tmx 155 cooler

You search Auto repair manual PDF tmx 155 cooler, if there are search results will appear below. If search results do not exist, please search by others keyword.



  tmx 155 cooler Direct Download speed 5282 Kb/s

  tmx 155 cooler Full Version speed 6162 Kb/s



HARLEY DAVIDSON SOFTAIL OIL COOLER KIT WITH CHROME OIL COOLER COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
INSTALLATION 1. See Figure 1. Install the oil cooler (2) to the frame with three clamps (4), three socket head screws (1), three nuts (5) and six washers (3) from the kit. Orient the clamps flat side forward and on the forward side of the oil cooler. Tighten the three oil cooler mounting screws to 96-120 in- lbs (10.9-13.5 Nm) . 2. See Figure 2. Remove the spin-on oil filter and oil filter adapter (1) from oil filter mount location. Clean the oil filter mounting area thoroughly. Discard oil filter and adapter. 1 3 4 4 4 3 5 2 is03387 1. Socket head screw (3) 2. Oil cooler 3. Washer (6) 4. Clamp (3) 5. Locknut (3) Figure 1. Oil Cooler Clamp Installation NOTE The oil cooler adapter assembly has two flanges protruding out of the back side. The flanges must be installed toward the oil filter mounting location and through the oil adapter gasket. 3. See Figure 3. From the kit, install the oil cooler adapter gasket (3) onto the oil cooler adapter assembly (1). The oil cooler adapter assembly flanges should be aligned so it is installed into the oil adapter cooler gasket cutout as shown. NOTE Due to the locating flanges, the oil cooler adapter assembly and gasket will only install properly in one position on the oil filter mounting surface. 4. See Figure 3. Install the oil cooler adapter assembly and gasket onto the oil filter mounting surface of the engine with the mounting fitting (2). Ensure adapter locates properly in the mounting surface. Ensure the raised lip of the mounting fitting faces the adapter assembly. Tighten mounting fitting to 12-16 ft-lbs (16.3-21.7 Nm) .NOTE Slide hose clamps from the kit onto the hoses prior to installa- tion. 1 2 is00754 1. Oil filter adapter 2. Oil filter seal surface Figure 2. Stock Filter Mounting Adapter 1 2 3 is00761 1. Oil cooler adapter assembly 2. Mounting fitting 3. Oil cooler adapter gasket Figure 3. Install Oil Adapter 5. See Figure 5. Obtain the left side cooler hose (4) and right side cooler hose (5) from kit. Follow the markings on hoses to connect onto the oil cooler and oil cooler adapter, as shown. 6. Fasten hoses to oil cooler adapter and oil cooler with worm drive clamps (6). Tighten clamps to 8.0 in-lbs (0.9 Nm) . 7. Lubricate a new oil filter’s seal with new engine oil. Thread filter on until seal touches mounting surface, then turn an additional 1/2 to 3/4 turn. NOTE Position the clamps to avoid interference with oil filter installation. Check that hose routing is clear of the oil filter and sharp edges. The hoses must be free of bends or kinks that could obstruct oil flow. 8. Ensure all cables and harnesses are clear of the oil cooler adapter, in order to prevent wear. 9. Thoroughly clean the oil cooler of all dirt, grease and wax with isopropyl alcohol. Use the alcohol to clean the chrome oil cooler cover as needed. Allow to dry. is00745 Figure 4. Apply Sealant Inside Chrome Cover 10. See Figure 4. Apply sealant to the inside of the chrome cover as shown, at the upper and lower corners. NOTES Be careful to avoid getting sealant on the oil cooler cooling fins. Do not operate the motorcycle for 24 hours to allow the sealant to fully cure. 11. Slip the cover over the oil cooler. Remove any excess sealant from the front and back of the oil cooler. Hold the cover firmly in place for one minute. System Flow Test 2005 & Later Models or Models with Later Style Dipsticks Oil level cannot be accurately measured on a cold engine. For pre-ride inspection, with motorcycle leaning on jiffy stand on level ground, oil should register on dipstick between arrows when engine is cold. Do not add oil to bring the level to the FULL mark on a COLD engine. (00185a) 2004 & Earlier Models

Incoming search terms:

HARLEY DAVIDSON CHROME OIL COOLER COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION 6 2 1 3 5 4 is04287a 1. Oil Cooler 2. Guard 3. Stock Washer 4. Stock Nut 5. Mounting Bracket 6. Area to Apply Heat Figure 1. Oil Cooler Preparation Be sure to follow manufacturer’s instructions when using the Robinair Heat Gun or any other radiant heating device. Failure to follow manufacturer’s instructions can cause a fire, which could result in death or serious injury. (00379a) 1. See Figure 1. Remove the oil cooler guard (2) from the oil cooler (1) by using the Heat Gun (or equivalent) to apply heat to the top surface. Pull the guard away from the oil cooler and discard. 2. Remove and discard the three locknuts (4) and flat washers (3) fastening the oil cooler to the mounting bracket (5). 3. Raise the oil cooler slightly to separate the studs on the underside of the oil cooler from the mounting bracket. 4. See Figure 2. Place the oil cooler cover (1) onto the oil cooler studs, between the oil cooler and the mounting bracket. 5. Lower the oil cooler and cover into the holes in the mounting bracket. 6. Place a new flat washer and locknut from the kit onto each stud. Line the oil cooler cover up squarely against the oil cooler, and tighten the locknuts to 80-100 in-lbs (9.1-12.4 Nm) . SERVICE PARTS

YAMAHA ROAD STAR WARRIOR OIL COOLER KIT INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 09-11-2010

download
INSTALLATION: 1. See FIG. F: Apply a thin film of oil to O-RING (#9) on OIL COOLER MOUNT ADAPTER (#2). Install the OIL COOLER MOUNT ADAPTER with OIL COOLER SUMP STUD (#6). Note that o-ring on adapter is mounted against oil filter sump. TIP: Only tighten “finger tight” at this point so adapter can move as needed to adjust oil lines. 2. See FIG. G: Install OIL LINES (#3 & #4) to OIL COOLER and OIL COOLER MOUNT ADAPTER as shown. Do not tighten fittings yet. NOTE: The shorter 9-3/4″ OIL LINE will be on the TOP fitting on the ADAPTER. 3. See FIG. H :Install OIL COOLER to frame with the BILLET OIL COOLER CLAMP (#7). Adjust OIL COOLER to desired position and tighten the three 10-24 X 1/2 SOCKET HEAD SCREWS (#8) securely. Rotate the OIL COOLER MOUNT ADAPTER as necessary to align the Oil Lines properly. WARNING: Make sure OIL COOLER is moved outward far enough so that it does not contact the Front Fender when the fender goes through its full range of motion! 5. See FIG. I & J: Tighten the AN fittings on the OIL COOLER MOUNT ADAPTER as shown with an 11/16″ open end wrench. Tighten the AN fittings on the OIL COOLER with an 11/16″ open end wrench. TIP: To prevent the OIL COOLER from turning when the fittings are tightened, place a thin screw driver or long allen wrench between the fittings as shown. NOTE: DO NOT USE ANY SEALANT ON AN FITTINGS! 6. See FIG. K : Tighten OIL COOLER SUMP STUD (#6). Re-install oil filter. Start the engine and check for leaks. Check oil level and top-off as necessary. MAINTENANCE:

HARLEY DAVIDSON XL PREMIUM OIL COOLER KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Refer to Owners Manual to drain engine oil and remove oil filter. 2. See Figure 1. Remove oil feed hose (1) from oil pump. 3. Remove oil feed hose fitting from engine crankcase. Discard oil feed hose. INSTALLATION 1. See Figure 2 and Table 1. Apply Hylomar Gasket and Thread Sealant to threads of fitting (1) and install fitting to oil pump. 2. Apply Hylomar Gasket and Thread Sealant to threads of fitting (1) and install fitting to crankcase. 3. Tighten fittings to 55-65 in-lbs (6.2-7.4 Nm) . 1 2 3 1 is04015 1. Fitting 2. Oil Hose Cooler Supply 3. Oil Hose Cooler Return Figure 2. Oil Hose Cooler Return and Supply Assmeblies 4. Loosely install oil cooler return hose assembly (3) to crankcase fitting. 5. Loosely install oil cooler supply hose assembly (2) to oil pump fitting. 6. See Figure 3 for proper oil hose routing. The oil supply hose (1) should be the upper hose and the oil return hose (2) the lower hose 1 2 is04018 1. Oil Supply Hose 2. Oil Return Hose Figure 3. Oil Cooler Hose Routing 7. Remove two existing clips holding the clutch cable and wire harness from the left frame downtube. 8. See Figure 4 and Table 1. Position oil cooler clamps (7) in approximately the same position as the clips that were removed from the frame downtube. 9. Loosely attach oil cooler (4) to the clamps (7) using screws (9) and nuts (8). 10. Attach oil return hose (3) to the inboard connection of oil cooler (4) with worm clamp (5).

HARLEY DAVIDSON TOURING OIL COOLER KIT AND CHROME OIL COOLER COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 20-02-2011

download
INSTALLATION 1. See Figure 1. Remove the spin-on oil filter (2) and oil filter adapter (1) from oil filter mount location. Clean the oil filter mounting area thoroughly. Discard oil filter adapter. NOTE The oil adapter assembly has two flanges protruding out of the back. The flanges must be installed toward the oil filter mounting location and through the oil adapter gasket. 2. See Figure 2. Install the oil adapter gasket (3) onto the oil filter adapter assembly (1). The oil adapter assembly flanges should be aligned so they are installed into the oil adapter gasket cutout as shown. 1 2 is00602 1. Oil filter adapter 2. Oil filter Figure 1. Oil Filter and Adapter 1 2 3 5 4 is00761a 1. Oil cooler adapter assembly 2. Mounting fitting 3. Oil cooler adapter gasket 4. Gasket adhesive side 5. Oil cooler adapter assembly gasket surface Figure 2. Install Oil Adapter

BMW Motorcycle R1100 RT R1100 RS R850/ 1100 GS R850/ 1100R Repair Manual

0

Filed Under (BMW) by admin on 18-11-2010

download
Engine Connection Nm Nm Oil filter Oil filter 11 11 Oil drain plug 32 32 Oil pump Mesh filter basket to engine block 9 9 Oil pump cover 9 9 Pressure relief valve 35 35 Oil pressure switch 30 30 Oil cooler Oil cooler pipe to engine block 10 10 Cooling oil line – banjo screw 25 25 Cooling oil line – banjo screw with oil vent valve 25 25 Oil lines to oil cooler 25 – Oil cooler to holder 9 9 Oil cooler return line to engine block 35 35 Oil cooler feed line to frame 20 20 Oil cooler feed line to engine block 25 25 Screw-in union for oil cooler connection at engine block 35 35 Clean threads and apply Loctite 603 to inner and outer threads and in the contact face area Oil cooler hose at oil thermostat – 40 Cylinders Tightening sequence M 8 screw 20 20 M 6 screw 9 9 Chain guide rail pivot screw 18 18 Timing chain Chain tensioner 32 32 Connecting rod Big end cap Joint torque 20 20 Additional wrench angle 80° Crankcase Tightening sequence: M 10 screw (oiled) 45 45 M 8 screw (oiled) 20 20 M 6 screw Engine electrical system Connection Nm Nm Starter motor to engine 20 20 Starter cover to gearbox housing 7 – Positive lead to starter motor 10 10 Alternator to alternator support cover 20 20 Tensioning and retaining strap at alternator 20 20 Spacer at alternator 20 20 Positive lead to alternator 15 15 Belt pulley at alternator 50 50 Belt pulley to crankshaft 50 50 Poly-V belt preload 8 8 Spark plug 20 20 13 Fuel preparation and control Temperature sensor on engine block 25 25 16 Fuel tank and lines Fuel tank to rear frame 22 22 Fuel pump assembly to tank 6 6 18 Exhaust system Muffler to footrest 35 35 Manifold to cylinder head (with strap) 22 22 (with jacket pipe) 18 18 Muffler to support plate for center stand 20 20 Clip on muffler 50 50 Grease clamping face with Never Seez Oxygen sensor (lambda probe) to muffler 55 55 Grease with Never Seez

NACA Oil Cooler Inlet Installaiton

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
Locate the -01 and -02 components. Trial fit the two parts making sure the rectangular outlet face is flush. De-burr and trim as necessary. Caution: Care should be exercised when working with fiberglass/epoxy components. epoxy resin and sanding dust can cause an allergic reaction. When epoxying components they must be clean and free of oils and residues. 2.0 Lightly sand the mating surfaces of the two components with #150 grit sandpaper. 3.0 Clamp the two components together and check to insure the outlet face is flush. When the Inlet Assembly is installed the outlet will have the oil cooler attached to it. Therefore, the flange must
34. Oil Cooler Inlet Install Arion Aircraft, LLC Revision 0 1/4/2007 Page 35 – 3 be cut back from the outlet face. Mark the two flanges 1/8 inch from the end. Cut away the two flanges. Smooth the edges where the cuts were made. Page 2 Part Number 160904-01Rev.A 4.0 Pilot drill four holes per side to accept 1/8 inch “pop” rivets (not supplied). These rivets should be located at least 1.5 inches apart and centered on the flange. Final drill holes to size. 5.0 Separate the parts and de-burr the rivet holes. Final inspect the components and clean the mating surfaces with epoxy thinner, lacquer thinner, or Methyl Ethyl Ketone (MEK). 6.0 Mix a small quantity of epoxy (not supplied) and coat both mating surfaces of the components. Mate the two components and install the rivets. Allow Inlet to cure for 24 hours. 7.0 Cut out the center of -03 plate using the 160904-02 template supplied. Trial fit the Oil Cooler Attachment Flange. Once it mates properly and is flush with the -01/-02 assembly, lightly sand the mating surfaces of the two components with #150 grit sandpaper. Also, sand an area completely around the flange extending ½” outward from the cut-out on one face only. Final inspect the components and clean the mating surfaces with epoxy thinner, lacquer thinner, or Methyl Ethyl Ketone (MEK). 8.0 Mix a quantity of epoxy (not supplied) thickened with colloidal silica (not supplied) to a paste consistency and coat both mating surfaces of the components. Mate the two components and create a fillet completely around the flange. Allow Inlet to cure for 24 hours

harley davidson oil filter cooler installation instructions

0

Filed Under (Harley Davidson) by admin on 10-04-2012

download
2000 cH ROME 99 – 07 SOFTAIL MODELS #2001 CHROME 99 – 07 DYNA MODELS #2002 CHROME 99 – 07 FLT MODELS, flht, flhr, fltr #2005 black CHROME 99 – 07 SOFTAIL MODELS #2006 BLACK CHROME 99 – 07 DYNA MODELS #2007 black CHROME 99 – 07 FLT MODELS, flht, flhr, fltr #2020 REPLACEMENT OIL FILTER #’S: 2000, 2001, 2002, 2005, 2006, 2007 1. See Figure 1 to verify all Feuling components and the proper mounting bracket for your model 2. Wash, clean and inspect all new Feuling hardware, Including – off-set sandwich oil filter adapter, filter cooler housing and oil lines, use compressed air to blow dry the oil lines, fittings, threads and bolt holes. Use a tap and die if needed to clean threads. (On installation use lubrication on all fasteners and fittings) 3. Refer to the proper service manual for your model motorcycle & engine, for removal of engine oil and spin-on oil filter. Dispose of these items properly. 4. Clean engine case oil filter spigot and sealing surface thoroughly. 5. Install the clean Feuling off set oil filter sandwich adapter; both O-ring and gasket need to be assembled dry. 6. First install the inside half of the off-set oil filter adapter, O-ring side towards engine case filter mount. We recommend using a dab loctite on the 1″ lock nut. (See figure 2) It is recommend to mock up the sandwich adapter before torquing nuts and bolts to obtain desired orientation and proper clearance to engine case and frame rails. 7. Install the fittings and oil lines onto the outer half of sandwich adapter torque fittings to proper specs using thread sealant on the 1/8 NPT threads and engine oil on the -4 AN oil line fittings. 8. Complete installation of sandwich adapter, including the inner gasket. Finger tight the allen head bolts in an alternating sequence on both sides before final torque. Re-Torque the allen head bolts after the first heat cycle after installation and during every oil change.

SMALL COOLER RACK LIGHTING SYSTEM INSTALLATION MANUAL

0

Filed Under (Tips and Review) by admin on 29-12-2010

download
1. Using the nuts supplied, bolt the lighting system to the rack (on some earlier production models the holes may be off slightly and require that you drill the holes in the rack larger for alignment). 2. Using a side cutting pliers, trim away the corner of the metal grating and route the wire loom thru and out the bottom of the rack as shown. Route the loom along the bottom of the rack to where the plug on the motorcycle is or will be and secure it to the rack using the cable ties supplied. 3. Cut the wires and loom to the desired length to connect to the plug on the motorcycle. Connect the wires from the loom to your mating connector (not supplied) using the wire color code shown below. If you do not have a plug on the motorcycle you will need to purchase a mating male and female five pin or wire connector set. You may also use a six pin connector set and leave one pin unused as these are more readily available. RIVCO offers a six wire molded connector set with 60″ of wire #TWC002 or a waterproof six pin connector set with dust cap #TWC00

Kawasaki ZX-9R Ninja Installation Instructions

0

Filed Under (Kawasaki) by admin on 05-11-2010

download
1. Remove the lower fairing. Remove thelower radiator mounting bolts, loosen the upper bolts and pivot the radiator forward to provide access to the exhaust nuts (flange nuts). Remove the oil cooler mounting bolts and pivot the oil cooler forward to provide access. 2. Remove the existing exhaust system and save the flange nuts for reuse. Save the stock exhaust can mounting bolt and nut for reuse as well. 3. Inspect the exhaust gaskets. Replace if necessary. 4. Assemble the head pipes 1 (blue), 2 (red), 3 (yellow), and 4 (green) by matching the joints of the same color to the pair of front Y-pipes. Do not install the exhaust springs at this time. 5. 2000 through 2002 models ONLY!!! Place a billet aluminum exhaust port centering flange Z on each TiForce headpipe -see figure 3 for details. 6. Attachthe assembled head pipe sections to the exhaust ports, but do not tighten the flange nuts fully, allowing for some adjustment in the remaining steps. Reuse the flange nuts saved from step 2 above. Make sure the ends of the headpipes fit flush and snug in the ports and centering flanges Z before tightening (’00-’02 ONLY). 7. Install the S-Bend to the front section of the headpipes and two Y-pipes. 8. Go back and retighten the head pipe flange nuts per factory specifications -make sure the headpipes and flanges Z are centered in each port (’00-’02 ONLY!!! ) . 9. Slide the TiForce end can into place. 10. Loosely attach the two rubber bands, stainless steel bands K, and stay / hanger G to the end can using the supplied 6mm hardware H. See figure 1. 11. Place the bands approximately 108 mm from the edge of the end can. See figure 2. 12. Using the stock provided mounting point on the passenger footpeg, and using the stock mounting bolt, mount the end can loosely, allowing for some adjustment. Insert the stock mounting bolt through the stay / hanger G. 13. Attach the supplied springs to all the joints, starting from the headpipes and working back to the end can. 14. Make sure the exhaust system is free and clear, if necessary jiggle the system to adjust for proper clearance. 15. Carefully align the two stainless bands K so that they are parallel to each other, and spaced properly on the can (refer to step 11 /figure 2), then tighten the 6mm hardware H and the stock mounting bolt hardware. Make sure that the rubber pads fully cover the band(s). USE CAUTIONWHEN TIGHTENING THE 6MM HARDWARE AND THE TWO BANDS SO AS NOT TO CRUSH OR DISTORT THE SLEEVE OF THE CAN. 16. Using some brake and contact cleaner on a clean rag, carefully wipe down the entire exhaust system to remove any residual oils, anti seize, fingerprints and dirt prior to starting the motor. FAILURE TO CLEAN THE TUBING AND CAN MAY RESULT IN PERMANENT STAINING OF THE SYSTEM WHEN HEATED. 17. Go back and reinstall the radiator and oil cooler as per factory specifications. Verify fluid levels as needed. 18. Checkthat all hardware is properly tightened, then start the motor and check for exhaust leaks. 19. Reinstall the fairing and tighten any fasteners per factory specification

Incoming search terms: