tvs victor gl how many size jets no in keihine carbotors

You search Auto repair manual PDF tvs victor gl how many size jets no in keihine carbotors, if there are search results will appear below. If search results do not exist, please search by others keyword.



  tvs victor gl how many size jets no in keihine carbotors Direct Download speed 5282 Kb/s

  tvs victor gl how many size jets no in keihine carbotors Full Version speed 6162 Kb/s



1991 Bimota YB10 DYNOJET KIT INSTALLATION MANUAL

0

Filed Under (Bimota) by admin on 01-11-2010

download
1. Remove the vacuum slide from the carbs. Remove the stock needles & spacers, noting the order of assembly (Fig.A). 2. Install the Dynojet needles on groove #3 , using all stock spacers (Fig. A). Install the Dynojet washer above the E-clip. 3. Replace the stock slide springs with Dynojet slide springs provided. 4. Remove the stock main jets and replace with the Dynojet main jets provided. Use the DJ116 main jets with stock exhaust pipe, or use the DJ120 main jets with aftermarket header or slip-on with high flowing baffles. Use the DJ112 main jets at high altitude. Be sure that the jets you are changing are the main jets. 5. Locate the fuel mixture plug (Fig. B), if you see a screw head, proceed to adjusting procedure. With the plug drill (DD #5/32) provided, carefully drill thru the plug(s). The mixture screw is directly underneath this plug, be ready to pull back on the drill the instant you break thru. Use the screw provided to secure and remove the plug. Carefully turn mixture screw clockwise until seated, then back out 3 turns. 6. Locate the main air correctors (Fig.C). Using the plugs provided (DCO400), plug the main air passage. Place the plug in the carb flat end first.Tap in lightly. Using DT002. STAGE ONE INSTRUCTIONS Fig. B Place E-clip in groove #3 from the top Fig. A Notes: 1. Proper EXUP value adjustment is very important for good midrange performance. 2. If experiencing fueling problems below 4,000 rpm, under full throttle, that the needle can’t fix, try changing fuel level. If you feel it is too rich, lower the fuel level. If you feel it is too lean, raise the fuel leve

Incoming search terms:

Triumph SU CARBURETORS SERVICING AND TUNING

0

Filed Under (Triumph) by admin on 29-10-2010

download
Jets: These are made in various sizes ranging from.099 inches to.1875 inches, the larger sizes being used only for racing or very high performance engines. The two sizes most commonly found on production cars are the.090 inch and the.100 inch. The size of the jet will be found stamped on the jet head. The figure “nine”wilt indicate that it is the.090 inch and the figure “one”will indicate the.100 inch jet. When tuninga production car the jets size should be checked to make sure that it is of the size recommended by the manufacturers. Centering of Jet: If for any reason, the jet assembly has been removed, it will be ne cessary to recenter the jet. First, remove the clevis pin at the base of the jet which attaches the jet head to the jet operating lever. Withdraw the jet completely and remove the adjusting nut and spring, then replace the adjusting nut, without its spring, and screw it up toits highest position. Slide the Set into position until the jet head is against the base of the adjusting nut. When this has been done, find out if the piston is perfectly free by lifting it up with the finger and allowing it to drop. If the piston is not entirely free, slacken the jet screw and manipulate the lower part of the assembly, including the projecting part of the bottom half of the jet bearing, adjusting nut, and jet head. Make sure that this assembly is now slightly loose. The piston should then rise and fall quite freely as the needle is now able to move the jet into the required central position. The jet screw should now be tightened and a further check made to determine that the piston is still quite free. When complete freedom of the piston is achieved the jet adjusting nut should be removed, together with the jet, and the spring replaced. Experience has shown that a large percentage of carburetors, which have given trouble has been due to the incorrect centering of jets. Jet Needles— These are made in a great variety of sizes, probably now well over two hundred and fifty, and each type of engine hasaneedlethat has been selected, after very careful tests have been carried out, to give the best all-round performance. Most manufacturers actually give three alternative needles for each type and size of engine, these needles clearly being listed by the manufacturer “Standard”, “Rich”or”Weak”and before tuning is started the needle, which is marked on the shank should be checked against the manufacturer’srecommendation to make quite sure that the right needle is fitted; this is most important.

Incoming search terms:

Harley-Davidson Valves, Guides And Seats Installation

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
1: Clean carbon from old guide O.D. before removal. 2: Guide to head press fit .0015″ / .002″ (head smaller than guide). 3: Heat head to approximately 200° – 250° F. 4: Install the guide at room temperature (Head hot & Guide at room temperature). 5: Let head cool to room temperature before final sizing of the bore. 6: Determine desired clearance valve to guide. Recommended clearance Shovel Head with cast iron guides Intake .001″ – .0015″ Exhaust .0015″ – .002″ (Ampco-45 add .001″) 7: Select the correct plug gage by adding the valve stem diameter and clearance desired for the finish diameter. 8: Select a plug gage .0005″ under finish size for the other end of the handle. 9: Finish hone the bore to size, check the size as you hone with the -.0005″ under size pin gage, finish hone to size with the finish plug gage pin. 10: Cut or Grind the seats, lap the valves to seats and check valve seat concentricity before assembling valve springs. 11: Use a good assembly lube, S’NS works great. 12: Use valve stem seals. Factory OE seals will stay tight with guide top size +.005″ to -.015″ from published size. 13: After the head is assembled and still on the bench check for any leakage valve to seat

TVS – 811 Series Trap Valve Station Installation, Operation and Maintenance Instructions

0

Filed Under (TVS) by admin on 29-04-2012

download
In a piston valve, the control of stem and seat leakage is obtained by tightness of the valve sealing rings to the body and valve plug. The bonnet compresses the valve sealing rings against the body and the valve plug. Flexible disc springs automatically assure a tight seal by exerting pressure on the valve sealing rings, keeping them compressed. Opening and Closing the TVS Isolation Valves The isolation valve begins to stop flow when the valve plug enters the lower valve sealing ring. When the isolation valve is completely closed, the valve plug is in contact with the full height of the valve sealing rings, ensuring the best possible seal. In fact, there is no advantage to be gained in torqueing the valve closed. Armstrong recommends that after closing the isolation valves completely, the handwheel should be turned back one half turn. This makes it easy to re-open the valve by avoiding metal to metal seizure. Troubleshooting – Isolation Valves A piston valve will retain its leak tightness for several years without maintenance. In severe service, such as rapid heating and cooling, some field maintenance may be required. Depending on the problem, these simple steps may help: ! ! ! ! ! Isolation Valve leaks, when the valve is closed . First, Check to make sure the valve is actually closed . Check to see if bonnet is seated on the body, if not, tighten the bonnet nuts until the bonnet seats. This recompresses the valve sealing rings against the body and the valve plug. If valve continues to leak, replace the isolation valve assembly

Incoming search terms:

TVS TANK VENT SCRUBBER INSTALLATION, OPERATION And MAINTENANCE MANUAL

0

Filed Under (TVS) by admin on 27-10-2010

download
INSTALLATION 2.1 Initial Setup After receiving the TVS, remove the packaging materials. Remove the wooden skid secured to the base of the unit and inspect all parts for damage. If any parts are damaged contact shipping company to file claim for damaged equipment. Select a location for the unit where adequate service clearance is provided for replacing the media in the unit. The media is removable from either the top, or the 150 mm port located on the side of the unit. Ample clearance (about 0.5 meters) should also be provided for space for media removal by vacuum. (This may be provided by others). 2.2 Electrical Connections (Optional) An electrical wiring diagram may be necessary and included with these instructions. 230/460 volt, 3 phase systems require a motor starter and disconnect. Refer to the wiring diagram for proper wiring connections. Check for proper motor rotation before operating the unit. All external wiring must be in accordance with National and Local Electrical Codes. Pay particular attention to proper grounding of the unit. 2.3 Media Bed Fill the Tank Vent Scrubber as follows: NOTE: Gloves and a dust mask should be worn when handling media. See MSDS sheet for proper handling requirements. 2.3.1 Remove the cover by loosening the bolts on top of the unit. 2.3.2 Inspect the interior of the tank to be certain it is empty. 2.3.3 Close and secure vacuum discharge port. 2.3.4 Select the correct media type and load the tank to a depth of 610 mm. 2.3.5 Replace the cover by securing the bolts on top of the unit. After 48 to 72 hours of operation, open cover and check media level for settlement. Media level must be 152 mm below lip of tank to reach proper fill requirement. Add media as required

Incoming search terms:

Yamaha V-Star 1100 Needle/ Jet Kit REMOVAL AND INSTALLATION MANUALS

0

Filed Under (Honda) by admin on 27-12-2011

download
To install this needle and jet kit: • Remove carburetors from the engine per Yamaha shop manual procedures. Note: Always perform internal carburetor work in a clean area. • Remove the vacuum slide from each carburetor. • Remove the OEM needle, spacer and washers, noting order of assembly. (Note; the washers are used as shims to raise the needle, each is equivalent to ½ clip position, use these to fine tune the needle) • Counting from the top to the bottom, install the new Baron needle clip on groove #4 of the replacement Baron adjustable needles. The top is the blunt end of the needle. • Reinstall the OEM spacer and washers as shown in the figure below. • Reinstall the vacuum slides along with the diaphragm spring and reattach the diaphragm covers Note: Verify that the slides maintain their full range of movement! • Drain the fuel from the float bowls and remove the bowl covers. • Remove the OEM main jets and replace them with Baron’s supplied Mikuni main jets. Install the “base setting” main jets as indicated above. NOTE: V-Star 1100 carburetion runs staggered jetting! Make sure the front cylinder’s carburetor gets the larger main jet (numerically), and the rear cylinder’s carburetor gets the smaller main jet . Important! Extra jets have been included in your kit. These will help you fine-tune the carburetors for changing conditions. These conditions include climate and weather patterns in your area as well as exhaust equipment on your motorcycle. Barons determines the jet and clip recommendations that best suit your average riding conditions based upon information supplied to us at the time of your order. Changes in weather, altitude or modifications to your exhaust system may require jets other than those supplied. • Thoroughly clean the inside of the float bowls prior to reinstalling them. 311 #1 Industrial Way – Fallbrook, CA 92028 – USA Phone: (760) 731-1200 Fax: (760) 731-1284 E-mail: tech@baronscustom.com Website: www.baronscustom.com Included in this kit: (4)Mikuni main jets #107.5, 110, 112.5, 115, (2) titanium needles, (2) clips, (8) cap-head allen screws Tools required: 3-4-5 mm allen wrenches, 10&12 mm sockets, 10mm end wrench, phillips & flat screwdrivers, pliers, drill. Revision 4.0 • Reassemble the carburetors by reversing the order of above steps. Use the new supplied cap head Allen screws in place of the OEM Phillips head screws for the float bowls. • Locate the fuel mixture screws – they will either be a screw head or a brass plug. If it is a screw head, skip to step c . If you see a brass plug with a small hole in the center, proceed as follows: a. With a 5/32″ drill bit, carefully and slowly drill through the fuel mixture plugs

Incoming search terms:

Hot-Start Kit For Yamaha YZ/ WR 400F

0

Filed Under (Yamaha) by admin on 16-12-2010

download
Blaster Rear Brake Kits 121-01298 • YFS200 Blaster ’88-’98 • This cable will eliminate the stock cable from the handlebar. Cable will go from the rear brake pedal to the caliper. 121-01299 • Same as 121-01298 +4″ • Cable is 4″ longer for extended swingarms. 121-01027 Replacement Ratchet Spark Plug Wrench 121-08147 • Designed specifically to fit where there is limited space • Ratchet mechanism works one way • Fits standard 13/16″ plugs
INDEX PAINT HANDLEBARS STREET LEVERS FORK SEALS CABLES SUSPENSION ELECTRICAL FILTERS BRAKE LINES BRAKES CABLE MAKING SUPPLIES CONTROLS DUAL SPORT MANUALS FSO PRODUCTS EMGO DRIVE DISPLAY JETS BEARINGS EYEWEAR VINTAGE MIRRORS EUROPEAN KICKERS SHIFTERS MISC HARD PARTS SHOP TOOLS CHEMICALS TOOLS R . 03-15-06 21 (626) 792-7384 www.FlandersCompany.com Fax: (626) 792-5341 www.FlandersCo.com Specialty Tools Swingarm Bearing Tool 121-080213 • Designed for installation of the swing arm bearings on late model Japanese motorcycles • Using the correct size insert (various sizes included in kit) and the puller, the mechanic can draw the bearing into the swingarm without beating on it with a hammer Main Jet Wrenches • High-quality die cast construction • 6mm round and hex jets and 8mm round • Cap holds a few spare main jets • Sold each 121-08023 6mm Hex (Fits 6mm hex main jets) 121-08024 8mm Round (Fits 8mm round main jets) 121-08025 6mm Round (Fits 6mm round main and pilot) Allen Extension 121-080184 • 5mm allen on a 6.25″ long, 3⁄8-drive extension for hard-to-reach case bolts • Designed for use with air tools • Great for splitting engine cases

HARLEY-DAVIDSON Starter Relay Location Guide

0

Filed Under (Harley Davidson) by admin on 18-04-2012

download
Touring 1998 – 2007 Additional Notes: Relay Location: Under Seat in rubber Boot Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: FULL SIZE Factory Relay Part #: 31504-91A Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-1 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 ***2004 – 2007 FLHR series bikes & 2007 FLHX require additional Adaptor AD-1 & DGD-1. Start Relay is in Power Distribution box. Replaces H-D Relay part# 31579-04 Softails 2000 – 2007 Additional Notes: 2000 is when the Softails changed to Twin Cams. Relay Location: Under Seat in covered Power Distribution Box. Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Softails 1996 – 1999 Additional Notes: Relay Location: Under Seat in covered Power Distribution Box. Battery Connection: Under Seat,Visiable Installation Notes: No Access Issues Factory Relay Type: FULL SIZE Factory Relay Part #: 31504-91A Connection Type: Ground Lug to Battery + Terminial System Relay Replacement: R-S-1 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05
Dyna 2007 Additional Notes: Relay Location: Under Side Panel Cover. Battery Connection: Replace Batt 15A Fuse with Supplied Fuse Holder Installation Notes: No Access Issues Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Tap 12v Fuse (Batt 15A) System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Dyna 2000 – 2005 Additional Notes: Relay Location: Under Side Panel Cover. Battery Connection: Battery connection is made direct to Battery Buss to right of Relay * see Pic3 Installation Notes: Remove Outer Cover, then Remove 4 bolts holding secondary protector plate in place. Relay is on the upper left. Factory Relay Type: 1/2 SIZE Factory Relay Part #: 31522-00B Connection Type: Ground Lug to Battery Buss + Terminial System Relay Replacement: R-S-3 Circuit: Cold C Copywrite 2005 Identity Inv. LLC As of: 11.05 Pic3 Sportster 2004-2007

Incoming search terms:

Harley Davidson Softail 1987 to Current Trike Conversion Installation Manual

0

Filed Under (Harley Davidson) by admin on 05-03-2012

download
Protect yourself and others when you have a vehicle up in the air. Anytime you lift a vehicle, either by hoist or a jack, make sure that it is securely supported. b. c. d. e. f. Make sure the engine is turned off before you begin work. • Carbon Monoxide poisoning from exhaust gases: Be sure there is adequate ventilation whenever you run the engine. • Burns from hot parts: Let the engine and exhaust system cool before working on those areas. • Injury from moving parts: If running the engine, keep hands, fingers and clothing away from moving/rotating parts. Gasoline vapor and hydrogen gases from batteries are explosive. To reduce the possibility of fire or explosion, be careful when working near gasoline and batteries. Use only nonflammable solvent, not gasoline, to clean parts Never drain or store gasoline in an open container. Keep all cigarettes, sparks or flame away from the battery and all fuel related parts. 1.4 Specifications Overall Length: 66″ Body Length: 92″ Wheel Base: 53″ Load Capacity: 620 Lb Tire Size (15″): 205 / 70 / R15 Wheel Size (15″) (4 lug) Offset +35 mm 15x7JJ 4×4.5 – (Current Installations – Alum Rear End) Wheel Size (15″) (5 lug) Offset +35 mm 15x7JJ 5×4.5 – (Later Installations – Black Rear End) Tire Size (16″) 215 / 60 / R16 Wheel Size (16″) (5 lug) Offset +40 mm 16x7JJ 5×4.5 – (First Installations – Black Rear End) Tire Pressure: 20 PSI Suspension: Internal Swing Arm utilizing OEM shocks Rear Differential: Custom-built rear differential utilizing OEM drive belt. Brakes: Original front plus 2 high performance disc brakes at rear. Storage Capacity: 3.75 cubic feet. 2 full-face helmets and additional storage

2009 GAS GAS TXT PRO TECHNICAL SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Gas Gas) by admin on 28-11-2010

download
ENGINE 2 stroke, single cylinder, direct reed valve crankcase induction. Liquid cooled. 125 cc. engine Cylinder size 124,8 cc. Bore and stroke 54 x 54.5 mm. 200 cc. engine Cylinder size 175,3 cc. Bore and stroke 64 x 54,5 mm. 250 cc. engine Cylinder size 247,7 cc. Bore and stroke 72,5 x 60 mm. 280 cc. engine Cylinder size 272,2 cc. Bore and stroke 76 x 60 mm. 300 cc. engine Cylinder size 294,1 cc. Bore and stroke 79 x 60 mm. Carburettor, diameter of the diffusor 26 Lubrication system Mixture (50:1)(2%) Ignition system Digital magnetic flywheel CDI TRANSMISSION Transmission type 6 gears, Four / Six system by GAS GAS* (Patented). Clutch type Hydraulic command, 1/3 discs, variable progressive with diaphragm system by GAS GAS* (Patented). Driving system By chain Gear ratio 1st. 2,996 (35x27x28/16x24x23) 2nd. 2,571 (36/14) 3th. 2,187 (35/16) 4st. 2,112 (36x23x24/14x28x24) 5st. 1,125 (27/24) 6th. 0,821 (23/28)
-11- Primary reduction ratio 2,777 (75/27) Final reduction ratio 3,818 (42/11) Overall drive ratio 8,704 (6th. gear) Transmission oil Capacity 550 cc. Type 10W40 API SF o SG. FRAME Type Tubular profile made with Cr-Mo. Tyres Front 2,75 x 21″ Trial Rear 4,00 x 18″ Trial tubeless. Suspension Front Adjustable tele-hydraulic fork ø 40 mm. (125 / 200). Adjustable tele-hydraulic fork ø 40 mm with aluminium bars (250 / 280 / 300) Rear Variable progressive system with mono-shock multiadjustable. Suspension stroke Front 177 mm. Rear 164 mm. Front fork oil SAE 5. Front fork oil level ø 40 mm.(125 / 200) 180 mm. air chamber steel bar ø 40 mm. (250 / 280 / 300) 160 mm. air chamber aluminium bar BRAKES Type Disc brake. Disc diameter Front ø185 mm. 4 piston calipers. Rear ø150 mm. 2 piston calipers. DIMENSIONS Overall height 1180 mm. Overall width 820 mm. Seat height 650 mm. Ground clearance 315 mm. Wheelbase 1330 mm. Fuel tank capacity 3,1 liters.

Incoming search terms:

Incoming search terms: