undertail vins

You search Auto repair manual PDF undertail vins, if there are search results will appear below. If search results do not exist, please search by others keyword.



  undertail vins Direct Download speed 5282 Kb/s

  undertail vins Full Version speed 6162 Kb/s



Honda CBR 954 RR Undertail Kit INSTALLATION

0

Filed Under (Honda) by admin on 04-12-2011

download
Carefully remove the tail section body work. Save all bolts, washers and plastic rivets for re-installation of tail. Disconnect and remove the brake light (with all mounting grommets and washers), license plate and turn signals, key lock (with clip) and move all wiring out of the cutting areas. Remove the two bolts at the rear end of the stock fender (inside glove box) to allow the end to hang down for cutting.
2) Using a “Dremel” tool or cutting disc (this can also be done using a sharp edged knife, but is not recommended), remove the plastic shown in the photos to the above and below. Be sure to take your time cutting, so that you don’t cut away any more plastic than necessary. Honda CBR954RR Undertail Kit (2002-03, Available in: Honda Red, Gloss Black and Gun Metal) 3) *Install license plate brackets to back side of license plate as shown. Now hold license plate in desired location on undertail, carefully mark and drill holes, install using the two (2) sets of allen bolts and lock nuts. 4) Insert undertail left side first, then right side, be carefully not to crack
or scratch undertail. Use your stock plastic screw rivets to hold under- tail in place. Tighten all hardware on tail section, attach seat.
5) Using clips, splice your turn signal wires to the signals in the undertail. On the bike; the orange wire is the the left turn, light blue wire is the right turn and the green wires are the grounds. On the undertail the red wires are the power wires and the black wires are the ground. * After this modification your undertail is not returnable. Paint is not warrantied against paint chips, flaking or scratches from installation or rocks being thrown from tire into the tray. Need Help? If you need additional help with the installation of the undertail, go to www.hotbodiesracing.com and look for the “FAQs” link at the bottom of the home page. Most of your general questions can be answered on those pages. This installation does require a basic mechani- cal aptitude, if in doubt, contact your local motorcycle shop and have a professional mechanic perform the installation, 3 hours is the average installation time

Incoming search terms:

Kawasaki ZX14R Undertail Kit installation Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
This installation does require a basic mechanical aptitude, if in doubt, contact your local motorcycle shop and have a professional mechanic perform the installation, 1.5 hours is the average installation time. 7) Use supplied pop rivets to mount the undertail over top of the stock black trunk compartment and complete wiring of the LED license plate light. To connect the license plate light; use the stock black and yellow tracer wires with black undertail wire and stock red with red undertail wire. 6) Before installing the undertail, remove the adhesive back. Carefully clean the stock part where this adhesive will apply to. After you install the undertail with the rivets, press firmly and hold for 30 seconds. 8) After mounting undertail, re-install ECU and tool compartments. After re-installation of tool compartment re-install seat and seat cover, making sure all bolts and hardware are fastened securely. Your done! * After this modification your undertail is not returnable. Paint is not war- rantied against paint chips, flaking or scratches from installation or rocks being thrown from tire into the tray.

Honda RC51 2000-2005 SBK Undertail Kit INSTALLATION

0

Filed Under (Honda) by admin on 22-11-2011

download
Carefully remove the tail section body work. Save all bolts, washers and plastic rivets for re-installation of tail. Disconnect and remove the brake light (with all mounting grommets and washers), license plate and turn signals, key lock (with clip) and move all wiring out of the cutting areas. Remove the two bolts at the rear end of the stock fender (inside glove box) to allow the end to hang down for cutting Using a “Dremel” tool or cutting disc (this can also be done using a sharp edged knife, but is not recommended), remove the plastic shown in the photos to the above and below. Your subframe may be different but the cutting position is the same on all years. Be sure to take your time cutting, so that you don’t cut away any more plastic than necessary Replace all bodywork with fasteners loosely installed, mount undertail,
notice at bottom of the tray there are 2 holes, mark and remove tray, then drill holes in battery box 6) Inset lock into undertail using stock lock mounting clip, make sure the lock is in the correct position with the lock cable arm to function
properly. Insert undertail left side first, then right side, be carefull not to crack or scratch undertail. Use your stock plastic screw rivets to hold undertail in place. Attach lock cable to lock, check movement, adjust if necessary. Tighten all hardware on tail section, attach seat. * After this modification your undertail is not returnable. Paint is not war-
rantied against paint chips, flaking or scratches from installation or rocks being thrown from tire into the tray.
6) *Install license plate brackets to back side of license plate as shown. Now hold license plate in desired location on undertail, carefully mark and drill holes, install using the two (2) sets of allen bolts and lock nuts

Yamaha YZF-R1 Undertail Kit REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 11-01-2012

download
Carefully remove the tail section body work. Save all bolts, washers and plastic rivets for re-installation of tail. Disconnect and remove the brake light (with all mounting grommets and washers), license plate and turn signals, key lock (with clip) and move all wiring out of the cutting areas. Remove the two bolts at the rear end of the stock fender (inside glove box) to allow the end to hang down for cutting. 2) Using a “Dremel” tool or cutting disc (this can also be done using a sharp edged knife, but is not recommended), remove the plastic shown in the photos above and below. Be sure to take your time cutting, so that you don’t cut away any more plastic than necessary. 3) Now relocate the rear mounting holes for the glove box 1.25″ lower in the tray to raise it up in the subframe as shown. Yamaha YZF-R1 Undertail Kit (2000-01, Available in: Yamaha Red, Yamaha Blue) Need Help? If you need additional help with the installation of the undertail, go to www.hotbodiesracing.com and look for the “FAQs” link at the bottom of the home page. Most of your general questions can be answered on those pages. This installation does require a basic mechanical aptitude, if in doubt, contact your local motorcycle shop and have a professional mechanic perform the installation, 3 hours is the average installation time. * After this modification your undertail is not returnable. Paint is not war- rantied against paint chips, flaking or scratches from installation or rocks being thrown from tire into the tray. 5) *Install license plate brackets to back side of license plate as shown. Now hold license plate in desired location on undertail, carefully mark and drill holes, install using the two (2) sets of allen bolts and lock nuts

Honda CBR 600 F4i 2004 – 2005 Bestem USA Fiberglass F13 Installation Guide

0

Filed Under (Honda) by admin on 20-11-2011

download
We highly recommend having a professional install this undertail. A dremel tool or nsimilar is what we found the best to cut plastics. Place bike on a rear wheel center stand. Remove passenger seat and hardware which secure stock undertail section Unplug the harness that connects tail light and remove the stock undertail. Position Bestem undertail close to the bike and determine the amount of plastic needs to be cut out. Use a dremel tool to carefully trim off plastics (glove boxes etc). This is the most time consuming part of the installation but your patience will be paid off. 5) Once the new undertail is slide in, determine holes need to be drilled (only on
certain models). Reuse the hardware for the stock undertail to secure the new undertail. 6) The wiring color codes from two round tail lights are Black Wire – Ground, connects to Ground wire. Red Wire – Brake Light, connects to brake light. Blue Wire – Running Light, connect directly to the running light. Orange Wire – Turn Signal, connect them to your L/R turn signal wires We highly suggest you solder the connections and use heat shrink wrap to seal the connections. Test your lights before going out for a ride, also make sure your new undertail is securely installed on the bike. Now it’s time to go out for a spin!

Incoming search terms:

KAWASAKI Undertail Installation AND Removal instructions

0

Filed Under (Kawasaki) by admin on 26-04-2012

download
1- MASKING TAPE 2- DRILL 3- PHILLIPS SCREWDRIVER 4- HAND SAW BLADE OR DREMMEL 5- DRILL BIT # 3/16 (TABS – AREA NEAR LENSES ) 6- DRILL BIT # 15/64 (NYLON SCREW RIVETS FOR THE BACK) 7- ELECTRIC TAPE WHAT COMES WITH THIS UNDERTAIL? 2 RED LED BULBS 2 SCREWS REMOVE THE REAR SECTION OF THE BODY There are plastic body connectors as well as bolts inside the tail in addition to the Allen-head bolts on the outside surface. NOTE: KEEP YOUR STOCK RIVETS FOR LATER USE. REMOVE THE TAIL SECTION & SEAT REMOVE THE TAIL SECTION & SEAT REMOVE THE TAIL SECTION & SEAT REMOVE THE TAIL SECTION & SEAT REMOVE THE TAIL SECTION & SEAT REMOVE THE TAIL SECTION & SEAT

2004 – 2005 Camry, Highlander, And Solara, 2005 Matrix & Corolla PASSENGER AIRBAG INDICATOR LAMP

0

Filed Under (Toyota Manuals) by admin on 10-10-2011

download
passengers weighing approximately less than 100 pounds, depending on their seating position. It is important for the front seat passengers to know that proper operation of the advanced frontal airbag system is highly dependent on the pressure placed on the seat bottom. Situations that add or subtract sensed weight can result in occupant misclassification. To minimize this situation: Check seating posture. Passengers should be seated upright with their back against the seat back and feet on the floor. Check loading conditions. Extra weight from items, such as bags or groceries or toys, hanging on the seat back can add to the sensed weight of the front seat passenger. A rear seat passenger lifting the front seat with their legs, objects placed under the front seat, or the front seatback in contact with the rear seat can subtract from the sensed weight of the front seat passenger. If the passenger airbag indicator lamp continues to switch ON to OFF after checking the above conditions, perform the following repair procedure. NOTE: The safest place for children is in the rear seat. Please note that Toyota recommends that you never install a rear-facing child restraint in the front passenger seat, even if the passenger “Airbag OFF” lamp is illuminated. Please refer to you Owner’s Manual for additional details. 2004 – 2005 model year Camry, Highlander, and Solara vehicles produced BEFORE the Production Change Effective VINs shown on the following page. 2005 model year Matrix and Corolla vehicles produced BEFORE the Production Change Effective VINs shown on the following page

Incoming search terms:

2001 – 2004 Camry, Highlander, Solara & 2004

0

Filed Under (Toyota Manuals) by admin on 12-10-2011

download
2004 model year Camry, Highlander, Solara and 2004 model year RAV4 vehicles with the 2AZ-FE engine may exhibit squealing and/or rattling noises coming from the engine compartment during vehicle operation especially after a cold soak. The belt tensioner assembly has been improved to correct this condition. 2001 – 2004 model year Camry, Highlander and Solara vehicles equipped with 2AZ-FE engines produced BEFORE the Production Change Effective VINs shown below. 2004 model year RAV4 vehicles produced BEFORE the Production Change Effective VINs shown below. MODEL ENGINE LINE PRODUCTION CHANGE EFFECTIVE VIN TMMK Line 1 4T1BE3#K#4U358206 Camry TMMK Line 2 4T1BE3#K#4U914052 y 2AZFE Tsutsumi JTDBE3#K#40296732 Highlander 2AZ-FE TMK JTE#D2#A#40100501 Solara TMMK 4T1CE3#P#4U914074 RAV4 Tahara JTE#D2#V#40029797 PREVIOUS PART NUMBERCURRENT PART NUMBER PART NAME QTY 16620-28010 16620-28011 Tensioner Assembly, V-ribbed Belt 1 OP CODE DESCRIPTION TIME OFP T1 T2 EG8001 R & R Accessory Belt Tensioner 0.9 16620-28010 91 55 Applicable Warranty*: This repair is covered under the Toyota Comprehensive Warranty. This warranty is in effect for 36 months or 36,000 miles, whichever occurs first, from the vehicle’s in-service date. *Warranty application is limited to correction of a problem based upon a customer’s specific complaint

Incoming search terms:

2007 Camry And Camry SOUND DISTORTION ON AM RADIO

0

Filed Under (Toyota Manuals) by admin on 25-10-2011

download
some customers may experience a condition where certain AM radio stations have a distorted sound even though the signal from the local AM station is strong. A revised radio has been developed to address the condition. Use the following repair procedure to replace the radio. 2007 model year Camry vehicles produced BEFORE the Production Change Effective VINs shown below. 2007 model year Camry HV vehicles

Incoming search terms:

2001 – 2003 Highlander FRONT DOOR OPENING WEATHERSTRIP

0

Filed Under (Toyota Manuals) by admin on 27-10-2011

download
have been improved to better resist deformation or tearing at the bottom center portion of the front door frame. Replace the front door opening weatherstrips on vehicles with this condition built prior to the VIN breaks listed in the Production Change Information section below. 2001 – 2003 model year Highlander vehicles produced BEFORE the Production Change Effective VINs shown below. MODEL ENGINE TYPE PRODUCTION CHANGE EFFECTIVE VIN 4Cylinder 4×2 JTEGD21A#30052511 Highlander 4 Cylinder 4×4 JTEHD21A#30020710 Highlander 6Cylinder 4×2 JTEGF21A#30085273 6 Cylinder 4×4 JTEHF21A#30113260 PREVIOUS PART NUMBERCURRENT PART NUMBER PART NAME QTY 62311-48020-## Same Weatherstrip, Fr Door Opening, RH 1 62312-48020-## Same Weatherstrip, Fr Door Opening, LH 1 Replace the front door opening weatherstrip as shown in the Technical Information System (TIS). Refer to the 2001 – 2003 Highlander Repair Manual; Exterior/Interior Trim, Roof Headlining Assembly

Incoming search terms:

Incoming search terms: