ss carb rebuild instructions

You search Auto repair manual PDF ss carb rebuild instructions, if there are search results will appear below. If search results do not exist, please search by others keyword.



  ss carb rebuild instructions Direct Download speed 5282 Kb/s

  ss carb rebuild instructions Full Version speed 6162 Kb/s



KAWASAKI 1500 CARB THUNDER Air Filter Kit Installation And removal Instruction

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Remove Seat 10mm KAW 1500 CARB ADPTOR QTY PARTS LIST 1 1500 CARB ADAPTOR 1 3″ PIECE OF HOSE 1 DOUBLE BARB 1 L-BARB 1 3/8″ RED PLUG 1 ¼” BLACK VACCUM PLUG 1 M6-1 NYLON INSERT LOCK NUT 3 M6-1 X 16 FLAT SOCKET HD CAP SCREW 1 170 MJ 1 INSTRUCTIONS 2) Remove Dash Plaque 8mm bottom Bolt only 3) Lift from bottom then Remove speedo cable 4) Disconnect Electric Plugs 5) Remove 12mm bolts holding tank 6) Turn petcock OFF – Pinch off fuel line. 7) Disconnect the electric Plug under speedo opening 8) Lift Tank at Rear – Disconnect two Vent Lines; Fuel gage Vent will Pull up – Remove. 9) Remove Chrome Air Cover. 10) Left side Remove two screws – 10mm bolt in side Air box. Pull hoses off Remove 1″ hose going to cross over Tube. 11) Remove two 8mm bolts on Bracket – Remove Bracket 12) Remove Screw on Top of air Box Snorkel 13) Remove both side covers 14) Remove air Backing plate right side (Crank Case Breather hose that connects to stock air box will connect to new) 15) Remove Bracket that holds Carb and holds Backing Plate 16) Take idle adjustable Knob loose – let hang loose 17) Take Choke Knob out of holding Bracket 18) Hose that went to cross over tube MAY BE PLUGGED OR VENTED your Choice (Fresh air unit) ** 98′S or any models with carb warmer should disconnect carb warmer by pinching off line on each side of connector that plugs into carb on bottom. Small bracket with one screw directly on the bottom of carb. 19) Loosen Clamp that holds Carb to intake Manifold, Carb will hang loose 20) Remove intake Manifold 5mm Allen- Remove crossover tube. 21) (- BE CAREFULL-) LINE IT UP RIGHT- Replace intake Manifold (YOU MAY TO SEAL THIS WITH A SEALER LIKE PERMATEX) ( BE SUPER CAREFUL TO KEEP INTAKE COVERED DURING EACH STEP. SCREWS CAN FALL ONTO INTAKE) 22) Drain Float Bowl 3mm allen – very bottom of carb 23) Remove Float Bowl 4 screws (#2 Phillips) let hang down 24) Remove main jet, if Emulsion tube comes out use 8mm and Flat tip to separate jet from Emulsion tube. 25) Install with new jet 26) CAREFULLY Reinstall Float Bowl Cover 27) If installing Needle Remove Top Cover of Carb, Carefully pull the slide out. ( BE CAREFUL WITH DIAPHRAM) Remove Spring + Needle Install new Needle (WE RECOMMEND THE 3RD CLIP FROM TOP WITH TWO WASHERS ON TOP. REINSTALL 28) Be sure to reseat diaphragm – BE CAREFUL Reinstall Cover. 29) Install Carb to Intake – reconnect carb warmer if applicable 30) Reattach idle adjustment 31) Reattach Choke 32) Reattach Bracket in front of Carb- 33) Take Center bolt mount Rubber Gromlet from Stock Air box Plate install in to new Air box Adapter use stock Bolt, Attach to Bracke

Incoming search terms:

HW Prowler Carburetor Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
1. Remove both seats and the plastic seat pans under the seats. 2. Remove the engine cover 3. Remove the air-box by removing the cross-bar support that runs under the air-box to the framing on each side by the seat framing and disconnect the air box from the carburetor and from the plastic intake in the rear. 4. Disconnect the engine breather hose from the bottom of the air box 5. Set the air-box to the side 6. Disconnect the plug going to the stock carburetor, this is the electronic choke. Wrap the end left on the vehicle with electrical tape. 7. Cut the fuel line just above the fitting on the passenger side of the carb 8. Remove the side cover off the drivers side of the carb where the throttle cable goes in, see fig. #1 9. Pull the throttle cable out and then remove the throttle cable end from the throttle plate See Fig. #2 10. Loosen the clamp on the rear of the carb holding the carb on 11. Pull the carb out of the intake boot 12. Set OE carb to the side. 13. Push the new Carb into the intake boot making sure the carb is perfectly vertical and then tighten the clamp back up. The new carb is slightly larger than the stock one so some additional pressure will be needed to get it in. 14. Route all the breather lines connected to the carb down under the carb. 15. Connect the throttle cable onto the new carb but putting the cable end in the bottom hole of the throttle plate on the passenger side of the carb allowing the cable to ride in the slot in the plate and then turn the throttle plate clock wise allowing the threaded end of the cable to fit into the lower round hole of the throttle cable connection plate. See Fig. #3 16. Make sure you have a nut on each side of the plate turn the nut on the outside of the plate to take up the slack in the throttle cable then tighten the nut on the inside of the plate. See Fig. #3 17. Push the fuel line onto the fuel inlet on the passenger side of the carb and install the supplied clamp to hold it on. The fuel line will be a little hard to push on. 18. DO NOT ATTEMPT TO INSTALL THE CHOKE CABLE PARTS SUPPLIED IN THE KIT UNTIL AFTER THE CHOKE CABLE ITSELF IS INSTALLED AND READY TO SCREW INTO THE CARBUETOR. 19. To install the supplied choke cable, drill a 3/8″ hole in the dash on the left side of the steering wheel in a location convenient to your left hand. 20. Remove the plastic nut from the bottom of the choke handle on the choke cable. 21. Push the choke cable thru the hole you drilled and then slide the nut over the cable to the inside of the dash and reinstall back on the back of the choke mechanism. Some dash screws maybe needed to be removed to accomplish this

Incoming search terms:

42MM MIKUNI FLATSLIDE CARBURETOR INSTRUCTIONS

0

Filed Under (Mikuni) by admin on 31-10-2010

download
To install, remove the stock carb per Yamaha shop manual procedures. Remove stock throttle cables. Install Mikuni HSR carb into intake manifold and tighten manifold clamp. Install new HSR series throttle cables and adjust cable slack per Yamaha shop manual procedures. Hook fuel line to HSR carb and fasten clamp.* Start motorcycle and fine tune HSR carb for proper running per supplied Mikuni tuning manual. *NOTE: Mikuni HSR series carburetors are designed for gravity-feed fuel systems. You should bypass your stock fuel pump and directly feed your HSR carb right from the fuel petcock. We have noted, though, that you may not be able to get good fuel flow from your Road Star fuel tank in low-fuel situations. You may run your stock fuel pump with the HSR carb, but to do so requires the purchase and installation of an adjustable fuel pressure regulator (set at 1/2 to 1 lb. of pressure). These are available from most auto parts stores. The stock carb has 2 wires running to the lower rear of the float bowl , these were for a carb warmer, they are not used in this application. Unplug these wires at the main wire harness and retain with your stock carb. The Road Star ignition system uses data from the stock throttle position sensor (TPS) to manage your ignition timing. It is necessary to give the bike this information. You may do so by removing the TPS sensor from the stock carb, leaving it plugged into the main wire harness (the sensor must be fixed to a closed-throttle position), or you may locate the plug for the TPS on the main wire harness and test the leads – you will find one ground, one with .5V and one with 1.5V. Connect the 1.5V to the ground and this will give the bike the same information as stock fully closed throttle. The output of the OEM fuel pump is too high and will cause fuel overflow in the HSR carb, resulting in a possible dangerous fire hazard

Incoming search terms:

Mikuni HSR 42/ 45 Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
To install, remove the stock carb per Yamaha shop manual procedures. Remove stock throttle cables. Install Mikuni HSR carb into intake manifold and tighten manifold clamp. Install new HSR series throttle cables and adjust cable slack per Yamaha shop manual procedures. Hook fuel line to HSR carb and fasten clamp.* Start motorcycle and fine tune HSR carb for proper running per supplied Mikuni tuning manual. *NOTE: Mikuni HSR series carburetors are designed for gravity-feed fuel systems. You should bypass your stock fuel pump and directly feed your HSR carb right from the fuel petcock. We have noted, though, that you may not be able to get good fuel flow from your Road Star fuel tank in low-fuel situations. You may run your stock fuel pump with the HSR carb, but to do so requires the purchase and installation of an adjustable fuel pressure regulator (set at ½ to 1 lb. of pressure). These are available from most auto parts stores. The stock carb has 2 wires running to the lower rear of the float bowl , these were for a carb warmer, they are not used in this application. Unplug these wires at the main wire harness and retain with your stock carb. The Road Star ignition system uses data from the stock throttle position sensor (TPS) to manage your ignition timing. It is necessary to give the bike this information. You may do so by removing the TPS sensor from the stock carb, leaving it plugged into the main wire harness (the sensor must be fixed to a closed-throttle position), or you may locate the plug for the TPS on the main wire harness and test the leads – you will find one ground, one with .5V and one with 1.5V. Connect the 1.5V to the ground and this will give the bike the same information as stock fully closed throttle.

HARLEY DAVIDSON SECURITY SYSTEM SMART SIREN KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
REMOVAL 1. Refer to the owner’s manual and follow the instructions to disarm the security system. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. For All Models except 2002-2003 Touring and 2003- Later Softail: Refer to the owner’s manual and follow the instructions to disconnect the battery, negative (-) cable first or remove the main fuse. For 2002-2003 Touring and 2003-Later Softail Models: Remove seat following the instructions in the service manual and disconnect the battery, negative (-) cable first. Save seat hardware for installation. INSTALLATION 2002-2006 VRSCA, VRSCB, VRSCD Models 1. Open the seat. 2. See Figure 1. Remove the splash guard (mud flap) nuts. 3. See Figure 2. Lower the mud flap from the installed position and allow it to rest on the rear tire 3. Slide the siren into place on the left side of the electrical caddy so the sounder disc (6) faces out. 4. Refer to the owner’s manual and follow the instructions to install the main fuse. 5. Align the barbed studs on the side cover with the grommets in the frame and push side cover firmly into place. 6. Install the left side saddlebag per the instructions in the owner’s manual. 2003 and later Softail Models EXCEPT FXCW/C 1. Remove the right side saddlebag (if equipped) per the instructions in the owner’s manual. NOTE The siren connector is installed on an electrical panel under the rear fender on all Softail models. The rear of the motorcycle may have to be raised slightly to allow removal of the splash guard. 2. Remove the two bolts at the bottom of the splash guard. Bend the upper right corner of the splash guard toward the rear tire and lift upward to unhook the splash guard from the tab on the rear fork. Remove the guard from beneath the fender. 2 1 3 is01316 1. Siren mounting area 2. Siren connector [142B] 3. Harness clip Figure 16. Siren Connector (Softail Models EXCEPT FXCW/C) (Rear Fender View with Rear Wheel Removed) 3. See Figure 16. Remove the siren connector [142B] (2) from the receptacle in the siren mounting area (1) of the electrical panel. 4. See Figure 17. Insert security siren (1) connector [142B] into the siren box receptacle until the connector latches securely. 5. Orient the siren (1) as shown, with the harness connector (2) toward the bottom and the sounder disc (5) facing out. Carefully snap the siren into the electrical panel. 6. Insert the siren harness lead (4) into the harness clip (3) to keep the harness clear of other components. 7. If necessary, secure the connector wiring to the electrical panel wiring with a cable strap (not provided). 8. Hook the slot at the top of the splash guard over the tab on the rear fork and install the guard with the two screws removed earlier. Tighten securely. 9. Install the right side saddlebag (if equipped) per the instructions in the owner’s manual. 10. Refer to the owner’s manual and follow the instructions given to connect the battery cables or install the main fuse

Incoming search terms:

HARLEY DAVIDSON MINI-TACH WITH SHIFT LIGHT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
INSTALLATION Preparation For EFI models: To prevent spray of fuel, purge system of high-pressure fuel before supply line is disconnected. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00275a) Follow the instructions found in the Service Manual to purge the fuel supply of high pressure gasoline and remove the fuel supply line. For ALL models, WITH Maxi-Fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the Maxi-Fuse. For ALL models, WITHOUT Maxi-Fuse: To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (black) battery cable from the negative (-) battery terminal. Retain all seat mounting hardware. -J04106 Gasoline can drain fr om the carb uretor fuel line when disconnected from fuel valve fitting. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. Wipe up spilled fuel immediately and dispose of rags in a suitable manner. (00256a) 2. For carbureted models: Turn the fuel supply valve to OFF. Remove the fuel line from the valve. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 3. For ALL models: Follow the instructions in the Service Manual to remove the instrument console from the fuel tank. 4. See FUEL TANK: REMOVAL in the appropriate section (Carbureted or EFI Engine) of the Service Manual for instructions to remove the tank. 5. For all models EXCEPT FLHR or 1986 and later FL Softail models with Chrome Headlight Nacelle Kit (Part Number 67907-96): Follow the instructions in the Service Manual to remove the headlamp housing. For FLHR models, or Softail models WITH the Nacelle Kit: Follow the instructions in the Service Manual and the mini-tach bracket kit (purchased separately) to remove the handlebar shroud. Mini-Tach Bracket Installation 6. For all models except FLHR: Install the mini-tach bracket components per the instructions in that kit. For FLHR models: Follow the instructions in the Service Manual and the mini-tach bracket kit to install the handlebar shroud and bracket components. 7. See Figure 7. Select the rubber isolation gasket (1) from this kit.

Incoming search terms:

HARLEY DAVIDSON CHROME FORK SLIDERS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 10-02-2011

download
REMOVAL 1. Support the motorcycle so the front end is off the floor and the forks are fully extended. 2. Remove the front fender, front brake caliper(s) and front wheel according to instructions found in the Chassis section of the appropriate service manual. NOTE On some models other parts will also need to be removed to access the front forks. See the service manual. 3. For All Models EXCEPT Touring: Drain and remove the front forks. See the service manual. 4. For Touring models equipped with air-adjustable suspension: Bleed the air-adjustable suspension according to the instructions in the appropriate service manual. Wear safety glasses or goggles when servicing fork assembly. Do not remove slider tube caps without relieving spring preload or caps and springs can fly out, which could result in death or serious injury. (00297a) 5. For 2000 and Later Models EXCEPT Touring: See Figure 1. Using a piece of dental floss (or similar material) in a back and forth motion, loosen reflector from fork slider at both ends. Rotate reflector from side-to-side until it can be removed. Save reflector for future use. See Figure 2. Repeat procedure on the opposite side fork slider. Peel off any excess adhesive from both reflectors . Surface must be clean for installation. 6. Disassemble the front fork tubes according to instructions in the service manual. INSTALLATION NOTES The chrome fork sliders included in this kit install in the same manner as the original equipment parts. Refer to the service manual for proper installation procedures. Prior to installation of this kit, check the bores of the new chrome sliders to be certain they are free of dirt and debris or damage to the new sliders may occur. 1. Assemble the front fork tubes, replacing worn seals, bushings or other items as needed. NOTE Do not use an impact wrench to tighten the drain screws. Use of an impact wrench may damage the screws. 2. Tighten the drain screws: •Early Models with 39 mm forks (see Figure 2): Tighten to 13-17 in-lbs (1.5-1.9 Nm) •Early Models with 41 mm forks (see Figure 2): Tighten to 52-78 in-lbs (5.8-8.8 Nm) •Later Models (see Figure 3): Tighten to 52-78 in-lbs (5.8- 8.8 Nm) 3. Fill with TYPE E FORK OIL (99884-80) according to the instructions in the service manual. 4. Install the front fork and any parts that were removed to access the front forks. Install the front fender, wheel and caliper(s) according to instructions in the service manual. 5. For Touring models equipped with air-adjustable suspension: Refill the air-adjustable suspension system after assembly according to the service manual instruc- tions

Incoming search terms:

HARLEY DAVIDSON CENTER-MOUNTED LICENSE PLATE BRACKET KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions given to remove the seat and disconnect the negative (-) battery cable. Retain all seat mounting hardware. 2. Remove rear fender and side-mounted license plate bracket following the instructions in the Service Manual. INSTALLATION 1. Assemble and install the rear fender and the center- mounted license plate bracket following the instructions in the Service Manual. 2. Connect the license plate lamp connector following the instructions in the Service Manual. After installing seat, pull upward on seat to be sure it is locked in position. While riding, a loose seat can shift causing loss of control, which could result in death or serious injury. (00070b) 3. Install the seat and connect the negative (-) battery cable following the instructions in the Service Manual.

HARLEY DAVIDSON ROAD ZEPPELIN SEAT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Remove main fuse following the instructions in the service manual. NOTE Cover the painted surfaces with protective material to prevent scratches or other damage. 2. Remove the left and right side saddlebags following the instructions in the owner’s manual. 3. See Figure 1. Remove the screw (1) and lockwashers (2) securing the grab strap (3) to the bracket (4 or 6). Save the hardware for installation. 4. Remove the grab strap. 5. Remove seat following the instructions in the service manual. -J04456 1 of 4 1 2 4 3 1 2 6 3 5 7 is06068 1. Stock screw 2. Stock lockwasher 3. Grab Strap 4. Bracket, 2009-Later Models 5.2009-Later Models 6. Bracket, 2008-Earlier Models 7.2008-Earlier Models Figure 1. Grab Strap and Saddlebag Front Mounting Bracket INSTALLATION 1. See Figure 2. Remove rubber plug from accessory connector (1) located under seat. Plug the seat electrical connector into the accessory connector. The connectors should lock together with an audible click. 2. Position the seat on the frame. Make sure the electrical harness and connector are not pinched between the seat and frame. 3. Install the seat following the instructions in the service manual.

Baron Tachometer Installation Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Some models like Harley-Davidson, Kawasaki Vulcan FI models, Suzuki FI models, Honda VTX 1800 and others may require the included Tach Adapter. See separate instructions for installation of the adaptor. Wiring instructions for 7-Color LED Tachs Wire Baron’s Tach to one of your motorcycle’s ignition coils via the following schematic: • Green wire of tach to NEGATIVE terminal of coil (see FAQ to determine your bike’s negative side) • Black wire of tach to CHASSIS (Ground) • Red wire to of tach to POSITIVE terminal of coil (or other switched 12 volt source) • Red wire from control box to POSITIVE terminal of coil (or other switched 12 volt source) • Black wire from control box to CHASSIS (ground) • Control box plugs into tach with the 4-way connector • Button plugs into the control box. Button can be mounted on handlebar or any other convenient place Wiring instructions for White- or Black-Face Tachs Wire Baron’s Tach to one of your motorcycle’s ignition coils via the following schematic: • Green wire to NEGATIVE terminal of coil (see FAQ to determine your bike’s negative side) • Black wire to CHASSIS (Ground) • Red wire to POSITIVE terminal of coil (or other switched 12 volt source) • Blue wire to POSITIVE terminal of coil (or other switched 12 volt source) General mounting instructions (1) Mount new Baron Tach on handlebar in your preferred position. Ideal location is between handlebar risers. If mounted off- center, you can rotate tach face back to vertical (or any position you desire) by first loosening tach unit’s set screw (found either in handlebar area of housing or underside of housing, depending on tach style), then unscrewing tach housing’s bezel, rotating tach, re-installing bezel and retightening set screw. Secure handlebar clamp by first tightening the rear, flat side of clamp all the way down, then tighten tapered front side of clamp until tach does not rotate. There should be a small gap on the pointed side and no gap on the flat side when the clamp is correctly tightened. (2) Route tach’s wire harness lead to coil as necessary for simplest and cleanest installation. Feed tach harness alongside bike’s wiring harness (passing behind any plastic frame covers), then downward toward coil. (3) Make your wire connections as recommended above. Use the spade and piggyback connectors

Incoming search terms:

Incoming search terms: