triumph motorcycles switch housinh removal

You search Auto repair manual PDF triumph motorcycles switch housinh removal, if there are search results will appear below. If search results do not exist, please search by others keyword.



  triumph motorcycles switch housinh removal Direct Download speed 5282 Kb/s

  triumph motorcycles switch housinh removal Full Version speed 6162 Kb/s



Harley-Davidson CHROME HANDLEBAR SWITCH CAP KITS installation and REMOVAL manual

0

Filed Under (Harley Davidson) by admin on 09-03-2012

download
1. Open or remove seat according to the instructions in the Service Manual. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) 2. Disconnect battery cables, negative (-) cable first. 3. Remove left and right-hand switch housing assemblies. Refer to HANDLEBAR SWITCHES in Service Manual. NOTE It is not necessary to disconnect the switch wiring to replace the switch caps. 4. Remove individual switches from switch housing. Refer to SWITCH REPAIR/REPLACEMENT in Service Manual. INSTALLATION Upper Housing Switches 1. For HORN and START switch caps, release torsion spring leg from hole in switch cap tab. Take note of how the spring is installed. The other leg of the spring can remain in the switch bracket hole. 2. See Figure 1 and Figure 5. Carefully pry stock black switch cap up off the splined actuator shaft (2) on left side of switch. -J02633 1 of 5 5 2 1 1 3 4 is 01405 1. Switch cap installed correctly 2. Switch cap removal from splined shaft 3. Switch cap removal from pivot pin 4. Switch cap installation onto pivot pin 5. Switch cap installation onto spined shaft Figure 1. Switch Cap Removal and Replacement 3. Pry the switch cap up and away from pivot pin (3) on right side of switch, and remove cap. NOTE Use the clear protective cover film to protect the chrome surface of the switch caps during installation. Remove the film after the installation is complete. 4. See Figure 5. Select proper chrome replacement switch cap from kit. 5. See Figure 1. Place cap onto switch, angling the hole on right side over pivot pin (4) on switch. 6. Carefully press switch cap down onto splined actuator shaft (5), rocking and moving the cap until shaft snaps into place in splined hole. 7. For HORN and START switch caps, insert torsion spring leg into hole in switch cap tab. 8. Toggle switch back and forth, checking for proper opera- tion. Turn Signal Switches 1. See Figure 1 and Figure 5. Carefully pry stock black switch cap up off the splined actuator shaft (2) on switch. 2. Pry the switch cap up and away from pivot pin (3) on switch, and remove cap. 3. Select proper chrome replacement switch cap from kit. Peel a clear protective installation cover from the sheet and place it over the surface of the cap. 4. See Figure 1. Place cap onto switch, angling the hole on top over pivot pin (4) on switch. 5. Carefully press switch cap onto splined actuator shaft (5), rocking and moving the cap until shaft snaps into place in splined hole. 6. Toggle switch back and forth, checking for proper opera- tion.

Incoming search terms:

2000-2010 KTM X2 SWITCH WIRING HARNESS Removal and Installation Manual

0

Filed Under (KTM) by admin on 25-01-2012

download
The included 3600-SWHA switch harness is intended for use with offroad models that do not come with a Hi/Low beam switch from the factory. The harness is compatable with stock AC lighting electrical systems as well as high output DC electrical systems. 1. Remove the stock numberplate or headlight. Remove the stock kill switch from handlebars and replace with the 3600-SWHA switch. 2. Remove the gas tank. Route the white and black leads from the 3600-SWHA under the tank following the wires from the stock kill switch. Disconnect the stock kill switch bullet and connect the white wire of the 3600-SWHA to the wiring harness. Disconnect the stock kill switch ring terminal and connect the ring terminal of the 3600-SWHA. Fully remove the stock kill switch. Be sure all the wires are safe from being burned or pinched and re-install the gas tank. 3. Disconnect the two female spade terminals from the stock headlight switch (if present). Connect the terminal with the yellow wire to the red power lead from the switch. Connect the white wire to the blue accessory output from the switch. Be sure the clear silicone sleeves are covering the stock plastic housings. 4. Connect the X2 headlight to the switch headlight plug. Note: The stock headlight plug will not be used for the X2 installation, but is still functional for connecting the stock headlight. The stock plug will turn on and off with the new headlight switch, and will be powered in either of the Low or High Beam positions

Incoming search terms:

HARLEY DAVIDSON FLAME HANDLEBAR GRIPS REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
REMOVE AND INSTALL THE LEFT GRIP 1. See Figure 1. Using a T27 TORX® drive head, remove the two screws with flat washers securing the handebar clamp (3) to the clutch lever bracket. Remove the clamp and position the clutch hand lever assembly away from the handlebar 2. Using a T25 TORX® drive head, loosen but do not remove the upper and lower switch housing screws (1). 3. Remove the end cap from the existing left handlebar grip if so equipped. Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. Do not lubricate left handlebar grip before installation. Lubricating grip can cause it to come off while riding, which could result in loss of control and death or serious injury. (00315a) NOTE Make sure that the handlebar surface and the inside of the grip are smooth, dry and thoroughly cleaned of all dirt or adhesive residue. 4. Position the new left grip (4) so the larger flange (5) is at the bottom. Push the grip fully onto the handlebar. 5. Fit the grooves (2) on the outboard side of the upper and lower switch housing over the flanges on the end of the grip, then loosely fasten the two screws. 6. Position the clutch hand lever assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the bottom of the clutch lever bracket. 7. Align the holes in the handlebar clamp with those in the clutch lever bracket, and loosely fasten the two screws with flat washers. Adjust the switch housing and clutch hand control position for rider comfort. 8. Using a T27 TORX® drive head, tighten first the upper, then the lower handlebar clamp screws to 60-80 in-lbs (6.8-9 Nm) . 9. Using a T25 TORX® drive head, tighten first the lower, then the upper switch housing screws to 35-45 in-lbs (4- 5.4 Nm) . 5 3 1 1 4 2 2 is00735 1. Switch housing screws 2. Grooves 3. Handlebar clamp 4. Left handlebar grip 5. Larger flange Figure 1. Left Handlebar Switch Housing REMOVE AND INSTALL THE RIGHT GRIP NOTE Right handlebar switch removal requires a Service Manual for your model and year of motorcycle. A Service Manual can be purchased from your Harley-Davidson Dealer. 1. Refer to the RIGHT HANDLEBAR SWITCH section of the Service Manual for removal of the switch housing assembly. This is necessary to access the throttle cables. 2. Refer to the THROTTLE CONTROL section of the Service Manual to disconnect the throttle cables and remove the existing right grip/throttle sleeve assembly. After removal, make sure that the handlebar end is clean and smooth. 3. Follow instructions in the Service Manual to install the new right grip/throttle sleeve to the handlebar and connect the throttle cables. 4. Verify that the right grip/throttle sleeve rotates and returns freely and does not bind on the handlebar or switch housing.

Incoming search terms:

HARLEY DAVIDSON MULTI-FIT BRAIDED THROTTLE/ IDLE CABLE KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-02-2011

download
REMOVAL To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 1. Disconnect battery cables, negative (-) cable first or remove the main fuse following the instructions in the service manual. NOTE When performing cable disassembly procedures, make careful notes as to the existing cable routing. Pay special attention to existing cable strap locations before removing so new straps can be placed into the same locations. Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) 2. See Figure 1. Place the cardboard insert between the brake lever and lever bracket. 3. See Figure 2. Loosen cable adjuster jam nuts. Turn cable adjusters in until they are as short as possible. This will provide enough slack for easy removal. 4. Remove the right upper and lower switch housing screws INSTALLATION Throttle and Idle Cable Installation 1. See Figure 3. Apply graphite lightly to the throttle grip inside the switch housing and on the throttle end of the handlebar. NOTE The throttle control cable has a larger diameter retaining ring crimped to the cable end than does the idle control cable. For assembly, apply a drop of light oil on the retaining rings of the crimped inserts. 2. See Figure 7. Push the throttle cable housing and retaining ring into the larger hole of the switch housing, located in front of the tension adjuster screw. 3. Push the idle cable housing and retaining ring into the smaller hole of the switch housing, located behind the tension adjuster screw. 4. Push the throttle and idle control cable housings into the lower switch housing until each snaps into place. NOTE For models not equipped with factory-installed cruise control, if the friction shoe has fallen out or become dislodged, install the shoe with the concave side facing up and position it so the pin hole is over the point of the adjuster screw. 5. Push the throttle control grip over the end of the right handlebar until it bottoms against the closed end. Rotate the grip until the ferrule notches are at the top. To prevent binding, pull the grip back about 0.12 inch (3.2 mm). 6. See Figure 3. Position the lower switch housing beneath the throttle control grip. Install two brass ferrules (Item 3, Figure 11) from this kit onto cables, seating the ferrules in their respective notches on the throttle control grip. The cables must be captured in the grooves molded into the grip. 7. Position the upper switch housing over the handlebar and lower switch housing. Route the wire harness conduit through the depression at the bottom of the handlebar. 8. Tighten the upper and lower switch housing screws finger- tight. 9. Position the brake lever/master cylinder assembly inboard of the switch housing assembly, engaging the tab on the lower switch housing in the groove at the top of the brake lever bracket. 10. Align the holes in the handlebar clamp with those in the master cylinder housing and tighten the lower screw and flat washer finger-tight. Position for rider comfort. Beginning with the top screw, tighten the screws to 60-80 in-lbs (6.8-9.0 Nm)

HARLEY DAVIDSON VRSC FUEL TANK SIDE COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
INSTALLATION 1. Note the left and right areas on frame where the covers will be installed. Using a 50/50 mixture of isopropyl alcohol and water, thoroughly clean the frame tubes surrounding the fuel cell on the left and right sides. Let dry completely. 2. Unlock and open seat. NOTE Loosening the ignition/light switch screw (in the following step) will allow much easier alignment of the ignition/light switch cover and ignition/light switch during installation. 3. See Figure 1. At area inside of frame rail just above the ignition/light switch housing, loosen the ignition/light switch screw just enough to allow the ignition/switch switch to move slightly from side to side and up and down. Do not completely remove screw 4. See Figure 4. Obtain the right side cover bracket (ignition/light switch side) from kit. 5. Remove the strips protecting the adhesive at all of the raised sections on the cover. 1 2 is 02045 1. Ignition/Light Switch Screw 2. Ignition/Light Switch Figure 1. Loosen Ignition Switch Assembly 6. See Figure 2. Carefully align the right side cover between the three frame tubes. Beginning with the left portion of the cover, press the cover between the upper and lower frame tubes until the raised portions of cover (with adhesive) begin to snap into place. While carefully aligning the right portion of the cover, move the ignition/light switch as necessary until centered within hole in cover, then firmly press into place. Adjust ignition/light switch until the switch is centered within cover. Make sure all raised locations (with adhesive) are firmly contacting the upper and lower frame tubes and that cushion rests against front vertical frame tube. 7. See Figure 1. Tighten the ignition switch screw to 6-10 Nm (53-88 in-lbs ) . NOTE The right side (ignition/light) switch cover surface can be damaged by the key fob (from vibration) when the key is in the ignition and the bike is running. You can either remove the key fob so it does not damage the cover surface, or you can install the plastic clear sheet (included in kit) onto the side cover for protection. 8. If desired, perform the following to install the plastic clear cover onto the ignition/light switch cover. a. Obtain the plastic (rhino) sheet and hold up to the switch cover to determine proper orientation and spacing. b. Carefully peel the adhesive backing from the plastic sheet and position onto the cover. Use a wet sponge, and working out from the center, rub out any bubbles or overlapped areas under the sheet. Allow to dry completely.

Incoming search terms:

2009 TRIUMPH DAYTONA 675 Triumph/ Arrow Race Rearsets

0

Filed Under (Triumph) by admin on 12-11-2010

download
race harness kit, air funnel kit, racing oil pump gearing kit, adjustable camshaft sprocket kit, manual camshaft tensioner and blade kit, a reusable engine cover gasket set and racing cylinder head gaskets. Here’s a closer look at the new racing parts and their associated performance improvements: TRACS – Triumph Race Calibration Software TRACS ( T riumph Ra ce C alibration S oftware) is a new computer program that allows racers to tune Triumph’s programmable race ECU from a laptop PC. Developed by one of Triumph’s most experienced EFI calibration engineers, the programmable ECU and software was created for the growing number of competitors that are riding Triumph motorcycles at the track. The new software provides racers with quick access to a wide range of adjustments that can be downloaded to the race ECU in about 35 seconds for tuning during testing, practice and qualifying sessions. Features include: Fully programmable fuel mapping (500rpm increments, for individual cylinders). Fully programmable ignition mapping. Switchable wet and dry maps. Adjustable pit lane speed limiter and speedo calibration. Adjustable quickshifter cut duration (adjustable at low, mid and high RPM) Adjustable rev limiter up to 15,000rpm. New software strategies to improve throttle progression. Optimized software to run faster to cater for the higher RPMs involved in a race environment. Ability to save multiple maps within the memory of the PC. Ability to update an existing 2007/2008 Race ECU to 2009 specification and functionality.* (*Not all features will be available if using the 2007/08 Race harness.) Exhaust – Triumph/Arrow Titanium “Stage 3″ System Triumph has continued to collaborate with Italian race exhaust specialists Arrow Special Parts to develop a new, full titanium racing exhaust system. This system complies with current FIM regulations, works as part of the factory race kit, and offers a significant weight reduction and considerable power gains.

Incoming search terms:

2008 SUZUKI GSX 1300 RK IGNITION SWITCH INSPECTION/ REPLACEMENT

0

Filed Under (Suzuki) by admin on 29-11-2010

download
INSPECT ROUTING 1. Remove the upper and lower meter panels (refer to Service Manual page 9D-15). 2. Check if the ignition switch lead wire is clamped and routed correctly. Incorrect positions are shown in Figures 1 and 2. Correct routing and clamping is shown in Figures 3 and 4 on page 5. REROUTING 1. Reroute the ignition switch lead wire correctly (Figure 3 and Figure 4). The ignition switch lead wire should not be covered by the other wire harnesses. 2. Turn the handlebars back and forth to verify that the steering operates smoothly and the wiring harness does not become kinked or pinched. 3. Proceed to PUNCH MARK AT VIN on page 8. from the motorcycle (refer to Service Manual page 1H-12). Remove the two black plastic covers to access the cylinder cap mounting bolts (Figure 5). Note: The black plastic covers will not be reused. Secure the mount area (bottom) of the ignition switch in a vise (Figure 6). NOTE: Turn the ignition switch to the OFF position and remove the key from the ignition switch before disassembling the switch. Remove the two “break-off” screws from the ignition switch using the special screwdriver. Set the stepped end of the sleeve on the special screwdriver facing toward the “break-off” screws (Figure 7). Strike the special screwdriver 5 to 7 times with a hammer to produce a deep enough groove on the screw head for the screwdriver to work properly (Figure 6). Pay attention not to hit other parts with the hammer. Turn to remove the “break-off” screws in a counterclockwise direction. If the groove becomes damaged, make another groove at a 90o angle to the original groove. Remove the ignition switch from the vise and hold it upright over the workbench and carefully remove the cylinder cap (Figure 8). NOTE: Pay close attention to the order and orientation of the ignition switch parts during disassembly. REPLACEMENT OF IGNITION SWITCH (Customer Sold Units/Dealer Demo Units- Only If Inspection Shows Incorrect Routing And Unit Has Been Ridden) New Ignition Switch Disassembly 2.

YAMAHA FZR 400 ELECTRICAL CIRCUIT DIAGRAM

0

Filed Under (Yamaha) by admin on 29-11-2010

download
CHECKING OF SWITCHES Check the switches for the continuity between the terminals to determine correct connection. Read the following for switch inspection. SWITCH CONNECTION AS SHOWN IN MANUAL The manual contains a connection chart as shown left showing the terminal connections of the switches (e.g., main switch, handlebar switch, brake switch, lighting switch, etc.) The extreme left column indicates the switch positions and the top line indicates the colors of leads connected with the terminals in the switch component. “C’&-0″ indicates the terminals between which there is a continuity of electricity; i.e., a cl.osed circuit at the respective switch positions. In this chart: “R and Br” and “L/W and L/R” are continuous with the “ON” switch position. “B and B/W” is continuous with the “OFF” switch position. “B and B/W” is continuous with the “LOCK” switch position. “B and B/W” and “R and L/R” are continuous with the “P” switch position. CHECKING SWITCH FOR TERMINAL CONNECTION Before checking the switch, refer to the connection chart as shown above and check for the correct terminal connection (closed circuit) by the color combination. To explain how to check the switch, the main switch is taken for example in the following

HARLEY DAVIDSON ADVANCED AUDIO COMMUNICATION SWITCH KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
INSTALLATION To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. Refer to the Service Manual and follow the instructions given to remove the Maxi® Fuse. 2. Refer to the instructions included with the Advanced Audio Hands Free Phone Interface, CB Radio or Intercom Kit, and proceed with that installation until the installation of the items in this kit is called for. 3. Remove the outer fairing and windshield. Refer to OUTER FAIRING/ WINDSHIELD REMOVAL in the Service Manual. 4. On the fairing cap, remove the inner left side hole plug. See Figure 1 and the FAIRING CAP SWITCHES (FLHTC/U) section in the Service Manual. Install the fairing speaker switch (4) in the opening as follows: If a cruise control switch IS present: Follow the instructions in the Service Manual to install the speaker switch. If a cruise control switch IS NOT present: a. Obtain the speaker switch adapter wire (5) from the kit, and the butt splice connector included with the speaker switch. b. Refer to SEALED BUTT SPLICE CONNECTORS in the Service Manual. Splice the adapter wire to the black/ green speaker switch lead. c. Insert the terminated end of the adapter wire into cavity 12 of the fairing cap switch connector [105B] 5. Remove the original equipment left-hand control switch assembly per the HANDLEBAR SWITCHES, REMOVAL, LEFT HANDLEBAR CONTROLS instructions in the Service Manual. 6. Install the new left-hand control switch assembly (3) from the kit. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 7. ALL models: Install the console pod assembly (1), and route the harness forward into the fairing per the instructions packaged with the Advanced Audio Hands Free Phone Interface, CB Radio or Intercom Kit. Be sure that steering is smooth and free without interference. Interference with steering could result in loss of vehicle control and death or serious injury. (00371a) • Be sure the wires do not pull tight when handlebars are turned fully to left or right fork stops. 8. Unless already installed, install the overlay harness per the instructions packaged with the Hands Free Phone Interface, CB Radio or Intercom Kit. 9. Refer to the Service Manual and follow the instructions given to re-install the Maxi Fuse

Incoming search terms:

HARLEY DAVIDSON HEATED HAND GRIP KITS REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 08-02-2011

download
REMOVAL Preparation To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 1. Refer to the service manual and follow the instructions given to remove the main fuse. When servicing the fuel system, do not smoke or allow open flame or sparks in the vicinity. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00330a) 2. Remove the fuel tank according to the service manual instructions. -J04259 1 of 8 Left-Side Grip Removal 1. See Figure 1. Using a T-25 TORX drive head, remove the upper and lower switch housing screws (1). 2. Using a T-27 TORX drive head, loosen the upper screw securing the handlebar clamp (3) to the clutch lever bracket. Remove the lower clamp screw with flat washer. Loosen the clamp and position the clutch hand lever assembly away from the switch housing. Separate the upper and lower switch housings. 3. With “glueless” grip: Remove the grip from the handlebar. With glued grip: Remove the grip by carefully cutting it away from the handlebar using a sharp blade or knife. 2 2 1 5 4 3 1 is01283 1. Switch housing screws 2. Grooves 3. Handlebar clamp 4. Left handlebar grip 5. Larger diameter of flange Figure 1. Left Handlebar Switch Housing Right-Side Grip Removal Do not remove or install the master cylinder assembly without first positioning a 5/32-inch (4 mm) thick insert between the brake lever and lever bracket. Removing or installing the master cylinder assembly without the insert in place may result in damage to the rubber boot and plunger on the front stoplight switch. (00324a) NOTE A section of corrugated cardboard or the eyelet of an ordinary cable strap can be used for this purpose. See Figure 2. 1. Place a 5/32-inch (4 mm) thick insert between the brake lever and the lever bracket. 2. Using a T-25 TORX® drive head, remove the upper and lower switch housing screws. 3. Using a T-27 TORX drive head, loosen the upper screw securing the handlebar clamp to the brake master cylinder housing. Remove the lower clamp screw with flat washer. Loosen the clamp and position the master cylinder assembly away from the switch housing. Separate the upper and lower switch housings. 4. Remove the grip from the handlebar. NOTES The twist grip sensor in the right side of the handlebar has a seal cap that protects internal electrodes from dirt and moisture, and also serves as a retention device for the throttle grip. To remove the grip, a slight tug may be necessary to release the index pins in the grip from the receptacle in the seal cap. Upon removing the grip, check the location of the seal cap. If the seal cap is still fastened to the index pins inside the old throttle grip, it can be discarded along with the grip. If the seal cap is still fastened to the end of the twist grip sensor: •See Figure 3. Insert a small screwdriver or other flat-blade tool into the flat area on one side of the seal cap. •Press the leg on the underside of the cap to free it from the slot at the end of the twist grip sensor. Pry up one end of the cap. •Repeat on the other side of the cap. •Carefully remove the cap and discard it

Incoming search terms:

Incoming search terms: