sportster tail light wiring 3 wire to 2 wire

You search Auto repair manual PDF sportster tail light wiring 3 wire to 2 wire, if there are search results will appear below. If search results do not exist, please search by others keyword.



  sportster tail light wiring 3 wire to 2 wire Direct Download speed 5282 Kb/s

  sportster tail light wiring 3 wire to 2 wire Full Version speed 6162 Kb/s



YAMAHA ROADLINER AND STRATOLINER LAY DOWN LICENSEPLATE/ TAIL LIGHT INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 29-01-2011

download
1. Remove the license plate. Remove the license plate holder assembly from the rear fender (three 8mm Allen bolts 5mm wrench). Remove the five 4mm Allen screws underneath the rear fender which secure the taillight/turn signal assembly to the rear fender (3mm wrench). As shown in photo #2, pull the taillight assembly out away from the fender, turn it over, place a towel or rag between the light and fender and allow it to rest on the fender. 2. Locate the supplied triangular license plate mounting block, two 8 x 20mm Allen screws with holes driiled thru and three rubber washers. Place the two Allen screws thru the upper holes in the block and the rubber washers over the screws on the backside of the block. Start the screws into the upper holes on the fender. Use one of the three screws removed earlier from the original mount in the remaining lower hole of the new block sliding the remaining rubber washer between the block and fender. Tighten all three Allen screws secure enough to compress the rubber washers (4-6 ft lbs.). 3. Locate the supplied license plate mounting plate and LED lights. Cut off the excess red and black wires at the end of the black loom or tube. Referring to photo (1) thread the wires of the LED lights thru the small holes in the mounting plate, peel the cover from the adhesive backing on the lights and press them firmly into place as shown. 4. Locate the three supplied ¼” x ½” flat head Allen screws. Hold the plate up to the mounting block installed earlier with the wires at the bottom of the plate. Thread the wires from the LED lights thru the holes in the upper bolts of the block. Install the plate onto the block using the three flat head screws being sure to keep the exposed wire behind he plate as short as possible and fitting into the slot or cut out at the edge of the block. Snug the screws and again check to see tat the wires are in the slot or cut out in the block and do not become pinched as the screws are tightened. Tighten the screws securely. 5. Where the wires from the taillight go thru the fender there is a grommet, pull this grommet out from the fender. Thread the wires from the LED lights thru the grommet with the other wires. Replace the grommet into the fender and remove any slack from the wires under the fender. Cut the LED wires off at 6″ past the grommet. 6. Referring to photo (2) remove 2″ of the black tubing exposing the red and black wires on the LEDs. Locate the supplied brake/tail light dual function element (a red wire at one end with a red and orange wire at the other) and wire connectors. Cut all three wires on the dual element to 3″ long. Strip the end of the single red wire on the element and both of the red wires from the LEDs then connect them using one of the blue butt connectors. Connect the two black wires from the LEDs to any one of the black wires on the tail light or signals using one of the supplied splice connectors (place both black wires into one of the holes on the connector). Using the remaining splice connectors attach the red wire from the dual element to the yellow wire on the tail light and the orange wire to the blue wire on the tail light. Turn on the ignition and check that the LEDs are working both as tail and brake lights when the brakes are applied.

HARLEY DAVIDSON TOUR-PAK RACK LIGHT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
INSTALLATION 1. Remove all contents from Tour-Pak®. 2. For easier installation, remove Tour-Pak rack, if installed, by removing cap screw, washers and mounting pads. 3. See Figure 1. Remove rubber plug from bottom rear rail on left side of rack. 4. See Figure 2. Use line wire feeder in kit to thread through left rear rack foot and out through the back opening of rail. 5. Attach light harness wires to line wire feeder loop. 6. Carefully pull line wire feeder and light harness wires through rack mounting foot. 7. See Figure 5 and Table 1. Apply foam pads (5) to top surface of light. 8. Secure light (1) to rack with socket head screws (4) and washers (6). 1 is05242 1. Plug Figure 1. Left Side Rack Plug 1 is05244 1. Line wire feeder Figure 2. Thread Wires Through Rack 9. Position rack/light assembly to Tour-Pak lid and route wires through lid, washer and hollow mounting bolt. 10. Attach rack/light assembly to Tour-Pak using instructions and hardware provided with rack except for use of hollow bolt from Step 9. 11. Remove Tour-Pak liner. 12. Thread wires through black vinyl conduit. 13. Ultra Classic models: Follow Steps 14 through 2114. Locate and disconnect three pin AMP connector for Tour- Pak lights. 15. See Figure 3. Attach the Y-harness (2) to the three pin male connector (1) of Tour-Pak harness. 16. Route light wires from back of Tour-Pak along left side to front. Secure conduit with adhesive clips provided in kit. 17. Trim length of light wires and conduit to reach Y-harness. 18. Refer to the Service Manual electrical appendix to install terminal pins (8) to rack light wires and install terminals to three pin housing (7) as follows: a. #1 cavity = blue lead b. #2 cavity = red with yellow lead c. #3 cavity = black lead 19. Connect rack light to remaining Y-harness connector. 20. Replace Tour-Pak liner. 21. Check operation of Tour-Pak tail and stop light functions before operating motorcycle. 22. Classic models: See Figure 4. If necessary, drill hole in lower left bottom of Tour-Pak and install grommet. Route rack light wires through grommet. 23. Refer to the Service Manual electrical appendix to install terminal receptacle (8) to rack light wires and install terminals to three pin receptacle housing (7) as follows: a. #1 cavity = blue lead b. #2 cavity = red with yellow lead c. #3 cavity = black lead NOTE To prevent corrosion, fill the cavities of the connectors with dielectric grease (included in kit) prior to making connections. As an additional precaution against moisture seepage into the Tour-Pak, apply silicone sealant (not included in kit) to the entrance of the light harness wire tunnel. See figure 2 for location reference. 24. Connect rack light to male connector of two connector wire harness (12) and connect to accessory connector under seat. 25. Replace Tour-Pak liner. 26. Check operation of Tour-Pak tail and stop light functions before operating motorcycle

Incoming search terms:

HARLEY DAVIDSON TRI-BAR AUXILIARY RUNNING LIGHT/ BRAKE LIGHT ASSEMBLY REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
REMOVAL 1. Remove the saddlebags and left side cover. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. Remove the main fuse. 3. See Figure 1. Remove six flange nuts (1) from the right and left fender stud plates (2). 1 2 3 5 4 is04366a 1. Nut 2. Stud plate 3. Rear fascia 4. TORX screw 5. Lamp assembly Figure 1. FLHX Rear Fascia and Lamp 4. On the left side of the motorcycle, loosen the set screw and unscrew the radio antenna mast. 5. Gently open the adhesive conduit at the split line to release the rear fascia light harness. 6. At the rear of the motorcycle, spread the top of the fascia to release from the top studs at the side of the fender and then pull the bottom in a downward direction to release the fascia from the fender. If necessary, gently wiggle the fascia while pulling. 7. 2006-2008 models only: On the left side of the motorcycle, remove the bolt (with flat washer) to remove the passenger seat strap and saddlebag front mounting bracket from the chrome frame tube cover. 8. Remove the screw and chrome frame tube cover. NOTE ALL models: Make note of the wire routing and location of all cable straps. New light wiring installs the same way. 9. See Figure 2. Release the rear fascia light wires from the wire clip (1). Cut the cable straps (2) to release the rear fascia light harness (3) and radio antenna cable. 10. 2006-2008 models: Disconnect the rear fascia light connector [12B] located inboard of the upper frame tube. 2009 and later models: Disconnect the rear fascia light connector [12B] located to the rear of the fuse panel. 11. See Figure 1. Remove the two T-20 TORX® screws to release the light assembly from the fascia. Save the screws for installation of the new light. 1 3 4 2 is04378 1. Wire clip 2. Cable strap 3. Fascia light harness 4. Flange nut Figure 2. Rear Fascia Light Harness INSTALLATION 1. Route the rear fascia light wires forward through the cable clip at the top of the radio antenna bracket and then upward in front of the saddlebag rear mounting bracket to the inboard side of the upper frame tube. 2. 2006-2008 models: On the inboard side of the upper frame tube, mate the pin and socket housings of the rear fascia light connector [12]. 2009 and later models: To the rear of the fuse panel, mate the pin and socket housings of the rear fascia light connector [12]. 3. Using the slotted hole, install a new cable strap to secure the rear fascia light wires and radio antenna cable to the rear fender support. 4. Install a new cable strap to secure the rear fascia light wires and radio antenna cable to the shoulder of the upper frame tube (just in front of the air valve mounting bracket).

Incoming search terms:

SR-C400 Motorcycle Security System INSTALLATION MANUAL AND USER'S GUIDE

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Routing the Antenna Wire The MCM includes an 18″ antenna wire. The first 12″ is a coaxial wire; the remaining 6″ is the reception antenna wire. When routing, try to avoid running the antenna along or near metal. For best performance, have the antenna wire as vertical as possible and exposed. Wire Connections The system includes one harness (HAR-1a) that connects directly into the MCM. The harness is split into three plugs: one for the GEN-1a connector, one for the optional SN-5 connector and one for the data output for future expansion. Note: Each plug is unique and will only fit the appropriate component one way. Main Harness Note: If the optional factory connector kit is being used, please disregard this section of the instructions and refer to the instructions supplied with the factory connector kit. The main harness consists of two harnesses. One is labeled (HAR-1a) and the second is labeled (GEN-1a). Plug in the white 4 pin connector from the (HAR-1a) into the matching 4 pin connector from the (GEN-1a). The (HAR-1a) also has a waterproof connector that plugs into the MCM. The wires should be connected as follows: HAR-1a Black wire with fuse and ring terminal – To battery Positive (+). GEN-1a Black wire – To ground (-). Orange wire – To tail light wire or any other wire that is hot (+) when ignition is ON (NOTE: this is an input to the alarm this connection is not designed to flash the tail light). Color Codes: Ground (-) Tail Light Honda Green wire Brown wire Kawasaki Black wire Red wire Suzuki Black/White Brown wire Yamaha Black wire Blue wire Harley Davidson Black wire Blue wire

Incoming search terms:

Power Grid LED Integrated Tail Light General Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Running Light, Brake Light and Blinker Function The triple wire harness plugs directly into the OEM wire harness designed for the stock tail light. Optional integrated turn signals are designated by Yellow and Blue wires coming off of the harness connected to the DMP LED Integrated Tail Light. If you are sitting on the bike the yellow wire connects to the right side blinker and the blue wire connects to the left side blinker. Installation DMP LED Integrated Tail Lights are designed to replace the OEM factory unit with the use of OEM original hardware. Pay close attention during the disassembly process to ensure proper assembly later. Tip: During disassembly it might be useful to use a small digital camera or camera phone to remind the installer where things go in conjunction with the OEM factory service manual. Test Function NOTE: Double check before you test the functionality of your new DMP tail light, make sure there are no crossed or short circuited connections before you reconnect the battery. If your new DMP tail light is not operating properly please check all your connections thoroughly

HARLEY DAVIDSON DETACHABLE QUARTER FAIRING AND DOCKING HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
Installation The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley- Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE If your motorcycle has directional lights mounted on the upper fork bracket they must be relocated to the bottom fork bracket. Some models have front directional lights equipped with three wires, the third black wire is a ground wire. Check to determine how many wires are connected to the front directional lights and follow the following procedure that applies. Ifdirectional lights are not mounted on the upper fork bracket proceed to “ASSEMBLING FAIRING”. Relocating Two Wire Directional Lights 1. Support motorcycle on a center stand such that front wheel is raised slightly off the ground. 2. Remove fork tube pinch screw from right side of lower bracket. 3. Cut wires connected to right directional light about 2 in. away from directional light body. 4. Remove fork tube pinch screw from right side of upper fork bracket. (This is the screw that secures the right directional light.) 5. Install right directional light on right side of lower fork bracket using pinch screw removed in step 4. Install pinch screw removed in step 2 into right side of upper bracket. Tighten both pinch screws to 30-35 ft-lbs. 6. Repeat steps 1 through 5 to relocate left directional light. NOTE Fork tubes may slide downward within fork brackets. If this occurs, front fork tube extension above front fork upper bracket will have to be readjusted according to appropriate Service Manual procedures. 7. Connect the right directional light as follows: Strip approx. 5/16 in. of insulation from the wires cut in step 3. 8. Crimp solderless connectors from kit on two wires coming from motorcycle. 9. Split one end of the 2-conductor polarized wire from kit back about 2 in. and strip 5/16 in. of insulation from wire ends. 10. Slide a piece of shrink tubing from kit over each of the wire ends stripped in step 9 and crimp the wires into the terminals installed in step 8. Make sure you connect the silver and copper colored wires to like colored wires. NOTE Polarized wire is used in this application to ensure correct wiring. One wire is silver, one is copper colored. Wire colors of spliced wire must match wire color of original directional wire leads. 11. Cut polarized wires to the length required for connection to the wires at the relocated directional light. Make certain you leave enough slack in wires to allow routing the harness along the fork tube. 12. Split remaining end of the 2-conductor polarized wire from kit back about 2 in. and strip 5/16 in. of insulation from wire ends. 13. Slide heat shrink tubes over the two wire end. 14. Strip 5/16 in. of insulation from wires connected to directional light and connect like colored wires at directional light with connectors from kit. 15. Slide heat shrink tubing over connectors installed in steps 10 and 14. Activate shrink tubing with heat gun or hair dryer.

HARLEY DAVIDSON TRIBAR LED TAIL LIGHT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 28-02-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Remove main fuse. Refer to service manual for location. 2. Remove seat using service manual instructions. 3. Remove rear tail light using service manual instructions. 4. Remove rear turn signals using service manual instruc- tions. 5. See Figure 1. Clip the cable strap (1) to free the rear harness from the chassis seat pan. 6. Unplug the 8-place connector (2) from the rear harness connector. 1 2 is05510 1. Cable strap 2. Harness connector Figure 1. Rear wire harness 1 2 4 3 is05511 1. Screws 2. Fender cover 3. Frame rail 4. Mounting bracket Figure 2. Remove Fender NOTE The fender support covers do not have to be removed from the upper shock absorber bolts. 7. See Figure 2. Remove the two rear fender support cover screws (1) and remove covers (2) and fender mounting -J04721 bracket (4). Repeat for opposite side and carefully remo ve fender and place it on a non-scratch surface. 8. See Figure 3. Clip and remove two cable straps (1). Pull wire harness three inches towards the license plate bracket. 9. Remove flange nuts (2) from both sides of license/tail light bracket stud plates (3) and remove bracket. Save stud plates and flange nuts. 1 3 2 is05517 1. Cable straps 2. Flange nuts 3. Stud plates Figure 3. Rear Harness Cable Straps, Flange Nuts and Stud Plates 10. Install new license/tail light bracket using stud plates and flange nuts previously removed. Tighten nuts to 5-6 ft-lbs (6.8-8.1 Nm) . 11. See Figure 2. Install rear fender by installing two screws (1) on each side through the fender support covers (2), frame rails (3) and into the fender mounting brackets (4). Tighten to 12-18 ft-lbs (16.3-24.4 Nm) 12. See Figure 1. Connect rear harness connector to 8-place connector on main harness. 13. Use a large cable tie strap from kit to secure the rear harness to seat pan. 14. Install rear turn signal lights using service manual instructions. 15. Verify that there is no excess wire harness near the stud plate then secure the harness with a large cable strap where the straps were previously removed. 16. See Figure 4. Secure the turn signal harness (3) to the stud plate (1) using small cable strap (2) and route the turn signal wire through the tail light bracket clip (4) as shown.

HARLEY DAVIDSON TOUR-PAK SPOILER LIGHT KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-03-2011

download
Installation 1. If the motorcycle was previously equipped with a Tour-Pak Spoiler Light, disconnect the light wires from the motorcycle. 2. Remove the Tour-Pak Spoiler from the Tour-Pak and disassemble original light or chrome trim (as equipped). Save the original mounting hardware for later installation. 3. Attach light assembly to spoiler using 10-24 x 7/8 in. long screws. 4. See Figure 1. Route light wires through 3/8 in. hole in Tour-Pak lid. Attach spoiler to Tour-Pak lid using original hardware removed in step 2. 5. See Figure 1. Attach the wires to the inside of the Tour- Pak with adhesive backed clips as shown. Route wires out front left corner of Tour-Pak bottom and support wires inside Tour-Pak bottom with the remaining adhesive backed clips as needed. Wires will exit out the bottom of the Tour-Pak through the antenna cable grommet. NOTE On Chopped Tour-Paks drill a 3/8 in. hole in the front left corner of the Tour-Pak bottom. Route the spoiler light wires through this hole for connection to the main motorcycle wiring. 6. On 1994 and later models, proceed to step 7 for wire connection instructions. On 1993 and earlier models, go to step 11 for wire connection instructions. WIRING INSTRUCTIONS FOR 1994 AND LATER MODELS 7. Remove the seat and locate the accessory circuit connector. Route the light wires along the frame and secure with cable straps from kit. 8. Refer to the Deutsch connector section in a 1994 or later FLT Service Manual and assemble the spoiler wires into the socket connector half supplied with the LED assembly. The wire terminals shall be inserted in the connector half as follows: WIRE COLOR CODECONNECTOR CAVITY Blue 1 Red/yellow 2 Sealing plug 3 Black 4 9. Remove the plug from the accessory connector located under the seat (connector number [4A] in wiring diagram in Service Manual). Connect wire from spoiler. Turn on ignition switch and test the spoiler light operation with taillight and brake light. 1 WARNING Always connect the positive battery cable first. If the positive cable should contact the ground with the negative cable installed, the resulting sparks may cause a battery explosion resulting in personal injury. 10. Reattach battery

2002-2005 Honda VFR800/A Wire Harness Replacement Manual

0

Filed Under (Honda) by admin on 21-04-2011

download
If the 18P (light blue) connector is in abnormal condition as shown below, contact TechLine at (800) 421-1900, option 9. FRONT SUB-HARNESS REPLACEMENT 1. Remove the front sub-harness from the cowl stay hooks. Disconnect all the electrical components from the front sub-harness. 2. Temporarily set the main wire harness aside, and disconnect the 6P (natural) con- nector. Then, carefully remove the front sub-harness. 3. Install the new front sub-harness by con- necting the 14P (natural) and 18P (light blue) connectors. NOTE: For routing specifications, refer to the WIRING & HARNESS ROUTING SECTION on pages 7-8. 4. Attach the front sub-harness on the cowl stay hooks. Make sure the front sub-harness is routed elow the main sub-harness. ABNORMAL CONDITION STAY HOOKS 6P (NATURAL) CONNECTOR FRONT UB-HARNESS 14P (NATURAL) CONNECTOR 18P (LIGHT BLUE) CONNECTOR FRONT SUB-HARNESSSTAY HOOK Page 4 VFR800/A #4 4 of 12 NOVEMBER 2007 5. Place the front sub-harness between the radiator and the frame, and below the rec- tifier. Be careful not to damage the front sub-harness or other components. 6. Re-connect the front sub-harness to the 6P (natural) connector. 7. Secure the main wire harness and the front sub-harness using the longer wire band. 8. Secure the main wire harness and the upper side of the front sub-harness using the shorter wire band. Adjust the wire har- ness located within the frame and the radi- ator hose accordingly. 9. Secure the main wire harness fuse box to the front sub-harness using the shorter wire band. FRONT SUB-HARNESS STAY HOOK MAIN-HARNESS FRONT SUB-HARNESS FRONT SUB-HARNESS 6P CONNECTOR (Male) 6P CONNECTOR (Female) WIRE BAND (LONG) WIRE BAND (SHORT)
WIRE BAND (LONG) WIRE BAND (SHORT) MAIN WIRE HARNESS FUSE BO

Incoming search terms:

YAMAHA YZF-R1R/ YZF-R1RC OWNER'S MANUAL

0

Filed Under (Yamaha) by admin on 03-12-2010

download
1. Right turn signal indicator light “” 2. Fuel level warning light “” 3. Oil level warning light “” 4. Neutral indicator light “” 5. Engine trouble warning light “” 6. High beam indicator light “” 7. Left turn signal indicator light “”
INSTRUMENT AND CONTROL FUNCTIONS 3-3 3 EAU04895 Oil level warning light “” This warning light comes on when the engine oil level is low. The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical cir- cuit. NOTE: Even if the oil level is sufficient, the warning light may flicker when riding on a slope or during sudden acceleration or deceleration, but this is not a malfunction. This model is also equipped with a self-diagnosis device for the oil level detection circuit. If the oil level detection circuit is defective, the following cycle will be repeated until the malfunction is corrected: The oil level warning light will flash ten times, then go off for 2.5seconds. If this occurs, have a Yamaha dealer check the motor- cycle. EAU00061 Neutral indicator light “” This indicator light comes on when the transmission is in the neutral position. EAU04896 Engine trouble warning light “” This warning light comes on or flashes when an electrical circuit monitoring the engine is defective. When this occurs, have a Yamaha dealer check the self-diagnosis system. (See page 3-7 for an explanation of the self-diagnosis device.) The electrical circuit of the warning light can be checked by turning the key to “ON”. If the warning light does not come on for a few seconds, then go off, have a Yamaha dealer check the electrical circuit. EAU00063 High beam indicator light “” This indicator light comes on when the high beam of the headlight is switched on

Incoming search terms: