stock plot screw on trx 250ex

You search Auto repair manual PDF stock plot screw on trx 250ex, if there are search results will appear below. If search results do not exist, please search by others keyword.



  stock plot screw on trx 250ex Direct Download speed 5282 Kb/s

  stock plot screw on trx 250ex Full Version speed 6162 Kb/s



Honda TRX 400EX INSTALLATION And REMOVAL INSTRUCTIONS

0

Filed Under (Honda) by admin on 14-12-2011

download
Quiet cores are supplied with this kit but not installed. To install the quiet cores remove both rear end caps ((turn downs) and install the quiet cores with the tubes facing inward. Re-install the end caps. REMOVAL Remove seat, disconnect attery and remove. Remove front fenders and side skirts. Remove fuel tank (make sure to shut fuel off and drain remaining fuel in the line before removing). Remove stock muffler first, then remove stock headers. Retain the 4 stock header bolts to install on your new exhaust system. Remove the rear bolt from your stock air box. Loosen stock intake clamp at carburetor. Remove stock boost bottle from the side of the boot. Loosen stock snorkel clamp at the air box, remove stock retaining clip at the front of the snorkel. Remove stock air box, intake boot and snorkel together from the ATV. Slide tarter solenoid off of stock mounting prongs. Remove Phillips screws from fuse holder and remove from plastic housing. Remove plastic battery housing from the ATV. Unplug tail light from harness. Unclip harness from the 2 clips above the battery. CARBURATION Now would be a good time to replace your stock main jet, with the supplied 190 main jet and replace your stock pilot jet with the supplied 48 pilot jet. Make certain that all hoses are tight and routed as stock. Be certain carb clamp is tight when re-installed. INTAKE BOOT Remove the intake boot from the stock air box. Take an exacto knife or razor blade and trim off the rubber piece that the hard plastic snorkel slips into. Trim around the intake boot staying the same distance as the rest of the lip. Take a hax saw and cut the groove as the rest of the boot is, being
careful not to cut all the way through (Picture Fig.2).

How To Adjust the Accelerator Pump On the 40mm Mikuni Carburetor

0

Filed Under (Yamaha) by admin on 21-01-2012

download
1) The “blue” colored screw in the image is the duration adjustment screw. Underneath the head of the screw is a lock nut and the bracket arm that the screw is threaded into. To decrease the amount of fuel squirted the adjustment screw is turned “clockwise” or in. To increase the amount of fuel squirted the adjustment screw is turned “counter clockwise” or out. To get the max, amount of decrease remove the screw and take the lock nut off of the screw. Then replace the screw into the cam arm, then replace the lock nut underneath the arm on the screw. this gives you another 3/32″ of an inch in which the screw can be screwed in.
2) Turn the adjustment screw fully clockwise or IN. Start your engine, Blip your throttle open, if the engine stutters, (hesitates), it is not getting enough fuel so turn the screw counter clockwise to increase the amount of fuel squirted from the accelerator pump into the carburetor. Keep blipping the throttle and adjusting the screw till the carburetor starts to cough. Stop here and turn the screw back in till the coughing stops. Tighten down the lock nut. This should give you the best throttle response with the least amount of coughing and backfiring out the carburetor. Timing Adjustment Screw This is the “Green” colored screw just above the Blue duration adjustment screw. The” Mucker” said it best,,,,, This upper screw adjusts the “timing” of the squirt. By altering it’s setting, you can advance or delay the onset of the fuel squirt. But probably, it won’t have to be touched

Incoming search terms:

HARLEY DAVIDSON REAR SADDLEBAG GUARDRAILS INSTALLATION MANUAL

0

Filed Under (Harley Davidson, Uncategorized) by admin on 18-04-2011

download
Installation KITNUMBER 49087-01 1. Remove and save fasteners that retain saddlebag guardrails. 2. Replace stock saddlebag guardrails with new guardrails from kit. 3. Screw in and torque each stock fastener as follows: a. Four stock screws, Part No. 3678, using two new locknuts (1), Part No. 7667. Torque each screw to 19 ft-lbs. b. Two stock screws, Part No. 3601 using two new locknuts (2), Part No.7686. Torque each screw to 9 ft-lbs. For Domestic FLHRC/I Vehicles Only. (Does not apply to Harley Davidson International (HDI) vehicles): Federal Motor Vehicle Safety Standard (FMVSS) 108 requires all motorcycles to be equipped with side reflectors. Install, or have Dealer install, the reflectors, Part Nos. 59370-98 and 59371-98, which are purchased separately. Loss of visibility to other motorists could result in death or serious injury. 1. See Service Parts illustration. Position reflector so it is centered on the vertical portion of the saddlebag guard 1″ above the top end of the lower bend where the radius turns upward. Measure and use a small piece of tape to mark location for attachment of the lower edge of the reflector at the 1″ mark. 2. Remove protective tape backing from one reflector. Locate reflector above the 1″ mark. Apply reflector, using even pressure by rubbing back and forth on reflector. Repeat for other side. Note Reflectors are specific for each side. Reflectors have a flat end and a curved end. The curved end goes down. Top edge should be horizontal when positioned on guard. If not, reflector is for opposite side. KITNUMBER 49088-01 1. Remove and save fasteners that retain saddlebag guardrails. 2. Replace stock saddlebag guardrails with new guardrails from kit. 3. Using four hexsocket button head screws (4) removed earlier, attach saddlebag guards using the remaining two existing holes in each guardrail. 4. Screw in and torque each stock fastener as follows: a. Four stock screws, Part No. 3678, using two new locknuts (1), Part No. 7667. Torque each screw to 19 ft-lbs. b. Two stock screws, Part No. 3601 using two new locknuts (2), Part No.7686. Torque each screw to 9 ft-lbs

BMW R1200RT Sport/ Touring 1100X Kit Installation Manual

0

Filed Under (BMW) by admin on 17-12-2010

download
Step 1 — Locate ‘mold circle’ indentation on each side fairing panel (Pic 1). With panel mounted on bike, this indentation is center, at rear inside panel edge, and faces inside. Temporarily install bracket as shown in (Pic 2), align bottom bracket hole over indentation and mark for hole. Remove brackets at this time. Step 2 — Remove fairing body side panels. Four screws per side required for removal, see owners manual. Drill a 3/8″ hole at mark. If harness kit has not been installed, do not re-install left side panel until finished unless you remove tank to install harness. Removal of the tank is the best option to route harness from battery area to front of the bike. Step 3 — As required, re-install fairing body side panels. Do not re-install the top factory inner panel Torx Screw yet, as you will re-use this screw to secure the top light bracket mounting hole to the fairing panel. Step 4 — Using 10/32×1/2 screws and black shoulder washers from Hardware package, secure lights to PIAA Ezy-Mount® brackets (See Pics 3 & 4). Right side bracket is stamped ‘EZY-MOUNT’. See note below for Powersports lights. Due to close proximity of the light body to fairing side panel, access to the vertical adjustment screw on the panel side of the light will not be possible after installation. To prepare for this; before installing bracket/light assembly to panel, make sure this screw is tightened so that you can barely move the light body. After bracket is installed, final vertical adjustment can be secured with the inside screw. Torque on this screw is adequate to hold vertical adjustment, and the screw that faces the panel will not come loose. NOTE: WHEN INSTALLING POWERSPORTS LIGHTS, YOU MUST INSERT THE SHOULDER ADAPTER WASHER INTO THE LIGHT FOOT, BEFORE INSERTING SCREW TO SECURE LIGHT FOOT TO BRACKET. THIS ADAPTER CENTERS LIGHT FOOT OVER PEMNUT (TIGHTEN THIS SCREW SECURELY). Step 5 — Insert well nut into previously drilled 3/8″ hole. Place bracket assembly against fairing, aligning top hole with the top fairing mounting position; re-install the factory Torx screw at this location. Adjust as necessary and install the second supplied SS 10/32 x 5/8 Torx screw thru the lower bracket mounting hole to the well nut. With constant pressure on the screw, tighten securely. Constant pressure ensures that the rear expandable section of the well nut captures the back of the plastic inner panel as you tighten the screw. Future removal of fairing panels is now possible with light assembly installed (utilizing the bottom bracket mounting screw), thus re-alignment of lights is not required after normal maintenance.

HARLEY DAVIDSON FLSTN SADDLEBAG GUARD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
REMOVAL All Models 1. If equipped with saddlebags, removal may ease installation. Follow the instructions in the appropriate Service Manual or Instruction Sheet. 2. See Figure 1. Remove and discard the forwardmost fender support bolt (1). Repeat for the other side. 3. See Figure 2. On the left side, remove the footrest support mounting bolt (1) and footrest support bracket assembly (2). Discard the mounting bolt. 2005 – 2006 Models 1. Loosen the exhaust shields as necessary following the instructions in the appropriate Service Manual. Move as necessary for access. 2. Loosen the exhaust header nuts following the instructions in the appropriate Service Manual. 3. See Figure 3. Remove bolt (1) connecting the exhaust system (2) to the support bracket (3). 4. See Figure 4. Remove the two rear muffler bracket bolts (1). 5. See Figure 5. Move mufflers enough to access the rear bolt attaching the exhaust mounting bracket to the frame. Remove bolt (1) and discard. 2007 – Later Models NOTE On 2007 – later models, the frame tab (4) has a plug instead of a bolt (see Figure 6, item 1). 1. Remove plug and discard. 1 is05313 1. Fender support bolt (discard) Figure 1. Remove Docking Hardware 1 2 is05320 1. Footrest support mounting bolt 2. Footrest support bracket assembly Figure 2. Footrest Support Bracket Assembl NSTALLATION Right Side See Figure 5 or Figure 6. 1. See Figure 7. Install upper screw (7) in the fender support. Tighten screw finger-tight. 2. Install the lower screw (4 or 5) with the saddlebag guard, washer (9) and locknut (6) inside the frame. Tighten screw finger-tight. 3. Tighten the upper screw to 30 ft-lbs (41 Nm) . 4. Tighten the lower screw to 40 ft-lbs (54 Nm) . Tighten nut to 30 ft-lbs (41 Nm) . 5. 2005 – 2006 Models: a. Loosely install the exhaust header bolts. b. See Figure 4. Loosely install two rear muffler bracket bolts (1). c. See Figure 3. Loosely install bolt securing exhaust system (2) to support bracket (3). d. Tighten exhaust header bolts following the instructions in the appropriate Service Manual. e. Tighten support bracket bolt and rear muffler bracket bolts following the instructions in the appropriate Service Manual. f. Tighten exhaust shields following the instructions in the appropriate Service Manual. 6. Install saddlebag (if removed) following the instructions in the appropriate Service Manual or Instruction Sheet. 1 2 3 4 is05333 1. Lower saddlebag guard screw 2. Upper saddlebag guard screw 3. Saddlebag guard 4. Exhaust support bracket Figure 5. Install Saddlebag Guard – Right Side Shown (2005 Models) -J04645 2 of 4
2 1 3 4 is05332 1. Lower saddlebag guard screw 2. Upper saddlebag guard screw 3. Saddlebag guard 4. Frame tab Figure 6. Install Saddlebag Guard – Right Side Shown (2007-Later Models) Left Side 1. Loosely install upper screw (7) through the saddlebag guard and the fender support. NOTE Spacer (8) must be installed with the chamfer facing out. 2. See Figure 7. For 2005-2006 Models: Install lower screw (3) through the saddlebag guard, saddlebag guard spacer (8), footpeg support and the frame. Tighten to 30 ft-lbs (41 Nm) . For 2007 and later Models: Install lower screw (10) through the saddlebag guard, footpeg support and the frame. Tighten to 30 ft-lbs (41 Nm) . 3. Tighten upper screw to 30 ft-lbs (41 Nm)

Incoming search terms:

HONDA TRX 400EX Removing Stock Carb and Cables INSTRUCTION

0

Filed Under (Honda) by admin on 21-12-2011

download
Remove seat/fender assembly and fuel tank. 2. Remove throttle cables paying close attention to routing. 3. Remove thumb throttle housing if you are installing a twist throttle. 4. Remove air box and air box intake tube. 5. Remove stock carburetor. 6. Stuff a clean rag into intake manifold to keep debris from entering engine. Preparing machine for carburetor installation 1 . Route the provided throttle cables per manufacturer’s recommended procedure, routing them the same as the stock cables. 2 . Remove the rubber alignment tabs from the manifold using a razor blade or cutters. Be very careful not to damage the intake manifold! 3. Remove air box intake tube from the air box and use a hacksaw to cut approx. 1½” off of the air box intake tube. Your tube should resemble the one shown in Figure 1. Re-assemble the air intake tube into air box and install back onto bike. Don’t forget to tighten clamp around intake tube and reinsert crank vent into the air boot. Figure 1. Thumb Throttle Attach cable into cable wheel with the cable end at the 8: 00 position of the cable wheel, then into bracket. Secure by replacing the cable bracket end and phillips screw. See Figure 2. Figure 2. Twist Throttle 1. Install the pull (see figure 4 for cable identification) , cable end into the 8: 00 position and the idle cable end into the 11: 00 position on the cable wheel. See Figure 3

HARLEY DAVIDSON SADDLEBAG SUPPORT (DRESSER BAR) KIT CHROME INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 18-03-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Refer to the Service Manual and follow the instructions to remove the seat and disconnect the negative battery cable. 2. Remove the saddlebags. Refer to SADDLEBAG REMOVAL in the Service Manual. NOTE See Figure 1. Item 12 covers saddlebag side rails, front guard and lower support removal for FLHT/C/CI/CUI, FLTR/I, FLHR/C and FLHR/I/CI models and item 13 cover removal for lower saddlebag support and front guard for FLHR/I/CI models. 3. See Figure 1. Gently pull one side cover (1) from the frame downtubes (no tools are required). 4. Remove the 5/16-18 hex head screws (not shown) and lockwashers (not shown) that secure the muffler to the muffler support (2). Save the muffler mount bracket, rubber mount from the old saddlebag lower support, 5/16-18 hex head screws and lockwashers. 5. With a T-40 TORX® driver, remove and discard the outside 5/16-18 TORX pan head screw (3) and 5/16-18 locknut (4) that secure the lower saddlebag support to the rear bumper and fender support. 6. Remove and discard the inside 5/16-18 locknut (5). Leave in, the inside 5/16-18 TORX pan head screw (6), to keep alignment TORX driver, remove and discard the 3/8- 16 TORX pan heaof the rear bumper rail to the rear bumper and fender support. 7. With a T-40 TORX driver, remove and discard 5/16-18 TORX pan head screws (7) that secure the horizontal side rail saddlebag guards to the fender mounting support. 8. With a T-40 d screw (8) and 3/8-16 locknut (9) that fastens the lower flange of the front saddlebag guard to the motorcycle frame. 9. With a T-40 TORX driver, remove and discard the 3/8- 16 TORX pan head screw (10) that fastens the upper flange of the front saddlebag guard to the frame. Remove the saddlebag guard with the rails and discard. 10. Repeat Steps 3 through 9 for the opposite side. 11. See Figure 2. The new chrome saddlebag supports are side-specific. Take the chrome left (1) (not shown) or right (2) side support from the kit and place it in position on the vehicle frame. Insert a 3/8-16 x 7/8 in long TORX pan head screw (5) and 3/8-16 locknut (6) from the kit through the front flange of the new support and into the vertical frame tube. Do not tighten the screw at this time. 12. Obtain the 5/16-18 x 1in long TORX hex socket screw (3) and 5/16-18 locknut (4) from the kit. Insert screw through the outside hole (A) mounting tab on bumper and fender bracket and also through rear flange in new support and thread locknut onto screw and finger tighten. 13. See Figure 1. Remove old screw (6) from the inside hole of bracket. See Figure 2. From the kit, insert new 5/16-18 screw (4) into the inside hole (B) of bracket and thread locknut (5) on screw. 14. Tighten the front screw, then the rear screws and locknuts to 15-20 ft lbs (20.3-27.1 Nm) . 15. Install the muffler mount bracket and rubber mount saved from Step 4, into the new lower chrome support bracket (8). 16. Secure the muffler to the new chrome support bracket (8) with 5/16-18 hex head screws and 5/16 lockwashers (not shown) saved from Step 4. 17. Tighten the screws and locknuts to 15-20 ft lbs (20.3-27.1 Nm) . 18. Repeat Steps 11 through 16 for the opposite side

HARLEY DAVIDSON XL STARTER MOTOR COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 13-03-2011

download
Installation 1. Remove exhaust system according to Service Manual instructions. 2. See Figure 1. Remove the outer primary screw shown and retain it for reinstallation. 3. See Service Parts Illustration. Insert the thread cleaning screw (9), through the primary cover and the crankcase until the full screw diameter protrudes through the crankcase. Remove any debris from from the tip of the thread cleaning screw. Remove thread forming screw and discard. NOTE If thread cleaning screw binds in crankcase hole, remove thread cleaning screw and chase threads with 1/4 – 20 tap. 4. Install set screw (8) from outer primary side using the wrench provided. Set screw should extend past the crankcase approximately .375″. 5. With wrench in set screw to prevent rotation, install the backplate over the set screw and fasten with the 1/4-20 nylock nut (5). 6. Reinstall the primary cover screw saved in Step 1. Torque to 80-110 in-lbs (9-12 Nm). 7. Remove the the oil hose clamp from the starter stud. Do not remove the clamp from the hoses. 8. Replace the original equipment starter stud with stud (7) provided. Torque to 39-65 in-lbs (4-7 Nm). 9. Install bracket (2) over stud (7) and fasten with #10-24 nylock nut (6). Rotate bracket until the tab on the bracket rests on starter motor. 10. Install oil hose clamp onto bracket (2) using one of the #10-24 screws (4). Tuck the hoses down as far as possible without contacting the drive belt or kinking the hose. Contacting the drive belt or kinking the hose may cause damage to the hoses or powertrain. 11. Install the cover (1) to the backplate (3) and bracket (2) using four of the #10-24 screws (4) with the wrench provided. The cover should fit inboard of the gear cover and partially on top of the sprocket cover. Start the bracket screw first, then follow with the (3) backplate screws. 12. Reinstall exhaust system according to Service Manual Instructions

2000-2010 KTM X2 SWITCH WIRING HARNESS Removal and Installation Manual

0

Filed Under (KTM) by admin on 25-01-2012

download
The included 3600-SWHA switch harness is intended for use with offroad models that do not come with a Hi/Low beam switch from the factory. The harness is compatable with stock AC lighting electrical systems as well as high output DC electrical systems. 1. Remove the stock numberplate or headlight. Remove the stock kill switch from handlebars and replace with the 3600-SWHA switch. 2. Remove the gas tank. Route the white and black leads from the 3600-SWHA under the tank following the wires from the stock kill switch. Disconnect the stock kill switch bullet and connect the white wire of the 3600-SWHA to the wiring harness. Disconnect the stock kill switch ring terminal and connect the ring terminal of the 3600-SWHA. Fully remove the stock kill switch. Be sure all the wires are safe from being burned or pinched and re-install the gas tank. 3. Disconnect the two female spade terminals from the stock headlight switch (if present). Connect the terminal with the yellow wire to the red power lead from the switch. Connect the white wire to the blue accessory output from the switch. Be sure the clear silicone sleeves are covering the stock plastic housings. 4. Connect the X2 headlight to the switch headlight plug. Note: The stock headlight plug will not be used for the X2 installation, but is still functional for connecting the stock headlight. The stock plug will turn on and off with the new headlight switch, and will be powered in either of the Low or High Beam positions

Incoming search terms:

Yamaha FZ-1 TiForce exhaust system Installation Instructions (Slip-on)

0

Filed Under (Yamaha) by admin on 03-01-2012

download
Loosen the clamp where the stock tailpipe connects to the stock collector. 2. Remove the bolt holding the stock muffler assembly to the footpeg/exhaust bracket. 3. Remove the stock tailpipe and exhaust assembly as one piece. 4. Remove the nut securing the right side center stand support bolt. Install the new supplied bracket as shown in (See figure 1) 5. Remove the right rear footpeg assembly complete, bolt the new footpeg mounting bracket in place of the stock one using supplied bolts. 6. Carefully unbolt the footpeg from the bracket (Be careful there are springs and washers that will fall out if you are not careful), bolt the footpeg into the new billet footpeg bracket. Bolt the footpeg bracket to the footpeg- mounting bracket. (See figure 2) 7. Remove the stock exhaust gasket from the stock tailpipe and installthe gasket into the new tailpipe. 8. Slide the supplied clamp over the new tailpipe and slide the new tailpipe onto the stock collector. 9. Slide the TiForce end can into place. Loosely attach the two rubber bands, stainless steel bands K, and stayarm / hanger G to the end can using the supplied 6mm hardware H. See figure 4. 10. Place the bands approximately 150mm from the edge of the end can. See figure 5. 11. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 12. Attach the supplied springs to connect the tailpipe and muffler assembly. 13. Make sure the exhaust system is free and clear, if necessary jigglethe system to adjust for proper clearance. 14. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (figure 5), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure thatthe rubber pads fully cover the band(s). USE CAUTION WHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 15. Tighten the supplied clamp to secure the new tailpipe to the factory collector. 16. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 17. Check that all hardware is tightened, then start the motor and check for exhaust leaks.