v star 650 classic shifter

You search Auto repair manual PDF v star 650 classic shifter, if there are search results will appear below. If search results do not exist, please search by others keyword.



  v star 650 classic shifter Direct Download speed 5282 Kb/s

  v star 650 classic shifter Full Version speed 6162 Kb/s



TRIUMPH ROCKET III HEEL / TOE SHIFTER INSTALLATION INSTRUCTIONS

0

Filed Under (Triumph) by admin on 29-01-2011

download
1. Loosen the 10mm nuts at the ends of the shifter linkage rod (notice one end is a left hand thread). Remove the 10mm nut from the shifter arm & disengage the linkage. Remove the shifter pivot bolt using a 8mm hex key wrench. Remove the washer on the threaded side of the shifter pivot bolt. 2. Place one of the wave washers supplied onto the pivot bolt. Place a small amount of grease on the shifter pivot bolt shank and the Heel / Toe shifter pivot hole, insert the pivot bolt into the pivot hole of the toe heel shifter. Use a drop of blue loctite on the shifter pivot bolt threads and install the Heel / Toe shifter, tighten the pivot bolt securely. Check to see that the shifter pivots freely. If the side play is excessive (this is a result of variances in manufacturing tolerances of the stock and supplied components) remove the pivot bolt and install the second wave washer supplied. 3. Unscrew the linkage rod and replace it with the longer rod supplied (NOTE the rod has a left hand thread on one end and right hand threads on the other). Insert the shifter linkage stud into the desired hole in the new shifter being sure the flats on the stud engage the slot on the backside of the bolthole. Install the nut and finger-tighten only at this time. 4. While seated on the motorcycle first find the height setting you prefer for the toe shifter. Using one of the three boltholes for the linkage can set this. You can also gain some adjustment by exposing more or less threads of the new longer shifter linkage rod; however be sue that you have a minimum of 4-5 threads still engaged in the linkage ends. After setting the height, tighten all three 10mm nuts (the two at the ends of the linkage rod and the one which attaches the linkage to the toe/heel shifter) securely. After you have the toe shifter adjusted to your liking you can select the heel shifter height by moving the button head cap screw that secures the toe shifter to the heel shifter (Using a 5/32″ hex key wrench) next to the 10mm linkage nut to any of its three holes

Incoming search terms:

HARLEY DAVIDSON ALUMINUM SHIFTER LINKAGE REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 15-02-2011

download
REMOVAL 1. See Figure 1. Remove stock shifter rod (D). 2. Adjust new shifter rod in kit to match the length of the removed shifter rod by loosening locknuts (3), adjusting the length of the rod, then tightening locknuts to 20-24 ft- lbs (27-32 Nm) . 3. For models with a straight rear shifter rod lever: Discard spacer (7). Place cover (1) over the shifter rod lever (C). For models with an offset rear shifter rod lever: Place spacer (7) and cover (1) over the shifter rod lever (C). INSTALLATION 1. Apply Loctite® 243 to threads of capscrew (5) and install cap screw through the rear of the shifter rod and into the shifter rod lever. Tighten cap screw to 13-16 ft-lbs (18-22 Nm) . 2. For 1999 and later FLHT, FLHX, FLHR, and FXDWG models: Place the rod end on the outside of the shifter lever, then apply Loctite® 243 to the threads of capscrew (5). Attach the front of the shifter rod (6) to the shifter lever with capscrew (5) and acorn nut (4) (with acorn nut facing out). Tighten acorn nut (4) to 13-16 ft-lbs (18-22 Nm) . For all models except 1999 and later FLHT, FLHX, FLHR, and FXDWG: Place the rod end on the inside of the shifter lever then apply Loctite® 243 to the threads of cap screw (5). Attach the front of the shifter rod (6) to the shifter lever with cap screw and acorn nut (4). Tighten acorn nut (4) to 13-16 ft-lbs (18-22 Nm)

Incoming search terms:

HARLEY DAVIDSON SHIFTER SHAFT COVER WITH INSERT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION 1 2 4 3 5 6 7 is01872 1. Shifter shaft 2. Inner cover 3. Toe shifter lever 4. Outer cover 5. Set screw (for outer cover) 6. Set screw (for inner cover) 7. Casting Figure 1. Shifter Shaft Covers 1. See Figure 1. Remove the stock heel shift lever and toe shift lever (3) from the gear shifter shaft (1). 2. Install the set screw (6) into the inner gear shifter shaft cover (2). 3. Install inner gear shifter shaft cover with installed set screw over the casting (7) in-board of the shifter shaft (1). 4. Tighten the set screw until light contact is made with the casting. Do not overtighten. 5. Re-install toe shift lever on the gear shifter shaft. Tighten the shifter retaining screw to 18-22 lb-ft (24-30 Nm) . 6. Install the set screw (5) into the outer gear shifter cover (4). 7. Install outer gear shifter shaft cover with installed set screw over the end of the gear shifter shaft (1). 8. Loosen the set screw slightly to allow the gear shifter shaft cover to rotate. Rotate the cover until the set screw faces down, then tighten the set screw. SERVICE PARTS

Incoming search terms:

HARLEY DAVIDSON DYNA FLOORBOARD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 23-03-2011

download
Installation SHIFTER ASSEMBLY (LEFT SIDE) 1. Remove highway footrest assembly, if equipped. Discard bracket, plate and mounting hardware. 2. Remove stock footrest assembly. 3. Remove stock (chrome) shift lever. Retain shift lever, peg, bolt and washer. 1 WARNING ® 1 of 5 Kit Number 50601-01 -J01921 2 of 5 Figure 1. Shifter Assembly (Left Side) Item Description Part No. 1 Bolt, 5/16-18 x 5/8 hex HD 2882W 2 Hex cap screw, 5/16-18 x 2.00 (2) 3023 4 Set screw, shaft cover 3231B 6 Assembly,shift lever 33704-01A 7 Assembly,adjustable shifter rod 33719-79B 8 Lever, shifter, machining, polish 33706-01 9 Assembly, shifter plate, polish 33700-01 10 Cover, shifter lever, rubber (2) 34619-85 11 Retainer,shift lever for 1996 to 2000 models 34639-93 Item Description Part No. 11ARetainer bracket, shift lever for 2001 and later models 34639-01 12 Cover, shifter shaft 34640-93 13 Washer, wave, overlap type (2) 34641-01 17 Socket head cap screw 4740A 25 Washer, 5/16″ (2) 6016 28 Washer. 5/16″ 6702 30 Nut, hex, locking, 5/16-18 7710W 32 Acorn nut, 5/16-24 7736 33 Hex jam nut, 5/16-24 7744 30 11 1 12 7 32 28 6 13 9 25 2 17 25 2 10 8 i03110.eps 33 4 11A ’96-2000 models 2001 and later models 4. See Figure 1. 1996 to 2000 models. Bolt shifter lever shaft retainer bracket (11) to the stock shifter lever with bolt (1) and nut (30). Do not tighten bolt at this time. 2001 and later models. Bolt shifter lever shaft retainer bracket (11A) to the stock shifter lever with bolt (1) and nut (30). Do not tighten bolt at this time. 5. Loosen the left rear crankcase bolt (at bottom of cylinder) and slide the slotted end of shifter lever shaft retainer bracket (11) onto the bolt, but beneath the washer. Tighten crankcase stud to 15-17 ft-lbs (20-23 Nm). 6. Place chrome cover (12) on shifter lever shaft (at primary case) and secure with set screw (5). NOTE Small wave washer (13) goes between foot shifter and bracket. 7. See Figure 1. Place small wave washer (13) on shifter lever (6) shaft. Coat shaft with Loctite Anti-seize and slide into bracket. 8. Install foot shift bracket (9) using screws (2). Tighten screws to 25-30 ft-lbs (34-41 Nm). 9. Place shifter rod (2) and washers (25) in position. Use short stud on shifter rod to secure shifter rod at the transmission end. Use Loctite 242 (blue) on stud before installing. 10. Install acorn nut (32) and washer (28) at foot shift end. Use Loctite 242 (blue) on acorn nut before installing

Incoming search terms:

Single-Cylinder BMW G 650 X Model Series

0

Filed Under (BMW) by admin on 16-11-2010

download
introducing the new range of single-cylinder models, BMW Motorrad is broadening its model line-up with a clear focus on additional target groups. Proceeding from the same technical foundation, the Company has created three new motorcycles absolutely different in their features and characteristics: the G 650 Xchallenge Hard Enduro, G 650 Xmoto Street Moto, and the G 650 Xcountry Scrambler. With their outstanding product substance, their purist looks, and their exceptionally sporting riding characteristics, these single-cylinder models are filling attractive niches in the market. And through their low unladen weight of less than 160 kg or 353 lb according to the DIN standard, they offer dynamic performance for both the connoisseur and the sports-minded rider. Market launch of the new G 650 X model series is planned in good time for the beginning of the season in spring 2007. These new machines with the smallest engines in the BMW model range offer particularly the young and young-at-heart motorcycle rider exactly the right entry into the world of BMW motorcycles, but are not entry-level bikes in the conventional sense of the word: On the contrary, the G 650 Xchallenge Hard Enduro will thrill the customer who wishes to really benefit from the enormous offroad potential of his machine. The G 650 Xmoto Street Moto, in turn, with its very impressive active riding qualities, offers the genuine enthusiast a new dimension in riding pleasure. The G 650 Xcountry Scrambler, finally, stands for carefree riding pleasure and nimble performance both on the road and off the beaten track. Indeed, this unique machine is able to meet all kinds of requirements and offer virtually all riding qualities ranging from city use via country roads and small, winding lanes, all the way to offroad tracks presenting the most challenging requirements. The G 650 Xcountry therefore conveys the classic but relaxed feeling of riding a genuine Scrambler as well as the concept of “wandering” on your motorcycle into today’s world in a most modern style. And last but certainly not least, riding pleasure is guaranteed under all conditions and in every situation, since the G 650 Xcountry offers the same outstanding engine and running gear qualities as its two very sporting “sister models

Incoming search terms:

YAMAHA V-STAR 650/ 1100 CLASSIC F ATS/ SLIMS MOUNTING KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 10-11-2010

download
1. Cover gas tank and front fender with towels to avoid damage during installation. 2. Install the two mounting plates onto the windshield, using the bottom and third bolt up. Leave the nylon washers off. The small tab goes to the bottom, big one at the top. (see Figure 1) Tabs face out away from the headlight when installed correctly. 3. Remove the headlight lens and chrome Turn Signal Bar cover and set them in a safe place. (see figure 2) 4. Remove the (3) socket head cap screws that hold the Headlight housing and let it rest carefully so that it does not fall. 5. Remove the turn signal bar by extracting the two socket head cap screws and let it dangle. (see figure 2) 6. Loosely install the throttle-side Bracket and Headlight using one of the (3) new longer 6mm x 30mm socket head cap screws. The nylon washer goes in between Headlight Housing and Headlight Bracket. (see figure 3) Install one of the (2) new 8mm x 45mm SS flat head screw and spacer in the lower hole to mount the turn signal bar. Insert the bolt in this order: bolt – windshield bracket – spacer – turn signal bar, and loosely tighten . (see Figure 3) Repeat these steps for the Clutch side. (See figure 4 for optional Cobra Light Bar installation, or to move Turn Signals forward to mount Lowers closer to the windshield.) 7. Once both windshield brackets are in place and all the new bolts are in place, Tighten all bolts. Re-install the chrome Turn Signal Bar cover. (Leave the chrome cover off if you use the alternate installation for Light Bar or Lowers). Re-Install the Headlight lens. 8. Loosen the (4) anchor bolts on the side of the windshield brackets. Slip the windshield mounting plates onto the brackets starting with the upper slot first then slip the bottom slot in. Adjust height, angle and tighten all bolts. This is a quick change kit. ALWAYS tighten all mounting bolts after removing or installing the windshield

Incoming search terms:

harley- davidson DYNA BLACK FORWARD CONTROL KIT installation Manual

0

Filed Under (Harley Davidson) by admin on 15-03-2012

download
1. Disconnect battery cable, negative (-) cable first. 2. Remove the left side rider footrest assembly. Save the footrest and fasteners for installation. Discard the remaining hardware. 3. From the kit, press hole plugs (8) into the screw holes on the frame where the stock footrest assembly was mounted. 4. Remove plugs from forward control frame mount (I) and discard. 5. Remove the foot shifter lever (A) and shifter peg (D). Discard the old foot shifter lever (A). Save the foot shifter lever hardware and shifter peg (D) for future use. 6. See Figure 2. Remove the primary chaincase cover (6) and primary chaincase housing (1). Refer to your model motorcycles Service Manual for removal procedures. NOTE See Figure 1. Before removing the gear shifter lever (1) ((H) in Table 1), it is necessary to mark the correct orientation of the lever. Using a marking tool, draw a location marking (4) on the end of the splined shaft (2) across from the casting split (3). This will allow the new gear shifter lever to be installed in the same orientation as the old lever. 5 3 4 1 2 is 02083 1. Gear shifter lever 2. Splined shaft 3. Casting split 4. Location marking 5. Lever bolt Figure 1. Gear Shifter Lever Orientation 7. After marking the gear shifter lever orientation, loosen the lever bolt (5) and remove the old shifter lever. Discard the old gear shifter lever but keep the lever bolt. From the kit, install the new gear shifter lever onto the splined shaft in the same orientation as the old shifter lever. Tighten the lever bolt to 18-22 ft-lbs (24.4-29.8 Nm)

ODYSSEY DRYCELL MOTORCYCLE BATTERY COMPATIBILITY

0

Filed Under (Triumph) by admin on 30-10-2010

download
BMW 1200 1200 1150 1100 1100 1000 1000 1000 1000 900 850 800 800 800 750 750 750 750 750 650 650 600 600 500 BUELL 1200 1200 1200 1000 DUCATI 860 750 500 HARLEY DAVIDSON 1570 1570 1450 1450 1340 1340 1340 1200 883 HONDA 1800 1500 1200 1100 1000 1000 900 750 750 650 650 650 600 400 200 150 150 125 K1200RS, LT R1200C R1150GS, R R1100GS/R R1100RS/T/S/LT “K” Models R100/7 100RS R100GS, R, RS, RT R90/6, R90S R850R R80GS, R80ST R80, R80RT R80/7/RT K75, RT K75C, S R75/5 R75/7 R75/6 R65 R65LS R60/5 R60/6, R60/7 R50/5 S1 Lightning X1, S3, S3T, M2 S2/T, RS1200, RR1200 RR1000 GT, GTS GT, Laguna Seca GTL, GTV, Sport FXST, FLST FXD FXD FXST, FLST FXD FXST, FLST FL/H/T/HT XL, XLH XLH, XLH GL1800, VTX1800C Gold Wing-All Gold Wing-All Gold Wing-GL1100 CBX1000, SS opt. Gold Wing-GL1000 CBR900R,RR CB750A (Hondamatic) VFR740R/ RVF750R NT650, SLR650, NX650 Vigor 650 XR650L VT600C, CD, CBR600 CBR400F CB-1 TR200 Fat Cat CH150 Elite FES150 FES125, Pantheon (97 -) (98 -) (00 -) (94-00) (90 -) (83-93) (76-84) (83) (87-95) (69-76) (95-97) (80-96) (84-95) (78-84) (85-95) (85-95) (70-73) (76-84) (69-76) (84-95) (78-84) (70-73) (69-84) (70-73) (96-99) (ALL) (ALL) (87) (2007) (2007) (99-06) (00-06) (97-99) (91-99) (80-96) (97-03) (97-02) (01-06) (88-00) (84-87) (80-83) (82) (75-79) (93-99) (76-78) (90/94) (88-91) (ALL) (93-06) (87-03) (89-90) (86) (87) (ALL) (ALL) #3561 #3561 #3561 #3561 #3561 #4989 #4989 #3561 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #3591** #3591 #3591 #3591 #4989 #4989 #3561 #3591 #2528 #2528 #3591 #2528 #3591 #3560 #2528** #2528** #2528 #3560* #3560* #3560* #3560* #3560* #2519* #3560* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* PC680 PC680 PC680 PC680 PC680 PC925L PC925L PC680 PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC545MJ PC545MJ PC545MJ PC545MJ PC925L PC925L PC680 PC545MJ PC545 PC545 PC545MJ PC545 PC545MJ PC680MJ PC545 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 cc model (year) cat. # mfg sku # KAWASAKI 1500 1500 1300 1000 1000 900 900 750 750 650 636 600 600 KTM 640 620 400 400 MOTO GUZZ I 1100 1100 1100 1000 1000 850 850 750 650 650 650 500 POLARIS All SUZUKI 1400 900 750 750 750 650 600 600 600 600 400 TRIUMPH 600 YAMAHA 1600 1300 1300 1200 1100 1100 1100 920 600 600 VN 1500-A Vulcan VN 1500-C Vulcan KZ 1300 Touring KZ 1000-P Police Z1000 ZX900-C, Ninja ZX900-E, F Ninja KZ750-L, Ninja Zx750 Ninja ZX, 7RR KLX650C, R ZX636-B Ninja ZX-6R ZX600-G, J Ninja ZX ZX600-K Ninja ZX Adventure, Duke, RXC Adventure, Duke, LC4 LC4 E/XC RXC LC4 Cali/Spc/Jackl/Stone/EV Quota/Sport 1100 VII EV/Bassa California III,Quota,Millie Convert,Daytona, LeMans LeMans T3, T4, T5 Nevada,NTX,Strada,V7,V75 NTX V65 V65 Florida V50 Victory GV 1400GC RF900, R, S, ZS GSX750F Katana GSX-R750 GSXR750W DR650SE GSF600S Bandit GSX600F Katana GSX-R600 RF600R, S GSF400 Bandit Daytona 600 XV 1600 Road Star 1300 Royal Star XVZ Venture Royale XVZ12T Venture XJ1100 Maxim XS 1100, L, S XV 1100, S/ Virago XV 920/R/M Virago XJ600S Seca II XT600E (87-98) (96-97) (79-82) (82-05) (03-04) (98-99) (00-04) (93) (91-97) (93-96) (03-04) (98-02) (03) (99-02) (96-98) (96-98) (96-01) (94-05) (97-02) (98-99) (ALL) (86-88) (94-97) (98-03) (96-99) (94-95) (96-04) (96-03) (98-04) (97-03) (94-96) (91-93) (03-04) (99-03) (96-03) (86-92) (83-85) (82) (78-92) (86-99) (81-83) (92-98) (90-95) #3560 #3560 #3560 #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #4989 #2528 #4989 #4989 #4989 #4989 #4989 #3561 #3561 #4989 #3561 #4989 #2519* #3560 #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2519* #2528*** #2528*** #3560 #3560 #3560 #3560 #3560 #3560 #2519* #2519* PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC925L PC545 PC925L PC925L PC925L PC925L PC925L PC680 PC680 PC925L PC680 PC925L PC310 PC680MJ PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC310 PC545 PC545 PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC680MJ PC310 PC310

Incoming search terms:

Yamaha V-Star 1100 Custom and Classic cruisers Floorboard/ Footpeg Extension Installation Instructions

0

Filed Under (Yamaha) by admin on 09-11-2010

download
Start on the right (brake) side. 1) Loosen the nut at the end of the brake rod. This will allow you to unscrew the brake rod from the brake lever clevis later. 2) Pull out the cotter pin and remove the pivot pin. Unscrew the clevis 3) Then using a 14mm socket or box-end wrench, remove the two bolts that hold the brake floorboard/footpeg assembly (whichever your bike has) to the frame. These bolts are torqued to 46 ft lbs, so this may be a bit difficult. 1. Loosen this nut 2. Remove the cotter pin (other side of this pivot pin) remove the pivot pin a unscrew the nut to remove the clevis nd 3. Remove these bolts When you remove the floorboard/footpeg bracket, be careful not to pull the brake switch wires loose. You may wish to cut the cable tie for more room, and then rest the bracket, with the footpeg or floorboard attached, on a short box, or block of wood, to keep it handy. Install the new brake rod, to the end of the existing brake rod. Re-install the pivot pin, and the pivot pin cotter pin. Installing the extension bar: Note that the extension bar is bolted so that it rises up in front. Use the new bolts to mount the floorboard/ footpeg bracket to the threaded holes in front. Install the Extension in the proper orientation (angled holes bolt up to the frame, with front of the bar higher than the rear – see photo) using the stock bolts for the extensions to the frame and the new bolts and washers supplied with the kit, on the forward threaded section to relocate the floorboard or footpeg bracket. The use of LocTite ® Blue here is recommended. At this point the right side Floorboard or Footpeg should be secured tightly and the brake lever hanging loose. Now install the Brake rod extension, threading the male end to the original brake rod. Don’t tighten this end yet Place the clevis over the forward most end of the brake rod extension, and threat the clevis nut onto the end of the rod. Bring the brake rod upright, to meet with the clevis at the end of the brake rod extension and replace the pivot pin. Before reinstalling the cotter pin, check the angle of the brake lever, to insure that you have the brake pedal where you want. If necessary, adjust the extension rod in or out, until you are satisfied, and then reinstall the cotter pin into the pivot pin. Check the Brake switch wire and install a new cable tie if required. Note: Due to utilizing a thicker material, 1/2″ versus 3/8″ from our competitor, the Brake rod is now positioned at a greater angle. Even with the angle, braking performance is not affected, but if you wish to bring the master cylinder in line with the brake rod, do this. Loosen the rear, and remove the front Allen bolt. Then place two washers behind the front bolt, under the bracket, and then re-install the bolts To change the angle of the brake rod, 1) loosen and remove the two master cylinder bracket Allen bolts 2) insert two washers behind the front bolt (front of the bike), behind the master cylinder bracket 3) tighten both bolts. Do not install any washers on the rear mounting hole. This will make the angle of the Brake Rod less aggressive. Step Two – Left Side For the left (Shifter) side, 1) use an open-end 10 mm wrench, to unscrew the two nuts that hold the shift rod in place. PLEASE note that one end of the shift rod has a left hand threaded nut. SAVE the nuts, as you will need them on the new longer Polished Stainless Steel Shift Rod. 2) Remove the stock shift rod. 3) Then using a 14mm socket or box-end wrench, remove the two bolts that hold the shifter floorboard/footpeg assembly (whichever your bike has) to the frame.

Incoming search terms:

YAMAHA V-Star 650 BIG AIR KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 21-01-2012

download
Remove fuel tank and air filter assembly per Yamaha service manual procedures. 2. Remove the air silencer box under the tank. 3. Install supplied BA-2410-00 Needle/Jet kit according to the instructions in the jet kit package being sure to use the Jets and Needle Slot setting called out for the external BAK filter assemble. 4. Reinstall the air silencer box under the tank. 5. Remove the rubber boot from the stock air box. It is glued-in from the factory, but will come loose if gently persuaded. See photo #1 Our install guides provide a basic outline on the proper installation of our products. Further tuning and/or fitment may be required. Barons bears no responsibility on installation costs associated with this product. © 2010 Barons Custom Accessories 7401 Slater Ave. Huntington Beach, CA 92647 (714)274-4065 – Ph. (714)848-0718 – Faxwww.baronscustom.comtech@baronscustom.com Page: 2 BA-2011-00/03/06/07/13/13B BIG AIR KIT – YAMAHA V-Star 650 6. Install the stock rubber boot into your new Baron air filter backing plate with the supplied glue. Squeeze glue liberally into sealing groove in stock rubber boot. See photo #2 Allow glue to set up and dry prior to mounting onto bike

Incoming search terms:

Incoming search terms: