teryx 4 wirering

You search Auto repair manual PDF teryx 4 wirering, if there are search results will appear below. If search results do not exist, please search by others keyword.



  teryx 4 wirering Direct Download speed 5282 Kb/s

  teryx 4 wirering Full Version speed 6162 Kb/s



Kawasaki Teryx Skid Plate Installation And Removal Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Let skid sit in sun or inside house at room temperature for a couple hours. Cold weather can shrink plastic slightly but this is not an issue once installed. 2. Remove Stock Teryx Hardware/skids and set aside hardware to use on new skid 3. You have a couple options in mounting the new skids. 1) remove stock metal engine inspection cover underneath Teryx, or 2) using UHMW skid as template cut out hole in inspection cover (A below) to allow access to oil filter. Cut hole substantially larger than skid hole so as not to cut yourself when removing/installing oil filter 5. Fasten all main skid bolts and washers, but do not tighten all the way so that you are able to move skid slightly to center all bolt holes. 6. Fasten all front and rear skid bolts and washers, but do not tighten all the way so that you are able to move skid slightly to center all bolt holes. . Once skids are in desired location tighten all bolts 9. You will be required to drill 2 – 3/16 pilot holes in the 2 rear most main skid mounting locations. Use the supplied self tapping bolts and washers to attach skid in these locations

2008-2009 KAWASAKI TERYX HEADLAMPS HIDTERYX HID KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
a. Remove rubber boot from the back of the headlamp housing assembly. b. Push down on metal latch and pull away from lip to release halogen bulb. Pull out halogen bulb. c. Insert HID bulb, line up bulb to fit into the bulb holder, lower latch to lock bulb in place. d. Replace Rubber boot on the back headlamp assembly. (Make sure to pull wires through the center of the rubber boot first before you start to pull down boot on the back of the headlamp assembly.) e. Make sure that the wiring, coming from the HID bulb, clears the black plastic housing that encases the headlamp assembly so connection from the bulb to the ballast is possible. If installed correctly there is no need for drilling or modifications of any type. 2. Ballast a. Mount ballast in location of your choice – recommended near the headlight. 3. Wiring Note: DO NOT modify the wiring that runs from the HID bulb to the ballast. It will cause the system to work improperly. It will void the warranty . a. Once ballast is installed connect corresponding wires from HID bulb to corresponding male / female plugs on ballast. b. To connect wiring from ballast to Teryx primary system i. Find wire extension with white triangular head with black, yellow & green wires at opposite end ii. Connect black off extension to black wire coming off ballast iii. Connect Yellow / Green wire to red wire coming off ballast iv. Connect triangular head to corresponding plug on Teryx Factory Wiring End

KAWASAKI TERYX 750 CLUTCH KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove both seats from the vehicle. Next, remove the passenger side lower body panel. There is a mixture of Philips head screws and also plastic push pin fasteners that have to be removed. 2. With the side panel off, the next item to remove is the plastic housing over the engine. These are all “push in” style plastic clips that hold it in place. Once all the pins are out, you can slide the housing off and set it aside. 3. Now the lower long plastic panel under the seat has to be removed (again mainly plastic push clips to remove) . Once they are all out, carefully remove and set aside. 4. Next, remove the fuel tank. Remove the two lines on the top of the tank. There are two straps that hold the tank in place. Remove the bolt from each strap, remove the straps, and lift the fuel tank out. 5. Now the bracket that holds the fuel pump on has to be removed. There are two bolts here to take out. Once this is done, mark the two wires to the coil and disconnect them. Set the bracket out of the way . 6. Next, the clutch cover bolts can be removed and the norkel on the housing can be loosened and i Teryx 750 Clutch Kit Instructions 5/1/09 removed. Take the clutch cove off and set out of the way. 7. With the clutch visible, you can remove the secondary clutch with a large impact wrench and metric socket . 8. Remove the bolt from the primary clutch. This is a left hand thread on the bolt. Next you will need a Kawasaki drive clutch puller (part #352251) to pop the clutch loose. If you do not have a puller, the spring cap can be removed on the vehicle and the weights can be changed out in there as well. 9. With the clutches sitting on the bench, remove the bolts that hold on the spring cover. Remove the stock spring and the stock weights 10. After reading the directions on the new weights, add the correct amount of weight to each clutch weight and install them in the clutch. Place the weight to the left side in the clutch pocket and then install the aluminum spacer. Repeat this process for the other three weights. 11. Install the new spring supplied in the kit and install the spring cover, paying close attention to the arrows on the cover. 12. Next, remove the stock spring from the secondary. It is recommended that you use the TEAM Compression tool (part # 930001) for this. With the clutch on the compression tool, compress the spring retainer down far enough to remove the snap ring with the needle-nose pliers . Slowly back off the t-handle and remove the tool.

Kawasaki Teryx Bowkaddy Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
The most effective method of mounting Bowkaddy on a Kawasaki Teryx is with the use of Kaddy Bracket UTV. However, one small after-market modification is necessary to make the bracket fit the rear roll bars on these side by side vehicles. Two additional 21/64″ holes must be drilled in the bracket at the locations shown in the image below. For more product and installation information,

Kawasaki Teryx Electric Steering Installation Manual

0

Filed Under (Kawasaki) by admin on 29-04-2012

download
installation Instructions for Kawasaki Teryx 1. Before installation, center steering wheel and verify tires are straight. 2. Begin by removing all Phillips screws retaining the plastic hood to the front grill, headlights, and frame structure and remove front clip assembly. 3. Remove plastic shroud by removing the 4 phillips screws that retain it to the frame. 4. There are 2 bolts that hold the steering column tube in place and you need to reach up under frame work to get to them. They are 14 mm and you need a box and open end wrench to access them. Loosen the upper one and remove the lower one. Remove the pinch bolt at the column shaft and u-joint. Remove the lower pinch bolt at the rack and u-joint and while tilting the column up and down remove the stock steering shaft.
5. Once the shaft is removed, you are ready for installation. Your bracket and motor has come completely assembled as shown below. You will need to remove the lower shaft from the motor to install it. After removal of the shaft you will need to loosen the 3 mounting bolts from the bracket to the motor to allow clearance for the bracket to slide over the frame piece where it will mount

Kawasaki Teryx Fuel Gauge Kit Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
You will now proceed to drill the hole using a 1″ Hole saw similar to the one shown. Fig 2 As you drill the hole you will periodically check to see how deep you’ve gone, the goal is to cut as close as possible but not go all the way through. It helps to blow away the loose bits of material before you pull the saw back to check. Fig 3 You will want to carefully remove all loose bits of plastic from the cut channel. Once finished it should look like this before proceeding. Fig 4 Now insert a T handle wrench into the hole to keep the plug from falling in as shown, a screwdriver will work as well. Use a box cutter to finish the cut and pop the plug out using the T handle.
Black Rhino Performance Page 3 of 4 Fig 5 Once you have made the cut all around the plug will pop out. Now is a good time to check and make sure that you didn’t drop a bunch of cuttings in the tank. If you were careful there shouldn’t be anything in there. Fig 6 Now that that is finished it is time to install the sender. First you will want to coat both sides of the cork gasket with a petroleum resistant gasket sealant. The pattern of the holes is not symmetrical so make sure the holes on the sender line up with the gasket. Fig 7 Finish the installation by hand tightening the screws and just tight enough without forcing the gasket out from under the sender. Let the cork do its work, over tightening can cause leaks. Fig 8 When finished, it’s a good idea to silicone the contacts of the sender. This helps to prevent shorting or damaging the sender or gauge.

KAWASAKI TERYX POWERFLOW INSTALLATION PROCEDURE

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Remove the airbox and clean thoroughly. 2. Cut off the factory plastic ring on airbox. DO NOT cut a bigger than 3″ 5/8 diameter (See figure #1) 3. After cutting hole in airbox place billet adapter inside the airbox and insert hole then mark the mounting holes for the billet adapter. 4. Drill the marked locations with a 7/32 drill bit. 2. Install the billet adapter from the inside of the airbox with the Trinity Racing logo at the top of the airbox. Insert the bolts and washers from the carburetor side of the airbox and then secure it with blue loctite then tighten bolts. 3. Install Outerwear over new filter. 5. Install the filter onto the billet adapter and make sure the rubber neck of the air filter is completely free of oil. Tighten the filter clamp securely, but do not over tighten and cut into the rubber neck of the filter. 6. Reinstall the air box assemble with lid ( if you choose to reinstall the airbox lid ) onto the vehicle. Be sure to tighten and double-check all the nuts and bolts you have installed. 7. Check your vehicles jetting. Depending on your modifications and riding altitude, a jetting change may be required for your ATV to run properly.

KAWASAKI TERYX EFI Installation Instructions.

0

Filed Under (Kawasaki) by admin on 08-02-2011

download
Basic Tuning Adjustments 1. The following instructions are for basic fuel tuning. Modes 1,2, & 3 are allowing adjustments to increase and decrease the amount of fuel the engine needs. Modes 4 & 5 are for advanced tuning only. DO NOT change modes 4 & 5 when doing basic tuning! 2. To help understand how these modes work, you can think of them as if you were working with a carburetor. 3. Remember each time you push the MODE button you will be advancing to the next mode. Push the MODE button once and you are now in mode 1, push the MODE button again and you are now in mode 2 and so on. You only need to be concerned with modes 1, 2 & 3 for basic tuning. Modes 4 & 5 are for advanced tuning ONLY. 4. If you need to go back to the settings that were pre programmed when you purchased the controller, just look at the picture in each mode, the colored square represents where the settings were when you purchased the controller. 5. Looking at the controller you will see eight lights with numbers under them, this is what you need to look at when changing settings. The #1 light on the controller represents the leanest setting. TRINITY RACING DOES NOT TAKE REPONSIBLITY FOR DAMAGES THAT MAY OCCUR DURING OPERATION OF YOUR VEHICLE UNDER IMPROPER JET SETTINGS. IT IS THE FINAL RESPONSIBLITY OF THE OWNER/RIDER TO ADJUST JETTING TO SPECIFIC RIDING CONDITIONS AND ELEVATION BEFORE RIDING. WARNING! 1.877.FAS TOYS 2.Remove both seats 6. Re-install engine cover and seats. 6. Mode 1 green light represents idle & cruise adjustment (i.e. pilot jet). To adjust this setting push the MODE button once and then push the plus or minus buttons to adjust fuel as needed. 7. Mode 2 yellow light represents an additional amount of fuel added during acceleration (i.e. needle position). To adjust this setting, push MODE twice and then push the plus or minus buttons to adjust fuel as needed. 12 34 56 7 8 12 34 56 7 8 8. Mode 3 red light represents more fuel being added during full throttle (i.e. main jet). To adjust this setting push the MODE button three times and then push the plus or minus buttons to adjust fuel as needed. 9. If you are confident about your tuning skills and feel you need to adjust other parameters, see Advanced Tuning. 12 34 56 7 8 Advanced Tuning Adjustments 1. Advance tuning has two modes in which to adjust. They are called mode 4 and mode 5. In basic tuning, you are changing the amount of fuel that the engine receives, but with advance tuning, you will be changing when the fuel will be available. In each mode you can adjust how soon the fuel delivery occurs. 2. Mode 4 yellow light and blue light represent when the fuel delivery is available during partial throttle acceleration. To adjust this setting, push the MODE button four times and then push the plus or minus buttons to adjust fuel as needed. Only the yellow light will be changing.

Incoming search terms:

Kawasaki Teryx Roof Installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1. Place Roof Panel on top of UTV Roll cage and center front to back, and left to right. 2. Using Figures 1 Below – place UTV Roof Mounting Brackets on Roof and using a marker, mark the position of the holes needed for each Roof Mounting bracket . For rear of roof mounting, use existing slotted bracket and mark one hole through the factory slotted brackets as shown in Figure 2. Figure 1
Copyright 2007 DiamondBack Automotive Accessories, Inc. Page 3 Figure 2 3. Next, remove the roof from the roll cage and using a drill with 1/4″ bit, drill holes using the marks as a guide. 4. Cut (4) 3″ strips of adhesive foam and apply to roof in between holes to prevent roof rattling once mounted. Foam should run in the direction of the roll cage as shown in Figure 1 above. 5. Next, reposition the roof on the roll cage according to step 1. 6. Prior to attaching the roof mount brackets, cut the remaining adhesive foam in half and apply one section to the roof in the center of the roof where roof and each roll cage bar meet as shown in Figure 1 above. If additional tape is required to prevent rattling it can be purchased from any hardware store as window sealant foam tape. 7. Next, attach the roof mount brackets according to Figure 3. Use channel locks or pliers to hold top of carriage bolt and turn nut with 7/16″ socket.

Kawasaki Teryx 750 Cab Enclosure Kit Installation And Removal Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Remove seats and set aside for better access to vehicle interior. Refer to Owner’s Manual for instructions. ii) Remove lower foot guardrails and set shoulder screws aside for later use. Loosen 19mm bolts ( A in Fig.1) until 3/16″ gap can be achieved. iii) Loosely fasten rubber stops ( B in Fig.1) to Hinge Mounting Brackets using 6mm bolts. Mount brackets to vehicle as shown in Fig.1 and hand tighten 19mm bolts. iv) Align lower bracket hole to existing foot guard mounting hole and fasten with OEM shoulder screw ( C in Fig.1). NOTE : Apply pressure to screwdriver in order catch threads on nuts. v) Adjust upper edge of brackets with mallet to make bracket edge flush to roll bar edge (Fig.2). Tighten 19mm bolts. Adjust and tighten rubber mounts. FLUSH A B Fig.2 Fig.1 2. Rear Bracketery i) Remove 14mm bolts from lower mounting points on rear crossbar. Install Striker Mounting Brackets as shown (Fig.3). Reinstall bolts and hand tighten only . Attach Striker Plates using (4) ¼-20 x 3/8″ screws, keep loose for later adjustment. ii) Remove 14mm bolts from upper crossbar and install Upper Rear Panel Brackets as shown (Fig.4). Tighten 14mm bolts back into place. 3. Panel Installation i) Install low density foam to interior of panels as shown (Fig.5.) Approx. (8) 3″ long strip are required on each side panel. Install low density foam to entire door / panel interface. ii) Mount side panels to roll cage and temporarily clamp to top roll bar. Loosely insert remaining (2) shoulder screws to each foot well. Adjust each panel to obtain proper alignment at front, top and lower rear. iii) Ensure hinge mounting bracket edges are flush with inside door frame and transfer hinge bolt hole locations onto plastic panels. Remove panels and drill holes using ¼” bit. Re-install panels and shoulder screws onto vehicle. iv) Mount hinges as shown (Fig.6) with (8) ¼-20 x 5/8″ Lg. Flat Head screws. DO NOT OVER TIGHTEN