sportster mls head gasket reuse

You search Auto repair manual PDF sportster mls head gasket reuse, if there are search results will appear below. If search results do not exist, please search by others keyword.



  sportster mls head gasket reuse Direct Download speed 5282 Kb/s

  sportster mls head gasket reuse Full Version speed 6162 Kb/s



BMW Motorcycles All R1100 Models- Cylinder Head Gasket

0

Filed Under (BMW) by admin on 16-11-2010

download
Situation: All R1100 models produced from calendar week 18 (April 28, 1997) onwards will be equipped with head gaskets of Multi-Layered Steel (MLS) technology. Service Information: The MLS cylinder head gasket can be used in place of all earlier gaskets, on all R1100 models, without any modifications. Part Number: MSL cylinder head gasket for all R1100 models. P/N: 11 12 1 341 173 Note: The MLS cylinder-head gasket is applicable to R1100 models only. If it becomes necessary to replace cylinder-head gaskets on R850 R models, the conventional gasket, P/N 11 12 1 342 082, must be used. Warranty Processing: If your retail center has any quantity of the conventional head gasket for the R 1100 models, P/N: 11 12 1 342 127, in stock, please file a warranty claim using the information below. If your retail center has the engine gasket set, P/N: 11 00 1 341 901 in stock , please make sure that the new style MLS gaskets are used in place of the conventional head gasket supplied in this set. All current BMW NA inventory of P/N 11 00 1 341 901 will have the MLS head gasket included. Defect Code: 00 11 01 00 00 Frame Number: 4990150 Warranty Type: 2 Warranty Stage: 1 Very truly yours,

Incoming search terms:

Harley Davidson Sportster Straightshots HS Slip-on Exhaust system

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Loosen the heat shield clamps on both the front and rear exhaust pipes. This allows easier access to the head pipe mounting nuts. 2. Loosen, but do not remove, the two head pipe mounting nuts from each flange located at the cylinder head. 3. Remove the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. 4. Loosen the clamp holding the mufflers onto the head pipes. Page 1 of 4 D480IN Rev. 1.0 Sportster Straightshots HS Slip-on Exhaust system Part #16819 U S A Congratulations, you have purchased the finest exhaust system available for your motorcycle. Your VANCE & HINES exhaust system is designed and crafted for maximum performance, a perfect fit, a great sound and unbeatable style! Please follow the installation instructions below and if you have any questions, feel free to call our technical help line (562) 926-5291. Attention Installer: (if other than owner): Please forward this instruction sheet to the purchaser of this product. These instructions contain valuable information necessary to the end user. Tools required for installation: 1/2″ combination wrench 3/8″ drive ratchet and 9″ extension 9/16″ and 1/2″ sockets 5/16″ Nutdriver/flat blade screwdriver 5. Remove the two bolts from each muffler which attach the mufflers to the mounting bar. 6. Remove the mufflers by sliding them off the head pipes. 7. Remove the clamp from the nose of each muffler (these will be re-used when installing the new mufflers). 8. Remove the gaskets from the crossover ports on the stock mufflers. Inspect the gaskets and replace if damaged or worn (H-D part #65927-00). 9. Install crossover gaskets onto mounting bar on motorcycle. VANCE & HINES EXHAUST SYSTEM INSTALLATION 1. Remove mufflers and heat shields from protective packaging. 2. Slide the nut plate inside the bracket that is welded to the backside of each muffler body and attach the muffler bodies to the mounting brackets (stamped 379-P) using four 5/16″ x 5/8″ flange head bolts (supplied). Leave them loose at this time (Figure 1). 3. Slide stock exhaust clamp onto nose of each muffler. 4. Slide mufflers onto head pipes and align crossover port with gasket on mounting bar (Figure 2). Press into place on gasket. 5. Attach the muffler brackets to the stock mounting bar using four 5/16″ x 3/4″ hex head bolts, washers, and nuts (supplied). Leave them loose at this time (Figure 3). 6. Tighten cylinder port exhaust flange nuts on front and rear cylinders. 7. Install and tighten the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. 8. Align muffler and bracket so they sit level. Tighten the muffler mounting bolts and the bracket mounting bolts. 9. Tighten the clamp holding the muffler onto the head pipe.

YAMAHA VIRAGO 700/ 1100 2 into 2 EXHAUST SYSTEM REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the slip joint clamp on the front and rear head pipe, which are located at the muffler box. 2. Remove the two nuts that hold the front head pipe to the engine. Slip the head pipe out of the muffler box and set it aside. Note: Do not remove the rear head pipe, it has been incorporated in the design of the new exhaust system. 3. Remove the muffler box mounting bolt located in front of the passenger foot rest on the left side. 4. Remove two bolts from the right passenger foot rest assembly and set the foot rest aside. 5. Slide the muffler box off of the rear head pipe and set it aside. 6. Replace the muffler box mounting bolt (from step #3) using the washer and nut (supplied) on the back side. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Attach the mounting bar to the motorcycle frame behind the right passenger foot rest. Align the two holes in the largest bracket on the mounting bar with the two holes on the frame, be sure the bend in the mounting bar is pointing to the center of the motorcycle. 2. Install the round steel spacer (supplied) to the rear most hole in the bracket. 3. Attach the foot rest using the two 8mm x 1.25 x 25mm bolts (supplied). 4. Slide the new exhaust flange (supplied) onto the front head pipe. 5. Install the two heat shields to the front head pipe using the four hose clamps (supplied). Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the heat shields onto the front head pipe. Note: Be sure the bend in the heat shield matches the bend in the head pipe exactly. Wrap the hose clamp around the head pipe and give the screw three to four turns, leaving heat shield loose on the head pipe. Repeat this step with the heat shield on the rear head pipe. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 6. Check the stock exhaust gaskets to be sure they are in good shape. If you have any doubts as to their condition, replace them. 7. Slide a chrome pinch clamp (supplied) onto the expanded end of the new rear head pipe. Install a 3/8″ x 1″ bolt with a flat washer on either side of the clamp followed by a lock nut (hardware supplied). Repeat this step on the inlet end of each muffler using the two muffler clamps with 5/16″ x 1 1/4″ bolts (hardware supplied) but leave the clamp loose at this time. 8. Slip the new rear head pipe with the heat shield attached, over the stock rear pipe and gasket, but leave the clamp loose at this time. 9. Install the front head pipe, with the heat shield attached and stock gasket in place, to the front cylinder using the stock nuts, leave them loose at this time

Incoming search terms:

2009 Daytona 675 Motorcycle Race Kit Manual

0

Filed Under (Triumph) by admin on 29-10-2010

download
1. Remove the existing cylinder head gasket in line with the procedures detailed in the Daytona 675 service manual. 2. Position a piece of solder (with a diameter approximately 1.3 mm) on the four squish surfaces of each piston. Position the solder in line with the corresponding squish surfaces on the cylinder head and hold in place with a small amount of grease. 3. Refit the cylinder head with the head gasket. 4. Slowly turn the engine over, by hand, to compress the solder to the same height as the squish clearance. 5. Remove the cylinder head and head gasket. 6. Measure the compressed thickness of the solder. The squish clearance must be a minimum of 0.65 mm. If the thickness of the solder is less than 0.65 mm repeat steps 2 to 6 with a thicker head gasket until the squish clearance is at an acceptable level. NOTE •In some cases, it may be necessary to use a standard cylinder head gasket to achieve the correct squish clearance. 7. Fit the chosen cylinder head gasket following the procedures detailed in the Daytona 675 service manual. Warning Running the engine at less than the minimum recommended squish height can lead to the pistons contacting the cylinder head, causing major engine damage. This could cause loss of motorcycle control and an accident. Triumph Designs Ltd 2009. Camshaft, Valve Spring & Camshaft Sprocket Kits Parts Supplied Camshaft, Inlet – A9618055 Camshaft, Exhaust – A9618056 Valve Spring Kit – A9618086 Camshaft Sprocket Kit – A9618095 Warning The Race Kit camshaft, valve Spring and camshaft sprockets must be fitted as a complete set. If they are not fitted as a complete set a failure may result which could cause loss of motorcycle control and an accident. Caution The use of The Race Kit camshaft, valve Spring and camshaft sprockets detailed below will require changes to the fuelling and ignition settings. To alter these settings, a Triumph Programmable Race ECU combined with Triumph TRACS Race Calibration Software will be required. Failure to correct the fuelling and ignition settings will result in poor engine performance and could result in engine damage.

KAWASAKI VULCAN 700/750 CRUZER EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 28-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Place the bike on the center stand. 2. Remove the three clamps attaching the heat shield to the left hand head pipe and set the heat shield aside. 3. Remove the two heat shield clamps attaching the heat shield to the right hand head pipe and set the heat shield aside. 4. Loosen the pinch clamps where the mufflers slip onto the muffler box (the black box in front of the rear tire). Remove the bolt attaching the mufflers to the footrest. 5. Remove the left and right hand mufflers and set them aside. 6. Remove the right hand foot rest and brake pedal assembly from the frame. 7. Loosen the pinch clamps where the head pipes slip into the muffler box. 8. Remove the two nuts that secure the right head pipe to the cylinder head. Repeat this step on the left head pipe and save the nuts for reuse. 9. Remove the left and right hand head pipes. Remove the header flange from each head pipe and save the two flanges for reuse. Set the head pipes aside. 10. Remove the two bolts (one on each side) that mount the muffler box to the frame. Lower the muffler box down and set it aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Remove the two bolts from the charcoal canister mount, the canister is located in front of the rear tire. Using the two 6mm x 16mm bolts (supplied) install the centerstand stop bracket, (stamped 205), by aligning the holes in the bracket with the holes in the canister mount. Be sure the bend closest to the holes in the bracket angles towards the rear of the motorcycle and the tang is pointed to the left hand side. Tighten the two 6mm bolts at this time. 2. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Place the front head pipe into the heat shield, wrap the hose clamp around the head pipe and give the screw three to four turns. Repeat this step with the rear heat shield. Note : The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. Leave them loose at this time. 3. Install a three hole mounting bracket to each muffler as shown in figure 1. Slide one dog bone shaped nut plate under the bracket that is welded to the backside of each muffler. Attach the mounting bracket using two of the 5/16″ flange head bolts (supplied), leave them loose at this time. Note : The muffler bracket stamped #284 is for the right hand muffler, bracket #285 is for the left hand muffler. 4. Install the rear exhaust assembly, with the heat shield attached, to the rear cylinder using the stock flanges and nuts. Install the stock muffler mounting bolts through the rear footrest brackets, the supplied muffler brackets, and finger tighten the nuts. Leave them loose at this time. 5. Repeat step #4 with the front head pipe

HARLEY DAVIDSON AUTOMATIC COMPRESSION RELEASE TOOLS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
INSTALLATION Compressed air can pierce the skin and flying debris from compressed air could cause serious eye injury. Wear safety glasses when working with compressed air. Never use your hand to check for air leaks or to determine air flow rates. (00061a) Wear safety glasses or goggles while drilling. Flying debris could result in serious eye injury. (00565b) 4 3 6 5 6 1 2 7 is05443 1. Drill, 1.250 inch 2. Drill stop collar, 1.250 inch 3. Drill stop gauge 4. Socket head screw, 5/16 inch 5. Socket head screw, 1/4 inch 6. Dowel pin 7. Top plate Figure 1. Top Plate and Drill Bit Stop Collar Installation 1. Remove valves from cylinder heads. NOTE Do not allow the threaded studs to damage the gasket sealing surface of the cylinder head. 2. See Figure 7 and Table 1. Mount a cylinder head to the tooling plate (1). 3. Place a head bolt spacer (7) over each stock head bolt and lubricate threads and thrust faces, dowels and studs. Tighten head bolts in a crisscross pattern to 10 ft-lbs (13.5 Nm) . 4. See Figure 1. Align the top plate (7) bolt and dowel holes with the head hole pattern, Screamin’ Eagle logo towards the spark plug. This plate will only fit one way for the cylinder head it is being installed on. If the plate does not align with the head, turn it over keeping the logo towards the spark plug and install the cylinder head. 5. Lubricate the two dowel pins (6) and insert in the top plate and into the cylinder head. 6. Apply lubricant to the two socket head screws (4 and 5). Insert into their respective holes in the plate to the cylinder head and tighten to 5 ft-lbs (6.8 Nm)

Incoming search terms:

Kawasaki 900/1100 Billet Head Installation And REMOVAL Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Remove stock head and clean the top surface of the cylinder. 2) Remove the stock water fitting from the stock head and install it in the ADA Racing® billet head in the center cylinder location. Install the 1/8″ npt brass plugs in the 2 outer cylinder locations. 3) Install all o’rings in the ADA Racing® billet head, use small amounts of grease to hold them in place, do not use super glue or silicone. 4) Apply a small amount of grease to the small (OR020) o’ring at the top of the dome. This will allow the dome to easily slip into the head shell. Be careful when turning the head upside down to install onto the cylinder, as the domes can slide out of the head shell. 5) Make sure all the o’rings are in place and place the head on top of the cylinder with the water outlet on the intake side. You must be sure that none of the o’rings slip out of their groove, as this will cause an o’ring to get pinched and a water or compression leak could result. 7) Torque all of the nuts to 15ft/lbs, in a center-out criss-cross pattern. Now, torque them again to 18ft/lbs. 8) After the 1st time out riding the head should be re-torqued. 9) The 2 additional 1/8″ npt holes in the ADA Racing® billet head come with brass plugs, but barbed fittings can be installed for custom water routing applications.

Incoming search terms:

Harley davidson Sportster Custom Straightshot Exhaust System REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the heat shield clamps on both front and rear exhaust pipes. 2. Remove the two mounting nuts from each head pipe, located at the cylinder head. 3. Remove the nut that mounts the front muffler to the engine, located below the rear brake master cylinder. 4. Remove the bolt that mounts the rear muffler to the mounting bar. 5. Remove the entire exhaust system and set it aside. 6. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. Note: If circlips look bent or twisted replace them with new circlips . INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Vance and Hines recommends you replace your exhaust gaskets with Sceamin’ Eagle gaskets part number 17048-98. 2. Install the circlips and flanges from the stock system on to both of the new head pipes. 3. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edge of both heat shields with the location of the mounting clips that are welded to the backside. Position the front heat shield over the head pipe and feed the tail end of the hose clamps into the clips. Be sure that each hose clamp is engaged with both clips. Repeat this step with the rear heat shield. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 4. Install the front head pipe using the stock nuts, do not tighten at this time. 5. Install the rear head pipe using the stock nuts, do not tighten at this time. 6. Install one muffler clamp (supplied) over the inlet (notched end) of each muffler. 7. Identify the front and rear muffler mounting brackets. The front bracket is stamped with the number 305 and the rear muffler bracket is stamped 213 . 8. Install the front muffler mounting bracket to the stud on the engine (where the stock muffler mounted) and fasten using the stock nut (leave loose at this time). The bracket will bend inward towards the center of the motorcycle when installed correctly. Note: You may need to move the wires and hoses on the lower frame rail to decrease the possibility of them chaffing on the bracket bolts. 9. Slip one of the mufflers onto the front head pipe. Slide one dog bone shaped nut plate (supplied) under the bracket that is welded to the backside of the muffler. Attach the muffler to the mounting bracket using the 5/16″ flange head bolts (supplied) leave them loose at this time. 10. Attach the rear mounting bracket to the rear muffler. Slide one dog bone shaped nut plate (supplied) under the bracket that is welded to the backside of the muffler. Attach the bracket to the muffler using two of the 5/16″ flange head bolts (supplied), leave them loose at this time. Note: The single hole in the bracket will point downward and slightly forward when installed correctly

Yamaha Road Star 1600/ 1700 Exhaust kit bill of materials Installation Instructions

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Remove left side cover, by removing allen bolt as shown (Fig 1). Once bolt is removed, push cover to motor and push back carefully to your upper body. Figure 1 2. Once left side cover is removed, remove 6mm bolt to opposite side cover as shown (Fig. 2). Also remove allen bolt on right side as shown (Fig 3) and remove carefully . Figure 2 Figure 3 . Remove two allen bolts to the muffler bracket, and also loosen hose clamp to bottom head pipe. (Fig 4 & 5) Figure 4 Figure 5 4. Remove bolt next to rear O/2 sensor bracket as shown (Fig 6), also remove Phillips head bolt from O/2 bracket and slide O/2 sensor off bracket as shown (Fig 7). Once bracket is removed mount just bracket on with Phillips head bolt back on. Figure Figure 7 5. Disconnect O/2 by using a pick on inside switch on opposite side of O/2 bracket. With pick on inside push to you and unplug. (Fig 8 & 9) Figure 8 Figure 9 6. Remove two socket cap nuts from rear head pipe flange as shown (Fig 10). Once removed, remove both mufflers and rear head pipe carefully. Slide muffler back and shift rear head pipe to you. (Fig 11) Figure 10 Figure 11 7. Slide wire off bracket from the front O/2 sensor as shown (Fig 12). Also use pick to remove O/2 sensor, push to you and unplug. Figure 12 Figure 13
8. Remove two allen bolts from foot rest/ brake to give you access to head pipe. (Fig 14) Figure 14 9. Remove two allen socket cap nuts off front head flange and remove head pipe. (Fig 15) Figure 15 10. Remove stock muffler bracket by removing two alien bolts as shown (Fig 16). Also remove bolt that holds stock bracket to the brake line (Fig 17). Once that is done remove brake line from caliper and slide though muffler bracket and re-install. Figure 16 Figure 17
Assembly 11. Remove O/2 sensor from stock pipe and install O/2 sensor in Roadhouse front head pipe and mount front head pipe with stock socket cap nuts on bike as shown. (Fig 18 & 19) Figure 18 Figure 19 12. Mount rear head pipe as shown (Fig 20), including stock socket cap nuts. Also mount y-collector with rear head pipe. Y-collector must slide into front head pipe in one. Install Roadhouse O/2 sensor wire lead from hardware kit into y-collector. (Fig 21) Figure 20 Figure 21

Incoming search terms:

Kawasaki Ultra/ STX-R Billet Head Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Remove stock head and clean the top surface of the cylinder. 2) Remove the stock water fittings from the stock head and install them in the ADA head in the same order. 3) Install all o’rings in the ADA billet head, use small amounts of grease to hold them in place, do not use super glue or silicone. 4) Apply a small amount of grease to the small (OR020) o’ring at the top of the dome. This will allow the dome to easily slip into the head shell. Be careful when turning the head upside down to install onto the cylinder, as the domes can slide out of the head shell. 5) Make sure all the o’rings are in place and place the head on top of the cylinder with the water outlets on the top side. You must be sure that none of the o’rings slip out of their groove, as this will cause an o’ring to get pinched and a water or compression leak could result. 6) Use the additional 8mm flat washers on the taller studs, along with the stock wash- ers. 7) Torque all of the nuts to 15ft/lbs, in a center-out criss-cross pattern. Now, torque them again to 18ft/lbs. 8) After the 1st time out riding the head should be re-torqued

Incoming search terms: