v rod stage 2 instructions

You search Auto repair manual PDF v rod stage 2 instructions, if there are search results will appear below. If search results do not exist, please search by others keyword.



  v rod stage 2 instructions Direct Download speed 5282 Kb/s

  v rod stage 2 instructions Full Version speed 6162 Kb/s



Yamaha V-Star 1100 Custom and Classic cruisers Floorboard/ Footpeg Extension Installation Instructions

0

Filed Under (Yamaha) by admin on 09-11-2010

download
Start on the right (brake) side. 1) Loosen the nut at the end of the brake rod. This will allow you to unscrew the brake rod from the brake lever clevis later. 2) Pull out the cotter pin and remove the pivot pin. Unscrew the clevis 3) Then using a 14mm socket or box-end wrench, remove the two bolts that hold the brake floorboard/footpeg assembly (whichever your bike has) to the frame. These bolts are torqued to 46 ft lbs, so this may be a bit difficult. 1. Loosen this nut 2. Remove the cotter pin (other side of this pivot pin) remove the pivot pin a unscrew the nut to remove the clevis nd 3. Remove these bolts When you remove the floorboard/footpeg bracket, be careful not to pull the brake switch wires loose. You may wish to cut the cable tie for more room, and then rest the bracket, with the footpeg or floorboard attached, on a short box, or block of wood, to keep it handy. Install the new brake rod, to the end of the existing brake rod. Re-install the pivot pin, and the pivot pin cotter pin. Installing the extension bar: Note that the extension bar is bolted so that it rises up in front. Use the new bolts to mount the floorboard/ footpeg bracket to the threaded holes in front. Install the Extension in the proper orientation (angled holes bolt up to the frame, with front of the bar higher than the rear – see photo) using the stock bolts for the extensions to the frame and the new bolts and washers supplied with the kit, on the forward threaded section to relocate the floorboard or footpeg bracket. The use of LocTite ® Blue here is recommended. At this point the right side Floorboard or Footpeg should be secured tightly and the brake lever hanging loose. Now install the Brake rod extension, threading the male end to the original brake rod. Don’t tighten this end yet Place the clevis over the forward most end of the brake rod extension, and threat the clevis nut onto the end of the rod. Bring the brake rod upright, to meet with the clevis at the end of the brake rod extension and replace the pivot pin. Before reinstalling the cotter pin, check the angle of the brake lever, to insure that you have the brake pedal where you want. If necessary, adjust the extension rod in or out, until you are satisfied, and then reinstall the cotter pin into the pivot pin. Check the Brake switch wire and install a new cable tie if required. Note: Due to utilizing a thicker material, 1/2″ versus 3/8″ from our competitor, the Brake rod is now positioned at a greater angle. Even with the angle, braking performance is not affected, but if you wish to bring the master cylinder in line with the brake rod, do this. Loosen the rear, and remove the front Allen bolt. Then place two washers behind the front bolt, under the bracket, and then re-install the bolts To change the angle of the brake rod, 1) loosen and remove the two master cylinder bracket Allen bolts 2) insert two washers behind the front bolt (front of the bike), behind the master cylinder bracket 3) tighten both bolts. Do not install any washers on the rear mounting hole. This will make the angle of the Brake Rod less aggressive. Step Two – Left Side For the left (Shifter) side, 1) use an open-end 10 mm wrench, to unscrew the two nuts that hold the shift rod in place. PLEASE note that one end of the shift rod has a left hand threaded nut. SAVE the nuts, as you will need them on the new longer Polished Stainless Steel Shift Rod. 2) Remove the stock shift rod. 3) Then using a 14mm socket or box-end wrench, remove the two bolts that hold the shifter floorboard/footpeg assembly (whichever your bike has) to the frame.

Incoming search terms:

S&S Connecting Rods Installation Instructions

0

Filed Under (S&S) by admin on 29-10-2010

download
1. Female rod crankpin end to mainshaft nuts – .030″ minimum clearance recommended. A. Install sprocket shaft and crankpin in driveside flywheel. Snug nuts only. Do not torque to final specs. B. Slide connecting rods and bearings over crankpin. C. Rotate rods on crankpin, and observe clearance between rod and sprocket shaft nut. D. If additional clearance is needed, remove material from sprocket shaft nut. Do not remove material from connecting rod. E. Repeat procedure for camside flywheel and pinion shaft. 2. Female rod crankpin end to inner flywheel rim – .060″ clearance recommended. A. While checking female rod to mainshaft clearance, observe clearance between crankpin end of female rod and rim of both flywheels. B. If additional clearance is required, remove material from flywheel at point of contact. Do not remove material from connecting rod. 3. Wristpin end of both female and male rods to flywheel edge -.060″ minimum clearance recommended. A. While checking female rod to mainshaft clearance, observe clearance between wristpin end of both rods and rim of both flywheels. B. If additional clearance is required, remove material from flywheel at point of contact. Do not remove material from connecting rod. 4. Wristpin end to crankcase and cylinder – .060″ is recommended in these areas. A. With the camside flywheel and rods mocked up, install the assembly in the right crankcase half with pistons (less rings) and cylinders in place. B. Rotate flywheel through one full revolution and check for rod to crankcase and cylinder spigot contact on both the front and rear of each cylinder. C. File or grind crankcase or cylinder spigot as needed to achieve .060″ clearance. Do not remove morematerial than needed. D. Repeat for left crankcase half. NOTE: Whenever clearancing is performed in any of these areas, do not remove any material from the connecting rods as clearancing on the rods may unnecessarily weaken them. Make adjustments to the point of contact on the mainshaft nut, flywheel rim, crankcase, cylinder spigot, etc. Connecting rods weakened by clearancing may fail causing serious engine damage.

Incoming search terms:

HARLEY DAVIDSON ALUMINUM SHIFTER LINKAGE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
REMOVAL 1. See Figure 1. Remove stock shifter rod (D). 2. Adjust new shifter rod in kit to match the length of the removed shifter rod by loosening locknuts (3), adjusting the length of the rod, then tightening locknuts to 20-24 ft- lbs (27-32 Nm) . 3. For models with a straight rear shifter rod lever: Discard spacer (7). Place cover (1) over the shifter rod lever (C). For models with an offset rear shifter rod lever: Place spacer (7) and cover (1) over the shifter rod lever (C). INSTALLATION 1. Apply Loctite® 243 to threads of capscrew (5) and install cap screw through the rear of the shifter rod and into the shifter rod lever. Tighten cap screw to 13-16 ft-lbs (18-22 Nm) . 2. For 1999 and later FLHT, FLHX, FLHR, and FXDWG models: Place the rod end on the outside of the shifter lever, then apply Loctite® 243 to the threads of capscrew (5). Attach the front of the shifter rod (6) to the shifter lever with capscrew (5) and acorn nut (4) (with acorn nut facing out). Tighten acorn nut (4) to 13-16 ft-lbs (18-22 Nm) . For all models except 1999 and later FLHT, FLHX, FLHR, and FXDWG: Place the rod end on the inside of the shifter lever then apply Loctite® 243 to the threads of cap screw (5). Attach the front of the shifter rod (6) to the shifter lever with cap screw and acorn nut (4). Tighten acorn nut (4) to 13-16 ft-lbs (18-22 Nm)

Incoming search terms:

SUSPENSION SERVICE TOOLS/ FORK DAMPER ROD BLEED TOOL

0

Filed Under (Tips and Review) by admin on 30-11-2010

download
33 SHOP EQUIPMENT & TOOLS SUSPENSION SERVICE TOOLS K&L FORK TUBE U-BLOCKS Precision machined from billet aluminum, these quality three piece sets are a handy, accurate and safe way to straighten and check fork tubes. 35-9411 36mm (for 33 thru 36mm tubes) 35-9412 40mm (for 37 thru 40mm tubes) 35-9413 43mm (for 41 thru 43mm tubes) 35-9414 46mm (for 44 thru 46mm tubes) 35-1964 35-8579 35-7995 DAMPER ROD HOLDERS Holds damper rod when disassembling forks. 35-8578 Yamaha front forks, 43mm Kayaba YZ125/250 (1988) YZ490 (88-90) 35-8579 Yamaha YZ125/250 with UD(upside down) forks FORK DAMPER ROD TOOLS Sold each. 35-7995 Combination Fork Damper Tool Designed to hold the damper rod during assembly & disassembly of Honda XR400′s or Suzuki DR-Z400S. One end features spanner type prongs for the XR400 and the other a 27mm hex for Suzuki. 35-1964 Combination Damper Rod Fork Tool Designed for assembly and disassembly of most inverted Kayaba and Showa 41mm, 43mm, 46, and 47mm forks. Use one end for Kayaba forks and the other for Showa forks. (not required for 91-92 Honda CR models) ROD HOLDER Double sided damper rod holder. Works on Kayaba U.D (upside down) 41mm forks. 35-8580 Yamaha YZ125/250Amodels (89-90) FRONT FORK CAP SOCKET Designed to remove and install Yamaha front fork caps with female hex head. Sold each. 35-8571 14mm female socket 35-8573 19mm female socket FORK DAMPER ROD HOLDERS Holds damper rod when disassembling and assembling front forks. 35-8576 Use for Yamaha 43mm Kayaba forks, 30mm hex YZ125 (84-87), YZ250 (81-87) IT250 (1983) YZ490 (82-87) 35-8577 Use for Yamaha 38mm Kayaba forks, 24mm hex YZ125 (81-83), IT175 (82-83), IT250 (81-82) YZ250 (77-80), YZ400 (77-79), IT465 (81-82) FORK CAP WRENCH Designed to remove the front fork caps on late model Honda CR’s and Suzuki RM’s. Can also be used for adjusting compression. One end of wrench is 49mm, the other is 50mm. Sold each. 35-7803 Fork Cap Wrench 35-8576 35-8577 35-8571 35-8573 6 Point Hex 35-8578

Incoming search terms:

Kawasaki KLR Lowering Kit Installation Instructions

0

Filed Under (Kawasaki) by admin on 01-12-2010

download
locate the OEM tie rods (circled in yellow, in the picture below), and the rear shock absorber snubber (circled in red, in the picture below). Notice that there is a tie rod on each side of the motorcycle. These tie rods are secured by two long bolts that pass first through the LH tie rod, then through the suspension, and finally held in place by two 17mm nuts on the RH side. Loosen these two 17mm bolts, and prepare them for removal. It helps to raise the rear tire just slightly with a jack or by a helper, to take the load off of these 17mm bolts. Below is another picture, better exposing the orange rubber snubber on the lower shock absorber rod… This is where the snubber spacers are installed, but don’t do it just yet…there’s more info on this later in the instructions. 3. Remove the 17mm nuts from the tie rods, keep the weight off of the rear wheel, and remove the upper and lower bolts from the tie rods. The rods are easily removed at this point. Take notice that the LH rod has recesses in each end, where the heads of the 17mm securing bolts fit. 4. Replace the tie rods with the new Scootworks tie rods in your kit. Install the tie rod with the recessed bolt holes on the LH side, with the recesses facing outward. Re-install the bolts from the LH side, through the LH tie rod, through the suspension, and through the RH tie rod. Secure them with the original nuts, and torque to 43 ft/lbs. The recessed bolt holes in the LH tie rod are seen in the picture of the Scootworks KLR tie rods below… 5. Do not install the plastic snubber spacers at this time. Lower the rear of the bike and remove the frame from the lift or jack stands. The rear lowering is completed. Sit on the motorcycle and determine if you’ve lowered it to a satisfactory level. If not, proceed to step #6. Your Scootworks KLR Lowering Kit is now installed. The following information is supplied as a supplement, to allow you to complete the job of lowering your bike that you’ve begun by using this Quality Scootworks product. NOTE: Be sure to check the chain tension after installation of the lowering kit, and adjust as necessary. Tips for setup and use of your lowering kit BE SURE to read the FAQ at the end of this document, for tips, warnings, and adjustments for your new lowering kit! Lowering the Front of your KLR-series Motorcycle

Incoming search terms:

HARLEY DAVIDSON EFI SCREAMIN' EAGLE BIG BORE EFI STAGE 2 KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
INSTALLATION Installation of this kit is divided into six steps: 1. Big-Bore Cylinder and Piston Conversion 2. High Performance Camshafts 3. High Performance Clutch Diaphragm Spring 4. High Performance Air Cleaner 5. Calibrate the ECM 6. Exhaust NOTES This Big-Bore Stage 2 kit is intended for High Performance applications only. This engine-related performance part is legal for sale or use in California on pollution-controlled motor vehicles. Engine-related performance parts are intended for the experienced rider only. -J04173 1 of 5 The air cleaner contained in these kits is designed to perform with these kits only. Any other combination of components is not confirmed to be legal for street use. The Product Information Label contained in this kit is required in the state of California only. This label is required to aid in passing the California Smog Check Program. Place the Product Information Label on the right side of the frame, directly beneath the VIN sticker. Do not place the label on motorcycles other than those specified in the Instruction Sheet. Gaskets provided in the 1690 conversion kit eliminate the need for original head gasket O-rings. For this reason, DO NOT install the Original Equipment (OE) O-rings (Part Number 11273) to the top of cylinder dowels, or severe engine damage may occur. Big-Bore Cylinder and Piston Conversion NOTE Installation of this kit requires removal of the cylinder heads, cylinders and pistons. Refer to Section 3, ENGINE: STRIPPING MOTORCYCLE FOR SERVICE and TOP END OVERHAUL of the applicable Service Manual for instructions. High Performance Camshafts NOTE Installation of this kit requires removal and re-installation of the cam support plate. Refer to Section 3, ENGINE: BOTTOM END Cam Support Plate, Removal and Disassembly/Assembly (Camshaft, Camshaft Bearings) of the applicable Service Manual for instructions. Measuring Piston-to-Valve Clearance After installing non-stock cams, check piston-to-valve clear- ance. 1. Apply 1/8-inch (3 mm) layer of clay to crowns of pistons in areas where valves meet pistons. 2. Refer to the appropriate Service Manual and assemble the heads and valve train, and tighten cylinder studs to torque specified. 3. Turn engine through two complete revolutions by hand. 4. Remove heads and measure clay at its thinnest point. NOTE Clay must measure 0.080 inch (2.03 mm) at its thinnest point. If this measurement does not meet minimum thickness, depth of valve notches must be increased. The depth of the notches must not exceed 0.135 inch (3.43 mm). Measuring Valve-to-Valve Clearance NOTE Wait ten minutes before turning the engine after installing push rods. This allows tappets to bleed down and prevents you from bending push rods or valves. 1. Rotate the engine so that both valves of the front cylinder are partially open. Shine a light through the exhaust port and look through the spark plug hole to view the valves. Turn engine, if required, to the point where the exhaust evel sensor to the fuel pump with screw (3). Tighten the screw enough to seat the fuel sensor against the mounting tab e. Route fuel level sensor wiring under the fuel hose and connect the fuel level sensor to the low fuel switch connector on the fuel pump module. If necessary use the jumper harness (Figure 4, item 5). f. See Figure 2. Secure the fuel pump wires and con- nectors

Incoming search terms:

HARLEY-DAVIDSON V-ROD BIG BORE KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
The cylinder sleeves provided with the Wiseco V-Rod big bore kit have been finished honed to size and the piston to cylinder clearance has been set. Prior to installation, the sleeves must be washed in hot soapy water (not parts washer solvent) and dried. Coat the bore surface with motor oil and wipe it with a white towel. If the towel shows any remaining grit, repeat the hot soapy water washing process until the towel will only show clean motor oil. CAUTION: Test fit the cleaned sleeve (without O-Rings installed) into the engine block. Sleeve should drop into position. If sleeve will not easily drop into position, warm the engine block with a hair dryer until sleeve will drop into position. Remove sleeve, then continue installation procedures. From the bottom side of the sleeve, gently roll the 2-cylinder sleeve O-rings into the two grooves on each sleeve. Apply motor oil to the O-rings and gently install the sleeves into the block until bottomed. CAUTION: DO NOT ATTEMPT TO INSTALL SLEEVES WITHOUT LUBRICATING THE O-RINGS. FAILURE TO LUBRICATE O-RINGS COULD RESULT IN TORN OR DAMAGED O-RINGS THAT WOULD NOT BE EVIDENT UNTIL ENGINE WAS STARTED. INCORRECTLY INSTALLED O-RINGS CAN RESULT IN CATASTROPHIC ENGINE DAMAGE. NOTE: REFER TO THE OEM SERVICE MANUAL FOR ALL TORQUE SPECIFICATIONS PISTON RING PREPARATION Wiseco V-Rod pistons incorporate an advanced 2 ring system • The top ring is file-fit, and as such, requires that the end gap must be clearanced. The proper end gap clearance is .016-.018″ with the ring installed squarely in the bore. The top ring must be installed on the piston with the dot marking toward the top of the piston. • The oil ring is comprised of the expander and two rails. Install the expander first, and then the rails. Check to make sure the expander tips have not overlapped. It is not necessary to clearance the end gaps on the oil rails. The rails should be installed without modification. PISTON INSTALLATION The Wiseco V-Rod big bore kit is supplied with pistons that are front and rear cylinder specific. Install the front piston 4792M10795 in the front cylinder with the arrow facing the front of the engine. Install the rear piston 4793M10795 in the rear cylinder with the arrow facing the front of the engine. A piston ring compressor is required to install the pistons into the cylinders. Front of engine ➔ 4792M10795 ( Front piston) 4793M10795 ( Rear piston) FWD 4793M10795 FWD 4792M10795 For further information call the Wiseco Tech Line:

Incoming search terms:

HARLEY DAVIDSON SECURITY SYSTEM SMART SIREN KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
REMOVAL 1. Refer to the owner’s manual and follow the instructions to disarm the security system. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) To prevent accidental vehicle start-up, which could cause death or serious injury, remove main fuse before proceeding. (00251b) 2. For All Models except 2002-2003 Touring and 2003- Later Softail: Refer to the owner’s manual and follow the instructions to disconnect the battery, negative (-) cable first or remove the main fuse. For 2002-2003 Touring and 2003-Later Softail Models: Remove seat following the instructions in the service manual and disconnect the battery, negative (-) cable first. Save seat hardware for installation. INSTALLATION 2002-2006 VRSCA, VRSCB, VRSCD Models 1. Open the seat. 2. See Figure 1. Remove the splash guard (mud flap) nuts. 3. See Figure 2. Lower the mud flap from the installed position and allow it to rest on the rear tire 3. Slide the siren into place on the left side of the electrical caddy so the sounder disc (6) faces out. 4. Refer to the owner’s manual and follow the instructions to install the main fuse. 5. Align the barbed studs on the side cover with the grommets in the frame and push side cover firmly into place. 6. Install the left side saddlebag per the instructions in the owner’s manual. 2003 and later Softail Models EXCEPT FXCW/C 1. Remove the right side saddlebag (if equipped) per the instructions in the owner’s manual. NOTE The siren connector is installed on an electrical panel under the rear fender on all Softail models. The rear of the motorcycle may have to be raised slightly to allow removal of the splash guard. 2. Remove the two bolts at the bottom of the splash guard. Bend the upper right corner of the splash guard toward the rear tire and lift upward to unhook the splash guard from the tab on the rear fork. Remove the guard from beneath the fender. 2 1 3 is01316 1. Siren mounting area 2. Siren connector [142B] 3. Harness clip Figure 16. Siren Connector (Softail Models EXCEPT FXCW/C) (Rear Fender View with Rear Wheel Removed) 3. See Figure 16. Remove the siren connector [142B] (2) from the receptacle in the siren mounting area (1) of the electrical panel. 4. See Figure 17. Insert security siren (1) connector [142B] into the siren box receptacle until the connector latches securely. 5. Orient the siren (1) as shown, with the harness connector (2) toward the bottom and the sounder disc (5) facing out. Carefully snap the siren into the electrical panel. 6. Insert the siren harness lead (4) into the harness clip (3) to keep the harness clear of other components. 7. If necessary, secure the connector wiring to the electrical panel wiring with a cable strap (not provided). 8. Hook the slot at the top of the splash guard over the tab on the rear fork and install the guard with the two screws removed earlier. Tighten securely. 9. Install the right side saddlebag (if equipped) per the instructions in the owner’s manual. 10. Refer to the owner’s manual and follow the instructions given to connect the battery cables or install the main fuse

Incoming search terms:

HARLEY DAVIDSON SPORTSTER ALUMINUM SHIFT LINKAGE KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 10-03-2011

download
INSTALLATION 1. See Figure 1. Remove stock capscrews (4) and stock shifter rod (2). Discard stock capscrews. 2. See Figure 2 and Table 2. Loosen the lock nuts (5) and turn the rod ends on the new aluminum shifter rod (1) to match the length of the stock shifter rod. 3. See Figure 2 and Table 2. Slide longer capscrew (3) through the front rod end of new shifter rod (1). Place rod on the outside of the lever assembly. Thread capscrew (3) into the lever assembly. 4. Slide shorter capscrew (2) through the rear rod end of new shifter rod (1). Place rod on the outside of the transmission shift lever. Thread capscrew (2) into the transmission shift lever. 5. Tighten capscrews to 10-15 ft-lbs (13.6-20.3 N-m) . 6. Firmly tighten the lock nuts (5) against the rod ends to 20- 24 ft-lbs (27.1-32.5 Nm) . 1 4 2 4 3 is05394 1. Lever assembly 2. Shifter rod 3. Transmission shift lever 4. Capscrew Figure 1. Shift Linkage Components

Harley-Davidson Motorcycle Reverse Gear Installation Instructions

0

Filed Under (Harley Davidson) by admin on 31-10-2010

download
2.1 Obtain a small tube of Loctite® #262 (red) for use later. 2.2 Drain the transmission oil. 2.3 Remove the clutch adjustment cover (left side). 2.4 Remove rear exhaust header pipe (cross over exhaust pipe). 2.5 Remove the muffler support bracket. 2.6 Remove the clutch release cover (right side). 2.7 Remove clutch push rod and oil slinger. To be disassembled and modified later. 2.8 Remove the two nuts from the main (rear) and counter (front) transmission shafts. 2.9 Remove the transmission bearing housing (puller available from Champion Sidecars). To be replaced with new reverse gear transmission bearing housing (Trap Door). 2.10 Cover the exposed gears in the transmission with a cloth in preparation to cut the shifter fork shaft. 3 Install New Main and Countershaft Gears NOTE: Gears and Tapered Split Rings are factory matched sets. Do not mix!. 3.1 Locate the shifter fork rod, mark fork rod flush at transmission case and pull out 1/4″. Figure 1 Figure 2. Exposed Shoulders Mark shifter fork rod flush with case Remove Spacers Vehicle Transmission Counter Shaft Main Shaft Front of Motorcycle Figure 1
Reverse Gear Installation Instructions For EVO / 5 Speed and Twin Cam Harley-Davidson® Motorcycle Page 3 of 6 Revision 7 © 2007 Champion Motorcycle Accessories International, Inc. dba Champion Sidecars 11841 Monarch Street Garden Grove, CA 92841 (800) 875-0949 (714) 847-0949 www.championsidecars.com www.championtrikes.com Figure 6 CAUTION: Do not pull the shifter fork rod out of the transmission more than 1/4″. If you pull the shifter fork rod out too far, it will be difficult to realign it with the internal shifter fork. 3.2 Cut the shaft at the mark and push it back in. The shaft end MUST NOT stick out of the transmission case. If the shaft is in deeper, fill the hole with silicone to prevent the shaft from moving in and out. NOTE: Shifter fork is made of non-tempered metal and may be cut with a hacksaw or Dremel® cutting tool. 3.3 Important: Remove stock spacers from main and counter shafts. Spray with silicon remover (Brake-Clean) then, using supplied cleaning pad, clean shafts, new counter and main shaft gears and tapered lock rings (inside and outside) Figure 1 3.4 With motorcycle in neutral, pull both the shafts out and simultaneously push the OEM outermost gears in until seated completely to expose the shoulders of both shafts. The countershaft shoulder should be flush with the gear face. For the main shaft the gear would “hang over” the shoulder a small bit. Figure 2 3.5 Apply supplied Champion Super-Lock retaining compound to the inside and outside surfaces of the large gear tapered split ring, to the inside of the new countershaft gear (large gear) and to the transmission countershaft (the forward most shaft). 3.6 Install new countershaft gear to the transmission countershaft. Insert tapered split ring (tapered end first) into the countershaft gear. Install ring seat tool and spring to counter shaft and new countershaft gear. Torque ring seat tool to 40 ft-lb’s. Figures 3 and 4

Incoming search terms:

Incoming search terms: