ultraglide sevice intravals

You search Auto repair manual PDF ultraglide sevice intravals, if there are search results will appear below. If search results do not exist, please search by others keyword.



  ultraglide sevice intravals Direct Download speed 5282 Kb/s

  ultraglide sevice intravals Full Version speed 6162 Kb/s



Harley Davidson Installing The Ride Time Ultra Progressive Tour Pak LED Tail Lights

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
Remove the light bulbs from the tail light housing by depressing the tab on the bulb socket assembly and turning counter clockwise. Remove the bulb from the bulb socket. 2. Remove the lenses from the warp-around light fixture. These lens are held in place by a non-hardening black sealant. In addition, there are three plastic alignment tabs on the lens body that clip into the lens frame. To remove the lens, insert the supplied push Stick through the hole in the back of the light bulb housing and gently but firmly push the lens outward. This action places a stress on the alignment tabs. 3 . Using a flat blade screw driver, pry the lens away from the frame at the top, side, and bottom to release the lens alignment tabs. Go back to step 2, and use the plastic tube to push the lens outward. It may be necessary to repeat the prying process and pushing process several times to remove the lens. Note: Some users have found it useful to heat the lens area with a hair dryer to soften the adhesive. Included in this kit are: Left and Right LED modules, 1 RTQC Quick Connect Accessory Cable , 2 RTV application sticks, 1 push stick, Approximately 3 inches of shrink tube, and 1 copy of instructions. Required for installation, but not included are: A tube of Permatex RTV (available at Wal-Mart), 1/8 inch drill bit, a drill, small flat blade screwdriver, other hand tools. Window/ body sealer if required to reseat lenses can be obtained at your local glass shop. Tour Pak, Harley Davidson, Electraglide, Raod King, and Ultraglide are registered trade marks of Harley David- son. Harley Davidson does not make or endorse the use of these lights. 4. When the lens begins to emerge from the frame, grasp it at the top and bottom and pull the lens from the housing using a up and down motion. Set the lens aside . Avoid having the sealant contact other surfaces. In most cases, the lens can be reinstalled without adding additional sealant . Note: Do not use RTV to reset the lens. If sealant is needed obtain a non-hardening body/windshield sealant from your local glass shop. 6. When you are comfortable with the location of the circuit board, drill a 1/8 inch hole in the back of the light housing. This hole will be used to bring the turn signal wire from the LED module into the Tour Pak. 7. Using the supplied stick, spread a thin layer of Permatex clear RTV silicone seal along the area where the circuit board will be located. Apply a similar layer to the top of the light housing. Route the turn signal wire through the 1/8″ hole and position the circuit board in the housing. Allow the RTV to cure. 5. Test fit the LED light board in the light housing.

BMW S1000 RR Rider's Manual

0

Filed Under (BMW) by admin on 28-11-2010

download
Standard status indicators Multifunction display 1 Speedometer 2 Coolant temperature 3 Clock (37) 4 Odometer and tripmeters (38) 5 Ride mode (43) 6 Gear indicator (20) Telltale lights 1 Flashing turn indicators, left 2 Flashing turn indicators, right 3 Idle 4 High-beam headlight Gear indicator The gear engaged or Nforneut- ralappearsonthe display. If no gear is engaged, the ‘neutral’telltale light also lights up. Service-due indicator If the next service is due in less than one month, the date for the next service is shown briefly after the Pre-Ride Check completes. Month 1 and year 2 are shown; in this example the read- ingmeans”August 2010″. 3 If the motorcycle covers long dis- tancesinthe course of the year, under certain circumstances it might be necessary to have it serviced at a date in advance of the forecast due date. If the countdown distance to the odometer reading at whichaservice will be due is less than 1000 km, the distance is counted down in steps of 100kmandisshown briefly after the Pre-Ride Check completes. If service is overdue, the due date or the odometer reading at which service was due is accom- paniedbythe’General’warning light showing yellow. The word “Service”remains permanently visible. If the sevice-due indicator appears more than a month before the service date, the date saved in the instrument cluster must be adjusted. This situation can occur if the battery was disconnected fora prolonged period of time. If you want to have the date set consulta specialist workshop, preferably an authorised BMW Motorraddealer. Standard warnings Mode of presentation Warnings are output byawarning light 1 or indicated byawarning string in the display.

BMW S1000 RR SPECIFICATION AND OWNER’S MANUAL

0

Filed Under (BMW) by admin on 12-11-2010

download
Status indicators If the motorcycle covers long dis- tancesinthe course of the year, under certain circumstances it might be necessary to have it serviced at a date in advance of the forecast due date. If the countdown distance to the odometer reading at whichaservice will be due is less than 1000 km, the distance is counted down in steps of 100kmandisshown briefly after the Pre-Ride Check completes. If service is overdue, the due date or the odometer reading at which service was due is accom- paniedbythe’General’warning light showing yellow. The word “Service”remains permanently visible. If the sevice-due indicator appears more than a month before the service date, the date saved in the instrument cluster must be adjusted. This situation can occur if the battery was disconnected fora prolonged period of time. If you want to have the date set consulta specialist workshop, preferably an authorised BMW Motorraddealer. Standard warnings Mode of presentation Warnings are output byawarning light 1 or indicated byawarning string in the display