speedo healer manual

You search Auto repair manual PDF speedo healer manual, if there are search results will appear below. If search results do not exist, please search by others keyword.



  speedo healer manual Direct Download speed 5282 Kb/s

  speedo healer manual Full Version speed 6162 Kb/s



Harley Davidson Speedo Healer Installation Manual

0

Filed Under (Harley Davidson) by admin on 14-03-2012

download
a) Locate the three wire Deutsche connector that is situated behind the left hand side panel as viewed from the rear of the bike. This is normally grey in colour, and the wires are coloured red, white and black. This connector connects the rear wheel sensor to the electronic speedo head. OEM Connector b) The table below shows the function of each wire Colour Function Red +ve volts White Signal to Speedo Black GND Green Signal from Rear Pickup The +ve volts red wire should be between 8 and 12 volts, typically it is only 8 volts which is on the limit of the Speedohealer range and it is necessary to source an alternative 12 volts supply e.g. from the fuse box. I used a feed from the accessory supply which is an Orange/White wire (You need a switched +12V so don’t use the battery positive terminal.) c) Tap into the wires from the rear wheel pick and solder the Speedo healer ensuring to use the provided heat shrink cable to cover the finished work. Wiring loom Note the red wire is not used from the connector. The green wire is the feed from the rear wheel sensor which is connected to the input wire (white or yellow) of the Speedohealer. The output of the Speedohealer which is the blue wire is connected to the white wire which goes to the Harley speedo. d) Get the power from the fuse box Alternative 12 volt from fuse box Alternative 12 volt from fuse box closeup e) A suitable location for the Speedohealer is on the side of the battery box. It can be fixed by using a cable tie. Fitted to battery box f) Finally this is the OEM electronic speedo (as seen from the front and rear) and the rear wheel pickup

Incoming search terms:

2005 Yamaha Royal Star Tour Deluxe speedo Healer Installation Manual

0

Filed Under (Yamaha) by admin on 09-11-2010

download
The speed sensor is on the left side (looking from the back towards the front of the motorcycle). Just FYI, here is the speed sensor coming off of the drive shaft behind the left saddlebag. The speed sensor connection for the Speedo Healer is behind this red cover. Take off the seat. There are two screws. One pointed out by the arrow and one on the opposite side. Also, remove the screw on the red cover. After removing the screw on the red cover, remove the cover by pulling it straight away from the bike. It is held on by 2 rubber grommets. The arrow points to the speed sensor coupler. Pull the connection apart. There is a little tab holding the connector together that will need to be depressed in order to get it apart.Hook the SH harness into the appropriate connectors. It only goes one way. The Yamaha plug and go kit works perfectly with no splicing required. Here is a close-up of the connection. Run the cable up under the bar towards the battery and hook the wires up to the Speedo Healer unit. The speedo healer fits nicely right behind the battery. You can barely see it next to the intercom. Note, none of the wires in this example have been secured yet. Put the red cover back on. Figure out the error that needs to be adjusted and make the adjustments to the Speed Healer per their instructions. Put the seat back on and you’re good to go. Be sure to verify that your adjustment was correct before believing your speedometer to be accurate. With the right adjustment, it will be, but don’t wait for a cop to tell you that you miscalculated! The electronic cruise control was not affected by the installation of this unit. I ended up setting mine to -7.5% after chasing my wife’s ’03 Vue for a couple of times. I ended up reading 59mph to her 60mph (previously it read 65mph to her 60mph) which is right where I wanted it since her speedometer reads a little fast, too. My back tire is about halfway worn. Your adjustment may vary

Incoming search terms:

Yamaha Royalstar Royal Star Tour Deluxe Speedo Healer Installation

0

Filed Under (Yamaha) by admin on 07-01-2012

download
he speed sensor is on the left side (looking from the back towards the front of the motorcycle). Just FYI, here is the speed sensor coming off of the drive shaft behind the left saddlebag. – 7/2 -The speed sensor connection for the Speedo Healer is behind this red cover. Take off the seat. There are two screws. One pointed out by the arrow and one on the opposite side. Also, remove the screw on the red cover. After removing the screw on the red cover, remove the cover by pulling it straight away from the bike. It is held on by 2 rubber grommets. – 7/3 -The arrow points to the speed sensor coupler. Pull the connection apart. There is a little tab holding the connector together that will need to be depressed in order to get it apart. – 7/4 -Hook the SH harness into the appropriate connectors. It only goes one way. The Yamaha plug and go kit works perfectly with no splicing required. Here is a close-up of the connection. – 7/5 -Run the cable up under the bar towards the battery and hook the wires up to the Speedo Healer unit. – 76 -The speedo healer fits nicely right behind the battery. You can barely see it next to the intercom. Note, none of the wires in this example have been secured yet. Put the red cover back on. Figure out the error that needs to be adjusted and make the adjustments to the Speed Healer per their instructions. Put the seat back on and you’re good to go. Be sure to verify that your adjustment was correct before believing your speedometer to be accurate. With the right adjustment, it will be, but don’t wait for a cop to tell you that you miscalculated! The electronic cruise control was not affected by the installation of this unit. I ended up setting mine to -7.5% after chasing my wife’s ’03 Vue for a couple of times. I ended up reading 59mph to her 60mph (previously it read 65mph to her 60mph) which is right where I wanted it since her speedometer reads a little fast, too. My back tire is about halfway worn. Your adjustment may vary

Incoming search terms:

HARLEY DAVIDSON SCREAMIN' EAGLE TWIN CAM 110 (1800 CC) CONVERSION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-02-2011

download
REMOVAL Prepare for Service 1. Position motorcycle on a suitable lift. NOTE If vehicle is equipped with Harley-Davidson Smart Security System, see owner’s manual for instructions to disarm the system. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect battery cables, negative (-) battery cable first. 3. Remove seat according to the instructions in the service manual. 4. Refer to service manual to remove left saddlebag and side cover. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 5. Remove fuel tank according to the instructions in the service manual. Remove Engine Components 1. Remove existing air cleaner assembly. Discard backplate but save remaining parts. Refer to AIR CLEANER REMOVAL in service manual. 2. Remove existing exhaust system. Refer to EXHAUST SYSTEM REMOVAL in service manual. 3. Remove engine from chassis following the instructions in the service manual. 4. Disassemble engine top end and bottom end. Refer to appropriate ENGINE sections in service manual. 5. Remove existing clutch diaphragm spring. Refer to CLUTCH REMOVAL in service manual. The procedures in this instruction sheet should be performed by one experienced in precision measuring techniques. Failure to meet tolerances called for in this instruction sheet can result in engine damage. (00511b) -J04793 1 2 is03517 1. O-ring counterbore 2. Spigot bore Figure 1. Spigot Bore and O-Ring Counterbore Dimensions Table 1. Spigot Bore and O-Ring Counterbore Dimensions Depth Bore Description 1.625 +/- 0.010 in. (41.3 +/- 0.25 mm) 4.205 +/- 0.010 in. (107 +/- 0.25 mm) Spigot Bore 0.085 +/- 0.003 in. (2.16 +/- 0.08 mm) 4.415 +/- 0.002 in. (112 +/- 0.05 mm) O-Ring Counter- bore is03456 Figure 2. Cylinder Wall MACHINE CRANKCASE Crankcase Boring Preparation NOTE During final assembly of the engine, Harley-Davidson recommends replacing the OE cylinder studs with Screamin’ Eagle High Tensile Studs (16505-01). 1. Remove cylinder studs from the engine crankcase. 2. Mask off all bearings and oil holes to prevent debris and contaminants from entering those areas. 3. Inspect and clean engine case mating surfaces. 4. See Figure 6. Reassemble engine case with OE screws, except the top center screw between the cylinders, and tighten to specifications listed in service manual. NOTE To prevent damage to crankcase boring tool, it is important to replace the top center screw with a modified top center screw (1093). This screw is included in the Crankcase Boring Tool Kit (94419-06) and can be purchased separately from a Harley- Davidson dealer. 5. Install modified top center screw (1093) between the cylinders and tighten to 50-90 in-lbs (5.6-10.2 Nm). 6. See Figure 1 and Table 1. Machine crankcase cylinder spigot bore and O-ring counterbore to the dimensions shown. Modify Crankcase

Incoming search terms:

SUZUKI GSX-R1000 SERVICE MANUAL

0

Filed Under (Suzuki) by admin on 12-11-2010

download
Cover the throttle bodies to prevent anything from dropping into the engine. 1. Remove the front seat and disconnect the battery. (Refer to Service Manual, Page 8-8) 2. Lift up the fuel tank. (Refer to Service Manual, Page 5-3) 3. Remove the air cleaner box. (Refer to Service Manual, Page 5-14) 4. Remove and replace the ISC valve. (Refer to Service Manual, Page 5-25) NOTE: Since the ECM is also being replaced there is no need to perform the ISC valve preset operation. 5. Install the air cleaner box in reverse order of removal. (Refer to Service Manual, Page 5-14) 6. Lower the fuel tank. (Refer to Service Manual, Page 5-3) 7. Remove the upper seat rail plate. Disconnect and remove the ECM. (Figure 1) @ ISC Valve Mounting Screw Torque: 2.1± ±0.6 N.m (1.5± ±0.4 lb-ft) ! Carefully insert the ISC valve straight into the throttle body hole to prevent damaging the o-ring. Turn the ISC valve slightly to confirm that the o-ring has not twisted. Using the new screw provided in the replacement parts kit, make sure the screw is completely seated on the plate after the screw has been tightened to the specified torque. 4. Remove and replace the ISC valve. (Refer to Service Manual, Page 5-25) NOTE: Since the ECM is also being replaced there is no need to perform the ISC valve preset operation. ! Cover the throttle bodies to prevent anything from dropping into the engine. 1. Remove the front seat and disconnect the battery. (Refer to Service Manual, Page 8-8) 2. Lift up the fuel tank. (Refer to Service Manual, Page 5-3) 3. Remove the air cleaner box. (Refer to Service Manual, Page 5-14) REPLACEMENT PROCEDURE: 8. Install the new ECM in reverse order of removal. Apply thread lock to the upper plate mounting bolts when reinstalling the upper seat rail plate.

Incoming search terms:

HARLEY DAVIDSON VRSC CHROME WHEEL KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-03-2011

download
Installation To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1 WARNING 1 WARNING ® Kit Numbers 41279-04, 41282-04, 41463-05, 41467-05, 41633-05, 41634-05, 41640-05, and 41639-05 1 of 3 Figure 1. Rear Wheel Removal i02495 1. Axle (keep) 2. Axle adjuster (keep) 3. Axle nut (keep) 4. “E”-clip (keep) 5. Spacer (3) (keep) 6. Torx screw (5) (replace) 7. Brake disc (keep) 8. Wheel assembly (replace) 9. Valve cap (keep) 10. Compensator bowl (keep) 11. Compensator cushion (keep) 12.12 pt screw (5) (keep) 13. Lockwasher (5) (keep) 14. Sprocket assembly (keep) 1. Refer to the Service Manual and follow the MAXI-FUSE instructions to remove the right-side cover and maxi- fuse. Proceed to Step 2 for the wheel being replaced. Rear Wheel 2. See Figure 1. Remove the rear wheel per the REAR WHEEL, REMOVAL instructions in the Service Manual. 3. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. 4. Re-assemble all saved components to the new chrome rear wheel assembly. See REAR WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 5. Fasten the brake disc to the valve stem side of the wheel using the Torx®screws from the kit. Install the compensator bowl with the 12-point screws and lockwashers saved earlier. 6. Install the new wheel to the rear fork. Refer to REAR WHEEL, INSTALLATION in the Service Manual. Proceed to Step 7. Front Wheel 2. See Figure 2. Remove the front wheel per the FRONT WHEEL, REMOVAL instructions in the Service Manual. 3. Disassemble, clean and inspect all parts to be re-used per Service Manual instructions. Mark the left and right brake discs so they can be re-installed to the same location. 4. Re-assemble all saved components to the new chrome front wheel assembly. See FRONT WHEEL, ASSEMBLY in the Service Manual. Do not re-use brake disc screws. Re-using disc screws can result in torque loss and damage to rotor and/or brake assembly. (00319b) 5. Using the Torx ® shoulder bolts from the kit, and the saved spring washers fasten the brake discs to the same side of the wheel from which they were removed. 6. Install the new wheel to the front forks per the FRONT WHEEL, INSTALLATION instructions in the Service Manual. Proceed to Step 7. Front and Rear Wheels 7. Refer to the Service Manual and follow the MAXI-FUSE instructions to replace the maxi-fuse and right-side cover. After servicing brakes and before moving motorcycle, pump brakes to build brake system pressure. Insufficient pressure can adversely affect brake performance, which could result in death or serious injury. (00279a) After servicing the brake system, test brakes at low speed. If brakes are not operating properly, testing at high speeds can cause loss of control, which could result in death or serious injury. (00289a) Maintenance and Cleaning Chrome parts must be maintained regularly to ensure that they keep their original shine and luster. 1. Clean heavily-soiled wheel surfaces using Harley Wheel and Tire Cleaner, part number 94658-98, applied with Harley Wheel and Spoke Brush, part number 43078-99. 2. Thoroughly clean chrome with a good quality chrome cleaner, such as Harley Bright Chrome Cleaner, part number 94683-99. 3. After cleaning and polishing, seal the finish with a good quality sealer such as Harley Glaze Polish and Sealant, part number 99701-84

Incoming search terms:

Triumph Daytona 600 Installation of a Speedo Healer

0

Filed Under (Triumph) by admin on 28-10-2010

download
This is a step by step instruction on the new 4.0 version of the Speedo Healer on a Triumph Daytona 600. This is a “plug and play” connection that will take between 30 minutes to an hour depending on how well you know your Triumph Daytona. The tools you will need are a 5mm Allen wrench and a pair of pliers and a 10mm socket wrench. Let’s get started. First you will have to make sure you have everything. You should have the Speedo Healer, main wiring harness, speed recall wiring harness, and zip ties. 1/10 Next if you have a rear stand this will be the time to put your bike on its stand. If you don’t have one that is fine, but it makes life a lot easier if you do. Next you will have to remove your seat. You will need your Allen wrench and to get to the screws you have to pull back on the seat and you will see two screws, remove both of them. Then you should be able to lift and pull the seat off. Set the seat aside. 2/10
Next you will see two gold colored round spools. Use your Allen wrench to remove both of these, there is one on each side. Next you will see two tabs that are turned over the gas tank. You will need to turn these so they are not touching the gas tank. Some times you can do this by hand, but you might need to loosen it with a 10mm socket. 3/10 Next move up to the top of the gas tank next to the yoke and there will be another screw that you need to remove with your Allen wrench

HARLEY DAVIDSON SOFTAIL 6 SPEED TRANSMISSION – COMPLETE INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-04-2011

download
Removal of Original Transmission 1. Position motorcycle on a suitable lift. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the battery cables, negative cable first. 3. Refer to the TRANSMISSION CASE REMOVAL in the Service Manual and follow the instructions given to remove the components with the following steps. 4. Refer to PRIMARY CHAINCASE COVER REMOVAL in the Service Manual and follow the instructions given to remove the primary chaincase cover. Wear safety glasses or goggles when removing or installing retaining rings. Retaining rings can slip from the pliers and could be propelled with enough force to cause serious eye injury. (00312a) 5. See the PRIMARY CHAIN and COMPENSATING SPROCKET REMOVAL in the Service Manual and use the instructions given to remove the primary drive assem- bly. 6. Refer to the STARTER REMOVAL in the Service Manual and remove the the starter. 7. See the VEHICLE SPEED SENSOR section and unplug the vehicle speedometer sensor connection and remove the mounting bolt. Lift sensor from the transmission case and set aside for later re-installation. 8. Refer to NEUTRAL SWITCH and disconnect the connectors from the neutral switch. 9. Refer to PRIMARY CHAINCASE in the Service Manual and follow the instructions given to remove the primary chaincase housing. 10. Refer to EXHAUST SYSTEM in the Service Manual and remove the exhaust. 11. See the REAR WHEEL REMOVAL and loosen but, do not remove rear axle to relieve drive belt tension and remove the belt from the sprocket from the transmission. 12. Refer to OIL TANK REMOVAL in the Service Manual and follow the instructions given to drain, remove the oil tank and detach the vent, feed and return lines. 13. Refer to CLUTCH CONTROL in the Service Manual and follow the instructions given to remove the clutch cover and disconnect the clutch cable end from the cover. Set the cable aside for later re-installation

Incoming search terms:

HARLEY DAVIDSON DYNA STATOR AND ROTOR KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 30-03-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect negative battery cable. See BATTERY MAINTENANCE in Service Manual. 2. Remove primary cover, primary drive, and clutch. See DRIVE COMPONENTS in Service Manual. 3. Remove primary chaincase according to the instructions in the Service Manual. 4. See Figure 2. Pull off the alternator rotor (1) using two bolts inserted through the holes in the rotor face. 5. Remove the two T-27 TORX screws (2). 6. Unplug the voltage regulator and remove the stator (3). See VOLTAGE REGULATOR in Service Manual. 7. Disassemble connector [46B] (A). See DEUTSCH ELECTRICAL CONNECTORS in Service Manual. NOTE Contact cleaner, alcohol, or glass cleaner sprayed on rubber grommet (B) will provide lubrication when pulling it through crankcase hole. 8. Move grommet (3) to one side and spray contact cleaner into gap. Repeat for other side. Pull rubber grommet (B) through crankcase hole. 9. Pull wires through crankcase hole. INSTALLATION 1. Insert wires through crankcase hole. 2. See Figure 1. Push rubber grommet (B) through crankcase hole. If necessary, apply the same lubricant used during removal. 3. Insert wires into connector [46B] (A). 4. Mate connector [46]. See VOLTAGE REGULATOR in Service Manual. is03776 Figure 1. Voltage Regulator 5. See Figure 2. Install the stator (3) on the crankcase and fasten in place using new TORX screws (2). Tighten to 55-75 in-lbs (6.2-8.4 Nm). 6. Install the rotor (1) on the sprocket shaft. 7. Apply Loctite Threadlocker 262 (red) to sprocket nut threads. Tighten sprocket nut to 150-165 ft-lbs (203.4- 223.7 Nm). 8. Install primary chaincase according to the instructions in the Service Manual. 9. Install clutch, primary drive, and primary cover. See DRIVE COMPONENTS in Service Manual. 10. Connect negative battery cable. See BATTERY MAINTENANCE in Service Manual

Incoming search terms:

KTM 250-525 SX, MXC, EXC RACING ENGINE REPAIR MANUAL

0

Filed Under (KTM) by admin on 07-02-2012

download
TM REPAIR MANUAL IN LOOSE-LEAF FORM STORING THE REPAIR MANUAL IN THE BINDER -Put the index into the binder. -Put the front page of the repair manual (210×297 mm) into the transparent pocket provided for this purpose on the outside of the binder. -Put the spine label (170×45 mm) into the transparent pocket provided for this purpose on the spine of the binder. -Put the summary list of contents (150×297 mm) into the transparent pocket provided for this purpose on the inside of the binder or insert this page on the beginning of the manual. -Then insert the individual chapters of the manual between the sheets of the index according to the page number printed in the right bottom corner of each page. Example: page no. 3-5 3 = chapter 3 5 = page 5 All pages with a page number that begins with the digit 3, for example, must be put under the index heading „Chapter 3″. -Index sheets that have not been marked with a certain chapter are for your personal convenience. T he respective headings can be entered in the list of contents. Remove page (s) Replace by page (s) Insert page (s) after page 2-1 / 2-7 2-1C 2-7C to 2-9C 3-1 3-1C 4-1 to 4-14 4-1C to 4-13C 5-1 / 5-3 5-1C / 5-3C 5-6 to 5-8 5-6C to 5-8C 5-12 to 5-26 5-12C to 5-27C 6-1 / 6-4 6-1C / 6-4C 6-7 to 6-16 6-7C to 6-17C 7-1 to 7-2 7-1C to 7-2C 7-7 to 7-11 7-7C to 7-11C 8-1 to 8-13 8-1C to 8-21C 9-1 9-1C 9-10 to 9-13 9-10C to 9-16C 10-1 10-1C 10-8C to 10-11C 11-1 11-1C 11-11C to 11-13C
Repair manual KTM 250-525 SX, MXC, EXC RACING Art.-No. 3206007 -E EXPLANATION – UPDATING Edition 01/2003 3.205.85-ERepair Manual 400/520 SX, MXC, EXC RACING Basic version Model year 2000 (Engine number with first digit “0″) 2/2000 3.210.01-EUpdating of Rep.Manual 3.205.85-E Model year 2001 (Engine number with first digit “1″) 1/2001 3.210.44-EUpdating of Rep.Manual 3.205.85-E Model year 2002 (Engine number with first digit “2″)

Incoming search terms:

Incoming search terms: