spark plug size for barako for 2003 model

You search Auto repair manual PDF spark plug size for barako for 2003 model, if there are search results will appear below. If search results do not exist, please search by others keyword.



  spark plug size for barako for 2003 model Direct Download speed 5282 Kb/s

  spark plug size for barako for 2003 model Full Version speed 6162 Kb/s



SUZUKI SV1000 PERIODIC MAINTENANCE

0

Filed Under (Suzuki) by admin on 26-02-2011

download
MAINTENANCE AND TUNE-UP PRO- CEDURES This section describes the servicing procedures for each item of the Periodic Maintenance requirements. AIR CLEANER I Inspect every 6 000 km (4 000 miles, 6 months) and replace every 18 000 km (11 000 miles, 18 months) . • * Remove the seat. (LF6-7) • * Lift and support the feul tank . (C-74-65) • * Remove the air cleaner box cap O. • * Remove the air cleaner element O. • * Carefully use air hose to blow the dust from the cleaner ele- ment. CAUTION Always use air pressure on the throttle body side of the air cleaner element . If air pressure is used on the other side, dirt will be forced into the pores of the air cleaner element thus restricting air flow through the air cleaner element . PERIODIC MAINTENANCE 2-5 2-6PERIODIC MAINTENANCE • * Reinstall the cleaned or new air cleaner element in the reverse order of removal . CAUTION If driving under dusty condition, clean the air cleaner element more frequently. The surest way to accelerate engine wear is to use the engine without the element or to use a ruptured element. Make sure that the air cleaner is in good condition at all times. Life of the engine depends largely on this component! NOTE: When cleaning the air cleaner element, drain water from the air cleaner by removing the drain plug . SPARK PLUG Inspect every 6 000 km (4 000 miles, 6 months) and replace every 12 000 km (7 500 miles, 12 months) . No. 1 (FRONT) SPARK PLUG REMOVAL • * Remove the radiator mounting bolt O. • * Move the radiator forward. • * Remove the spark plug cap O. NOTE: Be careful not to damage the radiator fins . A WARNING The hot radiator and the hot engine can burn you . Wait until the radiator and the engine are cool enough to touch . • * Remove the spark plug with a spark plug wrench. 1 6 I It No. 2 (REAR) SPARK PLUG REMOVAL • * Remove the seat. (r–,-6-7) • * Lift and support the fuel tank . (=4-65) 4-65) • * Disconnect the camshaft position sensor 1O and breather hose (Z. • * Remove the rubber heat shield ® . • * Remove the spark plug cap . • * Remove the spark plug with a spark plug wrench . HEAT RANGE • * Check to see the heat range of the plug . CARBON DEPOSIT •Check to see if there are carbon deposits on the plugs . If carbon is deposited, remove it with a spark plug cleaner machine or carefully using a tool with a pointed end . SPARK PLUG GAP • * Measure the plug gap with a thickness gauge . If out of specification, adjust it to the following gap . 09900-20803 : Thickness gauge Spark plug gap OA Standard: 0.6 – 0 .7 mm (0.024 -0.028 in) ELECTRODES CONDITION •Check to see the worn or burnt condition of the electrodes . If it is extremely worn or burnt, replace the plug . And also replace the plug if it has a broken insulator, damaged thread . CAUTION Confirm the thread size and reach when replacing the plug. If the reach is too short, carbon will be deposited on the screw portion of the plug hole and engine damage may result

Incoming search terms:

SANYANG HD 125/ 200 Specifications And SERVICE MANUAL

0

Filed Under (Sym) by admin on 24-11-2010

download
heck and adjustment Fault condition Probable causes Loosen carburetor drain bolt to check if there is gasoline inside the carburetor Fuel supplied tom carburetor sufficient No fuel is supplied to carburetor Remove spark plug, install it into spark plug cap, and perform a spark test against engine ground. Perform cylinder compression pressure test. Check if sparks Weak sparks, no spark at all Low compression pressure or no pressure Re-start by following the starting procedures No ignition There are some signs of ignition, nut engine can not be started Remove the spark plug again and check it. Remove carburetor after 30 minutes and connect a hose onto fuel rich circuit. Then blow the hose with air Dry spark plug Wet spark plug Blowing in normal Blowing clogged 1. No fuel in fuel tank 2. Check if the pipes, fuel tank to carburetor and intake vacuum, are clogged. 3. Float valve clogged 4. Lines in fuel tank evaporation system clogged 5. Malfunction of fuel pump 6. Loosen or damaged fuel pump vacuum hose 7. Fuel filter clogged 1. Malfunction of spark plug 2. Spark plug foul 3. Malfunction of CDI set 4. Malfunction of AC generator 5. Ignition coil is in open or short circuit 6. Ignition coil leads open or short circuit 7. Malfunction of main switch 1. Piston ring seized 2. Malfunction of cylinder valves 3. Worn cylinder and piston ring 4. Cylinder gasket leak 5. Sand hole in compression parts 1. Malfunction of throttle valve operation 2. Air sucked into intake manifold 3. Incorrect ignition timing 1. Fuel level in carburetor too high 2. Malfunction of throttle valve operation 3. Throttle valve opening too wid

2003 DCx65 Owners And Service Manual

0

Filed Under (Cobra) by admin on 10-11-2010

download
Dimensions Wheelbase 44.75″ (1136 mm) Wheel size 14″ (356 mm) front, 12″ (305 mm) rear Seat height Engine Type 2-stroke, single cylinder, reed valve Cooling system Liquid-cooled Displacement 64.8 cc (3.95 Cubic inches) Bore and stroke 43 mm x 44.6 mm Ignition system Electronic Spark plug Splitfire SF406B Gap 0.023″ – 0.025″ (0.58 – 0.64 mm) Fuel type Sunoco MO2 X or 93 octane pump gasoline OTHER RACE FUELS ARE NOT RECOMMENDED Oil type Cobra Venom 2-cycle Race Oil Fuel / oil mix ratios 32:1 to 40:1 Ignition timing 0.050″ Carburetion 28 mm PWK style Main jet 128 Slow (Pilot) jet 38 Jet needle JJH 3rd position from the top Float height 19 mm + 0.5mm (0.75″ + 0.020″) Transmission Speed Six speed Clutch Manual hydraulic Final drive ratio 13/46 T Transmission / clutch oil type 85W 90 Gear Lubricant Quantity 530 ml (18 oz) 6 Chassis Front tire 60/100 x 14 Pressure 10 – 15 psi. Rear tire 80/100 x 12 Pressure 10 – 15 psi. Front fork Cobra USD 35 mm Fork oil type SAE 5 weight Fork oil amount 4 oz (118 ml) Fork oil level Specifications – Torque Values Torque Value ENGINE Fastener ft-lb in-lb Nm Size & Remarks Cylinder head nuts 9.2 110 12 ¼” x 20 Engine oil drain 3 36 4 8 x 1.25 Engine oil fill 2 24 2.7 14 x 1.0 Spark Plug (SP) (SP) (SP) 14 x 1.25 Crank case half 5 60 6.8 6 x 1.0 Crank case cover 5 60 6.8 6 x 1.0 Flywheel rotor nut 40 480 54 10 x 1.25 (G) Clutch hub 40 480 54 10 x 1.25 (G) Units of mm unless otherwise specified (G) denotes the use of wicking / bearing retainer (green) thread locking agent to applied to the mating surfaces of the two components but not the threads. (SP) To apply the proper torque to the spark plug when inserting, one must first screw the spark plug in until the metal gasket ring causes resistance and then turn another 1/8 to ¼ turn.

HARLEY DAVIDSON CLUTCH CABLE ASSEMBLY INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
36753-87A This kit fits 1987 and later FXLR model motorcycles. 36755-87A This kit fits 1987 and later FXRS/SP model motorcycles. 38601-89 This kit fits 1988 and later FLTC, FLTC-Ultra, FLHS, FLHTC FLHTC-Ultra and FLHTP model motorcycles. 38606-87A This kit fits 1987 and later FXR, FXRS and FXRT model motorcycles. 38607-87A This kit fits 1987 and later FLST, FXST, FXSTC, FXRP, FLTC, FLHT, FLHTP and FLHTC model motorcycles. 38617-95 This kit fits 1995 and later FXSTSB model motorcycles. 38647-98 This kit fits 1998 and 1999 FXSTB model motorcycles. 38661-00 This kit fits2000 and later FXDL, FXDS-CONV and FXDWG model motorcycles. 38664-00 This kit fits2000 and later FXSTD model motorcycles. 38665-00 This kit fits2000 and later FXSTB model motorcycles. 38666-00 This kit fits2000 and later FXSTS, FLSTS, FLSTC, FLSTF, FXDX, FXD and FXST model motorcycles. 38667-00 This kit fits 2000 and later FLTR, FLTRI, FLHT, FLHTC, FLHTCI, FLHTCUI, FLHR, FLHRI, FLHRCI and FLHP model motorcycles. 38672-01 This kit fits 2001 and later FXDWG2 model motorcycles. Kit Contents: QTY DESCRIPTION 1 O-ring, rubber 1 Cable, clutch 1 Pin, cable pivot 1 Grommet (Kit no. 38607-87A, 38660-00A and 38667-00 only) Installation NOTE A Service Manual for your motorcycle is available from your Harley-Davidson dealer. A SERVICE MANUAL IS NEEDED TO INSTALL THIS KIT. The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have your Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. 1. Refer to the Service Manual for your motorcycle model. Screw the cable adjuster all the way in to allow for maximum cable free play. 2. Remove clutch hand lever from hand-lever bracket at pivot pin. Remove original clutch cable from hand lever and transmission. Retain anchor pin bushings. 3. See Figure 1. Install lever end of new clutch cable. Position cable eyelet in clutch lever slot. Retain with new cable pivot pin through original bushings. NOTE See Figure 2. When routing cable on models where clutch cable passes through inner fairing (FLHTC, FLHTC-U and FLHTP with fairing), clutch cable eyelet may be too large to pass through clutch cable access hole in fairing. If this is the case, use the template supplied with this sheet to file out a hole to accommodate the new eyelet. Place the grommet included with kit no. 38607-87A, 38660-00A, and 38667-00 in the hole after filing. 4. Secure the clutch lever in the lever bracket with the lever pivot pin and retaining ring. 5. Follow steps outlined in the applicable Service Manual and install the transmission-end of the new cable with O- ring. 6. Adjust clutch cable according to procedure in Service Manual.

Incoming search terms:

2003 – 2008 4Runner AND 2007 – 2008 FJ Cruiser FRONT AND REAR DIFFERENTIAL GEAR OIL SPECIFICATION CHANGE

0

Filed Under (Toyota Manuals) by admin on 14-11-2011

download
75W-85 GL5 synthetic gear oil beginning with the 2008 model year. This new synthetic gear oil is compatible with 2003 – 2007 model year 4Runner and 2007 model year FJ Cruiser differentials. Please refer to the Parts Information section below for information about this gear oil and use this gear oil (or equivalent) when filling front or rear differentials with oil. 2003 – 2008 model year 4Runner vehicles. 2007 – 2008 model year FJ Cruiser vehicles. PREVIOUS PART NUMBER CURRENT PART NUMBER PART NAME TYPE QTY N/A 08885-02606 Toyota Genuine Differential Gear Oil LX 75W-85 API GL-5 SAE 75W-85 LSD As Needed N/A 08885-02506 Toyota Genuine Differential Gear Oil LT 75W-85 API GL-5 SAE 75W-85 w/o LSD As Needed Refer to the diagram below to identify if LSD or non-LSD gear oil is used on the vehicle. For applicable vehicles, there is a caution label above the filler plug, as shown below

Incoming search terms:

Honda VT1100 Shadow Guide Plug Patch Repair Manual

0

Filed Under (Honda) by admin on 24-04-2011

download
Find the guide plug.bn The guide plug is shown in the shop manual with the engine removed from the frame and the left crankcase cover removed. (You’ll find this illustration in the “ELECTRIC STARTER/STARTER CLUTCH” chapter in the “STARTER DRIVEN GEAR/STARTER CLUTCH REMOVAL” section.) It’s a little bit harder to find it on the bike. Start by following the yardstick to see where the guide plug is on my bike. To find it on your bike, lie on the ground (or, preferably a mechanics creeper) next to the bike (without the yardstick) and peek under the shift lever and over the frame There it is, just barely visible from the side of the bike. Here’s what a new one looks like: 2. Clean the guide plug and crankcase. From the front of the bike, clean the guide plug and crankcase with brake cleaner in a VERY focused spray. Let the cleaner evaporate before moving to the next step. Page 4 Rev: Draft 5/20/2007 Page 4 of 5 3. Reposition the guide plug. a. From the side of the bike, use the yardstick (or a long screwdriver if you prefer) to gently push the guide plug back into the crankcase. (Note the JB Weld from the previous patch operation.) b. From the front of the bike, gently push upward on the bottom of the upper tab (as shown below) or the bottom of the forward tab to rotate the guide plug into the proper position while maintaining pressure with the yardstick

2003 CM50 Owners And Service Manual

0

Filed Under (Cobra) by admin on 01-12-2010

download
Fastener ft-lb in-lb Nm Size & Remarks Cylinder head nuts 9.2 110 12 ¼” Crankcase bolts 6.6 80 9 6 x 1.0 Spark plug (SP) (SP) (SP) 14 x 1.25 Stator bolts 2.1 25 2.8 #8 Stator cover bolts 1.7 20 2.3 #8 Clutch cover bolts 5.8 70 7.9 6 mm Clutch 40 480 54 10*** Engine mount bolts 22 265 30 8 mm Swingarm Pivot 21 250 28 14 mm Intake manifold bolts 4.6 55 6.2 6 mm Ignition rotor nut 40 480 54 10 mm** Rear Sprocket Bolts 18 216 24 7 mm Rear shock mounts 40 480 54 10 x 1.5 Rear Axle Bolt 25 300 34 12 mm ** Use green (wicking / bearing retainer) thread locker, with primer, on the flywheel / crankshaft taper but none on the threads. *** Use green (wicking / bearing retainer) thread locker, with primer, on the crankshaft / clutch taper but use red (high strength) thread locker, with primer, on the nut. (SP) To apply the proper torque to the spark plug when inserting, one must first screw the spark plug in until the metal gasket ring causes resistance and then turn another 1/8 to ¼ turn. 7 Optional Components • Carburetor jets • Sprockets o Front o Rear • Seat with lower seat height, 22″ (559 mm), # TCHO0001 • Suspension Springs Weight of Rider (lb) Fork Spring Shock Spring Less than 38 (light) KCMZ0012A SCMU0321 (yellow, 320 lb/in) 38 – 45 (std) KCMZ0012 SCMU1360 (red, 260 lb/in) 46 to 55 (stiff) KCMZ0012B SCMU1380 (white, 380 lb/in) Extra stiff SCMU1400 (silver, 400 lb/in) • Suspension Valving Damping Rate Fork Valving Compression (right) Fork Valving Rebound (left) Shock Valving (kit) Soft (fast) KCMZ0033A KCMZ0032A SCMU0318A Standard KCMZ0033 KCMZ0032 SCMU031

HARLEY DAVIDSON GLOSS BLACK HEAD BOLT COVERS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
This kit fits 1992 and later Evolution 1340 and XL models and 1999 and later Twin Cam-equipped models. INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. Remove spark plugs. 2. See Figure 1. Install head bolt covers (1), on head bolts (3), secure using setscrew (2) and Allen wrench included with kit. To prevent setscrews from falling into the spark plug holes, start threading the setscrews into the covers before placing them over the head bolts. Position cover on head bolt so that when spark plug is reinstalled setscrew is hidden from view but accessible with Allen wrench. Do not tighten setscrews on high points of bolts. 3. Reinstall spark plugs. Tighten spark plugs to 11-18 ftlbs (15-24 Nm) . If a torque wrench is not available, finger- tighten spark plug and then, using a spark plug wrench, tighten plug an additional 1/4 turn. 4. Readjust setscrew tightness after motor has operated at full operating temperature and then cooled. 2 1 3 is 001586 1. Head bolt cover 2. Setscrew 3. Head bolt Figure 1. Head Bolt Cover Installation

Incoming search terms:

HONDA CB650/ 750F/ 900F/ 1100F/ GL1100 Spark Unit Set Installation Manual

0

Filed Under (Honda) by admin on 05-04-2011

download
INSTALLATION INSTRUCTIONS: 1. All connections must be of the highest quality, use crimped or soldered connections; twisted wires will not give a satisfactory operation. 2. Remove the seat and/or petrol tank to gain access to the original spark units (if fitted); these are normally fitted under the seat between the top frame tubing. Each of these units consists of a small alloy metal box with sleeved wires terminated by a small connector (coupler). They also have a mounting tab with a single fixing hole. 3. On four cylinder machines there will be two units, normally mounted back to back; one for cylinders 1&4 and one for cylinders 2&3. 4. For safety, disconnect the battery. 5. Unplug the couplers from each of the units. Undo the fixings and remove the units. 6. Fit the new spark units in the place of the old ones or find a suitable alternative, close to the connectors. Secure the units to the frame or mounting platform using the supplied tie-straps and adhesive mounting base (if required). If required, a thin sheet of rubber or double-sided tape can be used to keep the units in position. Do not completely wrap the units in foam rubber. 7. Push the wiring harness plugs into the new spark unit socket connectors; they will only fit one way. Reconnect the battery. 8. If you are rewiring the machine or do not have the standard wiring harness, the spark unit wire colours & functions are as follows: GREEN Ö GROUND (0 VOLTS) BLACK/WHITE Ö IGNITION SUPPLY (+12 VOLTS) VIA ENGINE STOP SWITCH YELLOW Ö IGNITION COIL OUTPUT (TO COIL —) WHITE Ö PULSE GENERATOR (WHITE RING) BLUE Ö PULSE GENERATOR (UNMARKED) There are two pulse generators, one for cylinders 1&4 and one for cylinders 2&3. The left hand one is normally for cylinders 1&4 (see fig.1). There are two wires of the same colour coming from each pulse generator, one of these wires is normally marked with a white band. The pulse generator wire with the white band connects to the white wire from the corresponding spark unit, the other pulse generator wire connects to the blue wire on the corresponding spark unit. If the white band is missing, this is normally the upper wire coming from the pulse generator. 9. Refit the seat and tank (if removed earlier). 10. Fitting is now complete, although for best results you may wish to verify the ignition timing, see the following guide

Incoming search terms:

2001 – 2003 Prius 2003 4Runner, Camry, Land Cruiser and Sequoia VEHICLES EQUIPPED WITH TRANSPONDER ECU

0

Filed Under (Toyota Manuals) by admin on 07-10-2011

download
When replacing the ECM (SAE term: PCM) or the Transponder ECU a “handshake” procedure must be performed. This ECU ID communication is necessary to enable the Transponder ECU and the ECM to recognize each other before the vehicle will start. Complete ECU communication using the following steps: 1. Insert a Master key into the ignition cylinder. 2. Turn the ignition ON (engine OFF). 3. Short Tc and CG terminals of DLC3 using the Diagnostic Check Wire (SST 09843-18020 or equivalent) and leave for 30 minutes. 4. After 30 minutes, turn the ignition OFF and remove check wire from DLC3. 5. Register any additional keys as necessary. 6. Start the vehicle to confirm successful ECU communication. Key Programming: To program or delete a key, a registered Master key is necessary unless the Transponder ECU has been reset or replaced. The Transponder ECU system incorporates a black “Master” key and a gray “Sub” key. The process during registration of these two keys is identical. The key itself now determines if it functions as Master or Sub, not the registration procedure. The maximum number of allowable Master and Sub keys vary by model. Refer to the chart below.

Incoming search terms:

Incoming search terms: