sproket noise on 71 shovehead

You search Auto repair manual PDF sproket noise on 71 shovehead, if there are search results will appear below. If search results do not exist, please search by others keyword.



  sproket noise on 71 shovehead Direct Download speed 5282 Kb/s

  sproket noise on 71 shovehead Full Version speed 6162 Kb/s



TOYOTA ALL MODELS AM STATIC NOISE ON VEHICLES WITH POWER ANTENNAS

0

Filed Under (Toyota Manuals) by admin on 16-10-2011

download
Vehicles with power antennas may exhibit audible electrical noise on weak AM stations when various electrical accessories (turn signals, rear defogger, cruise control, brakes, etc.) are operated. Poor antenna grounding can cause this condition. To eliminate or reduce the intensity of the noise, use the following repair procedure: AM STATIC NOISE ON VEHICLES WITH POWER ANTENNAS Page 1 of 2 OCTOBER 25, 1996 AUDIO AU002-96 ALL MODELS REPAIR PROCEDURE: 1. Tune the radio to a strong, static-free AM station and slowly move the tip of the antenna
mast forward and back approximately 2 inches (Fig. 1). If static noise is not heard, go to Step 2. If static noise is heard during antenna movement, replace the antenna mast and go to Step 3. NOTE: Do not touch the antenna mast with your bare hands. Use a glove or nonmetallic object to move the antenna. (If you touch the antenna with your hands, you will change the antenna sensitivity). 2. Remove the antenna mast and inspect the base of the mast for corrosion and damage (Fig. 2). Clean with 1500 grit sandpaper. 3. Remove the antenna assembly and inspect the inner fender around the antenna hole for corrosion (Fig. 3). Clean with 1500 grit sandpaper.

Incoming search terms:

2003 – 2008 Corolla, Matrix Front Brake Rattle Noise REPAIR

0

Filed Under (Toyota Manuals) by admin on 13-10-2011

download
The information contained in this TSB supersedes TSB No. BR004-07. •The Titlehasbeenc hanged from”Front Brake Squeak”to”Front Brake Rattle Noise”. •Applicability has been updated to include 2008 model year Corolla and Matrix vehicles. •Production Change Information has been updated with new VIN information. •Parts Information has been updated. •The Components illustration (Figure 1) has been updated. •Step 1intheRepair Procedure has been modified. TSB No. BR004-07 is Obsolete and any printed versions should be discarded. Be sure tore view the entire content of this service bulletin before proceeding. Introduction Some customers ma yexperiencea front brake rattle type noise when the car is traveling over bumps. Updated front disc brake cylinder (caliper) mountings and disc brake pad support plates are available to eliminate this condition

Incoming search terms:

TOYOTA Steering Intermediate Shaft Knocking Noise

0

Filed Under (Toyota Manuals) by admin on 13-10-2011

download
Some 2009-2010 Corolla and Matrix vehicles ma yexhibitaclunk, pop, or knocking noise when turning the steering wheel to the left or right. Anew intermediate shaft has been developed to address this condition. Use the following repair procedure to remove and replace the steering intermediate shaft. Install a steering wheel lock to ensure the wheels are straight and the steering wheel is centered before removing the steering intermediate shaft. Make sure the steering wheel and front wheels remain stationary. Once the intermediate shaft is removed, do NOT allow the steering wheel to spin freely. 2. Remove the column hole silencer sheet

Incoming search terms:

AVALON WINDSHIELD MOLDING WIND NOISE REPAIR

0

Filed Under (Toyota Manuals) by admin on 01-11-2011

download
TOYOTA MOTOR SALES U.S.A., INC. TMM has implemented a production process change to improve windshield sealing. EFFECTIVE DATE VIN REFERENCE 4/26/95 4T1GB11E5SU038470 To eliminate whistling noise from the windshield top outside molding, fill in the windshield channel with a urethane sealant such as 3M Window Weld Re-sealant or equivalent (refer to illustration below for proper application)

TOYOTA Upper/ Lower Windshield/ Rear Glass Tick Noise

0

Filed Under (Toyota Manuals) by admin on 12-10-2011

download
Upper/Lower Windshield/Rear Glass Tick Noise Service Category Vehicle Exterior Section Window/Glass Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2003-2009 4Runner, Avalon, Camry, Camry HV, Celica, Corolla, Echo, FJ Cruiser, Highlander, Highlander HV, Land Cruiser, MR2 Spyder, Matrix, Prius, RAV4, RAV4 EV, Sequoia, Sienna, Solar a, Tacoma, Tundra, Venza, Yar is TSB REVISION NOTICE •July 13,2009 Rev2: •The Warranty Information table has been updated. •February2,2009 Rev1: •Applicability has been updated to include 2009 model years. •Titlehasbeen updated. •Introduction has been updated. •Warranty has been updated. Any previous printedversions of this service bulletin should be discarded. TSB SUPERSESSION NOTICE The information contained in this TSB supersedes TSB No. NV009-06. •Applicability has been updated to include 2008 model year applicable vehicles. TSB No. NV009-06 is Obsolete and any printed versions should be discarded. Be sure tore view the entire content of this service bulletin before proceeding

Toyota Noise from Auxiliary Port with External Device

0

Filed Under (Toyota Manuals) by admin on 09-10-2011

download
2006-2008 4Runner, Prius, RAV4 2007 Camry, Camry HV, FJ Cruiser, Yaris 2007-2008 Solara TSB SUPERSESSION NOTICE The information contained in this TSB supersedes TSB No. AU004-07. •Applicability has been updated to include 2008 model year 4Runner, Prius, RAV4, and Solara. •Parts Information has been updated to includea clarifying illustration. TSB No. AU004-07 is Obsolete and any printed versions should be discarded. Be sure tore view the entire content of this service bulletin before proceeding. Introduction Some customers may notice noise in the auxiliary mode of their audio system when using an MP3 player or other external audio source connected to the 12Vpowerportof the vehicle. An improved auxiliary port and in-line filter has been developed to improve this condition.Use the repair procedure below to install the new in-line filter and auxiliary port

2003 – 2005 Matrix WIND NOISE FROM DOOR GLASS WINDOW RUN REPAIR

0

Filed Under (Toyota Manuals) by admin on 28-10-2011

download
NOTE: Use the same procedure for the LH side as the RH side. 1. Place the window in the down position. 2. Remove the window run. Completely remove the double-sided tape remaining on the frame. 3. Thoroughly clean the door frame using a white body shop towel and Kent Acrysol. NOTE: Do NOT use red shop towels. These towels contain silicone. 4. Install the door glass window run. A. Position the glass run at the No. 2 and No. 3 corners of the door frame and then attach the middle part of the run. B. Insert the glass run into the window run channels. NOTE: Do NOT apply water or lubricant to the glass run when inserting it into the door. Make sure the glass run fits securely into the holes of the door frame

Incoming search terms:

1994 – 1996 Camry L4 A/C COMPRESSOR KNOCKING NOISE REPAIR

0

Filed Under (Toyota Manuals) by admin on 23-10-2011

download
Ensure that the A/C system high & low side refrigerant pressures are normal before Procedure proceeding with the following repair procedure. NOTE: For abnormal system pressures, use the diagnostic procedure given in the Repair Manual to determine the problem. 1. Remove the A/C Compressor. 2. Replace the Alternator Adjusting Bar with the new part number. 3. Replace the Magnetic Clutch Rotor with the new part number. 4. Adjust the clearance between the pressure plate and rotor from 0.35 to 0.60 mm (from 0.014 to 0.024 inch). NOTE: Use shims to adjust the clearance according to Repair Manual. 5. Install the A/C Compressor. 6. Adjust the drive belt tension to 121 ft. lbs. otherwise the condition may persist

2001 – '2005 Highlander (V6) FUEL INJECTOR TICKING NOISE

0

Filed Under (Toyota Manuals) by admin on 08-10-2011

download
Do NOT smoke or work near an open flame when working on the fuel system. Keep gasoline away from rubber or leather parts. Wear safety goggles while working with the fuel system under pressure. Do NOT disconnect any part of the fuel system until you have discharged the fuel system pressure. Even after discharging the fuel pressure, place a shop rag over fittings as you separate them to reduce risk of fuel spray on yourself or in the engine compartment. 1. Discharge fuel system pressure. A. Remove Circuit Opening Relay from Relay Block No. 1 located to the left of the Instrument Panel Junction Block behind the left lower finish panel If the connector and pipe are stuck, pinch the fuel pipe, push and pull the connector by hand to disconnect them. Do not use any tools. E. Drain the fuel that remains inside Fuel Pipe Sub-assembly No. 1. F. Place a tray under the vehicle or point of disconnection, if needed, to catch any fuel that may spill. G. Protect the disconnected fuel lines from debris by covering with a vinyl or plastic bag. H. Remove the original pulsation damper from the rear fuel rail. I. Remove and discard the remaining bolt holding Fuel Pipe Sub-assembly No. 1 to the front fuel rail

HARLEY DAVIDSON SCREAMIN' EAGLE STREET PERFORMANCE TOURING END CAP MUFFLER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 14-04-2011

download
PRODUCT INFORMATION Noise Emission Warranty Harley-Davidson warrants that these mufflers, at the time of sale, meet all applicable United States E.P.A. Federal noise and Emissions standards. This warranty extends to the first person who buys these mufflers for proposes other than resale, and to all subsequent buyers. Warranty claims should be directed to an authorized Harley-Davidson Dealer. Tampering Prohibition Federal law prohibits any modification to this exhaust system which causes the motorcycle to exceed the Federal noise standard. Use of the motorcycle with such a modified exhaust system is also prohibited. NOTE This product should be checked for repair or replacement if the motorcycle noise has increased significantly through use. Otherwise, the owner may become subject to penalties under state and local ordinances. INSTALLATION NOTE Install end caps on mufflers before installing mufflers on vehicle. Install Direct Bolt-On End Caps 1. See Figure 1. Install end cap (2) to muffler (3) with four socket head cap screws (1). Tighten to 82-86 in-lbs (9.3- 9.7 Nm) . 2. Repeat for opposite side muffler. 3 2 1 is05426 1. Socket head screw (4) 2. End cap 3. Muffler Figure 1. Install End Cap on Muffler Install Attachment Ring End Caps 1. See Figure 2. Slide the three U-nuts (2) onto the bosses of the end cap attachment ring cup on the muffler. 2. Install attachment ring (1) to muffler with four socket head cap screws (3). Locate the attachment ring with a U-nut in the 12 o’clock position. Tighten to 82-86 in-lbs (9.3-9.7 Nm) . 3. Slide end cap (5) onto muffler body being careful to align holes in end cap with U-nuts. 4. Install the three countersunk screws (4) and tighten screws securely. 5. Repeat for opposite side muffler

Incoming search terms:

Incoming search terms: