st1300 bulb change

You search Auto repair manual PDF st1300 bulb change, if there are search results will appear below. If search results do not exist, please search by others keyword.



  st1300 bulb change Direct Download speed 5282 Kb/s

  st1300 bulb change Full Version speed 6162 Kb/s



YAMAHA V-MAX PERIODIC MAINTENANCE AND MINOR REPAIR

0

Filed Under (Yamaha) by admin on 25-11-2010

download
PERIODIC MAINTENANCE AND MINOR REPAIR -. 1. Screw (x 2) EAU03003 Replacing the headlight bulb This motorcycle is equipped with a quartz bulb headlight. If the headlight bulb burns out, replace it as follows. 1. Remove the headlight unit by re- moving the screws. 2. Disconnect the headlight coupler, and then remove the headlight unit and bulb cover. 1. Headlight bulb holder 3. Remove the headlight bulb holder by turning it counterclockwise, and then remove the defective bulb. EWOOOl19 Headlight bulbs get very hot. Therefore, keep flammable products away from a lit headlight bulb, and do not touch the bulb until it has cooled down. 4. Place a new bulb into position, and then secure it with the bulb holder. 1. Do not touch this area. EC000105 Do not touch the glass part of the headlight bulb to keep it free from oil, otherwise the transparency of the glass, the luminosity of the bulb, and the bulb life will be adversely affected. Thoroughly clean off any dirt and fingerprints on the headlight bulb using a cloth moistened with alcohol or thinner. 5. Install the bulb cover, and then connect the coupler. 6. Install the headlight unit by install- ing the screws. 7. Have a Yamaha dealer adjust the headlight beam if necessary. 6-40 PERIODIC MAINTENANCE AND MINOR REPAIR 1. Screw (x 2) 1. Tail/brake light bulb (x 2) EAU00855 Replacing a turn signal light bulb or the tail/brake light bulb 3. Insert a new bulb into the socket, push it in, and then turn it clock- wise until it stops. 1. Remove the lens by removing the screws. 2. Remove the defective bulb by pushing it in and turning it counter- clockwise. 1. Turn signal light bulb 4. Install the lens by installing the screws. EC000108 Do not overtighten the screws, oth- erwise the lens may break

Incoming search terms:

1999 Toyota Camry LE V6 Body and Interior Maintenance Record

0

Filed Under (Toyota Manuals) by admin on 03-10-2011

download
Action Date Mileage Day Cost (with tax) By Interval Notes Oil and Oil Filter Change 8/30/1999 2494 Monday$77.97 Dealer 2494Non-synthetic 5w-30 (Toyota dealer stock) Oil and Oil Filter Change 10/31/1999 5484 Sunday $30 Owner 2988.5Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 12/30/1999 8460 Thursday$30 Owner 2975.9Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 2/21/2000 11414 Monday $30 Owner 2953.3Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 4/22/2000 14479 Saturday$30 Owner 3065.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 7/4/2000 17339 Tuesday$30 Owner 2860.1Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Air Filter – Replace 7/4/2000 17339 Tuesday$15 Owner 17339Purolator A24690 Air Filter Oil and Oil Filter Change 9/16/2000 20161 Saturday$30 Owner 2821.9Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Transmission Drain and Fill 10/27/2000 21913 Saturday$15 Owner 21913Drain and Fill 2.5 Quarts Mobil 1 Dexron III Synthetic ATF Transmission Drain and Fill 10/28/2000 21920 Sunday $15 Owner 7Drain and Fill 2.5 Quarts Mobil 1 Dexron III Synthetic ATF Oil and Oil Filter Change 11/19/2000 23066 Sunday $30 Owner 2904.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 2/11/2001 26062 Sunday $30 Owner 2996.1Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Transmission Flush 4/30/2001 28351 Monday$135 Dealer 2835113 Quarts Mobil 1 Dexron III Synthetic ATF – TransTech Flush Tires – Rotate 5/12/2001 28766 Saturday$0 Dealer 28766Tires – Rotate Coolant Flush 5/12/2001 28766 Saturday$112 Dealer 28766Toyota Red Coolant + MOC Flush (Extended warranty with service) Oil and Oil Filter Change 5/13/2001 28793 Sunday $30 Owner 2730.6Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Air Filter – Replace 5/13/2001 28793 Sunday $15 Owner 11454Purolator A24690 Air Filter PCV Valve – Replace 5/26/2001 31083 Saturday$10 Owner 31083Toyota OEM PCV Valve Windshield Wipers – Replace 5/26/2001 31083 Saturday$10 Owner 31083Windshield Wipers – Replace Oil and Oil Filter Change 5/27/2001 31296 Monday $30 Owner 2502.8Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Oil and Oil Filter Change 9/15/2001 34374 Saturday$30 Owner 3078.5Mobil 1 5w-30 + Mobil 1 Filter (M1-102) Tires – Replace 9/28/2001 34784 Friday$431.23 Dealer 34784 (4) Bridgestone RE950 Tires (2 of original tires had tread separation – ~30% tread remaining) Oil and Oil Filter Change 11/12/2001 37365 Monday $30 Owner

Incoming search terms:

2008-2009 KAWASAKI TERYX HEADLAMPS HIDTERYX HID KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
a. Remove rubber boot from the back of the headlamp housing assembly. b. Push down on metal latch and pull away from lip to release halogen bulb. Pull out halogen bulb. c. Insert HID bulb, line up bulb to fit into the bulb holder, lower latch to lock bulb in place. d. Replace Rubber boot on the back headlamp assembly. (Make sure to pull wires through the center of the rubber boot first before you start to pull down boot on the back of the headlamp assembly.) e. Make sure that the wiring, coming from the HID bulb, clears the black plastic housing that encases the headlamp assembly so connection from the bulb to the ballast is possible. If installed correctly there is no need for drilling or modifications of any type. 2. Ballast a. Mount ballast in location of your choice – recommended near the headlight. 3. Wiring Note: DO NOT modify the wiring that runs from the HID bulb to the ballast. It will cause the system to work improperly. It will void the warranty . a. Once ballast is installed connect corresponding wires from HID bulb to corresponding male / female plugs on ballast. b. To connect wiring from ballast to Teryx primary system i. Find wire extension with white triangular head with black, yellow & green wires at opposite end ii. Connect black off extension to black wire coming off ballast iii. Connect Yellow / Green wire to red wire coming off ballast iv. Connect triangular head to corresponding plug on Teryx Factory Wiring End

Incoming search terms:

MACHINE SPECIFICATION FOR 115cc (UNDERBONE) (4-stroke horizontal layout engine)

0

Filed Under (Tips and Review) by admin on 12-12-2010

download
(This is for clarification only. Other parts not listed in Art. 2.5 & 2.6 can be altered or replaced. Change of specification means modification, changes or removal of the parts.) 2.6.1 Change of compression ratio is allowed. 2.6.2 Setting of carburetor, attachment or size change of air funnel. 2.6.3 Inlet opening of fuel tank for fuel charge may be modified but cannot be relocated. 2.6.4 Change of fuel pipe and fuel cork. 2.6.5 Change of exhaust pipe and muffler, but must have silencer. 2.6.6 Material of clutch discs and specifications of spring. Hand clutch is allowed. 2.6.7 Gear ratios are free. 2.6.8 Starting device and parts relative to this device may be removed. 2.6.9 Modification or removal of air cleaner box, wire harness and control wires. 2.6.10 Removal of speedometer (including meter gearbox and cable.) 2.6.11 Removal of drive chain case and cover. Change of drive chain is allowed. 2.6.12 Change of final gear ratio is allowed. 2.6.13 Attachment of bead stopper and balance weight to tyre. 2.6.14 Modification and change of rear brake part is allowed. 2.6.15 Frame body may be strengthened. 2.6.16 Modification and change to brackets and pedals including footrest. 2.6.17 Front suspension unit must remain as originally produced by the manufacturer. However, the following internal parts of the fork can be modified: Shims, hydraulic piston, oil passages, springs and spacers. 2.6.18 Attachment of stabilizer to strengthen or reinforcing rear swing arm is allowed. 2.6.19 Removal of dust seals. 2.6.20 Rear suspension unit must remain as originally produced by the manufacturer. However rear suspension unit is free. The rear linkage must remain as originally produced by the manufacturer. 2.6.21 Handle bars, clutch and front brake lever may be changed by an after market copy. Clutch springs may be changed. 2.6.22 Steering dampers may be fitted. They must not act in any way as a steering lock limiting device. 2.6.23 Materials of streamlining and material of seat cowling. (However, expensive materials such as carbon fibre and kevlar are not allowed). 2.6.24 Removal of rear mudguard and side cover. Front mudguard may be cut but not less than 6 inches from the front fork on original part. 2.6.25 All lubricants are free 2.6.26 Adjusting and polishing any parts are allowed. Adjusting is defined as : “To select each part or assembly complete with-in the limit of single or total tolerance” (i.e. that of valve clearance, ignition timing etc.) 2.6.27 Cutting unnecessary stays is

Incoming search terms:

2006 Honda ST1300/ A SET-UP INSTRUCTIONS

0

Filed Under (Honda) by admin on 21-04-2011

download
Remove the carton cover. The ST1300/A is crated in one of two ways. You may receive either one. Covered crate: Cut the strap and remove the carton cover. Remove the inner cardboard frame cover. Uncovered crate: When stacking crates, protect the motorcycle from falling objects and bad weather. 2. Check for damage. Check the unit for hidden damage. If you find damage, follow the instructions on the Delivery and Damage Claims Guidelines wall chart (Reorder No. S0477) before proceeding. 3. Remove the side braces, wheel, loose parts cartons, and crate frame. Remove the ties securing the front wheel and loose parts cartons. 3. Remove the side braces, wheel, loose parts cartons, and crate frame (cont.). Remove the bolts and side braces, being careful not to damage the front wheel. Remove the loose parts cartons. Keep the You and Your Motorcycle Riding Tips & Practice Guide and hand deliver to the customer at the time of delivery. Remove the nuts, plate, and bolts. Using two people, carefully remove the crate frame, being careful not to damage the motorcycle Remove the motorcycle from the crate base. Install lifting slings on the engine guards and grab rails as shown. If necessary, use a spreader board to prevent the slings from damaging the motorcycle. Lift the slings just enough to remove the slack. Loosen the caliper bolts, axle bolt, and axle pinch bolts. Remove the washer bolts, and lower shipping bracket from the crate base. Discard the washer bolts

2003 Honda ST1300/A Wire Harness Inspection and Repair Manual

0

Filed Under (Honda) by admin on 21-04-2011

download
REPAIR PROCEDURE Note: While completing this procedure DO NOT disconnect the 2-pin connector unless repair of the wire harness is required. 1. If not previously done, complete the ST1300/A #1 Service Bulletin before starting this procedure. 2. Remove the seats, left saddlebag, and left side panel by following the instructions in section 2 of the Service /l/Ianua/on pages 2-5 and 2-6. 3. Secure the centerstand assist handle out of the way. 4. Remove the rear shock adjuster support bar top bolt and move the bar out of the way. 5. Locate the ignition cord leading to the 2P connector and check the two black and white wires for chafing. |GNlTl6N con BLACK AND WHITE WIRES Chafing V I may OOCUF _ in this area 2-PIN CONNECTOR 2of6 – If the insulation is still intact and copper wire is not showing, proceed to the Preventative Measure section of this bulletin. – lf copper wire is showig, wrap the exposed area of the wire with a good quality electrical tape and proceed to the Preventative Mea- sure section of this bulletin. Preventative Measure: 1. Place the length of PVC split tubing around the ignition cord, butting up against the con- nector. Rotate the split toward the inside of the motorcycle. 2. Use good quality electrical tape to cinch the end of the PVC split tubing together (at the end that is touching the 2-pin connector), together. Secure the PVC split tubing to the ignition cord at the other end with electrical tape. 3. Secure the ignition cord and wire harness cord to the rear sub-frame with a commer- cially available wire band. The 2-pin connector should be routed behind and to the rear of where the rear shock adjuster support bar is located. ~! IR ARNESS C R COR W EH O D

Incoming search terms:

HARLEY DAVIDSON HIGH INTENSITY DISCHARGE (HID) DUAL BULB HEADLAMP KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 04-04-2011

download
REMOVAL 1. Remove seat according to the instructions in the service manual. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. 2003-Earlier Models: Disconnect battery cables, negative (-) cable first. Refer to the service manual. To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 3. 2004-Later Models: a. Remove left saddlebag. Refer to the service manual. b. Remove left side cover and main fuse. Refer to the service manual. 4. Remove fuel tank according to the instructions in the service manual. 5. See Figure 1. Remove the Phillips screw (1) at the bottom of the bezel and remove the bezel. Save parts for installa- tion. 1 2 is03916 1. Phillips screw 2. Bezel Figure 1. Remove Bezel 6. See Figure 2. Remove and save Phillips screws (1) that secure mounting ring assembly (2) to nacelle. 7. Gently pull headlamp assembly out far enough to disconnect wiring. Save short wire harness for installation. 8. Remove wire connector at the back of the headlamp bulb. 9. See Figure 2. Remove three screws (3) securing the retaining ring (4) and headlamp assembly to mounting ring assembly. Discard mounting ring assembly, but save three screws and retaining ring for installation

YAMAHA FJR1300N PERIODIC MAINTENANCE AND MINOR REPAIR

0

Filed Under (Yamaha) by admin on 17-12-2010

download
Always keep the battery charged. Storing a discharged battery can cause permanent battery damage. ● To charge a sealed-type (MF) battery, a special (constant- voltage) battery charger is required. Using a conventional battery charger will damage the battery. If you do not have access to a sealed-type (MF) battery charger, have a Yamaha dealer charge your battery. EAU04076* Replacing the fuses The fuse box, which contains the fuses for the individual circuits, is located under panel D. The fuel injection system fuse box is located under panel D. The main fuse box is also located under panel D, beside the battery. (See page 6-7 for panel removal and installation procedures.) If a fuse is blown, replace it as follows. 1. Turn the key to “OFF” and turn off the electrical circuit in question. 2. Remove the blown fuse, and then install a new fuse of the specified amperage. 1. Fuel injection system fuse 2. Spare fuel injection system fuse 1. Headlight fuse 2. Signaling system fuse 3. Ignition fuse 4. Windshield motor fuse 5. Radiator fan fuse 6. Backup fuse (odometer and clock) 7. Spare fuse (〈 4)
PERIODIC MAINTENANCE AND MINOR REPAIR 6-31 6 EC000103 CAUTION: Do not use a fuse of a higher amperage rating than recommended to avoid causing extensive damage to the electrical system and possibly a fire. 3. Turn the key to “ON” and turn on the electrical circuit in question to check if the device operates. 4. If the fuse immediately blows again, have a Yamaha dealer check the electrical system. EAU04099 Replacing a headlight bulb This motorcycle is equipped with quartz bulb headlights. If a headlight bulb burns out, replace it as follows. 1. Remove panel B (if replacing the left headlight bulb) or panel C (if replacing the right headlight bulb). (See page 6-7 for panel removal and installation procedures.) 2. Disconnect the headlight coupler, and then remove the headlight bulb cove

Incoming search terms:

HARLEY DAVIDSON VRSC TURN SIGNAL RELOCATION KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 08-03-2011

download
INSTALLATION Removing Turn Signals To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Remove the 40 amp Maxi-Fuse or disconnect the battery cables, negative cable first. Never touch the quartz bulb. Fingerprints will etch the glass and decrease bulb life. Grab the bulb with paper or a clean, dry cloth. Failure to do so could result in bulb damage. (00210a) 2. For VRSCA models, remove headlamp assembly. For VRSCB models, continue to Step 4. a. While facing the headlamp from behind (looking toward front of motorcycle), reach behind the headlamp bucket and twist the headlamp bulb approximately 45 degrees counterclockwise, then gently pull straight out of the headlamp. Repeat for remaining bulb. Temporarily secure bulbs out of the way for the following steps. b. See Figure 1. Remove the two mounting screws securing the headlamp bracket to the upper triple clamp and remove headlamp assembly. Save hard- ware

2007 Harley-Davidson CVO Family: Specifications

0

Filed Under (Harley Davidson) by admin on 02-11-2010

download
1. Harley-Davidson reserves the right to discontinue models or change specifications at any time without incurring any obligations. Vehicle specifications may vary by country and region depending on local laws. Some models are not available i certain countries. 1. Harley-Davidson reserves the right to discontinue models or change specifications at any time without incurring any obligations. Vehicle specifications may vary by country and region depending on local laws. Some models are not available in certain countries. 1. Harley-Davidson reserves the right to discontinue models or change specifications at any time without incurring any obligations. Vehicle specifications may vary by country and region depending on local laws. Some models are not available in certain countries. 2. Measurement reflects 81.7 kg operator weight. 2. Measurement reflects 81.7 kg operator weight. 2. Measurement reflects 81.7 kg operator weight. 3. Recommended 91 octane or higher fuel (R+M)/2 (87 octane or higher for XL 883 models). Standard and optional fuel systems may vary by country and region. 3. Recommended 91 octane or higher fuel (R+M)/2 (87 octane or higher for XL 883 models). Standard and optional fuel systems may vary by country and region. 3. Recommended 91 octane or higher fuel (R+M)/2 (87 octane or higher for XL 883 models). Standard and optional fuel systems may vary by country and region. 4. Standard and optional wheels may vary by country and region. 4. Standard and optional wheels may vary by country and region. 4. Standard and optional wheels may vary by country and region. 5. Values shown are nominal. Performance may vary by country and region. 5. Values shown are nominal. Performance may vary by country and region. 5. Values shown are nominal. Performance may vary by country and region. 6. Security systems include the immobiliser and siren. 6. Security systems include the immobiliser and siren. 6. Security systems include the immobiliser and siren. 7. Availability of colours may vary from dealer to dealer and is subject to change without notice. 7. Availability of colours may vary from dealer to dealer and is subject to change without notice. 7. Availability of colours may vary from dealer to dealer and is subject to change without notice. 8. Model not available in all markets. 8. Model not available in all markets. 8. Model not available in all markets. 9. See motorcycle owner’s manual for complete details. 9. See motorcycle owner’s manual for complete details. 9. See motorcycle owner’s manual for complete details. 10. Inspections of certain systems and components are required at 4,000 km intervals. 10. Inspections of certain systems and components are required at 4,000 km intervals. 10. Inspections of certain systems and components are required at 4,000 km intervals.

Incoming search terms:

Incoming search terms: