tw200 lowering

You search Auto repair manual PDF tw200 lowering, if there are search results will appear below. If search results do not exist, please search by others keyword.



  tw200 lowering Direct Download speed 5282 Kb/s

  tw200 lowering Full Version speed 6162 Kb/s



Kawasaki KLR Lowering Kit Installation Instructions

0

Filed Under (Kawasaki) by admin on 01-12-2010

download
locate the OEM tie rods (circled in yellow, in the picture below), and the rear shock absorber snubber (circled in red, in the picture below). Notice that there is a tie rod on each side of the motorcycle. These tie rods are secured by two long bolts that pass first through the LH tie rod, then through the suspension, and finally held in place by two 17mm nuts on the RH side. Loosen these two 17mm bolts, and prepare them for removal. It helps to raise the rear tire just slightly with a jack or by a helper, to take the load off of these 17mm bolts. Below is another picture, better exposing the orange rubber snubber on the lower shock absorber rod… This is where the snubber spacers are installed, but don’t do it just yet…there’s more info on this later in the instructions. 3. Remove the 17mm nuts from the tie rods, keep the weight off of the rear wheel, and remove the upper and lower bolts from the tie rods. The rods are easily removed at this point. Take notice that the LH rod has recesses in each end, where the heads of the 17mm securing bolts fit. 4. Replace the tie rods with the new Scootworks tie rods in your kit. Install the tie rod with the recessed bolt holes on the LH side, with the recesses facing outward. Re-install the bolts from the LH side, through the LH tie rod, through the suspension, and through the RH tie rod. Secure them with the original nuts, and torque to 43 ft/lbs. The recessed bolt holes in the LH tie rod are seen in the picture of the Scootworks KLR tie rods below… 5. Do not install the plastic snubber spacers at this time. Lower the rear of the bike and remove the frame from the lift or jack stands. The rear lowering is completed. Sit on the motorcycle and determine if you’ve lowered it to a satisfactory level. If not, proceed to step #6. Your Scootworks KLR Lowering Kit is now installed. The following information is supplied as a supplement, to allow you to complete the job of lowering your bike that you’ve begun by using this Quality Scootworks product. NOTE: Be sure to check the chain tension after installation of the lowering kit, and adjust as necessary. Tips for setup and use of your lowering kit BE SURE to read the FAQ at the end of this document, for tips, warnings, and adjustments for your new lowering kit! Lowering the Front of your KLR-series Motorcycle

Incoming search terms:

Kawasaki Vulcan Front Suspension Lowering Kit Installation manual

0

Filed Under (Kawasaki) by admin on 27-02-2011

download
INSTALLATION 1. This lowering method requires replacement of the front spring spacers. This is a simple task, and is completely reversible. First, raise the front tire off of the ground before you begin. Raise the motorcycle so no weight is applied to the front wheel. 2. Cover the gas tank with a thick towel to prevent scratching. Don’t omit this…you’ll be sorry if you do! 3. If the handlebar risers are OEM (stock), loosen the handlebars in their clamps and lift them from the risers, carefully placing them on the gas tank on a thick towel to prevent scratching. This will allow room for the spring spacers to be removed from the front forks. 4. Using a small knife blade, sharp screw driver, etc. in the pinch grove on each side of the triple clamp, gently pry upwards and pop the chromed plastic covers off. These are the covers on the top of the front forks, covering the spring retainers. Below these chrome caps, you’ll find a gold anodized metal plug with a small counter bore in the center. This is the part used to retain the springs within the front fork tubes. Using an extension bar, large Phillips screwdriver, etc., press down a bit in the counter bored area of the plug to take the pressure off of the small internal “C” ring. While this “gold” colored plug is depressed, remove the internal C-ring. The C-ring is made of small diameter wire. Once the C-ring is removed, slowly release the pressure on the plug and it’ll push itself out of the top of the shock. The picture below is of the upper fork leg with the gold retaining plug removed. 5. Stick a finger into the fork tube, and slide the OEM tubular spacer up and out of the fork tube. 6. The picture below illustrates the use of a Scootworks lowering spacer with the fork spring. On the right hand end of the you’ll see a Scootworks lowering spacer. The fork spring stays in the front fork, and you’ll drop in the spacer with the desired amount of lowering. The approximate amount of lowering is marked on each Scootworks spacer. 7. Select the spacers for the desired amount of lowering. The longest spacers supplied are marked as [1] and will lower the front suspension 1″. The spacers of middle length are marked as [2] and will lower the front suspension by 2″. The shortest spacers supplied in the kit are marked as [3] and will lower the front suspension by 3″. Omission of the spacers completely will lower the front suspension by approximately 4″. 8. Install the selected spacers in the fork tubes, on top of the internal fork spring. Place the gold anodized metal plugs on top of the spacers and press them back into the fork tube. Be sure to turn the metal plug so the side with the counter bore is facing outwards. Reinstall the C-rings, and gently lower the front end back to the ground. Make sure the C-rings seat themselves in their respective grooves when the weight of the bike is placed back on the front end. Re-install the chrome caps.

Incoming search terms:

YAMAHA ROADSTAR/ WARRIOR ADJUSTABLE REAR LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 16-01-2012

download
Secure motorcycle to a bike lift and raise the motorcycle. Rear wheel should remain barely resting on the ground. 2. See diagram on page 2 for references made in parentheses, for example (#5). 3. Remove the nut from the rear suspension bolt (#5) at the bottom of the shock (#7). You may need to remove your exhaust and rear horn to access the nut and bolt. 4. Remove this suspension bolt (#5) from the non-exhaust side of the bike. You may need to raise or lower the bike to ease the tension on the bolt in order for it to come out. 5. Next remove the nut (#4) and bolt connecting the relay arm (#3) to the swingarm. From here remove the entire shock assembly and relay arm from the bike. For ease of re-installing the relay arm (Step 8) and shock be sure to take precautions that in removing the assembly, you can put it back the same way you took it off. Flipping of the relay arm can cause serious damage to the lowering kit and surrounding components. 6. Remove the two suspension arms from the relay arm(#3) and shock(#7). Compare stock arm to length of lowering arm you are about to install. Make sure the length of the lowering arm matches the link of the stock arm. To set how much you want to lower the bike, lengthen the lowering arms. Every 1/4″ longer than stock is approximately 1″ of drop. Do not lower the bike more than 2″ for safety reasons. To adjust, unscrew the large hex shaft from the threaded rods. Make sure to adjust length equally on both shafts. Be sure to tighten all jam nuts once desired lowering position is set. 7. Re-assemble the lowering arms to the top of the shock (#7) using the supplied collar, nut, and bolt. The stock collar (#6), the one in the eyelet at the top of the shock (#7), will need to be removed as it is too long. (This is because the heims are thicker than the stock arms) Do not tighten the nut, or re-install into the frame yet. 8. Re-install the relay arm (#3) to the swingarm. The large hex shafts go to the rear of the bike. This is where it

Yamaha Rear Suspension Lowering Kit installation Manual

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. This lowering method requires replacement rear suspension coupling components. This is a simple task, and is completely reversible. In addition, this kit provides for a 0″ setting, to easily return your bike to its original height. First, raise the rear tire off of the ground by the frame before you begin. Raise the motorcycle so no weight is applied to the rear wheel, allowing the rear wheel to spin freely. 2. Next, become familiar with your lowering kit. You’ll notice that there are two corners of the lowering component with two holes each, and one corner with a single hole. The corner with the single hole attaches to the swingarm (the bolt that is closest to the rear wheel). The only important part of this familiarization process, is to make sure that you get the part oriented in the correct position. The following photos will explain the purpose of the different holes, and also help you turn the part in the correct position before you install it. Look at the first photo on the next page: In the photo above, the part is positioned just as it should be, for installation on the left-hand side (kickstand side) of the motorcycle. A quick measurement will show that Dimension “A” on Side “A” should be shorter than Dimension “B” on Side “B”. If not, flip your part over (turn the face you are viewing away from you, but keep the corners with two holes on your left), and measure again. Next, study the photo below for info on the different heights you can set your bike to… When installed, Hole “0″ will place the bike at it’s original height. Placing the top bolt in Hole 1, and the bottom bolt in Hole 0, the bike will be lowered approximately ¾”. Placing the top bolt in Hole 1, and the bottom bolt in Hole 1, the bike will be lowered approximately 2″. Simple, eh? Now, let’s move on to installation. 3. Below is a photo of the factory suspension coupling as installed in your motorcycle. This photo was taken from the LH side of the bike, to keep things in perspective with our previous photos. Loosen the three bolts holding the original suspension coupling, and remove. Be aware that the rear wheel will drop down when the bolts are removed, just so there are no surprises!

The Honda Ace/ Spirit 750 Lowering Kit from INSTATALLATION

0

Filed Under (Honda) by admin on 16-11-2011

download
The installation of the Scootworks Ace/Spirit Lowering Kit follows the same procedure as replacing the rear shocks. However, Scootworks wanted to assist you as much as possible with the installation process, and developed this instruction package. If there are any steps you feel need improvement in instructions, please email support@scootworks.com and specify the area you are having trouble with. Unpacking! The shipping container and contents must be inspected by the purchaser for damage to goods immediately upon receipt of goods, and a claim must be filed with the carrier if damage is discovered. The purchaser must contact Scootworks within 24 hours from receipt of damaged goods to file a claim, and for further instructions. Your Scootworks Ace/Spirit Lowering Kit will come packed with a left and right side lowering assembly, two large flat washers, two M8 x 1.25 hex head bolts, and these printed instructions

Yamaha V-Star 650 Rear Lowering Kit REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 18-10-2010

download
INSTALLATION PROCEDURE 1. Secure motorcycle to a bike lift and raise the motorcycle. 2. Remove stock rear shock from the motorcycle per standard Yamaha shop manual instructions. 3. Place the shaft of the shock in V” blocks and secure this in a vice or press, applying firm pressure to the V” blocks to trap the shaft so it will not turn. Unscrew the upper shock mount eyelet from the shaft. NOTE: The upper mount is a standard thread so you will rotate the mount counter-clockwise to unscrew it. 4. Next, screw the New LA Choppers Shock Mount onto shock shaft using Loctite. 5. Re-install shock spring, making sure it is locked in place with the retaining ring prior to slowly releasing the spring compressor. Allow shock spring to expand against the retaining ring and machined washer. 6. Reinstall shock onto the motorcycle per standard Yamaha shop manual instructions. WARNING: Installing a lowering kit will decrease initial ground clearance. The motorcycle will be lower to the ground and care should be taken to avoid bottoming, especially over bumps or in turns. To maintain proper balanced geometry, the front and rear of the motorcycle should be lowered equally. Failure to properly install the lowering kit and operate the motorcycle after installation may result in serious injury or death to the rider. LIMITED GUARANTY: Because we cannot control the application of our products, buyer assumes risks for any and all damage caused to him or herself or any third party by virtue of any failure of these parts. Guaranty for such parts is limited to our replacement costs thereof. This guaranty is in lieu of all other guaranties or warranties express or implied, and all other such guaranties or warranties are hereby expressly disclaimed. By installation of these parts, buyer irrevocably agrees to the foregoing

2007-2008 Kawasaki ER6 and Ninja 650R Lowering Kit Installation Instructions

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Raise the motorcycle so the rear wheel is off the ground. As an example, you can use a motorcycle lift, two car jacks, or upside-down paint buckets placed under the foot pegs, but anything stable should do. ” Stable ” is the key word. Please take all precautions! 2) Using the 19 mm open wrench and the provided 8 mm hex wrench, loosen the button head bolt and locknut as shown This large washer will not be there on 2007 & 2008 models 3) Next, remove the locknut and the small washer from the back, and remove the button head bolt and the large washer from the front. You can pull out the button head bolt by slightly moving the rear suspension up and down at the same time. 4) 5) Lift the shock absorber and insert the spacer where the shock absorber was installed before. Note: The original bolt and washers (if any were on your bike) are not going to be used, but you should keep them for the future, in case you decide to uninstall the lowering kit. Slide over the main kit body and insert the provided hex head cap screw as shown Next, slide the provided hex head cap screw all the way through

HARLEY DAVIDSON SOFTAIL REAR LOWERING KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION Prepare the Motorcycle 1. Follow the Service Manual instructions to remove the seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect the negative (-) battery cable from the battery. 3. Place motorcycle on a lift and secure the front wheel. 4. Use an overhead crane or hoist attached to the frame to lift the rear of the motorcycle to allow the rear fork to pivot through its range of travel. 5. Place a screw jack under the rear wheel to support and adjust the rear fork during shock removal, installation and ride height adjustment. Be sure rear wheel is supported when removing rear shocks. If wheel is not supported rear fork can drop down, which could result in death or serious injury. (00481b) Removal 1. See Figure 1. Remove the bolt and washer (1) that fasten each of the shock absorbers (2) to the rear fork. NOTE Snap-on Tool Co. adapter, Part Number SRES 24, is necessary to gain access to the shock absorber bolts. 2. Remove the flanged locknut (6) and cup washer with grommet (5) fastening the shock absorber to the frame bracket (4) and remove the shock absorber. 3. Remove, inspect and, if necessary, replace the rubber grommets, the cup washers (5), and the bushing (3). 4. Repeat for the other shock absorber. Disassemble the Shock 1. Thoroughly clean the rear fork end of the shock, especially near the shock canister seal. 2. Support the rear fork end of the shock absorber and shock canister on the table of a press. 3. Press on the shaft to compress the spring in the canister until the keeper plate drops down away from the retaining ring.

Incoming search terms:

HAR:EY DAVIDSON FLHR/C/S (Road King) FRONT END LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 01-03-2011

download
Removal (Left and Right Forks) 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to Touring Model Service Manual and remove front wheel, fender and brakes. 3. Refer to Touring Model Service Manual and remove headlamp nacelle. 4. Loosen fork cap bolt from fork tube plug at top of fork tube, but do not remove. 5. See Figure 1. Standing at front of vehicle, loosen pinch bolt (with lockwasher) on right side of lower fork bracket, but do not remove. 6. Spray glass cleaner on fork tube above the rubber fork stop. After lubricating surfaces, move fork stop up fork tube until it contacts bottom of upper fork bracket. 7. Holding fork slider to prevent fork from dropping, remove fork cap bolt from fork tube plug. Slide fork tube down and out of upper fork bracket, fork stop, lower fork bracket and slider cover. 1 WARNING 1 WARNING 1 WARNING 1 of 5 ® Kit Number 54614-05 Figure 1. Loosen Pinch Bolt on Lower Fork Bracket i04808 1 Fork cap bolt 2 Fork stop 3 Pinch bolt 8. Thread fork cap bolt back into fork tube plug to prevent loss of oil while handling. 9. Move forks to bench area. Place suitable drain pan on floor beneath vise. 10. Repeat Steps 2-6 to remove left fork. Left And Right Fork-Disassembly 1. Remove nuts, lockwashers, flat washers and axle holder from studs at end of fork slider. 2. See Figure 2. Obtain FORK TUBE HOLDER (Part Number HD-41177) and proceed as follows: a. Clamp end of tool in vise in a horizontal position with plastic knobs facing toward you. b. See Figure 3. With the fork cap bolt topside, clamp fork tube between rubber pads on inboard side of tool. Tighten knobs until fork tube is securely held. 3. Remove fork cap bolt from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug from fork tube. Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove 6mm screw from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and discard damper tube. 12. Remove wear ring and rebound spring. Discard rebound spring. Do not expand or stretch retaining clip to remove from fork tube or clip may become bent or distorted. 13. Using pick tool, remove retaining clip between fork slider and fork tube. 14. Remove fork tube from fork slider. NOTE To overcome any resistance, use the fork tube as a slide hammer, that is, first push fork tube into fork slider and then pull it outward with a moderate amount of force. Repeat this sequence until fork tube separates from fork slider. 15. Slide fork oil seal, slider spacer and slider bushing off end of fork tube. Discard fork oil seal and slider bushing. 16. Remove the lower stop. Right and Left Fork-Assembly Exercise caution to avoid scratching or nicking fork tube. Damaging tube can result in fork oil leaks after assembly. 1. See Service Parts Illustration. Obtain new Damper Tube (Item 7, Part Number 46532-04) from kit. Obtain new Rebound Spring (Item 8, Part Number 46273-02) from kit and install on opposite end. Install wear ring removed in step 12. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube. Install lower stop at end of damper tube. 3. Install fork slider in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (14) (Part Number 45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing down fork tube. 5. Slide slider spacer down fork tube until it contacts slider bushing.

Incoming search terms:

HARLEY DAVIDSON TOURING FRONT LOWERING KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 02-03-2011

download
REMOVAL 1. Place suitable blocking under frame to raise front wheel several inches off the floor. For best results, use a hydraulic center stand on a level surface. 2. Refer to the appropriate Service Manual and remove the front forks. 3. Move forks to bench area. Place suitable drain pan on floor beneath a vise. INSTALLATION Fork Disassembly 1. See Figure 6. Remove nuts (U), lockwashers (T), flat washers (S) and axle holder (R) from studs at end of fork slider. 2. See Figure 1. Obtain FORK TUBE HOLDER (HD-41177) and proceed as follows: a. Clamp end of tool in vise (1) in a horizontal position with plastic knobs facing toward you. b. With the fork cap bolt topside, clamp fork tube between rubber pads (2) on inboard side of tool. Tighten knobs (3) until fork tube is securely held. NOTE Refer to Figure 6 for Steps 3-17. 3. Remove fork cap bolt (A) from fork tube plug. Remove quad ring seal. Save bolt but discard quad ring seal. 4. Using wrench flat, slowly unthread fork tube plug (B) from fork tube (G). Be aware that fork tube plug is under spring pressure, so have a firm grasp on plug as the last thread is turned. 5. Remove fork spring (1) from fork tube. 6. Remove fork assembly from fork tube holder. 7. Turning fork upside down, drain fork oil into drain pan. For best results, slowly pump fork tube and slider at least 10 times. 8. Install fork spring back into fork tube. 9. Place a shop rag on the floor, and turning fork assembly upside down, press end of spring against rag. While compressing spring to prevent rotation of damper tube, remove screw and washer (Q) from end of fork slider. Use air impact wrench for best results. 10. Remove and discard fork spring. 11. Remove and save blow valve (E). 12. Remove damper tube (2). 13. Remove rebound spring (F) from damper tube. 14. Using pick tool, remove retaining clip (H) between fork slider and fork tube. 15. Remove fork tube (G) from fork slider. Slide fork tube gently in a slide hammer motion against the slider to remove the seals and bushing from slider. 16. Slide fork oil seal (I), slider spacer (J) and slider bushing (K) off end of fork tube (G). 17. Remove the lower stop (L). Fork Assembly NOTE Refer to Figure 6 for the following procedure. 1. Obtain new Damper Tube (2) from kit and install rebound spring (F) over the lower end. 2. With the wear ring topside, slide new damper tube into fork tube, so that tube end drops through hole at bottom of fork tube (G). Install lower stop (L) on the lower end of damper tube. 3. Install fork slider (O or N) in fork tube holder. Slide fork tube into fork slider. 4. If necessary, obtain new slider bushing (K) (45940-84, not included). Coat slider bushing ID with clean fork oil. Slide slider bushing (K) down fork tube. 5. Slide slider spacer (J) down fork tube until it contacts slider bushing. 6. Obtain new fork oil seal (I) (45875-84A, not included). Coat fork oil seal ID with clean fork oil. With the lip garter spring side facing down (toward the fork slider), slide oil seal down fork tube until it contacts slider spacer title_tag=

Incoming search terms: