super nut industrial co ltd mail

You search Auto repair manual PDF super nut industrial co ltd mail, if there are search results will appear below. If search results do not exist, please search by others keyword.





KTM 990 SUPER DUKE 950 SUPERMOTO 950 SUPER ENDURO REPAIR MANUAL

0

Filed Under (KTM) by admin on 22-11-2010

download
Adjusting the position of the compression and rebound damping Rebound damping: -Turn in the adjusting screw 1 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Compression damping, low speed: -Turn in the adjusting screw 2 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Compression damping, high speed: -Turn in the adjusting screw 3 in a clockwise direction all the way to the stop. -Turn back the respective number of clicks in a counterclockwise direction. Adjusting the spring preload NOTE: the spring preload is the difference between the unloaded and preloaded length of the spring. -Tighten the adjusting nut 4 with the special tool T106 until you have the prescribed spring preload. -Tighten the lock screw on the adjusting nut Disassembling the shock absorber -Write down the spring preload. -Write down the rebound and compression damping settings, counting the clicks or number of turns while turning in a clockwise direction. -Unscrew all of the adjusting screws in a counterclockwise direction. -Clamp the upper part of the shock absorber in a vise as shown in the photo, using protective jaws. -Loosen the lock screw 1 (AH 4 mm), loosen the adjusting nut 2 using the special tool T106 3 and relieve the spring. NOTE: mark the position of the lock screw. -Press the spring down with the special tool T101S and pull out the spring retainer 4 . -Remove the washers 5 and spring 6 . 4-2 Repair manual WP Shock absorber 990 Super Duke, 950 Supermoto, 950

Incoming search terms:

HARLEY DAVIDSON REAR AXLE-NUT COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
REAR AXLE-NUT COVER KIT GENERAL Kit Number 41704-09, 41705-09, 41706-09 Models For model fitment information, please see the P&A Retail Catalog or the Parts and Accessories section (English only). Additional Parts Required The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references Service Manual information. A Service Manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. Kit Contents See Figure 1 and Table 1. INSTALLATION NOTES The shorter axle-nut cover mounts to the right side of the motorcycle. Axles that have been removed for service, replacement or repair may have been assembled in reverse orientation from their stock design. Axle-nut covers may not fit properly on reversed axles. Refer to the appropriate Service Manual for correct axle orientation. 1. Adjust the position of the exhaust system (if necessary) to provide axle-nut clearance. 2. Position each axle-nut cover over the appropriate axle nut. 3. The skull version nut covers have two set screws per cover. Position the logo and snug up one set screw to hold in place and the other to prevent rotation. 4. Tighten the axle-nut cover set screws to 70 in-lb (7.9 Nm) . NOTE The set screws in this kit are treated with a thread-locking compound. When replacing or re-installing the set screws (2), apply Loctite® 243 (Blue) Threadlocker and Sealant (Harley- Davidson Part Number 99642-97) to the set screw threads. SERVICE PARTS

Incoming search terms:

1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

HARLEY DAVIDSON DYNA CUSTOM SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
WO-UP SEAT INSTALLATION Currently Installed Seat Removal NOTE When performing the following procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs. 1. Remove currently installed seat following the instructions in the Owner’s Manual. 2. If a two-up seat WAS installed: Proceed to Step 6, Grab Strap Installation . If a solo seat WAS installed: See Figure 1. Remove the Bar & Shield hole plug (11) from the rear seat mounting hole (1)Seat mounting hole, rear 2. Fender hole, center 3. Seat mounting hole, front 4. Grab strap mounting hole 5. Wire routing hole (reference) 6. Fender hole, front (reference) 7. Hardware location for two-up seat 8. Hardware location for solo seat 9. Seat retention nut 10. Retention washer 11. Hole plug, Bar & Shield 12. Hole plug, plain Figure 1. Fender Hole Identification and Hardware Locations 3. At the front seat mounting hole (3), remove the retention washer (10) from the seat retention nut (9). From the underside of the fender, remove the seat retention nut from the vehicle. Insert the Bar & Shield hole plug into the front seat mounting hole. 4. See Figure 2. Obtain the cable strap (3) from the kit. a. Place the retention nut (1) over the cable strap (3) so that the wide end of the nut rests on the eye of the cable strap. b. Thread the cable strap up under the fender and through the rearmost seat mounting hole. c. Pull up on the cable strap to hold the nut snug against the underside of the fender. d. With the rib on the retention nut seated into the notch in the fender hole, slide the retention washer (2) into place from the rear (this will lock the retention nut in place), then remove the cable strap. 3 2 1 is01955 1. Retention nut 2. Retention washer 3. Cable strap (installation aid) Figure 2. Retention Nut Installation Grab Strap Installation 5. If a two-up seat WAS installed: Remove the existing grab strap and all attaching hardware, then proceed to Step 6. If a solo seat WAS installed: Proceed to Step 6. 6. See Figure 5. Obtain the new grab strap (8), hex head screw (9), plastic retention nut (10), washer (11) and hex nut (12) from the kit. 7. From the underside of the fender, insert the screw up through the grab strap mounting hole and secure with the plastic retention nut.

HARLEY DAVIDSON DYNA PASSENGER PILLION SEAT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 05-03-2011

download
REMOVE SEAT NOTE When performing the following installation procedures, avoid scratching painted surfaces (fender, tank, etc.) with tools or metal seat tabs. 1. Remove screw to detach rear seat mounting bracket from fender. 2. Remove two capscrews that attach seat mounting bracket to bottom of stock seat. 3. Remove the existing seat from the motorcycle. Save the seat bracket and mounting screws for installation of the new seat. 4. If motorcycle has a grabstrap installed, remove nut and washer that holds passenger strap in place and remove strap. 5. See Figure 1. Remove the plastic cap from rearmost fender hole (3). 6. Remove the seat retention nut and washer from the solo seat mounting hole. 7. See Figure 2. A cable strap may be used as an installation aid to remove and reinstall the retention nut and washer. Place the retention nut (1) over the cable strap (3) so the wide end of the nut rests on the eye of the cable strap. Thread the cable strap up under the fender and through the rearmost fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. 8. With the rib on the retention nut seated into the notch in the fender hole, slide the retention washer (2) into place from the rear. This will lock the retention nut in place. Remove the cable strap. 2 5 1 2 1 3 6 7 4 is00363 1. Retention nut and washer (2-up seat positon) 2. Retention nut and washer (solo seat position) 3. Rear-most fender hole 4. Middle fender hole 5. Grabstrap mounting hole 6. Flange screw 7. Plastic retention nut

HARLEY DAVIDSON COMFORT PROFILE REAR SADDLEBAG GUARD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-03-2011

download
REMOVAL 1. Remove saddlebags from motorcycle following the instructions in the service manual. 2. See Figure 3. Remove grab strap screw and washer (G). Remove grab strap (H). Remove seat following the instructions in the service manual. 3. Remove left and right side covers (located in front of saddlebags) by removing screw from bottom of side cover. Save hardware and side covers for final assembly. 4. Support muffler assembly with a block of wood or other suitable method. For FLTR and FLHX Models 1. See Figure 3. Remove the screws (F) securing saddlebag guards to muffler supports. 2. Remove bolt (M) and nut (P). Save bolt (M) for installation. Discard nut (P). 3. Remove screws (B and C) and nut (E). Save screws (B and C) for installation. Discard nut (E). 4. Remove stud receptacle (I) and save for installation. 5. See Figure 1. Remove antenna bracket (1), mounting fasteners (2), antenna mounting nut (5), washer (4) and antenna adapter (3). Save the antenna and hardware, discard the bracket. 6. Remove support (D) and discard. 7. Repeat Steps 1 through 4 for other side. For FLHTCU and FLHTC Models 1. Remove and discard screws (X) and guard rail mounts (W and V). 2. Remove screw (Q) and rear guards (U). Discard rear guard assembly including screws (T) and clamps (R and S). Discard screw (Q). 3. Remove and discard screw (K) and nut (L). 4. Remove screws (N and C) and nut (E). Save screw (C) for installation. Discard nut (E), screw (N) and forward guard. 5. Repeat Steps 1 through 5 for other side. For All Other Models 1. Remove screws (N and C) and nut (E). Save screw (C) for installation. Discard nut (E) and screw (N). 2. Remove and discard screw (K) and nut (L). 3. Remove forward guard and discard. 4. Repeat for other side

Incoming search terms:

HONDA GL1800 TIMING CHAIN COVER INSPECTION NUT INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 28-02-2011

download
GL1800 TIMING CHAIN COVER INSPECTION NUT 1. Place bike on center stand. 2. Remove the inspection nut on the bike using a 17mm socket. 3. Remove the rubber o-ring seal from the inspection nut and place on new inspection nut. 4. Install the new inspection nut using the 17mm socket.

HARLEY DAVIDSON XL SOLO CUSTOM SEAT KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
INSTALLATION 1. Refer to the Owner’s Manual and follow the instructions given to remove the seat. 1 2 4 1 3 is03341 1. Stock retention nut and washer 2. Plastic cap 3. Rearward fender hole 4. Center fender hole Figure 1. Retention Nut and Plastic Cap Location 2. For models that had a solo seat: Proceed to Step 3. For models that had a 2-up seat: The retention nut and washer must be moved from the rearward mounting hole to the center fender hole where the rear seat bracket will be attached. Use a cable strap to aid in this step as fol- lows: a. See Figure 1. Remove retention nut from rearward fender hole (3) and plastic cap (2) from center fender hole (4). b. Install plastic cap into the rearward fender hole. c. See Figure 2. Place the retention nut over the cable strap so the wide end of the nut rests on the eye of the cable strap. Thread the cable strap up under the fender and through the center fender hole. Pull up on the cable strap to hold the nut snug against the underside of the fender. d. With the rib of the retention nut seated into the notch in the fender hole, slide the retention washer into place from the rear. This will lock the retention nut in place. 3. Position the solo seat on the motorcycle frame with the mounting bracket at the rear. Bring the seat forward and engage the tab on the seat into the slot at the base of the fuel tank. 4. See Figure 3. Secure the seat to the fender using the knurled knob (3) and neoprene washer (4) from the kit. Install the washer on the knob and tighten the knob securely to the fender seat nut

1999 Ducati 900 Super Sport Carbon Fiber INSTALLATION MANUAL

0

Filed Under (Ducati) by admin on 25-10-2010

download
I. Stock muffler removal: refer to diagram #1 *All hardware removed in this procedure must be saved for reinstallation. See Figure 2* 1. Loosen the Allen bolt holding the exhaust bracket to the rear foot peg mount. (It may be easier to turn the nut first then the Allen bolt) 2. Remove the nut and then support the muffler while removing the Allen bolt. Be careful not to loose the washer since it will now just drop out. 3. Now slide the spacer from the foot peg support and remove the muffler by sliding it straight out of the header. 4. Now remove the two rubber bushings and put aside so they won’t fall out and become lost. 5. Repeat the procedure for the other muffler. Parts you will need to reuse. x2 Diagram 1 I. Forza installation: refer to diagram #2 1. Determine the left muffler from the right. The Forza sticker faces out and the inlet pipes bend in slightly. See figure 3. 2. Slide the muffler onto its respective header pipe. 3. Replace the two rubber bushings in the foot peg mounts. 4. Slide the muffler clamp over the muffler and align with the bushings. 5. Squeeze the muffler clamp by hand and insert the spacer first: through both holes in the clamp and second: through both bushings. The clamp should be on the outside of the foot peg support (see diagram2). 6. Install the washer then the nut and snug the nut leaving it loose enough to allow muffler to rotate in the clamp. 7. Turn the pipe until the exhaust tip is pointed down. Then check that the muffler clears the swing arm. 8. Repeat the procedure for the other side.

1996-2003 KAWASAKI ZX7R INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) It is mandatory to use blue Loc-tite on all bolts. We promise they will come loose if you don’t. 2) Remove the large nut and washer that holds your triple clamp on. Install the new nut that we provide which has HEX drive facing UP. You will NOT use the stock washer. 3) Torque the new nut to your factory recommended setting as they vary. Normally a minimum of 50-80 ft lbs. 4) Install the new triple clamp damper mount (TC mount) over the new triple clamp nut with the “machined register” (the small knub) indexing into the matching groove on the top, back of your stock triple clamp. The knub insures the mount cannot spin should the damper try to loosen the main nut. 5) Be sure this TC mount is setting down flush on the triple clamp surface all the way around. This part is machined precisely to fit over the Scotts triple clamp nut. The groove machined into the nut is positioned so once the set screws are tightened, it will suck the TC mount down against your triple clamp. Remove any obstructions that would not allow the TC mount to sit flush against your stock triple clamp surface. 6) Tip to save time: Before installation, using Loc-tite start all the setscrews first, until flush with the inside bore. 7) Using blue loc-tite on the setscrews, run them all in against the nut equally and then proceed to tighten each one making your way around until they are all equally tight. They should be checked after the first ride as normally they will settle into the groove in the nut and require tightening. 8) (Note: You must use some heat to compromise the Loc-tite before trying to remove the setscrews or the small Allen head setscrews can be stripped easily). 9) Remove the two, stock-front tank retaining bolts. You will replace these with longer ones in the kit. 10) Install the new “frame bracket tower”. There is a front and back to this part, note the picture! 11) Install the longer tank bolts supplied, through our frame bracket and into your tank mounting holes. 12) Grease the tower pin and drop it in the tower pin hole. It is designed to “float” and requires no retaining devices. Keep the tower pin and hole portion greased lightly. 13) Install the damper using the (2) 6×20 Allens. The link arm slot aligns with the flats on the tower pin. 14) Read your damper manual for initial settings on the controls. The damper is infinitely adjustable and totally up to the user to find their preference. Start with softer (counter clockwise) settings. Normally where we set the unit is a good starting point, usually 8 clicks out on the base valve. 15) The base valve controls the immediate feel of damping forces exerted

Incoming search terms: