toyota transmission serial numbers

You search Auto repair manual PDF toyota transmission serial numbers, if there are search results will appear below. If search results do not exist, please search by others keyword.



  toyota transmission serial numbers Direct Download speed 5282 Kb/s

  toyota transmission serial numbers Full Version speed 6162 Kb/s



TOYOTA/ LEXUS U150/ U250 TOYOTA/LEXUS U150/U250 PRELIMINARY INFORMATION Presented to you by Wayne Colonna Automatic Transmission Service

0

Filed Under (Toyota Manuals) by admin on 19-09-2011

Download
Starting at the beginning of production for the 2002 model year for Lexus and 2004 for Toyota, a spin-off of the U140/U240 Four speed transaxle, designated as the U150/U250 series was born. This transmission is classified as a 5 speed transmission, although it has 6 ratio’s possible in the Drive position. The U150/250 is very similar to it’s smaller brother, the U140, and actually uses some of the same parts. This Transaxles shift points, and shift feel are electronically controlled by a Powertrain Control Module. This is accomplished by the PCM monitoring engine load and adjusting solenoid duty cycle to match pressure rise and shift feel. The PCM also monitors the turbine and output speed sensors to calculate gear ratio and the Transmission Range Sensor for gear selection.

Incoming search terms:

Toyota Automatic Transmission Serial Number Locations

0

Filed Under (Toyota Manuals) by admin on 07-10-2011

download
2006-2009 4Runner, Avalon, Camry, Corolla, FJ Cruiser, Highlander, Land Cruiser, Matrix, RAV4, Sequoia, Sienna, Solar a, Tacoma, Tundra, Venza, Yar is TSB SUPERSESSION NOTICE The information contained in this TSB supersedes TSB No. TC012-06. •Applicability has been updated to include 2008-2009 model year vehicles. TSB No. TC012-06 is Obsolete and any printed versions should be discarded. Be sure tore view the entire content of this service bulletin before proceeding. Introduction The purpose of this TSB is to assist in the identification and location of serial numbers on 2006 -2009 modelyear automatic transmissions

Incoming search terms:

TOYOTA Engine Serial Number Location

0

Filed Under (Toyota Manuals) by admin on 06-10-2011

download
YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2000-2009 4Runner, Avalon, Camry, Corolla, Land Cruiser, RAV4, Sienna, Solar a, Tacoma, Tundra 2007-2009 Camry HV, FJ Cruiser, Yar is 2000-2005 Celica, Echo, MR2 Spyder 2006-2009 Highlander HV 2001-2009 Highlander, Prius, Sequoia 2003-2009 Matrix 2009 Venza The purpose of this TSB is to assist in the identification and location of engine serial numbers on 2000-2009modelyear Toyota vehicles. NOTE When writing a Field Technical and/or Product Report the serial number of the engine MUST be provided.

Incoming search terms:

TOYOTA TACOMA TRANSMISSION TO ATLAS TRANSFER CASE

0

Filed Under (Toyota Manuals) by admin on 20-09-2011

Download
Remove the stock transfer case from the stock tailhousing adapter. The stock tailhousing is retained along with the stock rubber crossmember support. Once the transfer case is removed, you’ll see a seal located in the stock tailhousing. This seal must be removed and discarded. Some tailhousings also had a bearing which also must be removed. Install the new oil seal into the large end of the seal adapter. The sealing lip should be facing down. The small end of the seal adapter has the same O.D. (outside diameter) as the old seal that was just removed from the stock tailhousing. The seal adapter is a press-fit into the stock tail and should now be installed. The kit comes with a new spud shaft which fits over the stock Toyota transmission 26 spline output shaft. This spud shaft has a Jeep 23 male spline on the opposite side which fits into a standard 23 spline Atlas case. When installing the spud shaft into the Toyota transmission, the spud shaft does not seal onto the new seal just previously installed. The seal contacts seal off of the Atlas input shaft. The adapter plate should now be installed onto the Atlas transfer case. The adapter plate indexes off of the Atlas front retainer

Incoming search terms:

HARLEY DAVIDSON ENGINE/ TRANSMISSION INTERFACE AND TOP COVER INSTALLATION INSRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-01-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. Refer to the Owner’s Manual and follow the instructions given to remove the maxi-fuse. 3 1 2 is02998 1. Transmission top cover screw (4) 2. Oil spout assembly screw 3. Upper bearing housing screw (2) Figure 1. Interface Cover Installation 2. See Figure 1. Remove and retain the four socket head cap screws (1) that fasten the front and right side of the transmission cover. See Figure 3. Obtain the chrome top interface cover (3) from the kit. NOTE The top interface cover can be carefully brought into position on top of the transmission housing from either the right or left side without removing or loosening any vehicle components. 3. Position the top interface cover over the transmission top cover. Loosely fasten the chrome cover to the top of the transmission housing with the screws removed in Step 2. 4. Obtain the chrome filler neck cover (4), 1/4-20 socket head screw (5), flat washer (6) and spacer (7) from the kit. Remove the oil level dipstick from the oil spout on the side of the transmission housing, wipe off and set it aside for later installation. NOTE Insert a clean shop rag into the oil spout opening while the dipstick is not installed. With the dipstick removed, small parts or other foreign material could fall into the transmission, leading to equipment damage or malfunction. 5. See Figure 1. Remove and discard the socket head cap screw (2) that fastens the oil spout assembly to the transmission housing. DO NOT remove the oil spout from the vehicle. 6. Place the flat washer over the threads of the new screw, and insert the screw into the unthreaded hole in the chrome filler neck cover. Place the spacer onto the screw threads. Apply a few drops of Loctite® 243 (Blue) to the screw threads, and position the chrome cover onto the oil spout on the transmission housing. Lubricate the filler neck gasket with soapy water to aid in installation. Tighten the screw to 84-132 in-lbs (9.5-15 Nm) . 7. See Figure 3. Obtain the chrome lower side interface cover (1), one #10-24 socket head screw (8) and one chrome flat washer (9) from the kit

Incoming search terms:

HARLEY DAVIDSON ENGINE/ TRANSMISSION INTERFACE AND TOP COVER INSTALLATION

0

Filed Under (Harley Davidson) by admin on 25-12-2010

download
1. Refer to the Owner’s Manual and follow the instructions given to remove the maxi-fuse. 3 1 2 is02998 1. Transmission top cover screw (4) 2. Oil spout assembly screw 3. Upper bearing housing screw (2) Figure 1. Interface Cover Installation 2. See Figure 1. Remove and retain the four socket head cap screws (1) that fasten the front and right side of the transmission cover. See Figure 3. Obtain the chrome top interface cover (3) from the kit. NOTE The top interface cover can be carefully brought into position on top of the transmission housing from either the right or left side without removing or loosening any vehicle components. 3. Position the top interface cover over the transmission top cover. Loosely fasten the chrome cover to the top of the transmission housing with the screws removed in Step 2. 4. Obtain the chrome filler neck cover (4), 1/4-20 socket head screw (5), flat washer (6) and spacer (7) from the kit. Remove the oil level dipstick from the oil spout on the side of the transmission housing, wipe off and set it aside for later installation. NOTE Insert a clean shop rag into the oil spout opening while the dipstick is not installed. With the dipstick removed, small parts or other foreign material could fall into the transmission, leading to equipment damage or malfunction. 5. See Figure 1. Remove and discard the socket head cap screw (2) that fastens the oil spout assembly to the transmission housing. DO NOT remove the oil spout from the vehicle. 6. Place the flat washer over the threads of the new screw, and insert the screw into the unthreaded hole in the chrome filler neck cover. Place the spacer onto the screw threads. Apply a few drops of Loctite® 243 (Blue) to the screw threads, and position the chrome cover onto the oil spout on the transmission housing. Lubricate the filler neck gasket with soapy water to aid in installation. Tighten the screw to 84-132 in-lbs (9.5-15 Nm) . 7. See Figure 3. Obtain the chrome lower side interface cover (1), one #10-24 socket head screw (8) and one chrome flat washer (9) from the kit. NOTE For models with mid controls, the right-side rider footrest (foot peg) support bracket must be loosened to allow installation of the lower side interface cover. After the cover has been installed, tighten the footrest bracket attaching screws to 25- 35 ft-lbs (34-47 Nm) . 8. Position the cover around the chrome filler neck cover installed in Step 6. Loosely fasten the cover to the threaded hole in the filler neck cover with the screw and washer. 9. Obtain the chrome upper side interface cover (2), three #10-24 socket head screws (8) and three chrome flat washers (9) from the kit

Incoming search terms:

HARLEY DAVIDSON ENGINE/TRANSMISSION INTERFACE AND TOP COVER INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-04-2011

download
INSTALLATION Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) 1. Refer to the Owner’s Manual and follow the instructions given to remove the maxi-fuse. 1 4 3 2 is03621 1. Transmission top cover screw (3) 2. Upper and lower rear bearing housing screw (2) 3. Upper front bearing housing screw 4. Lower front bearing housing screw Figure 1. Interface Cover Installation 2. See Figure 1. Remove the two rear bearing housing screws (2) from the side of the transmission case. 3. Remove the oil level dipstick from the oil spout on the side of the transmission housing, wipe off and set it aside for later installation. NOTE Insert a clean shop rag into the oil spout opening while the dipstick is not installed. With the dipstick removed, small parts or other foreign material could fall into the transmission, leading to equipment damage or malfunction. 4. See Figure 2. Obtain the rear interface mounting bracket (1) from the kit. 5. Apply a few drops of Loctite 243 (Blue) to the threads of the two bearing housing screws removed in Step 2. Install the rear interface mounting bracket to the bearing housing with the screws, and tighten to 13-18 ft-lbs (17.6-24.4 Nm) . 6. See Figure 1. Remove the upper front bearing housing screw (3) from the side of the transmission case. Loosen the lower front bearing housing screw (4). 7. See Figure 2. Obtain the front interface mounting bracket (2) from the kit. 8. Apply a few drops of Loctite 243 (Blue) to the threads of the upper front bearing housing screw removed in Step 6. Hook the slot in the front interface mounting bracket under the loosened lower screw head. Install the bracket to the bearing housing with the upper screw, and tighten both screws to 13-18 ft-lbs (17.6-24.4 Nm) . 9. See Figure 1. Remove and retain the three socket head cap screws (1) that fasten the right side and left front corner of the transmission cover. 10. Remove and retain the screw fastening the rear brake line P-clamp to the rear fork bracket. 11. See Figure 2. Obtain the right rear interface cover (3), two chrome 1/4-20 screws (6) and two flat washers (7) from the kit. 12. From the rear of the motorcycle, bring the right rear interface cover into position behind the rear exhaust pipe, over the bearing housing. The hole in the top surface of the cover should be positioned over the right rear transmission top cover hole. 13. Loosely fasten the interface cover to the rear interface mounting bracket with the two chrome screws and flat washers. 14. Obtain the chrome top interface cover (4) from the kit. 15. Position the top interface cover over the transmission top cover, overlapping the tab at the top front of the chrome right rear interface cover

Incoming search terms:

HARLEY DAVIDSON CHROME TRANSMISSION HARDWARE KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 17-03-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect battery cable, negative (-) cable only. NOTE The starter does not need to be removed to install this kit. 2. Remove exhaust system only if needed to access transmission top cover hardware. Refer to Service Manual for instructions. NOTES Replace existing zinc hardware with chrome-plated hardware one at a time so the transmission top and side covers do not need to be replaced. 3. Remove and discard existing six 1/4-20 x 1 in. hex socket- head screws and washers from top transmission cover. Install six chrome hex socket head screws (1) and washers (2) on top transmission cover (3). Tighten to 84-108 in-lbs (9.5-12.2 Nm). 4. Remove and discard existing two 1/4-20 x 1 in. hex socket head screws and washers from side transmission cover. Install two chrome hex socket head screws (1) and washers (2) on side transmission cover (5). Tighten to 84- 108 in-lbs (9.5-12.2 Nm). 5. Remove and discard existing four 1/4-20 x 1-1/2 in. hex socket head screws and washers from side transmission cover. Install four chrome hex socket head screws (4) and washers (2) on transmission side cover (5). Tighten to 84- 108 in-lbs (9.5-12.2 Nm). 6. Install exhaust system if previously removed. Refer to Service Manual for instructions. 7. Connect negative (-) battery cable

FLUID SPECS MODEL- YEAR 1994- 2005 FOR TOYOTA CAMRY, COROLLA AND TACOMA

0

Filed Under (Toyota Manuals) by admin on 17-09-2011

Download
Toyota Genuine Motor Oil 5W-30 Toyota Genuine Motor Oil 10W-30 Ethylene-Glycol Antifreeze Toyota Long Life Coolant Toyota Super Long Life Coolant 00272-SLLC2 Hypoid API GL-5 75W-90 Gear Lube T-IV Transmission Fluid ATF WS Transmission Fluid 08885-80306 Good brand of 80W-90 gear lube Hypoid API GL-5 80W-90 Gear Lube Castle V160 Gear Lube Sequential Manual Transmission Fluid 08885-01306 08886-02206 Synthetic Hypoid API GL-5 75W-140 Gear Lube Limited Slip Gear Oil

Incoming search terms:

TOYOTA AUTOMATIC TRANSMISSION SHIFT LOCK OVERRIDE BUTTON

0

Filed Under (Toyota Manuals) by admin on 14-10-2011

download
AUTOMATIC TRANSMISSION SHIFT LOCK OVERRIDE BUTTON 2/3 ORB COVER STORAGE: The ORB is placed in a plastic envelope with a caution label and the envelope is taped to the automatic transmission shift lever as shown below: INSTALLATION OF ORB COVER: Install the ORB cover with the index facing toward the rear of the vehicle. PRODUCTION EFFECTIVE: MODEL PRODUCTION EFFECTIVE CAMRY FROM ’93 M/Y (AUGUST, 1992) COROLLA FROM ’93 M/Y (JUNE, 1992) TERCEL, PASEO FROM ’93 M/Y (AUGUST, 1992) CELICA FROM ’93 M/Y (AUGUST, 1992) LAND CRUISER FROM ’93 M/Y (AUGUST, 1992) TMM CAMRY FROM ’93 M/Y (AUGUST, 1992) TMMC COROLLA FROM ’93 M/Y (SEPTEMBER, 1992) NUMMI COROLLA FROM ’93 M/Y (AUGUST, 1992

Incoming search terms:

Incoming search terms: