Filed Under (Harley Davidson) by admin on 21-03-2011
REMOVE CLUTCH CABLE 1. See Figure 1. Loosen clutch adjuster to obtain slack in the clutch cable (2) by performing the following: a. Locate cable adjuster (1) and slide off rubber boot (4). b. While holding cable adjuster with 1/2-inch wrench, loosen jam nut (3) using a 9/16-inch wrench. c. Turn cable adjuster until there is a large amount of free play at hand lever. 1 2 3 4 is 00889 1. Cable adjuster (1/2-inch) 2. Cable end 3. Jam nut (9/16-inch) 4. Rubber boot Figure 1. Clutch Cable Adjuster 2. See Figure 2. Remove the retaining ring (1), pivot pin (2) and clutch cable anchor pin (3) from the hand lever. 2 3 1 is 00891 1. Retaining ring 2. Pivot pin 3. Clutch cable anchor pin Figure 2. Clutch Cable Compoments 3. See Figure 3. Drain transmission lubricant and remove fill plug dipstick. Remove the six screws that hold the clutch release cover in place. Remove the clutch release cover, being careful not to damage the gasket. NOTE The clutch release cover gasket (P/N 36801-87B) will need to be replaced if torn or damaged to prevent transmission fluid from leaking from the release cover. 4 3 5 2 6 1 is 00894 Figure 3. Clutch Release Cover Screw Sequence 4. See Figure 4. Note position of retaining ring opening. Retaining ring opening must be positioned in approximately the same location during reassembly. Remove retaining ring (1). 5 4 1 3 2 is 00895 1. Retaining ring 2. Inner ramp 3. Cable fitting 4. Clutch cable 5. Ramp coupling Figure 4. Clutch Cable Connection 5. Pull inner ramp (2) and coupling (5) out of side cover. Hold inner and outer ramps together to keep balls from falling free. 6. Rotate the inner ramp to a position that will allow the coupling (5) to be disconnected from the inner ramp lever arm. Disconnect coupling from inner ramp. Disconnect cable end from coupling. 7. Back out threaded cable fitting from side cover. Ensure that o-ring is removed with cable. Discard o-ring. INSTALL CLUTCH CABLE 1. See Figure 4. Obtain braided stainless steel clutch cable from kit. Apply a light coat of oil on new o-ring and install o-ring (Part Number 11179) onto threaded portion of clutch cable (4). Insert clutch cable fitting (3) into clutch release cover. Do not tighten cable fitting at this time. 2. Connect cable end to coupling. Rotate ramps for best access and install coupling on inner ramp. Place ramp assembly in position in side cover. 3. Install retaining ring. Position retaining ring opening so it is located approximately over the outer ramp tang (the stop that prevents rotation). NOTE Replace clutch release cover gasket if torn or damaged. 4. See Figure 3. Place gasket, if removed, on side cover and install side cover. Tighten the six screws in the order shown to 84-108 in-lbs (10-12 Nm) . 5. Tighten the clutch cable fitting to 36-60 in-lbs (4-7 Nm) . 6. Place a few drops of oil inside cable housing. 7. Route clutch cable as follows: SOFTAIL MODELS FXSTD, FLSTS, FXSTS and FXST – Route clutch cable from the clutch release cover, across the frame, up along the front frame downtubes and across the front of the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. FLSTF and FLSTC – Route clutch cable from the clutch release cover, across the frame and up along the front frame down- tubes, up to and behind the handlebars. Cable straps (item 1 in service parts illustration) to be used in same location as original equipment straps. DYNA MODELS FXDWG – Route clutch cable from the clutch release cover, under frame and across to the left side. See Figure 5. Insert cable (1) into clip (2) at the bottom left side of the frame
Filed Under (Honda) by admin on 23-04-2011
Refer to the 2008 CBR1000RR Service Manual for specific removal instructions. While completing this procedure, be careful not to damage the covers, cowls, or any other components. 1. Remove the air intake cover (page 3-8). 2. Remove the upper inner cover (page 3-9). 3. Remove the lower cowl (page 3-9). 4. Remove the right middle cowl (page 3-10). 5. Remove the right crankcase cover (page 10-5). Clutch Removal (page 10-7) 6. Remove the starter idle gear and shaft. 7. Remove the snap ring and stopper ring. 8. Remove the clutch lifter piece and plate. 9. Unstake the clutch center lock nut. Be careful not to damage the mainshaft threads. 10. Hold the pressure plate with the special tool. You must use the special tool (Clutch Holder, T/N 070MB-MFLA100) when removing the lock nut. Using an impact wrench will damage the main shaft threads. Clutch Holder: 070MB-MFLA100 (autoshipped in May 2008) 11. Remove the clutch center lock nut and washer and discard the lock nut as shown on top of page 3 12. Remove the clutch spring holder, spring seat, and two clutch springs. 13. Remove the spring seat. 14. Remove the following: • Pressure plate
• Spring seat • Judder spring • Clutch disc A • Clutch plate A • Seven clutch discs B • Clutch disc C Clutch center NOTE: Do not remove the clutch outer. New Clutch Installation (page 10-20) NOTE: The new clutch disc assembly has a dif- ferent order of plates than the illustration shown in the Service Manual. Keep note of this when repairing updated units.
15. Install the new clutch disc assembly with- out removing the setting bolts. Rotate the main shaft to align the clutch disc assem- bly with the main shaft spline. 16. Slightly loosen the setting bolts. 17. Rotate clutch disc C to align its tabs into clutch outer shallow slots, then fully install the clutch disc assembly. 18. Remove and discard the setting bolts. 19. Install the spring seat
Filed Under (Ducati) by admin on 25-10-2010
If installing with Ducati OEM basket you need the washer cod. 0D1SR140C220045 (3mm). – If installing with STM basket (Z12 o Z48) you need the washer cod. 001MG019 (1,5mm). – Insert the correct washer on the gear shaft. – Perform the initial hub group assembly: position the progressive engagement steel plate (003MG015) on the hub (0F3SR140J24001C) , with the step facing up. Be careful to position it correctly into the specific seats, then check that pushing one side, the opposite stand up simultaneously. – Now put the 6 steel balls (001MG025) at the bottom of the grooves using a little bit of grease. Then fix the clutch drum (0F3SR140J24002C) on the clutch hub (0F3SR140J24001C) at rest position, using an M6 screw to help locking the two parts, avoiding in this way any possibility for the steel balls (001MG025) to fall out while inserting the hub pack on the main shaft. – Insert the hub pack on the gear shaft – Insert the clutch discs starting with the sintered one and finishing with the steel guided one; total disc set thickness must be included between 36 and 36,5mm. – Remove the M6 screw from the hub (0F3SR140J24001C). – Put the drum stopper hub (003MG106) on the hub (0F3SR140J24001C). – Verify that the secondary spring support (0F3SR540B140016) is well inserted into its housing on the drum (0F3SR140J24002C). – Insert the secondary spring (0S2085) into its housing on the drum (0F3SR140J24002C). – Mount the pressure plate (003MGP10) on the drum (0F3SR140J24002C) . – Position the Evoluzione spring (0S1090) on the pressure plate (003MGP10), with the convex part facing up (STM logo facing up), making sure previously that the squared section ring (901SE003), which works as primary spring support, is well positioned into the pressure plate itself. – Assemble the complete spring stopper pack: starting from the spring stopper plate (003MG008), with the shaped side facing up as shown in the picture. Insert the ball bearing (003MG007) and finally the spring stopper hub (0F3SR140N220007). Once completed these operations, position the complete spring stopper pack inside the Evoluzione spring (0S1090). – Insert the toothed washer (901RD101) with the convex side facing up, then insert and tighten up the clutch nut (0F30S140C220013); use a dynamometric wrench setting the torque suggested by the bike manufacturer. We suggest to use the specific optional tool (UTL-0020) in order to lock the pressure plate (003MGP10) while performing this operation. – Assemble the complete bearing rest pack: insert the washer (001MG018) in its housing on the bearing rest (0F3SR140N220004). Then put in the same housing the ball bearing and the push rod pin of the original clutch. – Position the complete bearing rest pack in the pressure plate (003MGP10), making sure it fits correctly into the housing grooves. – Manually practise a little pressure on the bearing rest (0F3SR140N220004) in order to release the seat for the tightness circlip (003MG018). – Fit correctly the above mentioned tightness circlip (003MG018). MAKE SURE that it adheres to all the groove perimeter. NB: Once completed the installation, repeatedly operate the clutch lever, checking that the pressure plate performs correctly the opening and closing movements. For a road use of the clutch you have to check clutch plates set every 2000 km. Please verify that the clutch plates set thickness is between 36,5mm and 35,0mm. If it is inferior to 35,0mm please replace a 1,5 steel plate with a 2 mm steel plate. For a racing use of the clutch we suggest to check the clutch plates set thickness frequently. GENERAL SAFETY REGULATIONS – In this sheet are reported the directions to perform correctly the clutch assembly operations. – STM reserves the right – without notice – to introduce any technical change whenever deemed it to be necessary to improve functionality and quality of the products. – Assembly operations must be performed by a skilled technician and must be scrupulously observed. – Before mounting the clutch make a complete inspection of the various parts, in order to verify the possible presence of faults or anomalies on the motorbike. – Make sure that there are no missing/damaged parts in the package . – Some parts of the clutch and its components can have sharp surface: handle with care. – Some components of the clutch, because of their small dimensions can be swallowed: keep away from children. STRADA srl Via Campo Archero 20 10023 Chieri ( TO ) Tel +39 011 9422832 Fax +39 011 9471447 003 MG 018 Tightness circlip
Filed Under (Harley Davidson) by admin on 11-02-2011
CLUTCH CABLE REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 1. Disconnect the battery or main fuse following the instructions in the appropriate Service manual. 2. When performing cable disassembly procedures, make careful notes as to the existing cable routing and existing cable strap locations. New straps can be installed in the same locations. 3. Remove the clutch cable following the instructions in the appropriate Service Manual. 4. If installing different handlebars, install them now (refer to the appropriate handlebar instruction sheet) and measure the change in distance that will be required from the end of the cable housing to the clutch lever. Install proper length clutch cables. Incorrect cable length can adversely affect motorcycle operation, which could cause loss of control resulting in death or serious injury. (00448b) 5. Compare the additional required length to the cable provided in your kit. If the cable is more than two inches (50.8 mm) longer or more than one inch (25.4 mm) shorter than the above measured distance, see a Harley-Davidson dealer for the correct cable length. CLUTCH CABLE INSTALLATION Sportster and Softail Models Do not over-tighten clutch cable threaded end fitting. Use recommended torque values. Damage to threaded fitting can lead to loss of transmission fluid, which could result in loss of control and death or serious injury. (00449c) -J04568
NOTE Damage to the clutch cable threaded end fitting due to improper handling/installation is not covered under the Harley-Davidson Motor Company Warranty. 1. See Figure 11. Apply a light coat of clean engine oil on the new O-ring (2) before installing the O-ring onto the threaded portion of the clutch cable end. 2. Install the clutch cable following the instructions in the appropriate Service Manual EXCEPT: Tighten clutch cable fitting to clutch release cover to 36-60 in-lbs (4-7 Nm) . Replace anchor pin with anchor pin supplied in this kit, see Figure 11, item (1 or 7). 3. After installation, follow the instructions in the “Final Assembly” and “Clutch Cable Adjustment” sections in this instruction sheet. FLTR Models with Fairing Lowers 1. See Figure 1. Carefully twist the clutch cable around the coiled opening in the clutch cable guide (2) with the eyelet toward the left handlebar. 2. Route the clutch cable assembly down from the clutch cable clamp while crossing to the right side of the vehicle. Run the cable between the inboard side of the right frame downtube and the outboard side of the voltage regulator. 3. The clutch cable clamp, mounted on the engine guard, has two fingers, an upper and a lower. Feed the cable assembly under one finger and over the other. 4. Finish the installation of the clutch cable following the instructions in the appropriate Service Manual EXCEPT: Tighten clutch cable fitting to clutch release cover to 36-60 in-lbs (4-7 Nm) . Replace anchor pin with anchor pin supplied in this kit, see Figure 11, item (1 or 7). NOTE See Figure 2. Adjust the clutch cable clamp to 2.25 ± 0.25 in. (57.15 ± 6.35 mm) as measured from the inside lower left fairing mount to the clutch cable clamp. 5. After installation, follow the instructions in the “Final Assembly” and “Clutch Cable Adjustment” sections in this instruction sheet.
Filed Under (Harley Davidson) by admin on 08-11-2010
Remove existing front wheel assembly. Save axle, axle nut, brake disc, and wheel spacers for kit installation. Refer to FRONT WHEEL in service manual. For FLSTC and FLSTN Models: Discard moon-style hub cap. -J04065 1 of 8 For FXSTD Models: Discard the tapered r ight side wheel spacer. Do not re-use brake disc/rotor screws. Re-using these screws can result in torque loss and damage to brake components. (00319c) NOTE • For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771- 07, 43609-07, 44323-07, 44282-07, 44322-07, 43975-07, 43602-07 and 43773-07 install short valve stem (43157- 83A) included in the installation kit. • For Kits 40943-09, 40966-09 and 40996-09 install long valve stem (43206-01) included in the installation kit. 2. See Figure 2. Install valve stem assembly (L, M or N) on wheel. Refer to TIRES in service manual. 3. Assemble wheel installation kit components and brake disc(s) to wheel, using the appropriate service parts table. Refer to FRONT WHEEL in Service Manual. NOTES Install the primary bearing first using appropriate service manual and WHEEL BEARING REMOVER/INSTALLER. For Kits 43573-08, 43575-08, 43703-08, 43978-07, 43771-07, 43609-07, 40943-09, 40966-09 and 40996-09: • The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and/or DOT markings to identify it as the brake disc and primary bearing side. • Install the wheel so that the valve stem is on the right side of the motorcycle. For Kits 44323-07, 44322-07 and 44282-07: • Install the wheel so that the hub markings are on the left side of the motorcycle. The left side of the wheel has a machined groove (item 5, Figure 2) in the hub face and hub markings to identify it as the primary bearing side. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). • The gross axle weight ratings is unaffected by the installation of this wheel on a vehicle equipped with a 21-inch wheel. For Kits 43975-07, 43773-07, and 43602-07: • The wheel has a machined groove (item 5, Figure 2) in the hub face to identify the right side. • For 2007 and later FX Softail Models and 2008 and later FXDWG: The left side of the wheel is the primary bearing side. For all other models the right side of the wheel is the primary bearing side. • For Kit 43602-07: An arrow is engraved into the right side hub to indicate the direction of rotation. • For Kits 43975-07 and 43773-07: An arrow is cast between the spokes on the right side to indicate the direction of rotation. • These kits include one or two hub plates (43985-00) to install between the brake disc and the wheel and a chrome hub cap (43986-00) to install on the wheel opposite the brake-disc side. Hub covers must be installed to prevent water intrusion, which could cause an imbalance condition. Dual brake disc models: Install one stainless steel hub plate (3) between each brake disc and wheel hub. Discard chrome hub cap (2). Install brake discs according to service manual procedures. Single brake disc models: Install one stainless steel hub plate (3) between the brake disc and wheel hub. Install the brake disc according to service manual procedures. Install the chrome hub cap (2) on the side opposite the brake disc. Discard extra stainless steel hub plate (3). 4. Install wheel assembly parts from the appropriate Service Parts table for this fitment and stock brake disc. Discard parts from the installation kit that are not required. Refer to FRONT WHEEL in Service Manual. 5. For FLSTC and FLSTN Models: Install wheel kit and right side wheel spacer provided in installation kit. For FXSTD Models: Install wheel kit, stock left wheel spacer and right side wheel spacer from installation kit in place of the tapered right side wheel spacer discarded in Step 1. Refer to FRONT WHEEL in service manual. For FXSTS Models: Install the left side wheel spacer provided in the kit between the stock left wheel spacer and the left fork. All other models: Install wheel spacers previously removed. 6. Install front wheel (1), stock axle and stock axle nut. Refer to FRONT WHEEL in service manual