suzuki raider 150 front double disc break

You search Auto repair manual PDF suzuki raider 150 front double disc break, if there are search results will appear below. If search results do not exist, please search by others keyword.



  suzuki raider 150 front double disc break Direct Download speed 5282 Kb/s

  suzuki raider 150 front double disc break Full Version speed 6162 Kb/s



HARLEY DAVIDSON FRONT THUNDERSTAR WHEELS INSTALLATION

0

Filed Under (Harley Davidson) by admin on 08-11-2010

download
Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. -J04065 1 of 8 For FXSTD Models: Discard the tapered r ight side wheel spacer. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTE • For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771- 07, 43609-07, 44323-07, 44282-07, 44322-07, 43975-07, 43602-07 and 43773-07 install short valve stem (43157- 83A) included in the installation kit. • For Kits 40943-09, 40966-09 and 40996-09 install long valve stem (43206-01) included in the installation kit. 2. See Figure 2. Install valve stem assembly (L, M or N) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771-07, 43609-07, 40943-09, 40966-09 and 40996-09: • The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and/or DOT markings to identify it as the brake disc and primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44323-07, 44322-07 and 44282-07: • Install the wheel so that the hub markings are on the left side of the motorcycle. The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and hub markings to identify it as the primary bearing side. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). • The gross axle weight ratings is unaffected by the installation of this wheel on a vehicle equipped with a 21-inch wheel. For Kits 43975-07, 43773-07, and 43602-07: • The wheel has a machined groove (item 5, Figure 2) in the hub face to identify the right side. • For 2007 and later FX Softail Models and 2008 and later FXDWG: The left side of the wheel is the primary bearing side. For all other models the right side of the wheel is the primary bearing side. • For Kit 43602-07: An arrow is engraved into the right side hub to indicate the direction of rotation. • For Kits 43975-07 and 43773-07: An arrow is cast between the spokes on the right side to indicate the direction of rotation. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake-disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). 4. Install wheel assembly parts from the appropriate Service Parts table for this fitment and stock brake disc. Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in Service Manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in installation kit. For FXSTD Models: Install wheel kit, stock left wheel spacer and right side wheel spacer from installation kit in place of the tapered right side wheel spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install the left side wheel spacer provided in the kit between the stock left wheel spacer and the left fork. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual

Incoming search terms:

Dazon Raider Classic 150 (Oil-cooled & Internal Gearbox): Service Manual (single/ double-seat)

0

Filed Under (Dazon) by admin on 30-11-2010

download
1.2.1 Fuel Please use the gasoline of SAE 90# or above. Also we recommend you to use the unleaded gasoline. 1.2.2 Engine Oil Please use the high-quality engine oil of SAE 10w/30SF. 1.3 Break-in Procedure For your first 2 hours of riding, don’t exceed 2/3 throttles. Vary the engine speed for the first 5 hours. Never hold the engine at full throttle for long periods of time. Raider-Classic 150 (Oil-cooled&Internal Gearbox): Service Manual (single/ double-seat) EEC Version;3.0 Feb..2005 5 1.4 Specifications DIMENSIONS SINGLE-SEAT / DOUBLE-SEAT Overall Length 2330mm / 2300mm Overall Width 1310mm / 1460mm Overall Height 1425mm / 1425mm Wheelbase 1475mm / 1520mm Ground Clearance 200mm VIN Accord with GMVR A01-01 Statutory Plate& Safety Labels Accord with GB 7258-1997 ENGINE Model DZ1P57QMJ Type Oil-cooled, single cylinder, 4-Stroke Engine Capacity 150cc Displacement 149.6ml Bore X Stroke 57.4mm X 57.8mm Max Power 7.0kw or 7000r/m Max Torque 10.0N.m or 6500 r/m Idle Speed 1700 ± 100 r/m CO Emission 7.0g/km HC Emission 1.0g/km Fuel Type SAE 90# or above (unleaded) Lubricate Oil Type SAE 10W/30SF Lubrication Force & Splash Cooling Oil-cooled Ignition C. D. I. Starting Electric Spark Plug C7HSA (NGK) Spark Plug Gap 0.6~0.7mm Transmission Chain Transmission Gearbox Transmission Ratio F.:7.8:1 ; B.:11.297:1 Compression Ratio 9.5 ± 0.1 : 1 Carburetor MIKUNI BS 24-1005 Absorber Normal (in 10 5 times of experiments) CAPACITIES Front/ Rear Tire Load Coefficient 36 Front/ Rear Tire Speed Level L Fuel Tank 7.0L, 130kpa (no leakage in experiments) Engine Oil 1000ml Gear Oil 200ml Starting Time ≤15s Climbing ≥20%

Incoming search terms:

Vespa GTS Super Specification

0

Filed Under (Vespa) by admin on 11-11-2010

download
Gts super 300 ie Gts super 125 ie s 125cc s 50cc Gts 250 ie Gts 125cc LX 125cc LX 50cc 2 stroke Engine Single-cylinder, catalised, QUASAR 4 stroke, 4 valve electronic injection Single-cylinder LEADER 4 stroke with electronic injection Single-cylinder LEADER 4 stroke Single-cylinder HI-PER 2 stroke Single-cylinder, catalised, QUASAR 4 stroke, 4 valve electronic injection Single-cylinder, catalised, LEADER 4 stroke, 4 valve Single-cylinder LEADER 4 stroke Single-cylinder HI-PER 2 stroke Capacity 278cc 124cc 124cc 50cc 249cc 124cc 124cc 49cc Power 16.4 kW / 7500 rpm 10.5 Kw / 9500 rpm 7.65 Kw / 8250 rpm 3.2 Kw / 7500 rpm 15.7 Kw / 8500 rpm 7.65 Kw / 8250 rpm 7.65 Kw / 8250 rpm 2.5 Kw / 8500 rpm Max Torque 22Nm / 6500 rpm 12 Nm / 8000rpm 9.6 Nm / 7250 rpm 4.4 Nm / 6500 rpm 20.1 Nm / 6500 rpm 9.6 Nm / 7250 rpm 9.6 Nm / 7250 rpm 3.3 Nm / 6500 rpm Cooling Liquid Liquid Forced Air Forced Air Liquid Liquid Forced Air Forced Air Starter Electric Electric Electric and kick starter Electric and kick starter Electric Electric Electric and kick starter Electric and kick starter Transmission Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Automatic twist and go Front Suspension Single arm, dual chamber hydraulic shock absorber with coaxial spring Single arm link with coil spring and double hydraulic shock absorber Single arm link with coil spring and double hydraulic shock absorber Single arm link with coil spring and double hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Single sided trailing link with hydraulic shock absorber Rear Suspension Two dual effect shock absorbers with adjustable preload Coil spring and double hydraulic shock absorber Coil spring and double hydraulic shock absorber Coil spring and double hydraulic shock absorber Twin hydraulic shock absorbers with preload adjuster Twin hydraulic shock absorbers with preload adjuster Hydraulic shock absorbers with preload adjuster Hydraulic shock absorber Front Brake ø 220mm disc brake 220mm disc brake ø 200mm disc brake ø 200mm disc brake ø 220mm disc brake ø 220mm disc brake ø 200mm disc brake ø 200mm disc brake Rear Brake ø 220mm disc brake 220mm disc brake ø 110mm drum brake ø 110mm drum brake ø 220mm disc brake ø 220mm disc brake ø 110mm drum brake ø 110mm drum brake Front Tyre Tubeless 120/70-12″ Tubeless 120/70 – 12″ Tubeless 110/70 – 11″ Tubeless 110/70 – 11″ Tubeless 120/70-12″ Tubeless 120/70-12″ Tubeless 110/70 – 11″ Tubeless 110/70-11″ Rear Tyre Tubeless 130/70-12″ Tubeless 130/70 – 12″ Tubeless 120/70 – 10″ Tubeless 120/70 – 10″ Tubeless 130/70-12″ Tubeless 130/70-12″ Tubeless 120/70 – 10″ Tubeless 120/70-10″ Running weight 158kg 158kg 114kg 96kg 151kg 145kg 114kg 96kg Length/Width/Height 2230mm / 755mm / 1170mm 1930mm / 755mm / 1930mm 1770mm / 740mm / 1140mm 1755mm / 740mm / 1140mm 1930mm / 755mm / 1170 mm 1940mm / 755mm / 1180 mm 1770mm / 740mm / 1140mm 1755mm / 740mm / 1140mm Fuel Tank Capacity 9 litres 9 litres 8.5 litres 8.5 litres 9.2 litres 10 litres 8.5 litres 8.5 litres Emmissions Euro 3 Euro 3 Euro 3 Euro 2 Euro 3 Euro 3 Euro 3 Euro 2 Colours Rosso Dragon Nero Lucido Montebianco Rosso Dragon Nero Lucido Montebianco Taormina Nero Lucido Montebianco Taormina Nero Lucido Montebianco Marrone Terra Di Toscana Bronzo Perseo Nero Vulcano Blu Midnight

Incoming search terms:

1994-2003 Suzuki GSXR750 and 1997-2004 Suzuki GSXR600 Superbike Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 10-01-2011

download
Step 1: Identify the key components that complete our Superbike kit: You should have 2 lines (front kit), 1 double banjo bolt and 2 lower adapters. There are also a total of 7 washers. 5 will be used, and 2 are spares. We strongly suggest having a professional mechanic install these brake lines; all other installations VOID warranty. Inspect your brake system after every race. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: Uninstall stock hoses; be aware of how the stock system was routed in case you need to re-install it. Step 4: Install the Galfer adapters onto the right and left calipers. Thread each adapter into the calipers with one washer, and torque at 12 to 13 ft pounds. (See picture S4) Step 5: Install the right and left lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt (see picture S5) is included to run two lines down. The positioning sequence on the master cylinder is as follows: Master cylinder, washer, straight banjo (from right line), washer, 12-degree banjo (from left line), washer, and double banjo hex. Double banjo bolt torque level is 12 FT Pounds. ( See picture S6) Make sure that the 90-degree fittings on each caliper are pointing away from the bike just a little bit (see pictures S7 through S9 of calipers) . Thread each banjo end into the adapter, and torque to 6 ½ Ft pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions. Once the lines have been checked for clearance, we recommend using a zip-tie to bring the lines together about an inch above the lower triple clamp area. (Picture S10) Step 6: Bleed brake system according to owner’s manual, and build appropriate pressure. Finishing with DOT 4-brake fluid is recommended.

Incoming search terms:

Toyota Camry L4 – 2.4L 2004 Brakes and Traction Control Disc Brake System Service and Repair

0

Filed Under (Toyota Manuals) by admin on 24-05-2011

Download
REMOVE FRONT DISC BRAKE CYLINDER SLIDE BUSH 10. Remove the cylinder slide bush from the cylinder slide pin.
a. REMOVE FRONT DISC BRAKE BUSH DUST BOOT 11. Remove the 2 bush dust boots from the disc brake cylinder mounting. a. REMOVE FRONT DISC BRAKE CYLINDER MOUNTING LH 12. Remove the 2 bolts and disc brake cylinder mounting LH. a. REMOVE CYLINDER BOOT 13. Using a screwdriver, remove the set ring and cylinder boot.
a. REMOVE FRONT DISC BRAKE PISTON 14. Place a piece of cloth or similar, between the piston and the disc brake cylinder. a. Use compressed air to remove the piston from the disc brake cylinder. CAUTION: Do not place
your fingers in front of the piston when using compressed air. NOTICE: Do not spatter the brake fluid

HARLEY DAVIDSON DUAL DISC FRONT BRAKE KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
This kit is designed for installation on the following models which have original equipment 39mm front fork tubes (including chromed tubes) and 19-in. cast-aluminum front wheels: • 2000 – 2003 XLH 883, XLH 883 Hugger and XLH 1200 • 2000 – 2003 FXD (Super Glide) This kit can also be installed on the above XLH and FXD models which have original equipment 39mm front fork tubes and 19-in. laced front wheels only after one of the following procedures is performed: • The original single-flange hub of the 19-in laced front wheel is replaced with a new double-flange hub (H-D Part No. 43629-00), (sold separately) which will accept the second brake disc. OR • The original 19-in. laced front wheel assembly, which has a single-flange hub, is replaced with a new 19-in. laced front wheel assembly (H-D Part No. 43579-00), (sold separately) which has a double-flange hub designed to accept the second brake disc. See the Service Parts Illustration for a list of the contents included in this kit. This kit does not include the front brake line required for a dual disc system; the brake line must be purchased separately as follows: • For XLH 883 motorcycle equipped with low-rise (flat) handlebars, order dual disc brake line H-D Part No. 45148-96. • For XLH 883 Hugger, XLH 1200, and FXD Super Glide models with “buckhorn” (pull-back) handlebars, order dual disc brake line H-D Part No. 45111-96. The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) Brakes are a critical safety component. Contact a Harley- Davidson dealer for brake repair or replacement. Improperly serviced brakes can adversely affect brake performance, which could result in death or serious injury. (00054a) Removal and Disassembly – Front Brake System NOTE A Service Manual for your motorcycle is available at your Harley-Davidson Dealer. 1. Block motorcycle underneath frame so that front wheel is raised off the ground slightly. 2. Remove original front brake caliper from left side of front fork according to appropriate Service Manual procedures. Let caliper hang loose on brake line. Save all components and fasteners for reinstallation. NOTE Do not operate the front brake lever with the front caliper removed because the piston may be forced from the caliper. Reseating the piston requires disassembly of the caliper . 3. Remove socket head screw which secures a clamp (retains front brake line) to underside of front fork lower bracket (lower triple clamp). Discard clamp and screw. 4. Remove screw, lockwasher, and clamp which secure front brake line to right rear side of front fork upper bracket (upper triple clamp). Save all components for reinstallation. 5. Remove right mirror and, if applicable, right turn signal lamp assembly from original front brake master cylinder casting. Save all components and fasteners for reinstalla- tion.

Incoming search terms:

HARLEY DAVIDSON FRONT BRAKE DISC LOCK INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-03-2011

download
INSTALLATION Do not operate vehicle with brake disc lock in place. Operation with lock on disc will restrict movement of the wheel, which could result in death or serious injury. (00457b) NOTE Insert key all the way to the bottom of the cylinder. Turn key clockwise 180 degrees to the open position. DO NOT FORCE KEY! Key should turn freely. If key does not freely rotate, try turning key slightly left and right while inserting to align disks inside cylinder. Failure to insert key all the way to the bottom of cylinder could cause key to jam. For Models with Hydraulic Fork Front Ends 1. See Figure 1. Insert reminder cord (3) into slot on disc lock (1). 2 1 3 is 01599 1. Lock 2. Caliper 3. Reminder cord Figure 1. Installing Disc Lock 2. Slide lock (1) over front brake disc as close to rearward edge of brake caliper (2) as possible. Push button completely down to lock. 3. Roll motorcycle forward slowly until lock gently contacts caliper. 4. See Figure 3. After installing disc lock, place loop end (1) of reminder cord (2) over handlebar grip. For Models with Springer Front Ends 1. See Figure 2. Insert reminder cord (5) into slot on disc lock

HARLEY DAVIDSON FRONT TYPHOON WHEELS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-03-2011

download
If installing kit 44615-08, 40774-10, 44657-08 or 43300053 on a Dyna model with stock laced wheels, the separate purchase of stock brake disc (44553-06A) or polished brake disc (41500012) is required. The following Harley-Davidson Genuine Motor Accessories are recommended for proper maintenance and cleaning: •Harley® Bright™ Chrome Cleaner (94683-99) •Harley® Glaze™ Polish and Sealant (99701-84) •Harley®Wheel and Spoke Brush (43078-99) •Harley-Davidson®Wheel and Tire Cleaner (94658-98) •Harley® Preserve™ Bare Aluminum Protectant (99845-07) Touch-up paint for painted wheels is available from a Harley- Davidson dealer: •Touch-Up pen, wheel, black (94482) The rider’s safety depends upon the correct installation of this kit. Use the appropriate service manual procedures. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00333a) NOTE This instruction sheet references service manual information. A service manual for your model motorcycle is required for this installation and is available from a Harley-Davidson Dealer. 1 2 is06470 1. Closed brake disc 2. Open brake disc or floating rotor Figure 1. Front Brake Disc Styles Table 1. Front Disc Hardware Fitment Hardware Brake Disc 5 Stock disc screws (3655A) Closed disc Chrome screw kit (46646-05) includes 5 screws 5 Stock disc screws (3762M) and 5 disc washers (6966M) Open disc NOTE: Models equipped with dual front brakes and models being equipped with a wheel with dual brake mounting surfaces require twice as many screws/washers (10 total screws or 2 chrome screw kits if available). INSTALLATION NOTE Use plastic protectors on tire mounting tools and rim clamps when mounting a tire to a painted wheel. For wide low profile tires a tire mounting machine with a second arm to press down on the sidewall while the wheel is rotating is recommended.

2011 FORD HARLEY-DAVIDSON F-150 TECHNICAL SPECIFICATIONS

0

Filed Under (Harley Davidson) by admin on 01-11-2010

download
Final assembly location Dearborn Truck Plant, Dearborn, Mich. POWERTRAIN AND CHASSIS ENGINE Type 6.2-liter two-valve V8 Configuration Iron block, aluminum heads Valvetrain SOHC, two valves per cylinder, roller-rocker shaft with hydraulic lash adjusters Bore x stroke 4.02 x 3.74 inches Displacement 379 cubic inches, 6,210 cc Compression ratio 9.8:1 Horsepower 411 hp @ 5,500 rpm Torque 434 lb.-ft. @ 4,500 rpm Fuel Injection Sequential multi-port electronic Oil capacity Seven quarts DRIVETRAIN Layout RWD or AWD TRANSMISSION Standard Six-speed automatic overdrive Gear ratios 1st 4.17:1 2nd 2.34:1 3rd 1.52:1 4th 1.14:1 5th 0.86:1 6th 0.69:1 Reverse 3.40:1 Available axle ratios 3.73 SUSPENSION Front 4×2 Coil-on-shock, long-spindle double-wishbone independent, stamped-steel lower control arm (sport-tuned) Front 4×4 Coil-on-shock, long-spindle double-wishbone independent, stamped-steel lower control arm (sport-tuned) Rear 4×2 Hotchkiss-type non-independent live, leaf springs and outboard shock absorbers (sport-tuned) Rear 4×4 Hotchkiss-type non-independent live, leaf springs and outboard shock absorbers (sport-tuned) STEERING Type Power rack-and-pinion Turning circle curb-to-curb 47.0 feet 2011 FORD HARLEY-DAVIDSON F-150 TECHNICAL SPECIFICATIONS BRAKES Front 13.8-inch vented disc Rear 13.7-inch vented disc Assist type Vacuum, RSC WHEELS AND TIRES Wheels 22-inch polished forged aluminum with painted accents with “Harley- Davidson” Bar & Shield logo on wheel ornament Tires P275/45R-22 all-season BSW DIMENSIONS (inches unless otherwise noted) EXTERIOR SuperCrew RWD SuperCrew AWD Wheelbase 144.5 144.5 Vehicle length 231.9 231.9 Vehicle width (without mirrors) 79.2 79.2 Vehicle height 74.8 75.9 Track width, front/rear 67.0/67.0 67.0/67.0 Cargo box length 67.0 67.0 Width (max) between wheels 50.0 50.0 Inside box height 22.4 22.4 INTERIOR Seating capacity Five Five Headroom Front row 41.0 41.0 Rear row 40.3 40.3 Legroom Front row 41.4 41.4 Second row 43.5 43.5 Shoulder room Front row 65.9 65.9 Second row 65.5 65.5 Hip room Front row 60.5 60.5 Second row 64.6 64.6 WEIGHTS AND TOWING (pounds)

Incoming search terms:

2008 SUZUKI GSXR1300 Hayabusa Front Brake Line Kit INSTALLATION INSTRUCTIONS

0

Filed Under (Suzuki) by admin on 09-01-2011

download
Step 1: Identify the key components that complete our brake line kit: You should have two (2) hoses, one (1) double banjo bolt, and two (2) single banjo bolts. There are also a total of nine (9) washers. Seven (7) will be used, and two (2) are spares. We strongly suggest having a professional mechanic install these brake lines, and all other installations void warranty. Step 2: To ensure no paint damage from a brake fluid spill, completely cover the front end of the bike. This process is messy, and brake fluid WILL drip! Step 3: After drying out the OEM brake system, uninstall stock hoses. Take note of how the stock system was routed in case you need to re-install it. Please note there is a plastic shield on the lower triple clamp of your machine; we took this piece off to ease installation. Remove the OEM hose holder, and keep the bolt for later use. (See picture C) Step 4: Install the right and left (to your right and left as you sit on the bike) lines to the calipers, using the shorter line on the right side. These lines will travel from the master cylinder to the calipers; a double banjo bolt is included to run two lines down. The positioning sequence on the master cylinder is as follows: Double banjo hex, washer, straight banjo labeled for right line, washer, 12-degree banjo labeled for left line, washer, master cylinder. Please see picture A for reference! Double banjo bolts must be torqued at 12 FT pounds. Step 5: Route both brake lines through the enclosed c-clip, and attach to the lower triple clamp using the bolt from the OEM holder. (See picture B) Drop the lines down and thread the single banjo bolts at each caliper using the following sequence: single banjo hex, washer, 20-degree banjo, washer, thread into caliper. Torque banjo bolts to 12 FT pounds. Before you proceed to the next step, please check for clearance of the lines. Compress the front end to make sure that the lines are not binding with anything. When the front end is fully extended or fully compressed, double check that the lines are traveling correctly and clear from any obstructions

Incoming search terms: