stratoliner blinker cover

You search Auto repair manual PDF stratoliner blinker cover, if there are search results will appear below. If search results do not exist, please search by others keyword.



  stratoliner blinker cover Direct Download speed 5282 Kb/s

  stratoliner blinker cover Full Version speed 6162 Kb/s



V-Star 1100 And Dragstar 1100 Modification V-Star Driving/ Passing Lights Factory Chrome Light Bar Cover Installation

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. Use a rotary tool to widen the fastening area of the lower backside clips on the cover. The total width between the clips should be 4 æ inches. Trim off º inch on both inside ends of the lower backside attachment clips. Trim the clips equally. The following picture shows a modified cover. Narrow the clips on both ends to fit over the welds on the bar. The cover will not attach to the bar if the width between the clips is too narrow. If the width is too wide the cover may slide sideways on the bar. Narrow both clips equally to center the cover over the welds on the lower edge of the bar. The top of the cover is modified to allow the cover to fit over the bolts on the light bar. The top edge of the cover is filed æ inch deep and 5/8 inch wide to fit over the bolts. The back top edge is filed or ground 1/8 inch to fit over the light bar fastening bracket. Use care when filing chrome covered plastic. The following picture will help to complete this step in the modification. Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. The ends of the cover are modified to allow the cover to fit over the upward curved light bar. The upper openings on the ends of the cover that fit over the bar must be filed to enlarge the area. Grinding the cover ends will allow the cover to fit and clip onto the bar. The end openings are filed or ground at an angle to match the slope of the bar. This picture shows the outer end of the cover. The ends of this cover have been modified by enlarging the area on the upper edges to fit over the upward curving light bar. The ends must be enlarged 1/8 inch on the top edge. The cover edge can be slanted upward to match the curved bar. Modify the cover ends until it fits without the outer chrome cover touching the bar. Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. Sometimes the modified light bar cover may touch the bottom of the headlight. Modify the cover, or adjust the bar or headlight if you notice the headlight touching the bar cover. This modification makes the V-Star motorcycle with Yamaha driving lights look better. The light bar bolts are covered and the chrome cover improves the appearance of the front of your bike. Other V-Star riders will notice how nice the front of your bike looks with the chrome light bar cover installed

Incoming search terms:

HARLEY DAVIDSON DERBY COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
These kits are designed for installation on all 1999 and later 1340 Evolution and Twin Cam equipped models.INSTALLATION For models equipped with left side exhaust pipe: Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) NOTE Remove clutch inspection (derby) cover with motorcycle upright, not on side stand. If cover is removed with motorcycle on side stand, primary fluid will leak out of primary chaincase. 1. On models so equipped, remove the left-side passenger footboard. Using a T27 TORX® drive head, remove the derby cover from the primary chaincase. Discard the derby cover and fasteners. NOTE The gasket between the clutch inspection cover and the chaincase cover must be removed and all oil must be wiped from the gasket and groove in chaincase cover each time the cover is removed. 2. Remove the gasket from the groove in the chaincase cover and mounting surface. 3. Inspect gasket for tears or damage. Replace as required with gasket 25416-99C (sold separately). NOTE If installing the Derby cover on a 2006 and later Dyna, 2007 Softail, or 2007 Touring model, the original equipment gasket must be discarded and replaced with Derby Cover Gasket 25416-99C (sold separately). 4. To avoid punching holes in the clutch inspection cover gasket or enlarging the existing holes, install the new derby cover and gasket as follows: a. Align the triangular shaped hole in the gasket with the top hole in the derby cover. Be sure the rubber molding and the words “towards clutch” face the motorcycle. b. See Figure 2. Place a washer (2) from the kit onto the threads of one of the new screws (3). Insert the screw threads through the top hole in the derby cover, and carefully thread it all the way through the triangular shaped hole in the gasket. Do not push the screw through the hole. c. Hang the derby cover on the primary chaincase cover flange by starting the top cover screw. d. Start the remaining four screws and washers. 5. Install gasket (part number 25416-99C) and derby cover (1) on primary chaincase cover using screws and washers from the kit. Tighten screws to 84-108 in-lbs (10-12 Nm) in the sequence shown in Figure 1

Incoming search terms:

HARLEY DAVIDSON ENGINE/ TRANSMISSION INTERFACE AND TOP COVER INSTALLATION

0

Filed Under (Harley Davidson) by admin on 25-12-2010

download
1. Refer to the Owner’s Manual and follow the instructions given to remove the maxi-fuse. 3 1 2 is02998 1. Transmission top cover screw (4) 2. Oil spout assembly screw 3. Upper bearing housing screw (2) Figure 1. Interface Cover Installation 2. See Figure 1. Remove and retain the four socket head cap screws (1) that fasten the front and right side of the transmission cover. See Figure 3. Obtain the chrome top interface cover (3) from the kit. NOTE The top interface cover can be carefully brought into position on top of the transmission housing from either the right or left side without removing or loosening any vehicle components. 3. Position the top interface cover over the transmission top cover. Loosely fasten the chrome cover to the top of the transmission housing with the screws removed in Step 2. 4. Obtain the chrome filler neck cover (4), 1/4-20 socket head screw (5), flat washer (6) and spacer (7) from the kit. Remove the oil level dipstick from the oil spout on the side of the transmission housing, wipe off and set it aside for later installation. NOTE Insert a clean shop rag into the oil spout opening while the dipstick is not installed. With the dipstick removed, small parts or other foreign material could fall into the transmission, leading to equipment damage or malfunction. 5. See Figure 1. Remove and discard the socket head cap screw (2) that fastens the oil spout assembly to the transmission housing. DO NOT remove the oil spout from the vehicle. 6. Place the flat washer over the threads of the new screw, and insert the screw into the unthreaded hole in the chrome filler neck cover. Place the spacer onto the screw threads. Apply a few drops of Loctite® 243 (Blue) to the screw threads, and position the chrome cover onto the oil spout on the transmission housing. Lubricate the filler neck gasket with soapy water to aid in installation. Tighten the screw to 84-132 in-lbs (9.5-15 Nm) . 7. See Figure 3. Obtain the chrome lower side interface cover (1), one #10-24 socket head screw (8) and one chrome flat washer (9) from the kit. NOTE For models with mid controls, the right-side rider footrest (foot peg) support bracket must be loosened to allow installation of the lower side interface cover. After the cover has been installed, tighten the footrest bracket attaching screws to 25- 35 ft-lbs (34-47 Nm) . 8. Position the cover around the chrome filler neck cover installed in Step 6. Loosely fasten the cover to the threaded hole in the filler neck cover with the screw and washer. 9. Obtain the chrome upper side interface cover (2), three #10-24 socket head screws (8) and three chrome flat washers (9) from the kit

Incoming search terms:

HARLEY DAVIDSON VRSC FUEL TANK SIDE COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
INSTALLATION 1. Note the left and right areas on frame where the covers will be installed. Using a 50/50 mixture of isopropyl alcohol and water, thoroughly clean the frame tubes surrounding the fuel cell on the left and right sides. Let dry completely. 2. Unlock and open seat. NOTE Loosening the ignition/light switch screw (in the following step) will allow much easier alignment of the ignition/light switch cover and ignition/light switch during installation. 3. See Figure 1. At area inside of frame rail just above the ignition/light switch housing, loosen the ignition/light switch screw just enough to allow the ignition/switch switch to move slightly from side to side and up and down. Do not completely remove screw 4. See Figure 4. Obtain the right side cover bracket (ignition/light switch side) from kit. 5. Remove the strips protecting the adhesive at all of the raised sections on the cover. 1 2 is 02045 1. Ignition/Light Switch Screw 2. Ignition/Light Switch Figure 1. Loosen Ignition Switch Assembly 6. See Figure 2. Carefully align the right side cover between the three frame tubes. Beginning with the left portion of the cover, press the cover between the upper and lower frame tubes until the raised portions of cover (with adhesive) begin to snap into place. While carefully aligning the right portion of the cover, move the ignition/light switch as necessary until centered within hole in cover, then firmly press into place. Adjust ignition/light switch until the switch is centered within cover. Make sure all raised locations (with adhesive) are firmly contacting the upper and lower frame tubes and that cushion rests against front vertical frame tube. 7. See Figure 1. Tighten the ignition switch screw to 6-10 Nm (53-88 in-lbs ) . NOTE The right side (ignition/light) switch cover surface can be damaged by the key fob (from vibration) when the key is in the ignition and the bike is running. You can either remove the key fob so it does not damage the cover surface, or you can install the plastic clear sheet (included in kit) onto the side cover for protection. 8. If desired, perform the following to install the plastic clear cover onto the ignition/light switch cover. a. Obtain the plastic (rhino) sheet and hold up to the switch cover to determine proper orientation and spacing. b. Carefully peel the adhesive backing from the plastic sheet and position onto the cover. Use a wet sponge, and working out from the center, rub out any bubbles or overlapped areas under the sheet. Allow to dry completely.

HARLEY DAVIDSON SOFTAIL TRANSMISSION TOP-COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION – TOP COVER 1. See Figure 3. Remove and retain the stock screw (J) from the top of the transmission upper cover (I). 2. Ease the left side of the cover through the right side of the engine. You may need to angle the transmission cover slightly as you work it into position. 3. Fasten the weld-nut end of the top-cover bracket (2) to the top cover (4) using the screw (3) from the kit. Torque the screw to 6.6 – 9 ft-lbs (8.9 – 12.2 Nm). 4. Fasten the top of the top-cover bracket (2) to the left side of the transmission upper cover using the screw (J) removed in step 1. Torque the screw to 8 – 10 ft-lbs (10.8 – 13.5 Nm). 5. Install the Softail transmission-interface cover (D). Go to the next section in this instruction sheet. NOTE Save the washer (1) from this kit for transmission-interface cover installation. INSTALLATION – INTERFACE COVER 1. See Figure 1. Remove the screw (1) from interface cover at location 1. Keep the screw for installation. 2. Loosen the screw (2) at location 2 approximately three turns. 3. See Figure 2. Position the slotted hole (1) on the interface- cover mounting bracket (2) behind the washer at location 2. 4. Install the screw (4) from Step 1 through the mounting hole on the bracket and into location 1. Tighten the screw to 7 – 9 ft-lbs (9.5 – 12 Nm). 5. Tighten the screw (3) in location 2 to 13-16 ft-lbs (17.6 – 21.7 Nm). 6. See Figure 3. Place the interface cover (D) in position on the motorcycle. Spread the oil-line grommet (E) to wrap around the oil lines, then re-position the grommet in the interface cover. The edge of the interface cover must overlap the top of the top cover

Incoming search terms:

HARLEY DAVIDSON TIMER COVER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
INSTALLATION Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) NOTE For kits 32972-04A, 32924-04A, 32675-04A, and 32923-04A, refer to step 1 and 2 for installation instructions. To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. See Figure 2. Remove and discard the original screws and timer cover. 2. Place new timer cover (1) in position and secure with chrome screws (2). NOTE For kits 32584-88TA, 32668-98A, and 32571-98A, refer to steps 3 through 8. 3. Use a 3/8 in. drill bit and drill the heads off the original timer cover rivets. Remove original timer cover. NOTE If the inner timer cover has been riveted in place and access to the cam position sensor is required, use a left hand drill and carefully remove the rivet heads. If a right hand drill is used, the sensor plate screw heads could break off when trying to remove the rivet. NOTE To make the cam position sensor tamper proof, follow steps 4 through 6. If the cam position sensor is not required to be tamper proof, skip steps 4 through 6. 4. Remove and discard inner cover retaining screws. Leave gasket (if used) and inner cover in position. 5. See Figure 1. Place washers (4) over rivets (3) and place rivets into inner cover holes so the backs of the rivets go into the sensor plate screws’ tapped holes. 6. Use a standard rivet tool and install rivets, securing inner cover to sensor plate screws. 7. Use the self-tapping screw (5) to cut threads into the remaining inner cover holes. Discard screw after use. 8. Place new timer cover (1) in position over inner cover (A) and secure with chrome screws (2). NOTE For kit 32581-90TB, refer to steps 9 and 10. 9. Use 3/8 in. drill bit and drill the heads off the timer cover rivets. Remove original timer cover. 10. Place new timer cover in position and secure with chrome screws (Part Number 9462) from kit

Incoming search terms:

YAMAHA V-Star 1100 Motorcycle Enhancements Remote Oil Filter Installation Manual

0

Filed Under (Yamaha) by admin on 10-11-2010

download
Removing Your Old Filter and Beauty Cover In order to install the new Remote Oil Filter Kit, you’ll need to remove the stock Yamaha “beauty cover” and the old filter and filter cover. Remove the engine parts necessary to access the stock filter as outlined in the V-Star owner’s manual. The parts should come off in this order: 1. Muffler assembly 2. Front exhaust pipe 3. Rear brake reservoir cover bolt and brake cover (the reservoir should not be removed, it can remain in place and be moved aside as needed) 4. Right floorboard (this can be simply loosened, by loosening the two bolts underneath) With the above parts removed, you can remove the Allen bolts holding the beauty cover and filter cap from your engine. There are five Allen bolts holding the beauty cover (so named, because most of the cover just covers the chromed side of the engine There are five bolts holding the cover. Ignore the three on the “Yamaha” cap in the middle – these just hold the Yamaha cap to the beauty cover itself. One bolt is hidd – in this picture – just be the Yamaha ca en low p. The bottommost bolt on the beauty cover will likely leak some oil when you remove it – it holds on the inner oil filter cover. Once you remove the beauty cover, you can remove the oil filter cover, and the oil filter Keep these two “O” rings, you’ll need them for the remote kit Old oil filter. Toss it away; you’ll never need one again! Throw away the old filter, and carefully remove the orange and black “O” rings from the filter cover (see picture above). These two “O” rings will go on the new engine cap in the same order as on the old filter cover. “O” ring for bottom bolt. When the beauty cover and filter cover are removed, be sure not to lose the tiny “O” ring that the bottom bolt goes through. Preparing the Remote Oil Filter Kit Remove the orange and black “O” rings from the stock filter cover plate, and place them on the Remote Oil Filter Kit engine cap – black on the inside, orange on the outside – just like on the stock filter cover.

Incoming search terms:

HARLEY DAVIDSON CHROME BILLET LIFTER-COVER KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 25-02-2011

download
Installation with Stock Pushrods Refer to the service manual for your motorcycle model. Installation with Adjustable Pushrods Lifter-Cover Removal Installing or removing the pushrods with the valve train loaded can result in engine damage. On the cylinder being serviced, always set the lifters to the base circle on the cam before servicing pushrods, lifters, rocker arms, and valves. 1. Set the lifters of the rear cylinder to their lowest point, or base circle, on the cam. Refer to Setting the Lifters to the Base Circle in this instruction sheet. 2. See Figure 1. Insert a screwdriver into the slot on the side of the spring-cap retainer on the pushrod cover. 3. Press the spring-cap and retainer down while pulling outward to remove the spring-cap retainer. 4. See Figure 2. Lift the lower pushrod cover to reveal the lower third of the pushrod. 5. If the engine has stock pushrods installed and you are installing adjustable pushrods with this lifter-cover installation, go to step 6. If the engine already has adjustable pushrods installed and you are installing adjustable pushrods with this lifter-cover installation, go to step 7 6. Use a bolt cutter or similar tool to cut the stock pushrod. Avoid cutting the pushrods with a saw, grinder, or other method that may allow metal debris into the engine. Go to step 8. 7. Loosen the jam nut on each adjustable pushrod and resize each rod to its shortest length. 8. Remove the pushrod covers and pushrods from the engine. 9. Remove the O-rings from the seats in the engine at the top and bottom of the pushrod cover. 10. Remove the four screws fastening the lifter cover to the engine to remove the cover and gasket. 11. Remove old lifter-cover gasket material from the engine, taking care not to allow material to fall into the engine. Continue to Lifter-Cover Installation in this I-Sheet. Lifter-Cover Installation 1. See Figure 3. Verify that the lifter anti-rotation pin is in position. Installing or removing the pushrods with the valve train loaded can result in engine damage. On the cylinder being serviced, always set the lifters to the base circle on the cam before servicing pushrods, lifters, rocker arms, and valves. 2. Verify that the cylinder lifters are set to their lowest point, or base circle, on the cam. Refer to Setting the Lifters to the Base Circle in this instruction sheet. 3. Fasten the new lifter-cover gasket and chrome billet lifter cover to the engine using the chrome screws from this kit. In a cross pattern, torque the lifter-cover screws to 90 – 120 in-lbs (10.2 – 13.6 Nm). 4. See Figure 4. Loosen the jam nut on all of the pushrods and adjust the pushrods to their shortest length. NOTE See Figures 4 and 5. Install the narrow-band pushrods in the cylinder-intake location. Install the wide-band pushrods in the cylinder-exhaust location. 5. Assemble the O-rings (purchased separately) and pushrod covers. 6. Install the pushrods with the pushrod covers. The adjustment-end of the pushrod must be on the lifter

Incoming search terms:

HARLEY DAVIDSON CHROME BATTERY COVER TRIM REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-03-2011

download
REMOVAL 1. See Figure 3. Remove button-head screw (A) that attaches battery cover (B) to battery tray (C). 2. See Figure 1. Remove battery cover by lifting it over the two tabs on the battery tray. NOTE The original equipment battery cover trim has four pinch tabs on the reverse side that attach it to the battery cover. 3. See Figure 2. Remove original equipment battery cover trim from battery cover by pushing the four pinch tabs out of the battery cover using a pliers or suitable tool. INSTALLATION 1. Place battery cover over the two tabs on battery tray (C) and attach it to battery tray with button-head screw (A). Tighten screw to 20-40 in-lbs (2.3-4.6 Nm). 2. Obtain chrome battery cover trim (1) from kit. 3. Using a 50/50 isopropyl alcohol/water solution, thoroughly clean the surface where the chrome trim will be installed. Let it dry completely. NOTE Test the trim mount fit prior to removing the adhesive backing from the chrome battery cover trim. 4. Remove adhesive liner from the chrome battery cover trim. NOTE The ideal temperature should be at least 60° F (16° C) for proper adhesion of the chrome trim on the battery cover. 5. Center and install chrome trim onto the battery cover. Apply firm pressure for one minute using a cloth to prevent scratching the battery cover and battery trim. 6. Let the adhesive cure for 24 hours at no less than 60° F (16° C)

Incoming search terms:

1999-2001 DUCATI Monster INSTALLATION INSTRUCTIONS

0

Filed Under (Ducati) by admin on 25-10-2010

download
It is essential to use Blue Loc-tite on all nuts and bolts. Remove any other steering stabilizers. 2) Cover the tank with an old sweatshirt or protective device so you don’t scratch it. 3) General concept for this mount: The new key cover is the anchor point for the stabilizer, so it must be fitted correctly as per the instructions below. The base of the new key cover must sit flush all the way around to provide the support needed. The bolt lengths are critical, so be sure you read the instructions carefully so you know which bolts go in which spots! 4) Remove the (4) 8x85mm Allen bolts that hold your handlebars tight. There are plastic plugs in the tops of these bolts that must be removed before you can access the Allen head. Replace the stock top barclamp with the one provided in the kit. 5) Tighten the 4 bolts evenly so the gaps between upper and lower perches, front to back, are even. 6) Remove the (2) 6x12mm Allen bolts and the plastic key cover that covers your key switch. 7) Fit the new billet aluminum key cover over the key switch and be sure the new cover is sitting down flush all the way around on the frame. It needs to be touching the frame to function properly. We’ve machined this part to fit precisely on the bike but each bike can vary slightly due to machining variations from the Ducati Factory. The new key cover should center itself by locating on the 2 spacer/nuts underneath. You might need to loosen the 2 bolts on the underside of the frame to allow those spacer/nuts to find their centering point on our key cover. 8) Note: Your stock key switch itself has a casting knub near its base that could restrict our new cover from sitting all the way down flush. We’ve machined a clearance notch inside our part for this knub to fit into, but it is possible it could vary from bike to bike, which might require a bit more clearance filing. Be sure the key cover is sitting down flush against the frame. 9) We’ve machined the key cover to fit over a 20mm spacer nut / .805″. If for some reason the stock “spacer/nuts” are too tall, you may have to file them slightly to allow the Billet key cover to sit down flush and touch the frame. 10) Once the key switch cover is flush against the frame, all the way around it’s base, retighten the bolts that hold the spacer/nuts secure from the under side of the frame using Loc-tite. Reinstall the (2) 6x12mm stock key cover bolts to a maximum of 6-ft/lbs . The stock key cover bolts are designed to engage 6mm of thread in the spacer nut. Do not be tempted to use any longer bolts than 6x12mm or they can prematurely bottom out which will keep the key cover from tightening. Shorter than 6×12 or if the cover is not flush, makes it possible to damage the threads. Double check these key-cover bolts after your first ride, as they may loosen after initial movement from the damper

Incoming search terms:

Incoming search terms: