tour pack relocation kit

You search Auto repair manual PDF tour pack relocation kit, if there are search results will appear below. If search results do not exist, please search by others keyword.

HARLEY DAVIDSON FLHTCUSE TOUR-PAK INSTALLATION KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 26-03-2011

download
INSTALLATION Prepare Motorcycle for Service 1. See the Owner’s Manual and remove the seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) 2. Remove the bolt and negative (-) battery cable from the battery. 7 6 5 4 3 1 2 is01951 1. Loading coil assembly 2. Nut 3. Lock shroud 4. Clip, locking (Sold Separately) 5. Nut 6. Screw 7. Tour-Pak lockset Figure 1. Antenna Loading Coil and Tour-Pak Lock Installation 3. Remove the bolt and positive (+) battery cable from the battery. 4. Install a Tour-Pak Rack kit (53276-04, 53118-98A or 53260-02) according to the Instruction Sheet contained in the kit. 5. For FLHX and FLTR models: Install Antenna Relocation kit according to the instruction sheet in that kit. NOTE Discard antenna mounts from antenna relocation kit and use mounts supplied with this kit. To open the Tour-Pak prior to installing the Tour-Pak lock, insert a flat head screwdriver into the lock location and turn clockwise while pulling up on the lid. 6. Install the Tour-Pak onto the Tour-Pak Rack using the hardware included in the Tour-Pak Rack kit according to Instruction Sheet included with that kit. Install Tour-Pak Components

HARLEY DAVIDSON TOUR-PAK RACK LIGHT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 06-02-2011

download
INSTALLATION 1. Remove all contents from Tour-PakĀ®. 2. For easier installation, remove Tour-Pak rack, if installed, by removing cap screw, washers and mounting pads. 3. See Figure 1. Remove rubber plug from bottom rear rail on left side of rack. 4. See Figure 2. Use line wire feeder in kit to thread through left rear rack foot and out through the back opening of rail. 5. Attach light harness wires to line wire feeder loop. 6. Carefully pull line wire feeder and light harness wires through rack mounting foot. 7. See Figure 5 and Table 1. Apply foam pads (5) to top surface of light. 8. Secure light (1) to rack with socket head screws (4) and washers (6). 1 is05242 1. Plug Figure 1. Left Side Rack Plug 1 is05244 1. Line wire feeder Figure 2. Thread Wires Through Rack 9. Position rack/light assembly to Tour-Pak lid and route wires through lid, washer and hollow mounting bolt. 10. Attach rack/light assembly to Tour-Pak using instructions and hardware provided with rack except for use of hollow bolt from Step 9. 11. Remove Tour-Pak liner. 12. Thread wires through black vinyl conduit. 13. Ultra Classic models: Follow Steps 14 through 2114. Locate and disconnect three pin AMP connector for Tour- Pak lights. 15. See Figure 3. Attach the Y-harness (2) to the three pin male connector (1) of Tour-Pak harness. 16. Route light wires from back of Tour-Pak along left side to front. Secure conduit with adhesive clips provided in kit. 17. Trim length of light wires and conduit to reach Y-harness. 18. Refer to the Service Manual electrical appendix to install terminal pins (8) to rack light wires and install terminals to three pin housing (7) as follows: a. #1 cavity = blue lead b. #2 cavity = red with yellow lead c. #3 cavity = black lead 19. Connect rack light to remaining Y-harness connector. 20. Replace Tour-Pak liner. 21. Check operation of Tour-Pak tail and stop light functions before operating motorcycle. 22. Classic models: See Figure 4. If necessary, drill hole in lower left bottom of Tour-Pak and install grommet. Route rack light wires through grommet. 23. Refer to the Service Manual electrical appendix to install terminal receptacle (8) to rack light wires and install terminals to three pin receptacle housing (7) as follows: a. #1 cavity = blue lead b. #2 cavity = red with yellow lead c. #3 cavity = black lead NOTE To prevent corrosion, fill the cavities of the connectors with dielectric grease (included in kit) prior to making connections. As an additional precaution against moisture seepage into the Tour-Pak, apply silicone sealant (not included in kit) to the entrance of the light harness wire tunnel. See figure 2 for location reference. 24. Connect rack light to male connector of two connector wire harness (12) and connect to accessory connector under seat. 25. Replace Tour-Pak liner. 26. Check operation of Tour-Pak tail and stop light functions before operating motorcycle

HARLEY DAVIDSON ULTRA CLASSIC AND ELECTRA GLIDE CLASSIC TOUR PACK ADJUSTMENT KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 23-04-2012

download
1. Open the Tour Pack and remove all of the contents. 2. Remove map bag and inner pack liner. Pack liner comes out quite easily once map bag is removed. 3. Remove the 4 bolts inside the tour pack that are located on top of the metal support plate that hold the tour pack to the luggage rack. Have your assistant hold the pack in place before removing the last bolt. 4. Gently tip the tour pack forward to expose the supporting luggage rack under the pack. 5. While your assistant holds the pack up, place the two adjusting bars on top of the supporting luggage rack. Use the 4 flat head screws supplied with the kit to mount the bars snugly to the support rack (see fig. 1). 6. Reposition the tour pack over the threaded holes in the adjusting bars at the 2″ or 3″ position and bolt it in place snugly (see fig. 2). 7. Replace the trunk liner and map case and the installation is complete

HARLEY DAVIDSON PREMIUM TOUR-PAK LUGGAGE RACK KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
INSTALLATION Template Positioning (Rack Installation WITH SPOILER only) The location of the luggage rack has a direct relationship to the location of the Tour-PakĀ® Spoiler. The template (7) included in this kit will locate the luggage rack in the correct position for the current or future installation of a Tour-Pak Spoiler. NOTE A template is not required if installing rack without spoiler. 1. If a spoiler is already installed, or if the installation of a Tour-Pak-mounted spoiler may be desired in the future, cut the template along the appropriate line. 2. Carefully place the trimmed template on top of the Tour- Pak, aligning the edges of the template with the top surface of the Tour-Pak lid. Tape the template to the lid in the desired location. The template will help to properly locate the rack so that a spoiler may be added in the future. Rack Installation on Tour-Pak 1. ALL installations: Open the lid, and remove all loose contents from the Tour-Pak. 2. See Figure 1. Slip the mounting pads (2) onto each of the mounting bosses (B) of the luggage rack (1). NOTES Kit 53665-87: Position rack with wide upright toward rear of vehicle. Kit 91793-85: Position rack with upright toward rear of vehicle. Carefully center the rack from left to right, and position the rack squarely on the lid for best appearance. Do not mount the rack too far forward to avoid contact with the backrest pad. 3. Position the rack on the Tour-Pak lid in the desired loca- tion. 4. Carefully raise the rack, and place masking tape (A) on the Tour-Pak lid where the four mounting bosses contact the cover. 5. Lower the rack onto the tape in the location chosen in Step 3. Using a soft lead pencil on the masking tape strips, trace a circle around each mounting boss. Remove the rack, and use a ruler to mark the exact center position of each mounting boss on the tape. 6. Drill four 1/16 inch (1.5 mm) diameter pilot holes through the masking tape and Tour-Pak lid at each mounting boss center position. Use a 9/32 inch (7 mm) diameter bit to drill the finish holes. 7. Remove the masking tape

HARLEY DAVIDSON TOURING DETACHABLE TOUR-PAK RACK INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION NOTE See Figure 3. When installing Tour-Pak to Rack in the following Steps, note that holes on Rack provide two positions for mounting Tour-Pak in desired location. 1. Place Tour-Pak on support tube and open lid. NOTE See Figure 3. In the following step, the longer bolts (6) are used for 2005 and earlier (King only) and Chopped Tour-Paks while the shorter bolts (5) are used for Leather Tour-Pak and 2006 and later King Tour-Paks. 2. See Figure 3. Obtain bolt (5 or 6), two flat washers (3), concave spacer (4) and hex lock nut (2) from kit. Align rear center hole in Tour-Pak with same hole in support tube (8). Slide bolt with flat washer through Tour-Pak, through support tube, then through concave spacer (with concave side facing support tube). At bottom of support tube, install washer (3) and nylock cap nut (2). With concavity on spacer inline with the rail, hold nut and tighten bolt until snug. 3. Obtain bolts (5 or 6), two flat washers (3), concave spacer (4) and hex lock nut (2) from kit. Align top support tube (8) with detachable tour-pak rack holes (four). Slide bolts with flat washer through Tour-Pak, through support tube, through concave spacer (with concave side facing support tube) then through rack. At bottom of detachable tour-pak rack, install washer (3) and nylock cap nut (2). With concavity on spacer inline with the rail, hold nut and tighten bolt until snug. NOTE Always install the mounting bolts from inside the Tour-Pak. If the bolts are installed upside down, then the ends of the bolts can tear the molded liner and scratch objects, such as helmets, stored inside the Tour-Pak. 4. Repeat Step 3 and install hardware to the remaining three holes in Tour-Pak and mounting rack. 5. In a crosswise pattern, alternately tighten the five bolts to 96-120 in-lbs (10.8-13.5 Nm) . Be sure that concavity on each spacer is inline with the rail and has not rotated out of position. INSTALLATION-TOUR-PAK AND RACK 1. Follow the instructions included in the docking point kit and install docking points. 2. See Figure 1. While standing behind the motorcycle, place the front Tour-Pak rack notches into the front docking points (1). Make sure the notches seat fully into the front docking points. 2 1 is04025 1. Front Docking Point 2. Rear Docking Point Figure 1. Docking Point Bracket 3. See Figure 1 and Figure 2. Position the latches over the rear docking points (2). Check to be sure the latches fit into the neck of the rear docking points as shown in figure 2. This may require some gentle squeezing or spreading of the rack

Related Item : carburetor for a 1998 royal star tour deluxe (1)Chopped Tour-Pak Craigslist (1)Harley chop pack brackets (1)hd removable tour pack brackets (1)how to mount harley davidson tour pack on 2003 yamaha roadstar (1)install king tour pack on v star 950 (1)remove harley tour pak liner (1)stripping off goldwing tour pack (1)wireing diagram for 2014 harley street glide tour pack (1)