tvs victor gx motorcycle kickstarter assembly

You search Auto repair manual PDF tvs victor gx motorcycle kickstarter assembly, if there are search results will appear below. If search results do not exist, please search by others keyword.



  tvs victor gx motorcycle kickstarter assembly Direct Download speed 5282 Kb/s

  tvs victor gx motorcycle kickstarter assembly Full Version speed 6162 Kb/s



Vengeance Motorcycle Specification And Owner's Manual

0

Filed Under (Vengeance) by admin on 20-11-2010

download
Vengeance Maxis • Vengeance Raven • Vengeance Banshee • Vengeance Whiplash • Hotrod Drifter • Hotrod CalChop • Hotrod Teacher • Hotrod Bone Shifting Gears Starting off and changing gears requires coordination of the clutch and throttle and gearshift lever. If you don’t do things right, the amount of control you have over the bike is lessened. To start off, pull in the clutch, shift into first gear, roll on the throttle a little, and ease out the clutch. You will become familiar with the friction zone (that’s where the clutch begins to take hold and move the bike), and you add a bit more throttle. You don’t want to stall the engine, nor do you want to over-rev it. There’s a sweet spot in there; find it. Shift while traveling in a straight line. Shifting in a curve is not good practice, and something to be avoided. Become familiar with the sound of your engine, so you can tell when you should shift without looking at your instruments. When you downshift to a lower gear, you should (in one swift, smooth movement) be able to squeeze the clutch, rev the engine a little to let it catch the lower gear smoothly, and shift down. When you come to a stop in traffic, leave the bike in first gear with the clutch disengaged (just in case you want to accelerate out of there in a hurry). Who knows what may be coming up behind you. Braking Don’t ever forget: The front brake on your motorcycle can supply as much as 70 percent or more of your stopping power. The single most important thing you can learn about braking is to use that front brake every single time you want to slow down. Turning When you are riding along the road, you lean a motorcycle into a turn. Learning to lean is an essential part of riding a motorcycle. It is a normal function of the bike when you are changing its path of travel – and quite different from turning the steering wheel of your car. To get the motorcycle to lean in a normal turn, press the handlebar in the direction of the turn and maintain slight pressure on that handlebar to take you smoothly through that particular turn. In other words: press right to go right; press left to go left. Your instincts to keep the motorcycle on a smooth path while keeping it from falling over usually take care of this without you even noticing it. (Demonstrate to yourself how a motorcycle moves by pressing a handlebar slightly while traveling in a straight line. The motorcycle will move in the direction of the handlebar you pushed.) • Slow down before you enter the turn; look as far ahead as possible through the turn. • Keep your feet on the pegs, and grip the gas tank with your knees. • Lean with the motorcycle; don’t try to sit perpendicular to the road while the motorcycle is leaning over. • Keep an even throttle through the turn, or even accelerate a little bit. Checking the Bike before the Ride It’s not fun to have things go wrong on a motorcycle, but if you spend a minute before you go off on a ride, you can increase the chances that nothing will.

Incoming search terms:

1999-2002 Indian Motorcycle Mirror Housing Removal and Replacement

0

Filed Under (Indian) by admin on 31-10-2010

download
1. Remove seat. 2. Disconnect battery. 3. Remove handlebar cover on top-center of handlebar. 4. Remove left-side clutch-bracket assembly. This exposes an access hole on the underside of the handlebar. 5. Pass the end of the Signal® mirror wires through one of the small holes located on the underside of the clutch-bracket assembly housing. 6. Take piano wire/fish tape and insert at the access hole located on the underside of the handlebar to the center of the handlebar (center handlebar cover removed). 7. Fasten the end of the Signal® mirror wires to the piano wire/fish tape and pull through the handlebars to the center opening. 8. Pull excess wire through the handlebars leaving approximately 2″ of extra wire at the mirror side. 9. Re-assemble clutch-bracket assembly allowing the Signal® mirror wire to wrap around the outside edge of the cover assembly into the underside access hole. Secure Signal® mirror with enclosed 1.5″ long 5/ 16 ” – 24 Allen head bolt. 10. Loosen throttle assembly side and slide back to expose access hole. DO NOT REMOVE THROTTLE ASSEMBLY. Proceed to pass the Signal® mirror wire through the handlebar at the opposite side and re-assemble the throttle assembly. 11. Run both sets of wires under the fuel tank along the topside of the frame to the battery compartment. 12. Connect both black wires to the enclosed ring connector for connection to the battery ground terminal. 13. Locate the male/female electrical connector that is located behind the battery. This wiring assembly is for your tail lamp assembly for braking and turning (see photo). 14. Make sure the harnesses are routed securely to the wire connectors and enough slack is left for splicing or soldering. Cut the heat shrink into (4) equal pieces (approx. 2″ each). 15. Slide the heat shrink over the passenger side Signal® mirror wire. Solder the Right Signal® mirror wire to the Brown wire. Slide the heat shrink over to cover the soldered area. Heat the shrink tube into place with a heat shrink gun or hair dryer. 16. Repeat sliding the heat shrink over the driver side Signal® mirror wire. Solder the Left Signal® mirror wire to the Purple wire. Slide the heat shrink over to cover the soldered area. Heat the shrink tube into place with a heat shrink gun or hair dryer. 17. Connect ground and positive battery connections. 18. Re-install seat.

Incoming search terms:

1300 Yamaha V-Star Installation Manual

0

Filed Under (Yamaha) by admin on 07-11-2010

download
1) Place motorcycle on a firm level surface and secure in a upright position. 2) Remove saddle bags and saddle bag hardware (Tourer model only) Also remove rear riders pegs (Tourer model requires removal of rear footpeg offset hardware as well) 3) Attach bracket A (right) / B (left) to rear footpeg attachment point using new bolts provided. Remount footpegs/saddlebag hardware over top of brackets A/B. NOTE: Do not attach leveling stand bracket at this time 4) Attach bracket C(right) / D(left) to rear fender sub frame using new bolts provided. (Tourer model only – Saddle bag hardware mounts to the outside of brackets C/D. Brackets C/D mount between chrome side rail and saddlebag hardware.) NOTE: Brackets C/D have welded spacers which attach in toward rear fender 5) Attach top of Bracket E(right) / F(left) to rear of brackets C/D. Brackets E/F mount to the inside of brackets C/D. NOTE: Use ½ inch spacer between brackets E/F and C/D on Tourer model ONLY
6) Attach rear of brackets A/B to TOP of forward hitch arms. Attach bottom to brackets E/F to rear hitch plate. 7) Carefully tighten all bolts at this time ensuring hitch is square with motorcycle. Hitch Bracket Identification Leveling stand screw jack installation 1) Attach leveling stand brackets to brackets A and B 2) Thread right side screw jack into threaded hole on leveling stand bracket attached to bracket A sand adjust leveling jack bolt out. 3) Push motorcycle over from left side until right screw jack is touching floor. 4) Thread left side screw jack into threaded hole on leveling stand bracket attached to bracket B and adjust out until motorcycle will rest upright on both screw jacks. 5) Adjust screw jacks until motorcycle is level. 6) After InstaTrike is attached to or removed from receiver hitch, be sure to remove leveling stands and leveling stand brackets. CAUTION – Use screw jacks to hold motorcycle upright and level ONLY. Do not lift motorcycle with screw jacks. CAUTION – Use care when installing screw jacks. Be certain that motorcycle is always in a stable balanced position.
INSTALLATION OF THE TOW-PAC HITCH CART. 1. Place your motorcycle on a smooth flat surface, like a garage floor, and install leveling stands. Install right leveling stand first. Carefully raise motorcycle off of side stand and install left leveling stand. Caution – Use leveling stands to level motorcycle ONLY. Do not raise motorcycle with stands Caution – Be certain that motorcycle is always in a stable balanced position when installing leveling stands. 2. Assemble the axles, tires and wheels, and fenders onto the tow- pac hitch cart. 3. Carefully align the tow-pac hitch cart’s hitch mount with the receiver hitch on the motorcycle. Now push the hitch mount into the receiver hitch. (this might be a little difficult until you get use to doing it. Removing the paint from the hitch mount and applying a little grease will help.) 4. Place the hitch pin through the receiver hitch and hitch mount ( alignment plate ). Install and tighten the tension bolt

Incoming search terms:

Motorcycle LED lights RENEGADE LIGHTS Disconnection Guide

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Make sure your bike is cool and parked on a flat secure surface! 2. Find your battery (you may have to remove your seat or side covers in order to get to your battery) Disconnect the NEGATIVE ( -) cable. Negative battery cable must be disconnected from the battery in order to avoid safety hazards! Be sure as you disconnect the Negative cable that it does not touch or make contact with your Positive terminal 3. Disconnect the fuse holder from the battery – both the positive ( +) and negative ( -) sides. 4. Cut the wire to the light that is not working with the side cutters. 5. At the problem light twist the light case back and forth slowly and then pull firmly, DO NOT yank to remove from the motorcycle. 6. If the motorcycle led light does not come off easily, repeat the twisting motion back and froth until you feel the light loosen – then pull. 7. Pull the motorcycle led light away from the motorcycle slowly until the cut end of wire falls free. 8. If you will NOT be using your motorcycle until the new lights arrive, you may stop at this step. SAFETY POINT: Otherwise, where you cut the wire, you need to dead end or tape the cut wire. This will keep it from shorting out until the new motorcycle led light is installed. 9. Reconnect fuse holder to battery. 10. Reconnect the battery and then install the seat. 11. Return the motorcycle led light or lights to Renegade Lights along with Warranty Return Policy Form. 12. Renegade Lights will return your new motorcycle led lights along with instructions for installing them.

Incoming search terms:

Harley Davidson Softail Drive Side Brake System Installation Manual

0

Filed Under (Harley Davidson) by admin on 30-03-2012

download
Removing The Stock Components Although the PM Drive Side Brake System can be installed with the swing arm bolted to the frame, we recommend removing it for better access as well as repainting. Begin by removing rear wheel,stock brake components and belt guard from swing arm. Photo #1 Using supplied 3/4 x 2″bolt,position Drive Side BrakeAssembly on swing arm. Slide assembly to center position of tab and axle spans. Making sure brake mounting tabs are flush with swing arm,snug 3/4 x 2″ bolt to hold assembly and mark swing arm area to be ground Photo #2 . Remove entire assembly from swing arm and thoroughly grind paint away from marked areas Photo #3 . Photo #4 Re-mount assembly to swing arm and slide to rear-most position of both axle and brake mounting tabs. Confirm that brake tabs are flush with swing arm and parallel to each other. Snug 3/4 x 2″bolt and 5/16″socket head cap screws in tabs to hold assembly during welding process. Warning Center the motorcycle on the lift so that it will not fall while you are working on it. Photo #6 Photo #5 Photo #7 Photo #9 Welding Tabs to Swing Arm Note PM recommends all welding be done by a certified welder. Photo #5 Tack weld rear of tabs to swing arm. Avoid excessive welding near brake as- sembly as heat can mar finish. Loosen socket head cap screws and 3/4″bolt,Slide entire assembly to forward most position and re tighten bolts Photo #6 (movement should require minimal effort if tabs are aligned properly) and tack front of tabs to swing arm. Remove brake assembly from swing arm. Weld tabs to swing arm.Verify alignment of tabs, as they must remain parallel to each other. Repaint swing arm and re-install on bike to factory torque specs. Installing Brake Assembly Remove primary bracket from tower assembly (this allows bracket to be installed without having to line up caliper on disc) by removing the three 5/16″socket head cap screws (commonly called allen bolts). Photo #7 Mount rear tire and bolt pulley to rear wheel. Place disassembled bracket against pulley using smaller of two supplied spacers between bracket and pulley. Slide wheel/brake assembly into swing arm. Place large spacer on right side and slide axle in. Do not tighten axle at this point . Photo #8 Slide caliper/tower assembly over disc and install 5/16″x 1″socket head cap screw in center hole to position assembly Photo #9 . Snug, but do not tighten bolt at this point.

Incoming search terms:

Daytona 675, Street Triple Street Triple R Fitting Instruction

0

Filed Under (Triumph) by admin on 29-10-2010

download
remove the original gear selector rod from the motorcycle. Note: The ball joint and locknut on the transmission linkage have a left hand thread. This is identified by either a machined ring on the gear selector rod on Daytona 675 or on the ball joint on Street Triple and Street Triple R. 1. Front ball joint 2. Locknut 3. Gear selector rod 4. Machined ring, left hand thread identification 5. Machined ring, left hand thread identification (StreetTriple and Street Triple R) 6. Remove the front and rear ball joints and front locknut only from the gear selector rod. Retain the locknut and both ball joints for re-use. Retain the gear selector rod if the motorcycle is to be returned to its original condition. 7. Remove the plastic end caps from the quickshifter assembly. 8. Screw the locknut on to the rear of the quickshifter assembly (right hand thread) leaving 8mm of thread exposed. 1. Quick shifter assembly 2. Locknut 9. Screw the rear ball joint (right hand thread) on to the rear of the quickshifter assembly until it contacts the locknut. Unscrew the ball joint, only enough to achieve the correct orientation in relation to the quickshifter cable, as shown below. Finger tighten the locknut at this stage. 1. Ball joint 2. Quickshifter assembly 3. Locknut 4. Quickshifter cable 10. Fit the locknut and front ball joint (left hand thread) to the front of the quickshifter assembly Screw the locknut and ball joint on to the quickshifter assembly to achieve a dimension between the ball joint ends of 203.5 mm. Ensure that the ball joint is in the correct orientation to the quickshifter cable, as shown below. Finger tighten the locknut at this stage. 1. Ball joint 2. Quickshifter assembly 3. Locknut 4. Quickshifter cable 12. Route the quickshifter cable through the gear selector rod aperture in the frame, as shown. 1. Quickshifter cable 2. Gear selector rod aperture 13. Locate the quickshifter assembly in position, through the frame with the sensor at the rear and the cable at the top. 1. Quick shifter assembly 2. Sensor 14. Attach the front ball joint to the transmission linkage. 1. Ball joint 2. Transmission linkage

Incoming search terms:

MC 1200 Motorcycle Trailer – 1200 lbs Assembly Instructions

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
Tongue: Remove tongue assembly from the frame bundle. Insert into the tongue channel and slide into the front cross member of the frame. Secure with two (2) 3/8″ X 4″ carriage bolts and 3/8″ flange lock nuts. Tighten. Thread the tongue wire harness through the front top hole in the tongue and pull out the hole provided in the left side of the tongue towards the rear. Connect to the frame harness with the plugs provided. Install grommets. Safety Chains: Insert a 3/8″ X 1-1/4″ hex bolt into a 3/8″ flat washer, safety chain and then through the lower hole on the front of the tongue. Place on a 3/8″ flat washer on the inside of the tongue and secure with 3/8″ flange lock nuts. Repeat procedure on the opposite side of the tongue. Tighten. Coupler: Mount the coupler onto the tongue with a 1/2″ X 4″ hex bolt trough the rear mounting holes of the coupler. Using two (2) 1/2″ X 1″ hex bolt attach the coupler to the tongue using the front mounting holes. Secure with flange lock nuts. Tighten. Axle: Attach the spring busing in the rear spring shackles with 1/2″ X 3- 1/4″ hex bolts and 1/2″ flange lock nuts. Position the axle under the trailer with spring eye to the front of the trailer. Slip the flat end of the spring in the rear spring shackle above the bushing just installed. Secure the front spring eye to the front spring shackle with 98/16″ X 3-1/4″ hex bolts and 9/16″ hex lock nuts. Tighten. Mount the tire and rim assemblies to the axle assembly with 1/2″ lug nuts and tighten to 80-90 ft./lbs. of torque using the rotation pattern as shown in the Shore Land’r Owners Manual . Retorque the lug nuts after 50 miles of driving and then periodically thereafter. Ramps: Locate the loading ramp. Note that one end has two holes punched in the bottom of the channel. (See parts drawing) Insert a 3/8″ X 1-1/2″ full threaded carriage bolt into one of these holes. Secure in this position using a 3/8″ flange lock nut. Tighten Place a second 3/8″ flange lock nut onto the same bolt only until the threads of the bolt are exposed through the nut locking it in

HONDA 2005 CBR 600 RR FULL S/S EXHAUST HEADER INSTALLATION

0

Filed Under (Honda) by admin on 01-12-2011

download
Place the motorcycle in a vise or on it’s kick stand and make sure it is safe and secure. NOTE: If reusing the stock midpipe and muffler, skip ahead to step #5. 2) Remove the rider and passenger seats. Unplug the tail light, license plate light, and turn signals wires inside the tail section. 3) Remove the four bolts that secure the tail section to the subframe. Carefully remove the tail section from the subframe. 4) Remove the four bolts that secure the license plate/turn signal mount to the subframe. Remove the mount from the motorcycle. 5) Remove the upper and lower front fairing pieces. 6) Remove the two bolts that attach the right side footpeg assembly to the motorcycle. Disconnect the rear brake light switch and swing the footpeg assembly out of the way. Remove the outer plastic foot guard. Remove the aluminum heat shield from the motorcycle. 7) If equipped, remove the o2 sensor from the stock midpipe assembly.
NOTE: If reusing the stock midpipe and muffler, loosen the midpipe mounting bolts, and loosen the clamp securing the headpipe to midpipe connection. Skip ahead to step #9 8) Remove the midpipe mounting bolt, located on the right side of the subframe. Remove the
muffler mounting bolts. Lower the muffler and remove the rear exhaust section from the midpipe. 9) Remove the eight hex flange nuts securing the header flanges to the cylinder. 10)Remove the bottom header mounting bolt from the midpipe assembly. Remove the complete header from the motorcycle. 11)Remove the hat washer and rubber grommet from the stock midpipe assembly. Install the rubber grommet and hat washer into the hole provided on the Jardine midpipe assembly. 12)Slide the four headpipes into the new collectors. The headpipes are numbered from #1 thru #4, with #1 being the furthest toward the left side of the motorcycle, then work your way to the right. Do not install the provided springs at this time

AIR / HYDRAULIC MOTORCYCLE LIFT REMOVABLE INSPECTION PLATE

0

Filed Under (Tips and Review) by admin on 19-11-2010

download
For best service, you should incorporate an oiler, regulator, and inline filter, as shown in the diagram on the next page. Hoses, couplers, oilers, regulators, and filters are all available at Harbor Freight Tools. NOTE: If an automatic oiler is not used, put 3-5 drops of pneumatic Tool Oil (not included) in the Motorcycle Lift’s Quick Coupler (38A) before each use. (See Figure B, next page.) To Check The Level Of Hydraulic Oil: 1. The Motorcycle Lift already contains some hydraulic oil in its Hydraulic Pump Reservoir (32P). Even so, it is recommended that you check the oil level in the Reservoir and, if necessary, top off the Reservoir with the proper amount of 15/40 hydraulic oil (not included). (See Assy. Diagram, page 15.) 2. Make sure to screw the two Adjusting Screws clockwise enough to lift the two Caster Wheels (14) off the floor so as to provide stability for the Motorcycle Lift. (See Figure A.) 3. To check the level of hydraulic oil, remove the Sliding Plate (36) from the Platform (35) to expose the Hydraulic Pump Reservoir (32P). (See Assy. Diagrams, pages 13 and 15.) 4. Remove the rubber Filler Plug (33P) located on the top of the Reservoir (32P). If necessary, top off the Reservoir with hydraulic oil. (See Assy. Diagram, page 15.) 5. Connect the air compressor’s hose to the to the Air Motor assembly. Then turn on the air compressor and set its regulator at 120 PSI. (See Assy. Diagram, page 14.) 5. Insert the Lift Foot Pedal (11) onto the Pump Piston Spindle (9), and slowly pump the Lift Foot Pedal until a slight amount of hydraulic oil begins to leak out of the Reservoir (32P). Discontinue pumping the Lift Foot Pedal. Then, replace the Filler Plug (33P) on the top of the Reservoir. (See Assy. Diagram, page 15.) REGULATOR OILER FILTER TO QUICK COUPLER (38A) OF MOTORCYCLE LIFT FIGURE B 6. Insert the Release Foot Pedal (10) onto the Release Valve Spindle (5). Pump the Lift Foot Pedal (11) until the Platform (35) of the Motorcycle Lift reaches its maximum height. Then press down slightly on the Release Foot Pedal until the Platform is fully collapsed to the floor. Repeat this procedure several times to ensure the Motorcycle Lift is operating properly. (See Figure E, page 10.)

Incoming search terms:

Motorcycle LED lights RENEGADE LIGHTS Installation Guide

0

Filed Under (Tips and Review) by admin on 29-01-2011

download
1. Make sure your bike is cool and parked on a flat secure surface! 2. Find your battery (you may have to remove your seat or side covers in order to get to your battery) Disconnect the NEGATIVE ( -) cable. Negative battery cable must be disconnected from the battery in order to avoid safety hazards! Be sure as you disconnect the Negative cable that it does not touch or make contact with your Positive terminal 3. Your new motorcycle LED lights are polarity sensitive–meaning that the RED wires on the LEDs must be hooked to the Positive (+) terminal and the BLACK wires must be hooked to the Ground (-) . All Red Wires must go to a common power wire and ALL Black Wires must go to a common ground. You cannot run the LED motorcycle lights in a series nor can you run the wires from one motorcycle LED light to another in a loop type installation. ( All of the wires on the motorcycle LED lights which you install will end up together in one place at your battery.) 4. Pick a hidden flat surface around the front of your seat area to mount the switch. ( You must be able to reach the switch when the seat and/or side covers are back on your bike.) You will install your switch later using the double-sided tape provided to you. 5. Next, begin choosing the locations where you would like to mount your motorcycle LED lights. Choose areas which will give you the most light coverage overall, but which will allow the motorcycle LED lights itself to be hidden from easy view when you are standing back and looking at the bike. 6. Clean each area where you choose to place a motorcycle LED light with the alcohol based cleaner making sure all dirt and/or oil is removed from that area

Incoming search terms:

Incoming search terms: