the throttle fully closed. 3. Pull the clutch lever all the way in, and press the starter button with the throttle completely closed. Or operate the kickstarter to start the engine. Starting from the top of the stroke, kick through to the bottom with a rapid, continuous motion. Do not operate the throttle. Allowing the kickstarter to snap back freely against the pedal stop can damage the engine case.

2005 Honda CRF450X OWNER’S MANUAL AND COMPETITION HANDBOOK

0

Filed Under (Honda) by admin on 04-12-2010

download
Starting & Stopping the Engine Always follow the proper starting procedure described below. Your CRF can be started with the transmission in gear by pulling in the clutch lever before operating the kickstarter or start button. Preparation Make sure that the transmission is in neutral. Turn the fuel valve ON. Fuel Valve Starting Procedure Always follow the proper starting procedure described as follow. 5. Warm up the engine; don’t operate the throttle. 6. About 15 seconds after the engine starts, push the choke knob back all the way to fully OFF. If idling is unstable, open the throttle slightly. Extended use of the choke may impair piston and cylinder wall lubrication and damage the engine. HighAirTemperature 35°C (95°F) or above 1. Turn the fuel valve (1) ON. 2. Do not use the choke. 3. Keep the throttle fully closed. 4. Start the engine following step 4 under “Normal Air Temperature.” LowAirTemperature 10°C (50°) or below 1. If the temperature is below 32°F (0°C), open the throttle two or three times. (The engine requires a richer mixture for starting in cold weather. When the throttle is so opened, the accelerator pump will feed extra fuel to the cylinder, thereby facilitating starting in cold weather.) 2. Follow steps 1-5 under “Normal Air Temperature.” 3. Continue warming up the engine until it runs smoothly and responds to the throttle when the choke knob is pushed back all the way to fully OFF. Extended use of the choke may impair piston and cylinder wall lubrication and damage the engine. (cont’d) NOTICE NOTICE Basic Operating Instructions 15 (1) fuel valve The three-way fuel valve is used to control the flow of fuel from the fuel tank to the carburetor. ON -Turning the fuel valve ON before attempting to start the engine allows fuel to flow from the fuel tank to the carburetor. OFF -Turning the fuel valve OFF prevents the flow of fuel from the fuel tank to the carburetor. RES -Turning the fuel valve to RES allows fuel to flow from the reserve fuel supply to the carburetor. (1) fuel valve (2) choke knob Check the engine oil, transmission oil and coolant levels before starting the engine (pages 44,47,48). To restart a warm engine, follow the procedure for”High Air Temperature.” NormalAirTemperature 10°C-35°C (50°F-95°F) 1. Turn the fuel valve (1) ON. 2. Pull the choke knob (2) fully ON, if the engine is cold. 3. Keep the throttle fully closed. 4. Pull the clutch lever all the way in, and depress the start button. Or operate the kickstarter to start the engine. Starting from the top of the stroke, kick through to the bottom with a rapid, continuous motion. Do not operate the throttle. Allowing the kickstarter to snap back freely against the pedal stop can damage the engine