speedometer repair for 2007 vtx 1300 honda

You search Auto repair manual PDF speedometer repair for 2007 vtx 1300 honda, if there are search results will appear below. If search results do not exist, please search by others keyword.



  speedometer repair for 2007 vtx 1300 honda Direct Download speed 5282 Kb/s

  speedometer repair for 2007 vtx 1300 honda Full Version speed 6162 Kb/s



HARLEY DAVIDSON FXD (Dyna Super Glide) TACHOMETER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
1995 Models To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative cable first) before proceeding. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1.1995 MODELS, REMOVAL OF ELECTRONIC SPEEDOMETER AND BRACKET 1a. Refer to applicable Service Manual procedure and remove seat. 1b. Refer to applicable Service Manual procedure and remove fuel tank. Stop the engine when refueling or servicing the fuel system. Do not smoke or allow open flame or sparks near gasoline. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00002a) 1c. Remove speedometer sensor cable from mounting clips under tank. See Figure 1. The 3-place speedometer sensor connector [65] is located on the frame beneath the seat. Remove connector from t-stud and disconnect. Cut cable tie holding sensor wires to right rear frame tube. 1d. Refer to applicable Service Manual procedure and remove headlamp, for work clearance. 1e Remove handlebar clamp screws securing speedometer bracket. Remove speedometer, bracket, and harness. 2.1995 MODELS, DISCONNECT MAIN WIRING HARNESS 8-PLACE CONNECTOR [21B, A] (FIGURE 2) 2a. Disconnect the battery, negative cable first. Refer to applicable Service Manual procedure and disconnect main wiring harness 8-place connector [21A, B], at the front of the motorcycle. 3.1995 MODELS, REMOVE SPEEDOMETER LEADS FROM 8-PLACE CONNECTOR [21B, A] (FIGURE 2) 3a. See Figure 2 and Service Manual wiring schematic. Pull the following wires and terminals out of connector [21B]. Wire Color Cavity Number Orange/white 5 White/green 1 Black 2 3b. Remove the large female connector from the fuel gauge black wire. 3c. Slide the wires removed in step 2a out of the plastic conduit covering the wires connected to the 8-place connector. 1 WARNING 1 WARNING 1 WARNING Figure 1. Speedometer Sensor Connection [65] 4973 Speedometer sensor connector [65] Figure 2. Tachometer/Speedometer Wire Splices and Terminal Connections [21B, A] i00240-.tif Splices 4.1995 MODELS, REMOVE INDICATOR LAMPS FROM BRACKET 4a. Remove the screws that secure the indicator lamps assembly to the speedometer bracket. Retain screws and indicator lamps assembly for installation on speedometer/tachometer bracket later. 5.1995 MODELS, REMOVE SPEEDOMETER FROM BRACKET 5a. Unscrew boot from speedometer reset switch. Remove cover screws and rear cover. 5b. See Figure 3. Note position of rear speedometer gasket and remove it. Push on rear of speedometer while simultaneously pulling speedometer and front gasket from bracket. Do not remove front gasket from the speedometer. 6.1995 MODELS, INSTALL SPEEDOMETER IN KIT BRACKET 6a. See Figure 5. Place wires from speedometer through front of left opening in double bracket. Lubricate the front and rear gaskets with isopropyl alcohol or glass cleaner to ease installation. 6b. Insert speedometer into the front of the double bracket. Be sure wire guides are aligned with opening at bottom of bracket. 6c. Place rear gasket in position and align gasket tabs. Work gasket into space between speedometer and bracket by pushing speedometer against one side of bracket while pushing gasket into position at the opposite side. 6d. Add amber bulb assembly from kit to speedometer in order for tachometer and speedometer backlighting to match. 6e. Replace cover and boot from reset switch.

Incoming search terms:

YAMAHA XVZ 1300 Royal Star/ Venture SPEEDOMETER COWL INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 07-11-2010

download
Speedometer Cowling Chrome 1 2 Alcohol Wipe 1 NOTE: Allow time for the 3M® brand quality tape to cure for 24 hours at 19-32° C before washing or waxing the motorcycle. INSTALLATION 1. Position the Speedometer Cowl in front of the Speedometer. The Cowl attaches to the Speedometer Cover, not on the rubber ring around the Speedometer. The Cowl should be symmetrically located in relation to the Speedometer, use the Speedometer markings as a reference. 2. Remove the red backing tape from the adhesive strip on the base of the Speedometer Cowl. 3. Position the Speedometer Cowl as done in step 1. Make any position adjustments now. 4. Firmly press the Speedometer Cowl in place on the Speedometer Cover. 5. Allow twenty-four hours for the adhesive to fully set before washing or waxing.

Incoming search terms:

BMW K 1300 S, K 1300 R and K 1300 GT SPECIFICATION

0

Filed Under (BMW) by admin on 17-11-2010

download
The K 1300 S with 175 hp, the K 1300 R with 173 hp and the K 1300 GT with 160 hp. The new K bikes feature updated transmission and clutch assembly, plus smoother engine performance and new switchgear. Von Kuenheim continues: “By raising capacity to 1300 cc, our engineers have not only increased output but also torque on all three models. At the same time the driveline was intensively revised from air/fuel mixture formation right through to the exhaust system. In this way we have been able to optimize partial load behavior as well as throttle response. Now the clutch can be operated with even less effort and with greater refinement. Shifting has been improved tangibly due to constructional changes to the gearbox and drive.” BMW is introducing new options for the 2009 as well. The popular Electronic Suspension Adjustment that first appeared on the 2005 K 1200 S has now been updated with even more on-the-fly adjustability and it’s called ESA II. Also new is the quick-shifter option, racing-style gear shift assistant, borrowed from BMW’s race-ready HP2 Sport. Automatic Stability Control (ASC) is also offered as an option on the new K bikes. “Both the K 1300 S and also the R will also have the shift assistant – familiar from the HP2 Sport – available as an option for the first time,” von Kuenheim emphasized. “We have also advanced the chassis. The new lower longitudinal strut is now made of aluminum and is thus considerably lighter. This makes the front wheel guidance response even more sensitive. The result of this comprehensive development work is superior handling, improved rideability and lower fuel consumption. The electronically adjustable suspension – called ESA in short – was launched as a world first on the K 1200 S. Now we are presenting the new, well-proven ESA II as an option for the K Series. Apart from the suspension and damping this unique system also allows the spring rate to be adjusted at the press of a button. The K Series model revision also heralds a new and innovative generation of switches and controls.

Incoming search terms:

Honda VTX 1300 EZ-Steer Installation Instruction

0

Filed Under (Honda) by admin on 16-02-2011

download
installation of the Champion EZ-Steer system is similar to the installation of the OEM triple clamps of your Honda VTX 1300 Motorcycle. We strongly recommend that you use your OEM service manual and follow the prescribed disassembly, installation and torque specifications (except where noted below) for the upper and lower clamp assembly. Recommended Procedures • Disconnect all wiring to headlight and remove headlight, windscreen (if so equipped) and brackets from motorcycle. • Remove handle bars from top clamp. • Remove brake caliper and brackets; disconnect all mounting points on brake lines. Secure calipers to frame being careful not to damage brake lines. • The wheel and fork tube assembly can be removed as one complete unit. • Remove caps and install supplied extensions to fork tubes using the supplied o-rings. Apply lubricant to o-rings and extensions prior to installing to fork tubes. Reinstall OEM caps and o-rings. • Remove steering lock from OEM bottom clamp and install on Champion’s bottom clamp. • Replacing the upper OEM bearing and race with the Champion supplied bearing and race, install Champion’s lower triple clamp to motorcycle reusing original hardware as removed. Torque bearing lock nut to 35 lb. ft. • Install fork tube covers to bottom clamp if supplied with OEM motorcycle. • Remove OEM nylon tube cover sliders from lower fork legs and replace with supplied sliders, if required for lower chrome covers on C models. See figure on the right. • Install Champion upper clamp with OEM washer and dome nut. Leave loose. • Slide forks up and into the upper clamp until top of extension is flush with top surface of clamp. • Torque dome nut to 75 lb. ft. • Ensure that fork tube extensions are flush with top of upper clamp. Torque upper 8mm bolts to 20 lb. ft and lower 10 mm clamp bolts to 30 lb. ft. • Install handle bars to upper clamp using OEM nut and flat washers. • Reinstall brake line holders to the lower triple clamp. • Reinstall all other OEM parts as removed. • Bleed brakes.

Honda VTX 1300 Trike Conversion Installation Manual

0

Filed Under (Honda) by admin on 27-10-2010

download
Removal of Original Parts Secure and raise the motorcycle 9 to 10 inches using a quality motorcycle lift. Remove the following from the vehicle. See OEM manual for detailed instructions. Items to be retained for reinstallation after modification are noted. · Rider’s Seat (to be re-installed without modification) · Passenger Seat (to be reinstalled without modification) NOTE: OEM front and rear seat mounting bolts and brackets to be retained and reused. · Left and right passenger foot rests. (to be re-installed later). · Mufflers (to be re-installed and relocated with minor modification) · Rear Fender (complete w/ sub frame and all attaching parts) · Swing Arm, Drive Shaft and Rear Wheel (complete w/ all attaching parts) · Rear brake Line to hard line in front of the Swing Arm. Core Return There are NO core return parts for this model. Honda VTX 1300 TRIKE CONVERSION CHAMPION TRIKES Installation Manual Page 7 of 16 Revision 2 3 Installation of Champion Trike Conversion Kit 3.1 Modify Frame and Passenger Footrests. a. Cut and remove passenger foot rest mount from OEM frame on both sides (left hand side picture shown) . Figure 1 b. Clean cut frame and paint black. c. Remove and secure Charcoal Canister. d. Cut and remove charcoal canister frame bracket. Figure 2 e. Clean cut frame and paint black

Incoming search terms:

1996+ HARLEY DAVIDSON FLH INNER AND OUTTER FAIRING MOUNT FOR HONDA VTX 1300 installation

0

Filed Under (Tips and Review) by admin on 09-04-2012

download
This mount was made to attach the HD FLH assembled fairing to the 4 fork mounting points on the VTX 1300 using the Memphis Shades mounts. This allows use of the MS allen wrench to quickly remove the fairing if needed. You will have to make or buy a headlight extension. Has to be done first. I used a 5″ x 5″ x .5″ piece of aluminum stock and made one to bump the headlight out 4″. There will be some trimming and relocating of brackets. And you’ll have to buy longer bolts to mount everything correctly. Get the headlight squared away first, then do the fairing. Take a length of 1″ aluminum angle stock and cut two 17″ pieces from it. These will be the uprights for the “H” brace. Measure 5.5″ from the bottom of one piece and center punch for a hole. Drill a large enough hole to slip over the MS mounting hardware on the forks. Start at about ½” bit and notch out as necessary. Center of this hole has to be 5.5″ from the absolute bottom of the angle iron. In the same location, drill out another notch for the bottom mounting point. A drill press is handy for these modifications and you can hog out the mounting notches with a file, dremmel, etc., until they fit. Do the same for the other length of 1″ angle stock but make sure it is a mirror image of the first one. Test fit these by mounting them to the MS fork brackets using the MS bracket hardware. Bottom notch goes in first, then the top notch. I epoxied the back “nuts” of the mounting hardware to the fork mounting brackets. It keeps it in place when you’re taking the fairing on and off the bike. On the top mounting points, I epoxied a washer with one side ground flat to the bolt’s mounting ferule. This allowed better contact between the H brace and the fork mounting bracket. Didn’t want that fairing falling off. Adjust as necessary and after the test fit, remove.

2007-2008 Honda VTX1300C/R/S/T Fuel Valve Diaphragm Replacement Manual

0

Filed Under (Honda) by admin on 21-04-2011

download
According to Federal law, any affected units in your new or used inventory cannot be sold or leased until they are repaired. Refer to the REPAIR VERIFICATION and REPAIR PROCEDURE sections of this Service Bulletin.
Before you begin the repair procedure, check if the repair has been performed on the unit. See the IDENTIFICATION section of this Ser- vice Bulletin for more details. • If there is a punch mark – No further action is necessary. • If there is no punch mark – You must pro- ceed with the REPAIR PROCEDURE sec- tion of this Service Bulletin. NOTE: Units repaired in the warehouse may not be reflected on iN at the begin- ning of the campaign. For this reason, always check the VIN stamp prior to per- forming this repair. If you have any questions about repair verifi- cation, please contact your DSeM or TechLine at (800) 421-1900, option 9. NOTE: Refer to section 2-7 of the 2003-2008 VTX1300C/R/S/T Service Manual for specific fuel tank removal instructions. 1. Remove the fuel tank using the procedure in the Service Manual. However, do not remove the fuel valve from the fuel tank. 2. Drain the fuel into an approved container. 3. Remove the four screws and diaphragm cover. NOTE: The diaphragm cover is under spring pressure. Do not lose the spring or screws. The countermeasure part has a paint mark near the air vent hole. 4. Replace the diaphragm, spring, cover, and screws with new parts included in the kit. Install the new diaphragm with the plastic retainer facing the diaphragm cover. NOTE: Make sure the air vent hole is facing downward towards the ground. 5. Reinstall the fuel tank using the procedures in the Service Manual. 6. Refill the fuel tank

Incoming search terms:

MECHANIC CERTIFICATION REQUIREMENTS MDOS Form: Repair Facility Manual

0

Filed Under (Tips and Review) by admin on 18-11-2010

download
Chapter 7: Mechanic Certification Requirements Page 4 7-2.2 Heavy-duty Truck Certification Categories. The Heavy-duty Truck Repair categories requiring mechanic certification to repair vehicles over 10,000 pounds G.V.W. are: a) Engine Repair, Gasoline; b) Engine Repair, Diesel; c) Drive Trains; d) Brakes and Braking Systems; e) Suspension and Steering Systems; f) Electrical Systems; g) Collision-Related Mechanical Repair. 7-2.3 Other On-road Vehicle Certification Categories. Repair categories for other on-road vehicles that require mechanic certification to perform repairs are: a) Motorcycle; b) Recreational Trailer. Automobile and Light Truck Certification Categories. The repair categories requiring mechanic certification to repair vehicles under 10,000 pounds gross vehicle weight (G.V.W.) are: a) Engine Repair; b) Engine Tune-up/Performance; c) Front End, Suspension and Steering Systems; d) Brakes and Braking Systems; e) Automatic Transmission; f) Manual Transmission, Front and Rear Drive Axles; g) Electrical Systems; h) Heating and Air Conditioning; i) Collision-Related Mechanical Repair; j) Unitized Body Structural Repair; k) Pre-1973 Vehicle Repair

Incoming search terms:

The Honda VTX 1300 Keyless Ignition Switch Installation instructions

0

Filed Under (Honda) by admin on 04-11-2011

download
Remove the seat from the motorcycle.2. Lift the ignition module off of the battery cover and let it drape over the side of the motorcycle. 3. Remove the battery cover and disconnect the negative battery cable. 4. Remove the gas tank and set it aside. There is a vent line at the right rear of the tank, a vacuum line and the gas feed line on the left side of the tank at the petcock, and two speedometer connectors at the left front of the gas tank. 5. Remove the clip from the top of the steering head cover and remove the right hand side cover. See picture at right. 6. Remove the headlight to expose the wiring connectors inside the headlight shell. 7. Remove the left-hand side cover. On the left side of the frame is an electrical wire shroud wire tied to the left side of the frame with a reusable wire tie. Inside this cover is the 3-pin connector that connects the ignition switch to the bike’s wiring harness. Pull the small lever back to release the wire tie and remove the wire tie. Pull back the wire shroud to reveal the wire connectors inside. Disconnect the 3-pin connector that comes from the ignition switch. Remove the two bolts holding the ignition switch to the bike’s frame. See Picture at right. Remove the ignition switch from the bike. You may have to remove the connector body from the ignition switch wires to slide the wires through the frame when removing the ignition switch. You may now reinstall the side cover. 8. Lay the new wiring harness along the backbone of the bike with the two 9-pin connectors at the headlight and the 6-pin and 3-pin connectors at the battery. Insert the two 9-pin connectors through the large hole in the back of the headlight shell. Inside the headlight shell is a red 9-pin connector. Disconnect this red 9-pin connector and insert the new wiring harness connecting each side to the red 9-pin connectors. See picture at right

Incoming search terms:

2004-UP DIGITAL SPEEDOMETER MODULE Owner's Manual

0

Filed Under (Tips and Review) by admin on 26-11-2010

download
SPEEDOMETER INSTALLATION The following procedure details the removal of the factory speedometer and installation of the digital speedometer on Softail models; however the process is similar for all other models: 1. Remove the nut and washer (item #4 in the accompanying exploded view) that secures the console (#5) to the fuel tank. 2. Lay a clean shop rag on the fuel tank and flip the console over to expose the underside of the console. 3. Separate the 12-pin harness connector (#2) from the speedometer. 4. Unscrew the rubber cover from the “trip” reset switch (#6) on t left side of the console. he 5. Remove the “trip” switch from the console. 6. Pry between the three tabs that hold the back clamp (#7) to the speedometer (#1). Remove the back clamp from the speedometer. 7. Remove the speedometer from the console. 8. Remove the gasket (#3) from the speedometer. 9. Installation is the reverse of removal. CHAPTER 3 SPEEDOMETER OPERATION When the motorcycle key switch is ON, the speedometer will enter “normal” mode. Pressing the MODE button will cycle through the following display options: Odometer (ODOM) displays the mileage since the speedometer was installed. Trip (TRIP) displays the mileage since the last time the “trip” button was pressed. Head Temp (H TEMP) displays the cylinder head temperature in degrees F. Battery V (BATT V) displays the battery voltage Fuel (FUEL) displays the fuel level in gallons. Miles Per Gallon (MPG) displays the fuel economy in miles per gallon. Range (RANGE) displays the calculated range (in miles) until the tank reaches its empty value. Horsepower (POWER) to perform the horsepower test, follow these steps

Incoming search terms: