stainless steel trimming factory singapore

You search Auto repair manual PDF stainless steel trimming factory singapore, if there are search results will appear below. If search results do not exist, please search by others keyword.





Harley- Davidson Bagger Audio factory service manual for removal

0

Filed Under (Harley Davidson) by admin on 03-04-2012

download
POWER & SPEAKER HARNESS INSTALLATION- (Read electrical connections prior to connecting center power and ground wires) 1. Disconnect battery (negative cable first!) 2. Remove outer faring cover 3. Route long speaker wires from fairing area through tank channel to seat area. 4. Route one pair of speaker wires under each fender strut support; purple and purple and black wires to the right and green and green and black wires to the left. AMPLIFIER INSTALLATION- 1. Factory installed electronics will determine suggested placement of amplifier. 2. Position and attach amplifier to outer fairing support bars with supplied wire ties. (Electra/Ultra/Street Glide) BAGGER AUDIO™ LIDS INSTALLATION- Detach factory lid by removing the 2 screws holding the factory strap to inner lid and 5 small torque screws holding lid to factory latch assembly. (Consult factory service manual for further instructions) Remove metal strap from behind factory seal (This is the metal strap that the previous 5 small torque screws were removed from) Position metal strap in same location on your new lid. (If you purchased your product unpainted, you must install the supplied seal to your finished lid) Reattach BAGGER AUDIO™ LIDS by installing the 5 small torque screws in the same location as on the factory lid. (We suggest that you have an assistant hold the lid in place while attaching your new lids) Replace factory nylon Hinge straps with new nylon straps supplied in kit. Use metal straps and machined screws to secure the nylon hinge straps. 
 Place a small bead of silicone on the inside rim of the speaker basket to create a watertight seal between the inside of the lid and the speaker. 
 Install speaker into the bottom of the lid (not through the top opening) with supplied stainless screws and washers (4 per lid). Be sure to center speaker in lid opening to ensure proper speaker grill placement. Install speaker with terminals facing toward the front of the lid. One 1/4″ hole must be drilled in each bag. Holes can be positioned at the ownerʼs discretion. Place rubber grommet in drilled hole before running wires

FC Shock Spring Installation Guide

0

Filed Under (Tips and Review) by admin on 14-12-2010

download
Installation: 1. Remove the fork springs according to the OEM Owner’s Manual. 2. Check/adjust fork oil level and weight according to OEM Specifications. Caution: Most inverted forks will not require the use of any shim washers or spacers. In cases where use is necessary with the twin chamber style fork, the shims must be placed at the bottom of the spring. Most conventional forks (non-inverted) will use shim washers or spacers at the top of the fork spring. 3. Install Factory Connection fork springs and refer to OEM Owner’s Manual for proper assembly procedures. 4. Be sure to double check all fasteners. Note: Most modern day forks require special tools for disassembly and assembly of the components. Examples : Showa 47/49mm Twin Chamber, KYB 48mm Twin Chamber, WP 07 SX Models/SXS Components. Installing fork springs is an intricate process that should be performed with extreme care by a qualified suspension technician. Failure to install the springs correctly could cause damage to one or more components of the fork. This damage, although not readily apparent, could lead to unexpected failure or rider injury. Factory Connection manufactures models specific fork springs. Installation of a Factory Connection spring not designed for your motorcycle may result in unexpected failure and rider injury. Please consult your Factory Connection spring dealer or call Factory Connection directly if you are unsure about a spring/or springs. 1. Factory Connection’s Limited Lifetime Warranty Factory Connection warrants, to the original retail purchaser (“consumer”) who retains ownership of the vehicle on which the suspension spring(s) (“products(s)”) was originally installed, all suspension springs for life against factory defects in material and workmanship (other than defects in finish) when used under normal use and operating conditions. 2. Your Remedy Upon verification of warranty coverage, Factory Connection at its option will replace defective or prematurely worn-out product (s), without charge, or refund the purchase price of the products(s). This is the Consumer’s sole and exclusive remedy for any loss or damage, however arising, due to a nonconformity or defect in the product(s). 3. Warranty Claim Procedure To make claim under this warranty, the consumer should contact the Factory Connection dealer or Factory Connection where the product(s) was purchased. Factory Connection reserves the right to test the returned product(s) to evaluate the nonconformity or possible defect. The Consumer is responsible for all costs of returning the defective or prematurely worn-out product(s) to the Factory Connection dealer as well as all costs for removing the product(s) from and installing the products(s) on the vehicle.

Incoming search terms:

Kawasaki Exhausts – ZX-6 ZX-10 Zx-14 Exhaust – Slip-ons INSTALLATION MANUAL

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Our favorite exhaust options for Kawasaki ZX Ninjas – ZX-10,ZX-6r, and the new horsepower king, Zx-14.. Grab your horsepower today. We love Rob Muzzy and Muzzy Exhausts.Going back to Doug Chandler and Scott Russell, Muzzy has been synonomous with Kawasaki and performance – and for years, if you rode Kawasaki,and you were on the podium, Muzzy was on your exhaust. We also feature Arrow and Yoshimura exhausts for your ZX-6R, ZX-10 and ZX-14. We love the sound of a Yosh exhaust on any Kawasaki Ninja. Yoshimura Oval (RS-3) Race Slip-On for Kawasaki ZX14R 2006 The easiest and least expensive way to experience Yoshimura performance is with our Slip-On/Bolt-On lines. Bolt-On style bolts to the O. E. M. mid-pipe Slip-On style with its stainless steel easily attaches to the mid-pipe RS-1 is available where noted Usually, no jetting or re-programming is required and installation is a snap Hindle Stainless Exhaust High Head Pipes – Kawasaki ZX6R-RR 03-04 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo North Denver News http://northdenvernews.com Powered by Joomla! Generated: 19 October, 2010, 12:28 Hindle Stainless Exhaust Low Head Pipes – Kawasaki ZX9R 00-03 The worlds lightest stainless steel exhaust system. Increase horsepower and torque throughout the entire rpm range. Lightweight, strong stainless steel header design looks great and weighs less than stock headers. Available in low- and high-mo

Incoming search terms:

HARLEY DAVIDSON STAINLESS STEEL BRAIDED CLUTCH CABLE KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
REMOVE CLUTCH CABLE 1. See Figure 1. Loosen clutch adjuster to obtain slack in the clutch cable (2) by performing the following: a. Locate cable adjuster (1) and slide off rubber boot (4). b. While holding cable adjuster with 1/2-inch wrench, loosen jam nut (3) using a 9/16-inch wrench. c. Turn cable adjuster until there is a large amount of free play at hand lever. 1 2 3 4 is 00889 1. Cable adjuster (1/2-inch) 2. Cable end 3. Jam nut (9/16-inch) 4. Rubber boot Figure 1. Clutch Cable Adjuster 2. See Figure 2. Remove the retaining ring (1), pivot pin (2) and clutch cable anchor pin (3) from the hand lever. 2 3 1 is 00891 1. Retaining ring 2. Pivot pin 3. Clutch cable anchor pin Figure 2. Clutch Cable Compoments 3. See Figure 3. Drain transmission lubricant and remove fill plug dipstick. Remove the six screws that hold the clutch release cover in place. Remove the clutch release cover, being careful not to damage the gasket. NOTE The clutch release cover gasket (P/N 36801-87B) will need to be replaced if torn or damaged to prevent transmission fluid from leaking from the release cover. 4 3 5 2 6 1 is 00894 Figure 3. Clutch Release Cover Screw Sequence 4. See Figure 4. Note position of retaining ring opening. Retaining ring opening must be positioned in approximately the same location during reassembly. Remove retaining ring (1). 5 4 1 3 2 is 00895 1. Retaining ring 2. Inner ramp 3. Cable fitting 4. Clutch cable 5. Ramp coupling Figure 4. Clutch Cable Connection 5. Pull inner ramp (2) and coupling (5) out of side cover. Hold inner and outer ramps together to keep balls from falling free. 6. Rotate the inner ramp to a position that will allow the coupling (5) to be disconnected from the inner ramp lever arm. Disconnect coupling from inner ramp. Disconnect cable end from coupling. 7. Back out threaded cable fitting from side cover. Ensure that o-ring is removed with cable. Discard o-ring. INSTALL CLUTCH CABLE 1. See Figure 4. Obtain braided stainless steel clutch cable from kit. Apply a light coat of oil on new o-ring and install o-ring (Part Number 11179) onto threaded portion of clutch cable (4). Insert clutch cable fitting (3) into clutch release cover. Do not tighten cable fitting at this time. 2. Connect cable end to coupling. Rotate ramps for best access and install coupling on inner ramp. Place ramp assembly in position in side cover. 3. Install retaining ring. Position retaining ring opening so it is located approximately over the outer ramp tang (the stop that prevents rotation). NOTE Replace clutch release cover gasket if torn or damaged. 4. See Figure 3. Place gasket, if removed, on side cover and install side cover. Tighten the six screws in the order shown to 84-108 in-lbs (10-12 Nm) . 5. Tighten the clutch cable fitting to 36-60 in-lbs (4-7 Nm) . 6. Place a few drops of oil inside cable housing. 7. Route clutch cable as follows: SOFTAIL MODELS FXSTD, FLSTS, FXSTS and FXST – Route clutch cable from the clutch release cover, across the frame, up along the front frame downtubes and across the front of the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. FLSTF and FLSTC – Route clutch cable from the clutch release cover, across the frame and up along the front frame down- tubes, up to and behind the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. DYNA MODELS FXDWG – Route clutch cable from the clutch release cover, under frame and across to the left side. See Figure 5. Insert cable (1) into clip (2) at the bottom left side of the frame

Incoming search terms:

HARLEY DAVIDSON FRONT THUNDERSTAR WHEELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 08-11-2010

download
Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. -J04065 1 of 8 For FXSTD Models: Discard the tapered r ight side wheel spacer. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTE • For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771- 07, 43609-07, 44323-07, 44282-07, 44322-07, 43975-07, 43602-07 and 43773-07 install short valve stem (43157- 83A) included in the installation kit. • For Kits 40943-09, 40966-09 and 40996-09 install long valve stem (43206-01) included in the installation kit. 2. See Figure 2. Install valve stem assembly (L, M or N) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771-07, 43609-07, 40943-09, 40966-09 and 40996-09: • The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and/or DOT markings to identify it as the brake disc and primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44323-07, 44322-07 and 44282-07: • Install the wheel so that the hub markings are on the left side of the motorcycle. The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and hub markings to identify it as the primary bearing side. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). • The gross axle weight ratings is unaffected by the installation of this wheel on a vehicle equipped with a 21-inch wheel. For Kits 43975-07, 43773-07, and 43602-07: • The wheel has a machined groove (item 5, Figure 2) in the hub face to identify the right side. • For 2007 and later FX Softail Models and 2008 and later FXDWG: The left side of the wheel is the primary bearing side. For all other models the right side of the wheel is the primary bearing side. • For Kit 43602-07: An arrow is engraved into the right side hub to indicate the direction of rotation. • For Kits 43975-07 and 43773-07: An arrow is cast between the spokes on the right side to indicate the direction of rotation. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake-disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). 4. Install wheel assembly parts from the appropriate Service Parts table for this fitment and stock brake disc. Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in Service Manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in installation kit. For FXSTD Models: Install wheel kit, stock left wheel spacer and right side wheel spacer from installation kit in place of the tapered right side wheel spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install the left side wheel spacer provided in the kit between the stock left wheel spacer and the left fork. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual

Incoming search terms:

PIAGGIO Power Program with SIP Stainless Steel Joint Pipe Installation Manual

0

Filed Under (Piaggio) by admin on 28-10-2010

download
First, loosen and remove both screws between joint pipe and exhaust. Then, remove the other two upper screws, as in illustration 2, between cylinder and joint pipe. This may be a little difficult to reach. For additional ease removing screws, raise up motor frame with a crowbar or chisel. Now, remove old joint pipe and replace with SIP stainless steel pipe. Don’t forget to replace old gaskets with new gaskets, included in delivery. Join us in the SIP Article Forum for further handy tips and tricks from those in the know at www.sip-scootershop.com Turn down screws bit by bit, one after another, to ensure balanced fit, making sure to loosen muffler screws shortly. If you should have difficulty getting a good fit, here’s a tip: drill longer holes on exhaust flange to get better adjustment. Finito; put away the tools and take a test drive

Incoming search terms:

TOYOTA Tacoma 2005 – STAINLESS STEEL EXHAUST TIP Procedure

0

Filed Under (Toyota Manuals) by admin on 18-10-2011

download
Safety (eye protection, rechecking torque procedure, etc.).  Vehicle Disassembly/Reassembly (panel removal, part storage, etc.).  Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). Please see your Toyota dealer for a copy of this document. 1. Installation. (a) Make sure the vehicle’s tail pipe is free from dirt and debris. (b) Remove exhaust tip from box and set on a soft surface to prevent scratching. (c) Slide the Stainless Steel clamp over the vehicle tailpipe as shown. (Fig 1-1 & 1-2) (1) Locate the bolt of the clamp on the right side (3:00 Position) with the nut on the top as shown. (Fig 1-1) (2) Continue sliding up out of the way so it won’t interfere when you install the exhaust tip and aluminum bushing. (Fig. 1-2) (d) Slide the exhaust tip over the tail pipe with the bump facing toward the rear of the vehicle as shown. (Fig 1-3) (1) If necessary, a rubber mallet may be used to aid installation

APRILIA DORSODURO FACTORY 750 Technical Specifications

0

Filed Under (Aprilia) by admin on 06-11-2010

download
Engine type Aprilia V90 four-stroke longitudinal 90° V-twin engine, liquid cooled, double overhead camshafts with mixed gear/chain timing system, four valves per cylinder. Fuel Unleaded petrol Bore and stroke 92 x 56.4 mm Total engine capacity 749.9 cc Compression ratio 11: 1 Maximum power at crankshaft 67.3 kW (92 cv) at 8,750 rpm Maximum torque at crankshaft 8.4 kgm (82 Nm) at 4,500 rpm Fuel system Integrated engine management system. Injection with Ride by Wire throttle opening management and triple mapping Ignition Digital electronic ignition integrated with injection system. Starting Electric Exhaust system 2 into 1 exhaust system in 100% stainless steel with three-way catalytic converter and lambda probe Alternator 450 W at 6,000 rpm Lubrication Wet sump Gearbox 6 speeds, drive ratio: 1st 14/36 (2.57) 2nd 17/32 (1.88) 3rd 20/30 (1.5) 4th 22/28 (1.27) 5th 23/26 (1.13) 6th 24/25 (1.04) Clutch Multiple discs in oil bath, hydraulically operated Primary drive Straight cut gears, drive ratio: 38/71 (1.87) Secondary drive Chain. Drive ratio: 16/46 Chassis Modular tubular steel frame fastened to aluminium side plates with by high strength bolts. Removable rear subframe. Front suspension Multi-adjustable Sachs upside-down fork with Ø 43 mm diam. stanchions. Wheel travel 160 mm. Rear suspension Aluminium alloy swingarm Gas-operated shock absorber with piggy back with adjustable spring preload and compression and rebound damping. Wheel travel 160 mm. Brakes Front: Dual Ø 320 mm diam. stainless steel floating discs. Radial callipers with four pistons. Metal braided brake pipe. Rear: Stainless steel disc Ø 240mm. Single piston calliper. Metal braided brake pipe. Wheel rims Aluminium alloy Front: 3.50 X 17″ Rear: 6.00 x 17″ Tyres Radial tubeless tyres; front: 120/70 ZR 17 rear: 180/55 ZR 17 Dimensions Max. length 2,216 mm Max. width 905 mm (at handlebar) Max. height 1,185 mm (at instrument panel) Saddle height 870 mm Wheelbase 1,505 mm Trail 108 mm Steering angle 26° Tank 12 lt (range > 200 km)

Aprilia PEGASO 650 FACTORY – Technical specifications

0

Filed Under (Aprilia) by admin on 26-10-2010

download
Engine Single-cylinder four-stroke with light alloy cylinder. Liquid cooling with three way pressurised circuit. Single overhead cam with chain timing drive; four valves. Anti- vibration balancer shaft. Fuel Unleaded fuel. Bore and stroke 100 x 84 mm. Total displacement 660 cc. Compression ratio 10:1. Max. power at crankshaft 48 HP (35 kW) at 6,000 rpm. Max. torque at crankshaft 6.01 kgm ( 59 Nm) at 5,000 rpm. Fuel system Integrated electronic engine management system. Electronic fuel injection. 44 mm throttle body. Ignition Electronic. Starting Electric starter. Alternator 290 W Lubrication Dry sump with oil pump. Gearbox 5 speed. Transmission ratios: 1st 12/30 2nd 16/26 3rd 20/23 4th 22/20 5th 26/20 Clutch Multi-plate in oil bath. Cable operated. Primary drive Spur gears. Transmission ratio: 36/75. Final drive Chain. Transmission ratio: 15/44. Frame Steel, open cradle, single spar frame. Front suspension 45 mm fork. Wheel travel 140 mm. Rear suspension High strength steel swingarm. Aprilia Progressive System (APS) rising rate linkages. Sachs hydraulic monoshock with adjustable rebound and preload. Wheel travel 130 mm. Brakes Front: FTE stainless steel floating disc, ∅ 320 mm. Four piston radial caliper with radial master cylinder. Rear: stainless steel disc, ∅ 240 mm. Floating caliper

APRILIA SR 50R / DITECH FACTORY Technical Specifications

0

Filed Under (Aprilia) by admin on 06-11-2010

download
APRILIA SR 50R / DITECH FACTORY Uncompromising racing design, the most advanced engine technology of any scooter, plus unrivalled performance and handling. That is what the Aprilia SR 50 has always been about. Now the world’s only real racing replica scooter has pushed the frontiers of performance and technology even further forward. The completely new SR 50 is further ahead that ever before. Technical Specifications Engine Liquid cooled horizontal single cylinder two stroke. Electronic direct fuel injection Bore and stroke 40 x 39.3 mm Displacement 49 cc Compression ratio 11.5:1 Intake Reed valve Fuel injection Electronically controlled, air assisted, direct injection into the combustion chamber Fuel injector EFI low flow injector Direct injector External opening, SMD 8 micron medium spray Pressure regulator Pressure differential maintained at 2.5 bar Throttle body 18 mm throttle body with integrated TPS (Throttle Position Sensor) Air compressor Driven off crankshaft, lubricated by air-oil mix in crank chamber Fuel pump 6.5 – 8 bar, high pressure pump with low electrical power absorption, < 0.5 A Electronic control unit Clock Speed 8 Hz, 22 pin Ignition High power inductive ignition Starter Electric Alternator Flywheel-magneto, 165W – 12 V Lubrication Oil injection by electronic oil pump Oil tank capacity 1.2 liters (0.317 gal.) including 0.2 liter (0.053 gal.) reserve Gear box Continuous automatic converter Primary transmission “V” belt Final transmission Adapter with gears in oil bath Clutch Automatic centrifugal dry clutch Frame Split single cradle frame in high tensile strength steel Front suspension Hydraulic fork mounted on offset steering sleeve, 3.5 inches (90 mm) of travel Rear suspension Engine unit acting as swingarm; frame linkages on two radial silent block mountings, 2.8 inches (72 mm) of travel Brakes front: stainless steel 190 mm diameter disk, “racing” calliper with two opposing pistons, diameter 32 mm rear: stainless steel 190 mm diameter disk, “racing” calliper with two opposing pistons, diameter 30 mm Rims light alloy, 5 spokes front and rear: 3.50 x 13″ Tires (tubeless) front and rear: 130/60 x 13” Dimensions max. length: 73.2 inches (1860 mm) max. width: 27.8 inches (705 mm) max. height: 44.1 inches (1120 mm) saddle height: 32.0 inches (820 mm) wheelbase: 50.8 inches (1290 mm) Dry weight 198 lbs. (90 kg) Tank capacity 1.85 gallons (7 liters)