torque stator bolts cbr1000rr 2012

You search Auto repair manual PDF torque stator bolts cbr1000rr 2012, if there are search results will appear below. If search results do not exist, please search by others keyword.



  torque stator bolts cbr1000rr 2012 Direct Download speed 5282 Kb/s

  torque stator bolts cbr1000rr 2012 Full Version speed 6162 Kb/s



How to Replacing Rear Main Seal 1

0

Filed Under (Tips and Review) by admin on 24-11-2010

download
The next day I woke up early and drank lots of coffee before going out to the garage. I knew I had two distinct problems confronting me. First, I would have to purchase an impact tool in order to loosen the six bolts holding the clutch together. Also, I would have to purchase at least three 8mm by 50mm bolts and nuts in order to prevent the clutch from exploding when the six bolts were unscrewed. For the third time in two days, I went to Sears and asked the salesman, (who I now I knew as Art,) where I could find an impact tool. He did not know what it was I was looking for, but he asked another employee and soon I had the tool as well as a 6mm Allen socket. Unfortunately, the Allen socket only came in 3/8″ drive, and the impact tool only came in 1/2″ drive. Thinking quickly, I purchased a 1/2″ to 3/8″ adapter, as well as a 3lb. dead- blow hammer. On the way home, I stopped at a Chief Auto Parts to buy the bolts I would need. The closest size they had were 8mm by 40mm, which was nearly 10mm too short. I was unsure whether the clutch cover bolts were coarse thread or fine thread, so I bought three of each, along with corresponding nuts. Finally, around 11 o’clock in the morning, I was back at the garage ready to work. I prepared the impact tool and placed the adapter and the Allen socket on it. I began to hammer on the end of the tool, trying to loosen each of the six bolts. None of them seemed to move, even though it seemed the impact tool was turning. Finally, I put the Allen socket on the breaker bar and found that all of the bolts had actually come loose. The tension from the clutch spring made it nearly impossible to see, however. I removed three of the bolts in a triangular pattern. Into these empty holes I threaded the fine- thread 40mm bolts with nuts attached and tightened them evenly. I was now able to remove the remaining Allen bolts. By slowly turning and loosening the nuts evenly on the 40mm bolts, I relieved the pressure from the clutch spring until the cover plate was free. I removed the cover plate, the clutch, the pressure plate, and finally the clutch spring. I had already marked each of the elements with Whiteout to insure that they would fit together the same way on installation. Apparently, this is essential as the flywheel could be rendered out-of-balance if the clutch components are not installed correctly. The flywheel itself was now exposed. I could see the five bolts that attached it to the crankshaft. I now used a tool I had fabricated. Although the manual describes two possible tools that can be fabricated, I found a piece of metal that resembled the tool and decided to use it. Unfortunately it was not strong enough and broke. I turned and looked at my workbench, and noticed a bracket which I had previously fabricated for mounting a mirror on my Vespa. The piece of steel was extremely strong and was already pre-drilled with correct-sized holes. It fit perfectly, so I placed it over the exposed bolt which protruded from the case, and placed the other end on one of the 40mm bolts, which I then bolted into the flywheel itself. I used the breaker bar again and removed the five bolts. The flywheel came loose after inserting two more 40mm bolts and tugging on them evenly

Incoming search terms:

2007 CBR1000RR REPSOL EDITION SET-UP INSTRUCTIONS

0

Filed Under (Honda) by admin on 23-04-2011

download
1. Remove the crate cover and check for damage. The CBR1000RR Repsol Edition is crated at the factory in either a covered or uncovered crate. You may receive either one. Polypropylene covered crate: Cut the strap, open the  fastener, and remove the polypropylene cover. Carton covered crate: Cut the strap and remove the carton cover. Remove the cardboard top. Uncovered crate: When stacking, protect the motorcycle from falling objects and bad weather. Check the unit for damage. If damage is found, follow the instructions on the Delivery and Damage Claims Guidelines wall chart (Reorder No. S0477) before proceeding further. 2. Remove the parts carton. Cut the strap and remove the parts carton from the crate base. Keep the You and Your Motorcycle – Riding Tips & Practice Guide booklet separate and hand deliver to the customer at the time of delivery 4. Remove the shipping bracket nuts and plate. Remove the nuts and plate that attach the front shipping bracket to the upper shipping brace. 5. Remove the rear  shipping brackets. While supporting the rear shipping brackets, remove and discard the nuts, bolts, and rear shipping brackets on both sides of the motorcycle. Install and torque the 8 x 22 mm socket bolts to secure the passenger footpeg brackets. Torque: 37 N·m (3.8 kgf·m, 27 lbf·ft) 6. Lift off the crate frame. Remove the bolts that attach the crate frame. Using two people, carefully lift off the crate frame. Use extreme care not to damage the motorcycle while  removing the crate frame. 7. Remove the front shipping bracket. Being careful not to damage the upper cowl, remove the bolts and front shipping bracket. Install the top triple clamp caps. PARTS QTY Socket bolt 8 x 22 mm 2 PARTS QTY
Top triple clamp cap 2 UPPER SHIPPING BRACE NUTS PLATE 8 x 22 mm SOCKET BOLT REAR SHIPPING BRACKET BOLT NUT BOLTS FRONT SHIPPING BRACKET CAPS BOLTS Page 8 İ2007  5 8. Relocate the ignition keys. Remove the ignition keys and protective tube from the throttle cables. Remove the packaging from the keys and insert one of them into the ignition

2003 KING Owners / Service Manual

0

Filed Under (Cobra) by admin on 01-12-2010

download
Specifications – General Items KING Dimensions Wheelbase 39″ (991mm) Wheel size 10″ (254mm) rear, 12″ (305mm) front Seat height 26″ (660mm) Engine Type 2-stroke, single cylinder, reed valve Cooling system Liquid-cooled Displacement 49.8 cc Bore and stroke 39 mm x 41.7 mm Ignition system Electronic Spark plug Splitfire SF406B Gap 0.023″ – 0.025″ (0.58 – 0.64 mm) Ignition timing 0.050″ (1.3 mm) Before To Dead Center (BTDC) Fuel type Sunoco MO2 X or 93 octane pump gasoline OTHER RACE FUELS ARE NOT RECOMMENDED Oil type Cobra Venom 2-cycle Race Oil Fuel / oil mix ratios Between 32:1 and 40:1 (after engine Break-In is complete) Carburetion 19 mm Dell’Orto Main Jet 94 Slow (Pilot) jet 65 Float Height 16mm + 0.5mm (0.63″ + 0.020″ Transmission Speed Single Clutch Cobra 3 shoe Final drive ratio 13/39 T Chain 100 links 420 Transmission / clutch oil type Cobra Venom 3 Shoe Clutch Milk, or Dexron III Quantity 235 ml (8.0oz) 5 Chassis Front tire 2.50 – 12 Pressure 15 psi minimum Rear tire 2.75 – 10 Pressure 15 psi min. (20 psi for hard pack or rocky conditions) Front fork Cobra 30mm USD Fork oil type SAE 5 weight Fork oil amount 118 ml (4.0 oz) Optional Components • Carburetor jets • Sprockets o Front o Rear • Suspension Springs Weight of Rider (lb) Fork Spring Shock Spring Less than 51 7 lb/in, KCKG0007 SCKGOH10 (yellow, 175lb/in) 51 – 60 9 lb/in, KCKG0009 SCKGOH85 (gray, 185 lb/in) Greater than 60 12 lb/in, KCKG1200 SCKG0H, (white, 195 lb/in) • Suspension Valving Damping Rate Fork Valving Compression (base valve) Fork Valving Rebound (mid valve) Shock Valving (kit) Soft (fast) KAKG0013 KAKG0016 SCKGOH24A Standard KAKG0014 KAKG0017 SCKGOH24 Hard (slow) KAKG0015 KAKG0018 SCKGOH24B • Cobra BIG AIR SX Fork Kit part #KKKG2003 6 Specifications – Torque Values Torque Value Fastener ft-lb in-lb Nm Size & Remarks Cylinder head nuts 9.2 110 12 ¼” Crankcase bolts 6.6 80 9 6 x 1.0 Spark plug (SP) (SP) (SP) 14 x 1.25 Stator bolts 2.1 25 2.8 #8 Stator cover bolts 1.7 20 2.3 #8 Clutch cover bolts 5.8 70 7.9 6 mm Clutch 40 480 54 10*** Front axle nut 25 300 34 12 x 1.25 Front brake caliper Engine mount bolts 22 265 30 8 mm Swingarm Pivot 21 250 28 14 mm Intake manifold bolts 4.6 55 6.2 6 mm Rear Axle Bolt 25 300 34 12 mm Rear Sprocket Bolts 18 216 24 7 mm Fork cartridge rod 12 144 16 Triple clamp bolts 6 72 8 6 x 1.0 Fork cap 5 60 6.7 1.25″ x 18 Ignition rotor nut 40 480 54 10 mm** ** Use green (wicking / bearing retainer) thread locker, with primer, on the flywheel / crankshaft taper but none on the threads.

2008 FLT Police Models Service Manual Supplement

0

Filed Under (Harley Davidson) by admin on 25-11-2010

download
ITEM SERVICED 14-21 ft-lbs (19.0-28.5 Nm) Drain plug torque Engine oil and filter 4 qt. (3.8 L) Oil capacity Hand tighten 1/2-3/4 turn after gasket contact Filter 63798-99A Chrome filter part number 63731-99A Black filter part number FORMULA+ TRANSMISSION AND PRIMARY CHAIN LUBRICATION (Part No. 99851-05) Lubricant type and capacity Primary chain lubricant Wet: 38 oz. (1124 ml) Dry: 45 oz. (1331 ml) 14-21 ft-lbs (19.0-28.5 Nm) Primary chaincase drain plug torque 1/2-1 turn Adjuster screw free play Clutch adjustment 72-120 in-lbs (8.1-13.6 Nm) Adjuster screw locknut torque 1/16-1/8 in. (1.6-3.2 mm) Free play at hand lever 84-108 in-lbs (9.5-12.2 Nm) Clutch inspection cover torque Dipstick at FULL with motorcycle on jiffy stand and filler plug resting on threads. Lubricant level Transmission lubricant FORMULA+ TRANSMISSION AND PRIMARY CHAIN LUBRICATION (Part No. 99851-05) Lubricant type and capacity 32 oz (0.95 liters) 14-21 ft-lbs (19.0-28.5 Nm) Transmission drain plug torque 25-75 in-lbs (2.8-8.5 Nm) Transmission filler plug/dipstick torque Front: 36 psi (248 kPA) Pressure: solo rider Tire pressure and wear Rear: 36-40 psi (248-276 kPA) Replace if less than 1/32 in. (0.8 mm) of tread pattern Wear 55 in-lbs (6.2 Nm) minimum Spoke nipple torque Wheel spokes 99953-99A (12 oz.) D.O.T. 4 hydraulic brake fluid part number Brake fluid level Front: 0.20 in. (5.0 mm) Fluid level (from top of master cylinder reservoir) Rear: 0.26 in. (6.5 mm) Front: 7-10 in-lbs (0.8-1.1 Nm) Master cylinder reservoir cover screw torque Rear: 12-15 in-lbs (1.4-1.7 Nm) 0.016 in. (0.4 mm) Minimum brake pad thickness Brake pads and discs 75-102 in-lbs (8.5.-11.5 Nm) Brake caliper pad pin torque Front: 0.18 in. (4.5 mm) Minimum brake disc thickness Rear: 0.25 in. (6.3 mm) 0.008 in. (0.2 mm) Maximum brake disc lateral runout (warpage) 10 lb. (4.5 kg) Upward force applied at midpoint of bottom belt strand Drive belt deflection 3/8-7/16 in. (9.5-11.1 mm) FLHTP 1/4-5/16 in. (6.4-7.9 mm) FLHP/FLHPE 40-60 in-lbs (4.5-6.8 Nm) Air cleaner cover bracket screw torque Air cleaner 36-60 in-lbs (4.1-6.8 Nm) Air cleaner cover screw torque LOCTITE MEDIUM STRENGTH THREADLOCKER 243 (BLUE) Air cleaner cover screw Threadlocker Part No. 99642-97 (6 ml) LUBIT-8 SUPER OIL, Part No. 94968-85TV (1/4 fl. oz.) Lubricant part number Clutch cable 35-45 in-lbs (4.0-5.1 Nm) Handlebar switch housing screw torque

Incoming search terms:

HARLEY DAVIDSON CHROME BELT SPROCKET COVER KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
Installation 1. Remove rear wheel. Refer to the applicable Service Manual for the proper removal procedure. 2. Remove bolts and washers from sprocket. •If you intend to install Acorn Nut and Stud Kit (Part No. 91734-85), refer to that Instruction Sheet at this time (please note that this Acorn Nut and Stud Kit does not fit Sportster (XL) models). •If you do not intend to install Acorn Nut and Stud Kit (Part No. 91734-85), retain bolts and washers for reassembly. Proceed to Step 3. 3. Position sprocket cover so that its mounting holes align with the holes in the sprocket. NOTE There is only one position which allows each hole in the cover to align with a hole in the sprocket. If replacement bolts, washers, or nuts are required, use only genuine Harley-Davidson parts specified for your particular model. Aftermarket fasteners can adversely affect performance, which could result in death or serious injury. NOTE • See Harley-Davidson service manual for proper torque val- ues; •Aftermarket fasteners may not have the specific property requirements to perform properly. 4. Install bolts with washers through holes in sprocket cover and sprocket, and into threaded holes in wheel hub. Depending on the tensile strength grade of the bolts in your particular application, tighten bolts in a crosswise pattern to one of the torque values listed in the following table: 5. Refer to the applicable Service Manual for the proper procedure and perform the following: •Install axle. •Align belt. •Adjust belt tension. •Tighten rear axle nut to 60 – 65 ft-lbs torque. 6. Check sprocket for radial runout (eccentricity). If runout is visible, mark outer edge of sprocket at the location of runout. Loosen sprocket bolts and tap the marked location with a rubber mallet. Tighten sprocket bolts in a crosswise pattern to the applicable torque specified in Step 4.

Incoming search terms:

1999-2001 DUCATI Monster INSTALLATION INSTRUCTIONS

0

Filed Under (Ducati) by admin on 25-10-2010

download
It is essential to use Blue Loc-tite on all nuts and bolts. Remove any other steering stabilizers. 2) Cover the tank with an old sweatshirt or protective device so you don’t scratch it. 3) General concept for this mount: The new key cover is the anchor point for the stabilizer, so it must be fitted correctly as per the instructions below. The base of the new key cover must sit flush all the way around to provide the support needed. The bolt lengths are critical, so be sure you read the instructions carefully so you know which bolts go in which spots! 4) Remove the (4) 8x85mm Allen bolts that hold your handlebars tight. There are plastic plugs in the tops of these bolts that must be removed before you can access the Allen head. Replace the stock top barclamp with the one provided in the kit. 5) Tighten the 4 bolts evenly so the gaps between upper and lower perches, front to back, are even. 6) Remove the (2) 6x12mm Allen bolts and the plastic key cover that covers your key switch. 7) Fit the new billet aluminum key cover over the key switch and be sure the new cover is sitting down flush all the way around on the frame. It needs to be touching the frame to function properly. We’ve machined this part to fit precisely on the bike but each bike can vary slightly due to machining variations from the Ducati Factory. The new key cover should center itself by locating on the 2 spacer/nuts underneath. You might need to loosen the 2 bolts on the underside of the frame to allow those spacer/nuts to find their centering point on our key cover. 8) Note: Your stock key switch itself has a casting knub near its base that could restrict our new cover from sitting all the way down flush. We’ve machined a clearance notch inside our part for this knub to fit into, but it is possible it could vary from bike to bike, which might require a bit more clearance filing. Be sure the key cover is sitting down flush against the frame. 9) We’ve machined the key cover to fit over a 20mm spacer nut / .805″. If for some reason the stock “spacer/nuts” are too tall, you may have to file them slightly to allow the Billet key cover to sit down flush and touch the frame. 10) Once the key switch cover is flush against the frame, all the way around it’s base, retighten the bolts that hold the spacer/nuts secure from the under side of the frame using Loc-tite. Reinstall the (2) 6x12mm stock key cover bolts to a maximum of 6-ft/lbs . The stock key cover bolts are designed to engage 6mm of thread in the spacer nut. Do not be tempted to use any longer bolts than 6x12mm or they can prematurely bottom out which will keep the key cover from tightening. Shorter than 6×12 or if the cover is not flush, makes it possible to damage the threads. Double check these key-cover bolts after your first ride, as they may loosen after initial movement from the damper

Incoming search terms:

2000 Honda Rancher ATV Winch Mounting Kit REMOVAL AND INSTALLATION

0

Filed Under (Honda) by admin on 13-01-2012

Begin by removing the front fascia and front skid plate on the vehicle as shown in figure 1. Save the fasteners as they will be used later to re-install the front fascia and skid plate. 2. Remove the 8mm bolts on both sides located inside the front tires and on the ends of two horizontal tubes on the front tube frame as shown in figure 2. 3. Place the mounting plate (A1) inside the front tube frame. The tabs with the slotted holes facing down. The slotted tabs should align where the
two 8mm bolts were removed in step 2. Reinstall these two bolts at this time thighten to just fingertight. Install the two 1/4-20 u-bolts (B3) and locking hex nuts (B1) and flat washers (B7) at thism time see figure 3, do not tighten down at this time. so the plate can be adjusted for position see figure 2. 4. Place the rear support bracket (A4) into position
and attach with the two 5/16-18 x 3/4 hex cap screws (B6), flat washer (B5) and locking nut (B4). Adjust the position of the support bracket so that it comes in contact with the frame tubes and tighten the fasteners see figures 3 and 4.
Make sure the support bracket maintains contact with the rear frame tubes and tighten down the two front 8mm mounting bolts. Tighten the bolts to a recommended torque of 12 ft-lb (17 N-m). 5. Attach the fairlead bracket support (A2) to the front frame tubes see figure 5. The support bracket attaches behind the front tubes. Space the bracket away from the tubes using the spacer brackets (A3). Attach the brackets using the 1/4- 20 u-bolts (B2), lock nuts (B1) and flat washers (B7). Before tightening the u-bolts make sure the bracket is in the correct position by fitting the front
fasica into postion and checking location. Tighten the nuts to a recommended torque of 7 ft-lb (10 N-m). NOTE: If this kit is being installed on a 00 to 03 Honda the wider fairlead bracket (A2) will need to be used. This will require the use of the
wider u-bolts (B3). The spacer brkts (A3) will not be required when installing the wider fairlead brkt

Incoming search terms:

2003 CM50 Owners And Service Manual

0

Filed Under (Cobra) by admin on 01-12-2010

download
Fastener ft-lb in-lb Nm Size & Remarks Cylinder head nuts 9.2 110 12 ¼” Crankcase bolts 6.6 80 9 6 x 1.0 Spark plug (SP) (SP) (SP) 14 x 1.25 Stator bolts 2.1 25 2.8 #8 Stator cover bolts 1.7 20 2.3 #8 Clutch cover bolts 5.8 70 7.9 6 mm Clutch 40 480 54 10*** Engine mount bolts 22 265 30 8 mm Swingarm Pivot 21 250 28 14 mm Intake manifold bolts 4.6 55 6.2 6 mm Ignition rotor nut 40 480 54 10 mm** Rear Sprocket Bolts 18 216 24 7 mm Rear shock mounts 40 480 54 10 x 1.5 Rear Axle Bolt 25 300 34 12 mm ** Use green (wicking / bearing retainer) thread locker, with primer, on the flywheel / crankshaft taper but none on the threads. *** Use green (wicking / bearing retainer) thread locker, with primer, on the crankshaft / clutch taper but use red (high strength) thread locker, with primer, on the nut. (SP) To apply the proper torque to the spark plug when inserting, one must first screw the spark plug in until the metal gasket ring causes resistance and then turn another 1/8 to ¼ turn. 7 Optional Components • Carburetor jets • Sprockets o Front o Rear • Seat with lower seat height, 22″ (559 mm), # TCHO0001 • Suspension Springs Weight of Rider (lb) Fork Spring Shock Spring Less than 38 (light) KCMZ0012A SCMU0321 (yellow, 320 lb/in) 38 – 45 (std) KCMZ0012 SCMU1360 (red, 260 lb/in) 46 to 55 (stiff) KCMZ0012B SCMU1380 (white, 380 lb/in) Extra stiff SCMU1400 (silver, 400 lb/in) • Suspension Valving Damping Rate Fork Valving Compression (right) Fork Valving Rebound (left) Shock Valving (kit) Soft (fast) KCMZ0033A KCMZ0032A SCMU0318A Standard KCMZ0033 KCMZ0032 SCMU031

HARLEY DAVIDSON XLH 1200cc BIG BORE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
Boring and Honing Procedures 1. Check again for burrs on cylinder gasket surfaces and remove burrs before performing Step 2. 2. Install original head and base gaskets, CYLINDER TORQUE PLATES (Part Number 33446-A) and TORQUE BOLTS (Part Number 33446-4). Tighten TORQUE BOLTS following tightening procedure given in the INSTALLATION, CYLINDER HEAD procedure in the ENGINE section of the Service Manual. NOTE Torque plates, properly tightened and installed with gaskets, simulate engine operating conditions. Measurements will vary as much as 0.001 inch without torque plate. 3. The cylinder must be bored with gaskets and torque plates attached. Bore the cylinder to 0.003 inch under the desired finish size. 1 WARNING CAUTION CAUTION 1 WARNING Kit Number 4. Hone the cylinder to its finished size (See Figure 1) using a 280 grit rigid hone followed by a 240 grit flexible ball hone. Honing must be done with torque plates attached. All honing must be done from the bottom (crankcase) end of the cylinder. Work for a 60 degree crosshatch pattern. 5. See Figure 1. After machining and honing, chamfer the bottom edge of the cylinder liner. the chamfer provides a beveled surface for easier installation of the cylinder over the piston rings. Break leading edge of liner to a flat surface. The bottom edge of the liner will be somewhat sharp after machining. This sharp edge could easily be damaged during installation of the cylinder. Piston Installation The 1200cc pistons have an arrow on the top of the piston. This arrow must face the front of the engine when piston is installed. There is no front cylinder piston or rear cylinder piston. New pistons can be installed in either cylinder. Check piston rings for proper side clearance and end gap (See XLH Service Manual). Be sure end gaps of adjacent rings are installed 90 degrees apart. Assembly Follow assembly and torque specifications given in the ENGINE section of the applicable Service Manual. Replace original gaskets, O-rings and seals with new components furnished in kit. NOTE Push rod covers on 1991 and later models are one-piece and the correct O-rings are as follows: Bottom – Part Number 17944-89 Upper – Part Number 11190 Engine Break In For the first 500 miles, to wear-in critical parts, observe these few simple driving rules: During the first 50 miles, keep the engine speed below 2500 RPM in any gear. Up to 500 miles, vary the engine speed, avoiding any steady speed for long distances. Engine speed up to 3000 RPM is permissible in any gear. Avoid fast starts at wide open throttle. Drive slowly until engine warms up. Avoid running the engine at extremely low RPM in higher gears. 2 of 3 -J00001 1200cc CYLINDER FINAL BORE SIZE AFTER HONING STANDARD BORE DIAMETER 3.4980 inch + 0.0002 inch Figure 1. Bottom Edge of Cylinder Liner Chamfer i04852 Break Edge to Flat Surface

Incoming search terms:

YAMAHA YZF-R1P YZF-R1PC ASSEMBLY MANUAL

0

Filed Under (Yamaha) by admin on 26-02-2011

download
PREPARATION To assemble the motorcycle correctly, supplies and working space are required. Supplies oils, greases, shop rags. Workshop The workshop where the motorcycle is assembled should be clean and large. The floor should be level. Self-protection Protect your eyes with suitable safety spectacles or safety goggles when using compressed air, when grinding or when doing any operation which may cause particles to fly off. Product hands and feet by wearing safety gloves or doing. SYMBOLS USED ON CRATE CARTON Contents of the transport package are fragile therefore it shall be handled with care. Indicates correct upright position of the transport package. Transport package shall be kept away from rain. Insertion of the lift arm from this side is prohibited. Lift arm inserting position. -1- UNPACKING 1. Remove the frame cover 1. NOTE: To remove the frame cover, cut the vinyl bands around the cover using a cutter or scissors. 2. Remove the bolts 2 (upper bracket). 3. Remove the bolt 3 (front tire). 4. Remove the packing frames 4 (upward and sideways). NOTE: Remove the bolts while holding frame. NOTE: Before starting the assembly, check for damaged or missing parts. The parts are contained in the cartan and the motorcycle for damage, scratches and other defects. -2- PARTS LOCATION 1 Carton box -3- 1 Carton box Screw, washer and special nuts (windscreen) Bolt (front master cylinder) Bolt (handle crown and handlebar) Nut (rear view mirror) Nut (front reflector) Front reflector Vinyl bag 1 Plugs (handle crown) Owner’s manual Rear view mirrors Windscreen – -5- 1. Handlebar 1 2 3 4 5 6 1 1 1 1 2 1 Reservoir tank (brake) Hexagon socket bolt Crown nut Hexagon socket bolt Cap Hexagon socket bolt * V * V V * d = 6 (0.24), r= 12 (0.47) d = 6 (0.24), r= 25 (0.98) d = 8 (0.31), r= 30 (1.18) 2. Front reflector A: Tighten the crown nut to specified torque. Tightening torque: 115 Nm (11.5 m • kg, 85.0 ft • lb) B: Tighten the bolt to specified torque. Tightening torque: 13 Nm (1.3 m • kg, 9.4 ft • lb) C: Tighten the bolt to specified torque. Tightening torque: 13 Nm (1.3 m • kg, 4.4 ft • lb) A: Tighten the screws to specified torque. Tightening torque: 40 Nm (4.0 m • kg, 29 ft • lb) 1 2 3 4 5 2 2 2 4 4 Reflector bracket Reflector Nut Washer Caliper bolt * V V * * d = 5 (0.20) d = 10 (0.39) d = 10 (0.39), r= 30 (1.18) 3. Clutch cable 1 Clutch cable 1 * A: Check the clutch lever for smooth action. CAUTION: Proper cable routing is essential to assure safe motorcycle operation. Refer to “CABLE ROUTING

Incoming search terms:

Incoming search terms: