turbocharger kits for vtx 1800

You search Auto repair manual PDF turbocharger kits for vtx 1800, if there are search results will appear below. If search results do not exist, please search by others keyword.



  turbocharger kits for vtx 1800 Direct Download speed 5282 Kb/s

  turbocharger kits for vtx 1800 Full Version speed 6162 Kb/s



Honda VTX 1800 Motorcycles EZ-Steer Installation Manual

0

Filed Under (Honda) by admin on 16-02-2011

download
Honda VTX 1800 EZ-Steer Instruction Installation of the Champion EZ-Steer system is similar to the installation of the OEM triple clamps of your Honda VTX 1800 Motorcycle. We strongly recommend that you use your OEM service manual and follow the prescribed disassembly, installation and torque specifications (except where noted below) for the upper and lower clamp assembly. Recommended Procedures • Disconnect all wiring to headlight and remove headlight, windscreen (if so equipped) and brackets from motorcycle. • Remove handle bars from top clamp. • Remove brake caliper and brackets; disconnect all mounting points on brake lines. Secure calipers to frame being careful not to damage brake lines. • The wheel and fork tube assembly can be removed as one complete unit. • Remove steering lock fromOEM bottom clamp and install on Champion’s bottom clamp. • Replacing the upper OEM bearing and race with the Champion supplied bearing and race, install Champion’s lower triple clamp to motorcycle reusing original hardware as removed. Torque bearing lock nut to 35 lb. ft.. • Install covers to bottom forks if supplied with OEM motorcycle. • Install Champion upper clamp with OEM washer and dome nut. Leave loose. • Slide forks up and into the upper clamp until top of forks are flush with top surface of clamp. • Torque dome nut to 75 lb. ft.. • Ensure that fork tube extensions are flush with top of upper clamp. Torque lower 8mm bolts to 20 lb.ft. and upper 10 mm clamp bolts to 30 lb. ft.. • Install handle bars to upper clamp using OEM nut and flat washers. • Reinstall brake line holders to the lower triple clamp. • Reinstall all other OEM parts as removed. • Bleed brakes. • OEM windshield # 08R80-MCH-100 can be used on this kit

HONDA VTX 1800R AND VTX 1300R SOLO RACK INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 21-12-2010

download
1. Remove the stock passenger seat. And “U” shaped mounting bracket from the rear fender. 2. Install the 2 “L” brackets provided (NOTE: there is a left and a right) onto the rear fender using the bolts from the stock bracket. Snug the bolts just enough to still allow them to slide. 3. Using the 3 knobs provided re-install the stock seat using the knob with the long stud in the rear hole. Center the slot in the seat and tighten the knob. Install the 2 knobs with the short threaded studs through the front seat mounting holes and into the new brackets. Center the bracket holes to the seat holes and snug the knobs. This will align the forward brackets. Carefully remove all three knobs and the seat. Tighten the forward bracket securely. 4. Install the solo rack starting with the 2 short knobs at the front then the long knob at the rear with the black spacer between the rack and the fender. Tighten all 3 knobs securely, as tight as you can by hand. Lost knobs are not a warrantable item. Now you can switch from your new cool solo rack look back to your stock passenger seat in seconds without any tools. NOTE: when using the stock seat, place the black spacer on the long rear knob and install them over the stock rear seat bracket. This keeps the long stud from extending below the inside of the fender and possibly contacting the rear tire if the rear shocks should bottom out

HONDA VTX, VTX RETRO AND VALKYRIE DRIVE SHAFT COVER INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 21-12-2010

download
1. Place the cover over the drive shaft housing. 2. Hook one end of the springs provided into the lower holes. Wrap the springs around the backside of the drive shaft housing. Using a needle nose pliers stretch the springs and hook them into the upper holes. 3. Note; if springs are too long, shorten and reform end to be able to hook spring in place.

HONDA VTX 1300 AND 1800 RETRO DRIVER BOARDS INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 24-12-2010

download
1. Remove the stock driver boards. Looking underneath the boards locate the pins on which the boards pivot. Remove the circlips and washers. Slide the pins out and remove the board from its mount. Note how the spring is installed. 2. Place the new board onto the mount. Slide the pin thru one side of the mount and board. Next install the spring into the open area. NOTE: the spring leg with the bent end should go into the slot or pocket on the board. Push the pin thru the spring’s center hole. Using a screw driver rotate the other leg of the spring up onto the black mount. Continue pushing the pin the rest of the way thru the board and black mount. Re-install the washers and circlips.

HONDA VTX 1800 CHROME RADIATOR COVER INSTALLATION

0

Filed Under (Honda) by admin on 29-12-2010

download
Remove the amber reflectors from the sides of the stock plastic radiator cover. These can be pried off carefully using a wide screwdriver blade or small putty knife. 2. Remove the 3 allen screws from the stock plastic radiator cover, 2 on top and 1 on the bottom. 3. Slide the chrome radiator cover over the stock plastic cover. 4. Re-Install the two original upper screws into the top holes. In the bottom hole install the button head allen screw and washer provided. Tighten all three screws. Firmly press the reflectors back onto the chrome cover

Related Item : honda vtx 1800 radiator service (1)