streetglide 2011 handlebar specs stock

You search Auto repair manual PDF streetglide 2011 handlebar specs stock, if there are search results will appear below. If search results do not exist, please search by others keyword.



  streetglide 2011 handlebar specs stock Direct Download speed 5282 Kb/s

  streetglide 2011 handlebar specs stock Full Version speed 6162 Kb/s



HARLEY DAVIDSON FLAME HANDLEBAR GRIPS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
REMOVE AND INSTALL THE LEFT GRIP 1. See Figure 1. Using a T27 TORX® drive head, remove the two screws with flat washers securing the handebar clamp (3) to the clutch lever bracket. Remove the clamp and position the clutch hand lever assembly away from the handlebar 2. Using a T25 TORX® drive head, loosen but do not remove the upper and lower switch housing screws (1). 3. Remove the end cap from the existing left handlebar grip if so equipped. Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. Do not lubricate left handlebar grip before installation. Lubricating grip can cause it to come off while riding, which could result in loss of control and death or serious injury. (00315a) NOTE Make sure that the handlebar surface and the inside of the grip are smooth, dry and thoroughly cleaned of all dirt or adhesive residue. 4. Position the new left grip (4) so the larger flange (5) is at the bottom. Push the grip fully onto the handlebar. 5. Fit the grooves (2) on the outboard side of the upper and lower switch housing over the flanges on the end of the grip, then loosely fasten the two screws. 6. Position the clutch hand lever assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the bottom of the clutch lever bracket. 7. Align the holes in the handlebar clamp with those in the clutch lever bracket, and loosely fasten the two screws with flat washers. Adjust the switch housing and clutch hand control position for rider comfort. 8. Using a T27 TORX® drive head, tighten first the upper, then the lower handlebar clamp screws to 60-80 in-lbs (6.8-9 Nm) . 9. Using a T25 TORX® drive head, tighten first the lower, then the upper switch housing screws to 35-45 in-lbs (4- 5.4 Nm) . 5 3 1 1 4 2 2 is00735 1. Switch housing screws 2. Grooves 3. Handlebar clamp 4. Left handlebar grip 5. Larger flange Figure 1. Left Handlebar Switch Housing REMOVE AND INSTALL THE RIGHT GRIP NOTE Right handlebar switch removal requires a Service Manual for your model and year of motorcycle. A Service Manual can be purchased from your Harley-Davidson Dealer. 1. Refer to the RIGHT HANDLEBAR SWITCH section of the Service Manual for removal of the switch housing assembly. This is necessary to access the throttle cables. 2. Refer to the THROTTLE CONTROL section of the Service Manual to disconnect the throttle cables and remove the existing right grip/throttle sleeve assembly. After removal, make sure that the handlebar end is clean and smooth. 3. Follow instructions in the Service Manual to install the new right grip/throttle sleeve to the handlebar and connect the throttle cables. 4. Verify that the right grip/throttle sleeve rotates and returns freely and does not bind on the handlebar or switch housing.

Incoming search terms:

Victory V92SC Sport Cruiser COMFORT SPORT HANDLEBAR REMOVAL AND INSTALLATION

0

Filed Under (Victory) by admin on 13-11-2010

download
1. Remove wiring harness dart clips. 2. Disconnect clutch switch connector. 3. Remove 2screwsforclutch lever bracket clamp, remove clutch lever bracket from handlebar. 4. Remove screws for left handlebar switch assembly. Disconnect fast idle cable from lever. Remove switch assembly. 5. Grasp left grip end firmly. While twisting grip end back&forth, pull grip end off and discard. 6. Remove left grip by insertingathin screwdriver between the grip and handlebar end. Spray as mall amount of water/soap solution into the area between the grip and handlebar end. Aggressively twist the grip back-and-forth while simultaneously pulling the grip off. 1. Locate accessory handlebar. 2. Clean inside of throttle grip assembly and throttle cable flange grooves. Ill. 1. 3. Clean throttle grip area. Ill. 1. 4. Slide throttle assembly onto right handlebar end (cableshavenot been removed and should still be attached to the throttle tube). 5. Position the handlebar over the top of the triple clamp and reinstall using bolts removed instep 10. of handlebar removal. Torque to 30 ft. lbs. 6. Install right handlebar switch housing onto handlebar. NOTE: Make sure that locating pin of switch assembly aligns with hole in handlebars. 7. Install right handlebar switch housing screws, make sure locating pin properly aligns with hole in handlebar. Tighten screws to specified torque. 8. Install master cylinder and clamp, install screws. 9. Torque screws to specification. 10. Connect front brake switch wiring harness. 11. Install fast idle cable onto fast idle lever. 12. Clean inside of left grip and handlebar grip surfaces

HARLEY DAVIDSON CHROME HANDLEBAR CLAMP BOLT KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
INSTALLATION Improperly aligned handlebars can contact the fuel tank when turned to the left or right. Contact with the fuel tank can cause cosmetic damage. (00372a) NOTES Check that the handlebar is centered on the risers. To make sure that the handlebar is centered, verify that the knurled areas on the outboard side of each riser are equal. Slowly turn the front wheel to the full right fork stop and then the full left fork stop to be sure the handlebar does not contact the fuel tank. If contact with the fuel tank occurs or the handlebars are not properly centered, see Figure 1. Slightly loosen the four upper clamp screws, and center the handlebar or raise the handlebar angle as necessary until proper clearance is obtained, then temporarily snug the screws, but do not fully tighten. 4 1 2 3 4 is00868 1. Upper clamp 2. Screw (4) 3. Handlebar 4. Handlebar risers (2) Figure 1. Handlebar Clamp Hardware 1. Remove and discard screws (2) that fasten upper clamps (1) to handlebar risers (4). Save washers under screw head for later use. 2. For Kit 94453-04: Select new chrome screws from the kit that match the length of the screws removed. For all other Kits: Select new chrome screws from the kit. 3. Slide washers previously removed onto screws, and thread screws through the upper clamps into risers. -J03586 1 of 2 4. If handlebar adjustments were made, snug screws but do not fully tighten. a. The bottom surfaces of upper clamps are offset, creating a gap between the clamp and riser on one side. b. Tighten clamps so the gaps appear to the rear of the handlebar, then tighten screw to 12-15 ft-lbs (16.3- 20.3 Nm). 5. If handlebar adjustments were not made, tighten screws to 12-15 ft-lbs (16.3-20.3 Nm). SERVICE PARTS

HARLEY DAVIDSON SLOTTED HANDLEBAR RISER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 02-02-2011

download
INSTALLATION NOTE Cover the fuel tank with a clean shop towel to prevent scratching. Damage to the finish could result. 1. Remove the two hex head cap screws and split lock- washers on the underside of the upper fork bracket that hold the currently installed risers in place. Discard the screws, but retain the lockwashers for re-assembly. Retain all additional hardware components that become dislodged from the riser when the screws are removed. 2. Remove and discard the four screws that fasten the currently installed handlebar upper clamp(s) to the risers. Remove and discard the clamp(s). Remove the handlebar from the risers, and carefully allow the handlebar to rest on the fuel tank. 3. Obtain the new slotted risers (1) and hex head cap screws (2) from the kit, and the split lockwashers and hardware components removed in Step 1. NOTE The upper cup washer (A) must be oriented with the flat side up , and the lower cup washer (D) with the flat side down . The ground wire (G) and internal tooth lockwasher (H) are mounted to the right-side riser. 4. Refer to Figure 1 for the correct orientation and reassembly sequence. Install the new risers onto the upper fork bracket using the saved hardware and new screws. Snug the riser screws, but do not fully tighten at this time. 5. Center the handlebar on the risers. To make sure that the handlebar is centered, verify that the knurled areas on the outboard side of each riser are equal. 6. Position the new handlebar upper clamps (3) from the kit, and install with new hex socket head screws (4). Snug the upper screws, but do not fully tighten. Improperly aligned handlebars can contact the fuel tank when turned to the left or right. Contact with the fuel tank can cause cosmetic damage. (00372a) 7. Slowly turn the front wheel to the full right fork stop and then the full left fork stop to be sure the handlebar does not contact the fuel tank. If contact occurs and the handlebars are properly centered, raise the handlebar angle as necessary until proper clearance is attained. 8. Tighten the upper handlebar-clamp screws as follows: a. Tighten the front screws to 12-15 ft-lbs (16-20 Nm) . b. Tighten the rear screws to 12-15 ft-lbs (16-20 Nm) . c. Tighten the front screws to 12-15 ft-lbs (16-20 Nm) . NOTE The gap between the upper clamps and the risers should be equal at the front and rear of the handlebar after tightening. 9. One at a time, remove the riser bolts installed in Step 4. Apply two drops of Loctite® 271 (Red) to the bolt threads and re-install. Tighten the riser bolts to 50-60 ft-lbs (68-81 Nm)

Incoming search terms:

HARLEY DAVIDSON HANDLEBAR GRIPS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 30-01-2011

download
INSTALLATION Remove and Install the Left Grip 1. See Figure 1. Remove the two screws with flat washers securing the handlebar clamp (3) to the clutch lever bracket. Remove the clamp and position the clutch hand lever assembly away from the handlebar. 2. Loosen, but do not remove, the upper and lower switch housing screws (1). 3. Remove the end cap from the existing left handlebar grip if equipped. Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. Do not lubricate left handlebar grip before installation. Lubricating grip can cause it to come off while riding, which could result in loss of control and death or serious injury. (00315a) NOTE Make sure that the handlebar surface and the inside of the grip are smooth, dry and thoroughly cleaned of all dirt or adhesive residue. 4. Position the new left grip (4) so the larger flange (5) is at the bottom. Push the grip fully onto the handlebar. 5. Fit the grooves (2) on the outboard side of the upper and lower switch housing over the flanges on the end of the grip, then loosely fasten the two screws. 6. Position the clutch hand lever assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the bottom of the clutch lever bracket. 7. Align the holes in the handlebar clamp with those in the clutch lever bracket, and loosely fasten the two screws with flat washers. Adjust the switch housing and clutch hand control position for rider comfort. 8. Tighten first the upper, then the lower handlebar clamp screws to 60-80 in-lb (6.8-9 Nm) . 9. Tighten first the lower, then the upper switch housing screws to 35-45 in-lb (4-5.4 Nm)

Honda TRX 400EX INSTALLATION And REMOVAL INSTRUCTIONS

0

Filed Under (Honda) by admin on 14-12-2011

download
Quiet cores are supplied with this kit but not installed. To install the quiet cores remove both rear end caps ((turn downs) and install the quiet cores with the tubes facing inward. Re-install the end caps. REMOVAL Remove seat, disconnect attery and remove. Remove front fenders and side skirts. Remove fuel tank (make sure to shut fuel off and drain remaining fuel in the line before removing). Remove stock muffler first, then remove stock headers. Retain the 4 stock header bolts to install on your new exhaust system. Remove the rear bolt from your stock air box. Loosen stock intake clamp at carburetor. Remove stock boost bottle from the side of the boot. Loosen stock snorkel clamp at the air box, remove stock retaining clip at the front of the snorkel. Remove stock air box, intake boot and snorkel together from the ATV. Slide tarter solenoid off of stock mounting prongs. Remove Phillips screws from fuse holder and remove from plastic housing. Remove plastic battery housing from the ATV. Unplug tail light from harness. Unclip harness from the 2 clips above the battery. CARBURATION Now would be a good time to replace your stock main jet, with the supplied 190 main jet and replace your stock pilot jet with the supplied 48 pilot jet. Make certain that all hoses are tight and routed as stock. Be certain carb clamp is tight when re-installed. INTAKE BOOT Remove the intake boot from the stock air box. Take an exacto knife or razor blade and trim off the rubber piece that the hard plastic snorkel slips into. Trim around the intake boot staying the same distance as the rest of the lip. Take a hax saw and cut the groove as the rest of the boot is, being
careful not to cut all the way through (Picture Fig.2).

Incoming search terms:

HARLEY DAVIDSON "LIVE TO RIDE" HANDLEBAR GRIPS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
installation Do not lubricate the left grip of handlebar in any way before installation. This could allow grip to come off while riding which could result in loss of control of vehicle and death or serious injury. 1. Remove existing left handlebar grip by carefully cutting it away from the handlebar using a sharp blade or knife. Remove right grip/throttle sleeve assembly following instructions in appropriate Service Manual. After removal, make sure that left and right handlebar ends are clean and smooth. 2. Check that end caps are securely fastened to grips. Tighten screw inside grip to secure end caps. 3. Assemble new throttle sleeve to handlebar. Refer to appropriate Service Manual for detailed procedure. NOTE Surfaces to be glued must be clean, dry, and free from oil. If surfaces are not clean, dry, and free from oil, then the new application may not adhere as desired. Please observe the following WARNINGS when using the adhesive contained in this kit. FLAMMABLE, INJURIOUS TO EYES, HARMFUL IF SWALLOWED, VAPOR HARMFUL. FLAMMABLE: CONTAINS METHYL ETHYL KETONE. Use only in well ventilated areas. Avoid contact with eyes, mucous membranes, and prolonged skin contact. KEEP OUT OF REACH OF CHILDREN. If swallowed, do not induce vomiting. Call a physician immediately. This product contains a chemical(s) known to the State of California to cause cancer, birth defects or other reproductive harm. 4. Liberally apply a coating of Harley-Davidson Adhesive (Part No. 99839-95) to the inside of left handlebar grip using the cotton swab. Make sure adhesive fully covers all inside surface area of the grip. Also, apply a coat of adhesive to the handlebar end. 5. Check how the rectangular pattern is oriented on the throttle (right) grip. Align pattern on left grip to match right grip and immediately push the new grip completely onto handlebar end. 6. Rotate the end caps so the “Live to Ride”text is positioned at the top of both grips. NOTE Do not hesitate when installing left grip or adhesive will dry before installation is complete. Allow 6-8 hours at 70°F to achieve full cure of the adhesive. Prior to starting engine, verify that the throttle control will snap back to the idle position when released. A throttle control that prevents the engine from automatically returning to idle can lead to a loss of control of vehicle which could result in death or serious injury. Cleaning

HARLEY DAVIDSON SPORTSTER HAND GRIPS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
Remove and Install the Left Grip 1. See Figure 1. Using a T27 TORX®drive head, remove the two screws with flat washers securing the handlebar clamp (3) to the clutch lever bracket. Remove the clamp and position the clutch hand lever assembly away from the handlebar. 2. Using a T25 TORX®drive head, loosen but do not remove the upper and lower switch housing screws (1). 3. Remove the end cap from the existing left handlebar grip if so equipped. Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. Do not lubricate left handlebar grip before installation. Lubricating grip can cause it to come off while riding, which could result in loss of control and death or serious injury. (00315a) NOTE Make sure that the handlebar surface and the inside of the grip are smooth, dry and thoroughly cleaned of all dirt or adhesive residue. 4. Position the new left grip (4) so the larger flange (5) is at the bottom. Push the grip fully onto the handlebar. 5. Fit the grooves (2) on the outboard side of the upper and lower switch housing over the flanges on the end of the grip, then loosely fasten the two screws. 6. Position the clutch hand lever assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the bottom of the clutch lever bracket. 7. Align the holes in the handlebar clamp with those in the clutch lever bracket, and loosely fasten the two screws with flat washers. Adjust the switch housing and clutch hand control position for rider comfort. 8. Using a T27 TORX®drive head, tighten first the upper, then the lower handlebar clamp screws to 60-80 in-lbs (6.8-9.0 Nm). 9. Using a T25 TORX®drive head, tighten first the lower, then the upper switch housing screws to 35-45 in-lbs (4.0-5.1 Nm). Remove and Install the Right Grip 1. Refer to the RIGHTHANDLEBARSWITCH section of the service manual for removal of the switch housing assembly. This is necessary to access the throttle cables. 2. Refer to the THROTTLECONTROL section of the service manual to disconnect the throttle cables and remove the existing right grip/throttle sleeve assembly. After removal, make sure that the handlebar end is clean and smooth. 3. Follow instructions in the service manual to install the new right grip/throttle sleeve to the handlebar and connect the throttle cables. 4. Verify that the right grip/throttle sleeve rotates and returns freely and does not bind on the handlebar or switch housing.

Steering Stem Nut Installation Instructions & Owners Manual

0

Filed Under (Tips and Review) by admin on 26-11-2010

download
Sport Bike Damper Kit Installation Instructions DISCLAIMER: All GPR Sport Bike damper kits are manufactured to be used ONLY w/ the stock top triple clamp and frame. If either is modded, aftermarket or crash damaged, the kit will not install properly and GPR will not be held responsible for the consequences of improper installation due to this or any other improper mounting or modifying. The provided instructions must be followed precisely, as failure to do so can result in the GPR damper kit being installed incorrectly. An improper installation may lead to a variety of undesirable steering problems. Please take your time and carefully follow the installation instructions. As always, give us a call if you have any questions, we’re more than happy to assist you in getting the damper kit mounted on your bike properly 1. Remove the stock Steering Stem Nut (SSN) and washer from the stock top triple clamp steering stem. Carefully set the stock nut aside, as you may be using it later. Bikes requiring a specific GPR SSN to replace the stock SSN are listed at the end of this installation sheet. If your bike is on the chart, throw you stock SSN in the toolbox along w/ the washer, as you may need it at a later date if for any reason you need to remove the GPR kit from your bike. Stock SSN’s that are either ‘domed’ at the top or ‘flanged’ at the bottom will definitely NOT work, may lead to problems and should NOT be reinstalled during the baseplate installation. See #2 below for further instructions about both SSN/Steering stem and arm clearance issues 2. With the stock SSN and washer removed, place the GPR Baseplate over the steering stem on the top triple clamp and reinstall either the stock SSN or the GPR SSN provided. Torque SSN down to the recommended specs as per the owner’s manual for your particular bikes make and model. NEVER reinstall the stock washer that came on the bike! The baseplate is now your new washer. If you do accidentally use the stock washer, the arm on the stabilizer will most likely ‘rub’ on the nut. It will be too high, potentially locking the steering and handlebars, thus making your bike un steerable and unridable. DO NOT ride your bike until all installation steps have been completed and you can visually verify that there is clearance between the arm of the stabilizer and the steering stem and/or SSN. Once the installation is complete, at the #1 setting you

Incoming search terms:

2000-2010 KTM X2 SWITCH WIRING HARNESS Removal and Installation Manual

0

Filed Under (KTM) by admin on 25-01-2012

download
The included 3600-SWHA switch harness is intended for use with offroad models that do not come with a Hi/Low beam switch from the factory. The harness is compatable with stock AC lighting electrical systems as well as high output DC electrical systems. 1. Remove the stock numberplate or headlight. Remove the stock kill switch from handlebars and replace with the 3600-SWHA switch. 2. Remove the gas tank. Route the white and black leads from the 3600-SWHA under the tank following the wires from the stock kill switch. Disconnect the stock kill switch bullet and connect the white wire of the 3600-SWHA to the wiring harness. Disconnect the stock kill switch ring terminal and connect the ring terminal of the 3600-SWHA. Fully remove the stock kill switch. Be sure all the wires are safe from being burned or pinched and re-install the gas tank. 3. Disconnect the two female spade terminals from the stock headlight switch (if present). Connect the terminal with the yellow wire to the red power lead from the switch. Connect the white wire to the blue accessory output from the switch. Be sure the clear silicone sleeves are covering the stock plastic housings. 4. Connect the X2 headlight to the switch headlight plug. Note: The stock headlight plug will not be used for the X2 installation, but is still functional for connecting the stock headlight. The stock plug will turn on and off with the new headlight switch, and will be powered in either of the Low or High Beam positions

Incoming search terms:

Incoming search terms: