v star 950 coil cover

You search Auto repair manual PDF v star 950 coil cover, if there are search results will appear below. If search results do not exist, please search by others keyword.



  v star 950 coil cover Direct Download speed 5282 Kb/s

  v star 950 coil cover Full Version speed 6162 Kb/s



V-Star 1100 And Dragstar 1100 Modification V-Star Driving/ Passing Lights Factory Chrome Light Bar Cover Installation

0

Filed Under (Yamaha) by admin on 08-11-2010

download
Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. Use a rotary tool to widen the fastening area of the lower backside clips on the cover. The total width between the clips should be 4 æ inches. Trim off º inch on both inside ends of the lower backside attachment clips. Trim the clips equally. The following picture shows a modified cover. Narrow the clips on both ends to fit over the welds on the bar. The cover will not attach to the bar if the width between the clips is too narrow. If the width is too wide the cover may slide sideways on the bar. Narrow both clips equally to center the cover over the welds on the lower edge of the bar. The top of the cover is modified to allow the cover to fit over the bolts on the light bar. The top edge of the cover is filed æ inch deep and 5/8 inch wide to fit over the bolts. The back top edge is filed or ground 1/8 inch to fit over the light bar fastening bracket. Use care when filing chrome covered plastic. The following picture will help to complete this step in the modification. Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. The ends of the cover are modified to allow the cover to fit over the upward curved light bar. The upper openings on the ends of the cover that fit over the bar must be filed to enlarge the area. Grinding the cover ends will allow the cover to fit and clip onto the bar. The end openings are filed or ground at an angle to match the slope of the bar. This picture shows the outer end of the cover. The ends of this cover have been modified by enlarging the area on the upper edges to fit over the upward curving light bar. The ends must be enlarged 1/8 inch on the top edge. The cover edge can be slanted upward to match the curved bar. Modify the cover ends until it fits without the outer chrome cover touching the bar. Modify your factory light bar cover to fit on Yamaha brand driving/passing lights. Sometimes the modified light bar cover may touch the bottom of the headlight. Modify the cover, or adjust the bar or headlight if you notice the headlight touching the bar cover. This modification makes the V-Star motorcycle with Yamaha driving lights look better. The light bar bolts are covered and the chrome cover improves the appearance of the front of your bike. Other V-Star riders will notice how nice the front of your bike looks with the chrome light bar cover installed

Incoming search terms:

HARLEY DAVIDSON DYNA CHROME COIL COVER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 06-03-2011

download
Installation 1. Refer to the Service Manual and follow the instructions given to remove the maxi-fuse. 2. Note the position of each spark plug wire in the ignition coil, then disconnect the two wires. 3. If there is an existing coil cover: Remove and discard the coil-cover mounting screws and spacers. Remove and discard the coil cover. If there is not an existing coil cover: Remove and discard the two coil mounting screws. 4. See the Service Parts illustration. Obtain the coil cover bracket (3), two long screws (4) and two spacers (2) from the kit. 5. Insert the screw into one of the holes in the bracket as shown, through a spacer, and into a coil mounting hole. Repeat with the second screw and spacer. 6. Assemble the coil to the electrical caddy with the two screws. Tighten the screws to 50 in-lbs (5.6 Nm). 7. Obtain the new chrome coil cover (1) from the kit. Position the cover over the coil, and fasten to the coil cover bracket with the three chrome screws (6) and washers (7) from the kit. Do not fully tighten the screws at this time. 8. Connect the spark plug wires through the holes in the side of the coil cover onto the correct coil terminals. 9. Adjust the cover to center the spark-plug wire boots in the coil cover holes for best appearance. Tighten the three chrome screws securely 10. Refer to the Service Manual and follow the instructions given to install the maxi-fuse

Incoming search terms:

YAMAHA V-Star 1100 Motorcycle Enhancements Remote Oil Filter Installation Manual

0

Filed Under (Yamaha) by admin on 10-11-2010

download
Removing Your Old Filter and Beauty Cover In order to install the new Remote Oil Filter Kit, you’ll need to remove the stock Yamaha “beauty cover” and the old filter and filter cover. Remove the engine parts necessary to access the stock filter as outlined in the V-Star owner’s manual. The parts should come off in this order: 1. Muffler assembly 2. Front exhaust pipe 3. Rear brake reservoir cover bolt and brake cover (the reservoir should not be removed, it can remain in place and be moved aside as needed) 4. Right floorboard (this can be simply loosened, by loosening the two bolts underneath) With the above parts removed, you can remove the Allen bolts holding the beauty cover and filter cap from your engine. There are five Allen bolts holding the beauty cover (so named, because most of the cover just covers the chromed side of the engine There are five bolts holding the cover. Ignore the three on the “Yamaha” cap in the middle – these just hold the Yamaha cap to the beauty cover itself. One bolt is hidd – in this picture – just be the Yamaha ca en low p. The bottommost bolt on the beauty cover will likely leak some oil when you remove it – it holds on the inner oil filter cover. Once you remove the beauty cover, you can remove the oil filter cover, and the oil filter Keep these two “O” rings, you’ll need them for the remote kit Old oil filter. Toss it away; you’ll never need one again! Throw away the old filter, and carefully remove the orange and black “O” rings from the filter cover (see picture above). These two “O” rings will go on the new engine cap in the same order as on the old filter cover. “O” ring for bottom bolt. When the beauty cover and filter cover are removed, be sure not to lose the tiny “O” ring that the bottom bolt goes through. Preparing the Remote Oil Filter Kit Remove the orange and black “O” rings from the stock filter cover plate, and place them on the Remote Oil Filter Kit engine cap – black on the inside, orange on the outside – just like on the stock filter cover.

Incoming search terms:

HARLEY DAVIDSON DERBY COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
These kits are designed for installation on all 1999 and later 1340 Evolution and Twin Cam equipped models.INSTALLATION For models equipped with left side exhaust pipe: Perform this installation when the engine is cool. Working on or near the exhaust system when the engine is hot could result in severe burns. (00311a) NOTE Remove clutch inspection (derby) cover with motorcycle upright, not on side stand. If cover is removed with motorcycle on side stand, primary fluid will leak out of primary chaincase. 1. On models so equipped, remove the left-side passenger footboard. Using a T27 TORX® drive head, remove the derby cover from the primary chaincase. Discard the derby cover and fasteners. NOTE The gasket between the clutch inspection cover and the chaincase cover must be removed and all oil must be wiped from the gasket and groove in chaincase cover each time the cover is removed. 2. Remove the gasket from the groove in the chaincase cover and mounting surface. 3. Inspect gasket for tears or damage. Replace as required with gasket 25416-99C (sold separately). NOTE If installing the Derby cover on a 2006 and later Dyna, 2007 Softail, or 2007 Touring model, the original equipment gasket must be discarded and replaced with Derby Cover Gasket 25416-99C (sold separately). 4. To avoid punching holes in the clutch inspection cover gasket or enlarging the existing holes, install the new derby cover and gasket as follows: a. Align the triangular shaped hole in the gasket with the top hole in the derby cover. Be sure the rubber molding and the words “towards clutch” face the motorcycle. b. See Figure 2. Place a washer (2) from the kit onto the threads of one of the new screws (3). Insert the screw threads through the top hole in the derby cover, and carefully thread it all the way through the triangular shaped hole in the gasket. Do not push the screw through the hole. c. Hang the derby cover on the primary chaincase cover flange by starting the top cover screw. d. Start the remaining four screws and washers. 5. Install gasket (part number 25416-99C) and derby cover (1) on primary chaincase cover using screws and washers from the kit. Tighten screws to 84-108 in-lbs (10-12 Nm) in the sequence shown in Figure 1

Incoming search terms:

HI-4 DUAL FIRE MOTORCYCLE IGNITION INSTALLATION INSTRUCTIONS

0

Filed Under (Yamaha) by admin on 09-11-2010

download
Turn ignition switch off and disconnect battery ground cable. 2. Refer to Figure 3. Remove OE ignition module and wire harness (items 1-4). You will disconnect two wires at the coil (15), a wire going to the VOES (Vacuum Operated Electrical Switch) (18), a black ground wire at the ignition module, and the 3 pin plug (20) that connects to the sensor plate (11). Refer to shop manual for locations. 3. Remove ignition cover plates and gasket (items 5- 9). This will require drilling out two rivets. The rivets will later be replaced with two supplied self- threading screws. 4. In order to remove the sensor plate cable, the cable plug (20) must be removed first. Use needle nose pliers to pull the terminals out of the plug. Then pull the cable through the exit hole at the bottom of the timing cover. 5. Note location of sensor plate (11). There is a V notch in the sensor plate used for alignment. When you install the HI-4, you should align the V notch in the same location. This should set the timing close enough to start the engine. Remove and save the two standoffs and washers (10). Remove the sensor plate (11). HI-4 INSTALLATION Refer to Figure 4. The HI-4 requires use of the OE timing rotor P/N 32402-83 (used only on 1985 and newer models). If you have an older model or are not sure, check the rotor (9) for the correct part number. For models prior to 1980, use the supplied 10-32 x ¾”bolt and washer to mount the rotor. 1. Install the HI-4 system in place of the OE breaker or sensor plate. Rotate the HI-4 about 90 degrees to give better access to the cable exit hole. Install the HI-4 first, then push the cable through the hole. On some early models it may be necessary to enlarge the wire harness exit hole in the gear cover. Align the V notch on the HI-4 same as the OE plate you removed. Use the OE standoffs to secure the HI-4. You must use lockwashers under the standoffs for proper clearance between the HI-4 and cover plate. Do not fully tighten the standoffs until the timing has been set. 2. Route the HI-4 wire harness along the frame rails up to the coil. Make sure that harness will not be chafed or burned by exhaust heat. Secure harness with tie wraps. Do not install timing cover. HI-4 HOOKUP Crimp terminals and hardware are supplied for your convenience. Use the ring terminals for coil hookup. Use male-female quick disconnects for connections to the tach and vacuum switch (VOES). Tape up any unused wires. 1. Circuit Breaker Cover Screws (2) 2. Circuit Breaker Cover 3. Circuit Breaker Cover Gasket 4. Breaker Plate Screws (2) 5. Breaker Plate Screw Lockwashers & Washers (2 each) 6. Retainer (1971 to early 1972) 7. Circuit Breaker Cam Bolt 8. Breaker Plate Assembly 9. Breaker Cam 10. Advance Assembly 11. Gear Case Cover 11 10 9 8 7 6 5 4 3 2 1 NOTE: Damage will result if the brown tach wire comes in contact with +12V. Figure 1. Harley-Davidson®OE Points System
9000-4002A REV A 3 2/05 1. Identify switched +12 volt wire and tach wire (if equipped) going to the coil. Refer to your service manual, or reconnect the battery and use a test light or voltmeter. The switched +12 volt wire will be hot when the ignition key is turned on. 2. Refer to Figure 5. Connect the HI-4 red wire and switched +12 volt wire to Coil positive. 3. The HI-4 white wire is not used and should be taped. 4. Connect the HI-4 black wire to the Coil negative terminal. 5. Connect the HI-4 green wire to the vacuum switch (Figure 3, item 18), if used. 6. Connect the HI-4 brown wire to the tach wire, if equipped with tach. Tape up if unused. 7. The HI-4 is grounded via the timing housing; a separate ground connection is not required. 8. Reconnect battery ground cable. Verify proper ground connections to the frame and engine. VOES HOOKUP The OE vacuum switch (VOES) is normally an open circuit. Above 3-5 inch-Hg vacuum, the VOES closes and grounds the vacuum input on the OE ignition module. This increases the total advance generated by the OE ignition module. Vacuum advance improves part throttle 17 16 1. Cover Screws (2) 2. Ignition Timer Cover 3. Ignition Module 4. Timer Plate Screws (2) 5. Washers (2) 6. Screws & Washers (2 each) 7. Shield 8. Sensor 9. Trigger Rotor Bolt 10. Timer Plate 11. Trigger Rotor 12. Advance Assembly 13. Gear Case Cover 14. Ignition Coil 15. Spark Plug Wires (2) 16. Ignition Coil Terminal (FX) 17. Ignition Coil Terminal (FL) 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 NOTE: Most motorcycle coils do not have terminals marked. Use either terminal for Coil+ (positive) and the other one for Coil- (negative). Warning: The HI-4 (8-1100) Dual Fire ignition will not work with 2 plugs per head, dual coil application. Damage will result if attempted. Use the HI-4 (8-2100) single fire ignition for 2 plugs per head applications

Incoming search terms:

HARLEY DAVIDSON ENGINE/ TRANSMISSION INTERFACE AND TOP COVER INSTALLATION

0

Filed Under (Harley Davidson) by admin on 25-12-2010

download
1. Refer to the Owner’s Manual and follow the instructions given to remove the maxi-fuse. 3 1 2 is02998 1. Transmission top cover screw (4) 2. Oil spout assembly screw 3. Upper bearing housing screw (2) Figure 1. Interface Cover Installation 2. See Figure 1. Remove and retain the four socket head cap screws (1) that fasten the front and right side of the transmission cover. See Figure 3. Obtain the chrome top interface cover (3) from the kit. NOTE The top interface cover can be carefully brought into position on top of the transmission housing from either the right or left side without removing or loosening any vehicle components. 3. Position the top interface cover over the transmission top cover. Loosely fasten the chrome cover to the top of the transmission housing with the screws removed in Step 2. 4. Obtain the chrome filler neck cover (4), 1/4-20 socket head screw (5), flat washer (6) and spacer (7) from the kit. Remove the oil level dipstick from the oil spout on the side of the transmission housing, wipe off and set it aside for later installation. NOTE Insert a clean shop rag into the oil spout opening while the dipstick is not installed. With the dipstick removed, small parts or other foreign material could fall into the transmission, leading to equipment damage or malfunction. 5. See Figure 1. Remove and discard the socket head cap screw (2) that fastens the oil spout assembly to the transmission housing. DO NOT remove the oil spout from the vehicle. 6. Place the flat washer over the threads of the new screw, and insert the screw into the unthreaded hole in the chrome filler neck cover. Place the spacer onto the screw threads. Apply a few drops of Loctite® 243 (Blue) to the screw threads, and position the chrome cover onto the oil spout on the transmission housing. Lubricate the filler neck gasket with soapy water to aid in installation. Tighten the screw to 84-132 in-lbs (9.5-15 Nm) . 7. See Figure 3. Obtain the chrome lower side interface cover (1), one #10-24 socket head screw (8) and one chrome flat washer (9) from the kit. NOTE For models with mid controls, the right-side rider footrest (foot peg) support bracket must be loosened to allow installation of the lower side interface cover. After the cover has been installed, tighten the footrest bracket attaching screws to 25- 35 ft-lbs (34-47 Nm) . 8. Position the cover around the chrome filler neck cover installed in Step 6. Loosely fasten the cover to the threaded hole in the filler neck cover with the screw and washer. 9. Obtain the chrome upper side interface cover (2), three #10-24 socket head screws (8) and three chrome flat washers (9) from the kit

Incoming search terms:

HARLEY DAVIDSON CHROME SEAT POST REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
REMOVE 2 1 is00000 1. Seat Post 2. Screw Figure 2. Lower Seat Post 1. Refer to Owners Manual to remove the seat. To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect negative (-) battery cable before proceeding. (00048a) 2. Disconnect battery negative cable. 3. On motorcycles equipped with oxygen sensors, disconnect the rear sensor connector. 4. See Figure 2. Remove screw (2) and washer from the lower seat post (1) and discard. -J04294 1 of 2 5. Disconnect spark plug wires and primary wire from ignition coil. 6. See Figure 3. Loosen the bracket screws (1). Remove seat post screw (2) and seat post with ignition coil and cover. 7. See Figure 4. Remove coil cover screw (5) and cover (4) from stock seat post (1). 8. Remove ignition coil screws (3) and coil (2) from seat post. 2 1 is04241 1. Bracket Screws 2. Upper Seat Post Screw Figure 3. Upper Seat Post Fasteners 2 5 1 3 4 is04337 1. Seat Post 2. Ignition Coil 3. Coil Screw 4. Coil Cover 5. Coil Cover Screw Figure 4. Install Ignition Coil to Seat Post INSTALL 1. See Figure 4. Install ignition coil (2) to new seat post using screws (3). Tighten ignition coil screws to 10-15 ft-lbs (13.6-20.3 Nm) . 2. Install coil cover (4) to seat post with screw (5) and tighten to 30-40 in-lbs (3.4-4.5 Nm) . 3. See Figure 1. Place seat post (1) in position and attach lower post with screw (2), washers (3) and dome nut (4). Tighten screw (2) to 10-15 ft-lbs (13.6-20.3 Nm) . 4. See Figure 3. Attach upper seat post with screw (2). Tighten screw (2) to 12-15 ft-lbs (16.2-20.3 Nm) . Tighten bracket screws (1) to 12-15 (16.2-20.3 Nm) . 5. Connect primary wire to ignition coil. 6. Connect spark plug wires to ignition coil. The rear cylinder plug wire attaches to the top coil post. Ensure that spark plug wire boots are fastened securely. 7. Connect rear oxygen sensor connector, if equipped. 8. Reconnect battery negative cable

Incoming search terms:

HARLEY DAVIDSON SOFTAIL TRANSMISSION TOP-COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 03-02-2011

download
INSTALLATION – TOP COVER 1. See Figure 3. Remove and retain the stock screw (J) from the top of the transmission upper cover (I). 2. Ease the left side of the cover through the right side of the engine. You may need to angle the transmission cover slightly as you work it into position. 3. Fasten the weld-nut end of the top-cover bracket (2) to the top cover (4) using the screw (3) from the kit. Torque the screw to 6.6 – 9 ft-lbs (8.9 – 12.2 Nm). 4. Fasten the top of the top-cover bracket (2) to the left side of the transmission upper cover using the screw (J) removed in step 1. Torque the screw to 8 – 10 ft-lbs (10.8 – 13.5 Nm). 5. Install the Softail transmission-interface cover (D). Go to the next section in this instruction sheet. NOTE Save the washer (1) from this kit for transmission-interface cover installation. INSTALLATION – INTERFACE COVER 1. See Figure 1. Remove the screw (1) from interface cover at location 1. Keep the screw for installation. 2. Loosen the screw (2) at location 2 approximately three turns. 3. See Figure 2. Position the slotted hole (1) on the interface- cover mounting bracket (2) behind the washer at location 2. 4. Install the screw (4) from Step 1 through the mounting hole on the bracket and into location 1. Tighten the screw to 7 – 9 ft-lbs (9.5 – 12 Nm). 5. Tighten the screw (3) in location 2 to 13-16 ft-lbs (17.6 – 21.7 Nm). 6. See Figure 3. Place the interface cover (D) in position on the motorcycle. Spread the oil-line grommet (E) to wrap around the oil lines, then re-position the grommet in the interface cover. The edge of the interface cover must overlap the top of the top cover

Incoming search terms:

HARLEY DAVIDSON VRSC FUEL TANK SIDE COVER KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 05-02-2011

download
INSTALLATION 1. Note the left and right areas on frame where the covers will be installed. Using a 50/50 mixture of isopropyl alcohol and water, thoroughly clean the frame tubes surrounding the fuel cell on the left and right sides. Let dry completely. 2. Unlock and open seat. NOTE Loosening the ignition/light switch screw (in the following step) will allow much easier alignment of the ignition/light switch cover and ignition/light switch during installation. 3. See Figure 1. At area inside of frame rail just above the ignition/light switch housing, loosen the ignition/light switch screw just enough to allow the ignition/switch switch to move slightly from side to side and up and down. Do not completely remove screw 4. See Figure 4. Obtain the right side cover bracket (ignition/light switch side) from kit. 5. Remove the strips protecting the adhesive at all of the raised sections on the cover. 1 2 is 02045 1. Ignition/Light Switch Screw 2. Ignition/Light Switch Figure 1. Loosen Ignition Switch Assembly 6. See Figure 2. Carefully align the right side cover between the three frame tubes. Beginning with the left portion of the cover, press the cover between the upper and lower frame tubes until the raised portions of cover (with adhesive) begin to snap into place. While carefully aligning the right portion of the cover, move the ignition/light switch as necessary until centered within hole in cover, then firmly press into place. Adjust ignition/light switch until the switch is centered within cover. Make sure all raised locations (with adhesive) are firmly contacting the upper and lower frame tubes and that cushion rests against front vertical frame tube. 7. See Figure 1. Tighten the ignition switch screw to 6-10 Nm (53-88 in-lbs ) . NOTE The right side (ignition/light) switch cover surface can be damaged by the key fob (from vibration) when the key is in the ignition and the bike is running. You can either remove the key fob so it does not damage the cover surface, or you can install the plastic clear sheet (included in kit) onto the side cover for protection. 8. If desired, perform the following to install the plastic clear cover onto the ignition/light switch cover. a. Obtain the plastic (rhino) sheet and hold up to the switch cover to determine proper orientation and spacing. b. Carefully peel the adhesive backing from the plastic sheet and position onto the cover. Use a wet sponge, and working out from the center, rub out any bubbles or overlapped areas under the sheet. Allow to dry completely.

Incoming search terms:

HARLEY DAVIDSON TIMER COVER KITS INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 21-02-2011

download
INSTALLATION Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) NOTE For kits 32972-04A, 32924-04A, 32675-04A, and 32923-04A, refer to step 1 and 2 for installation instructions. To prevent accidental vehicle start-up, which could cause death or serious injury, remove maxi-fuse before proceeding. (00251a) 1. See Figure 2. Remove and discard the original screws and timer cover. 2. Place new timer cover (1) in position and secure with chrome screws (2). NOTE For kits 32584-88TA, 32668-98A, and 32571-98A, refer to steps 3 through 8. 3. Use a 3/8 in. drill bit and drill the heads off the original timer cover rivets. Remove original timer cover. NOTE If the inner timer cover has been riveted in place and access to the cam position sensor is required, use a left hand drill and carefully remove the rivet heads. If a right hand drill is used, the sensor plate screw heads could break off when trying to remove the rivet. NOTE To make the cam position sensor tamper proof, follow steps 4 through 6. If the cam position sensor is not required to be tamper proof, skip steps 4 through 6. 4. Remove and discard inner cover retaining screws. Leave gasket (if used) and inner cover in position. 5. See Figure 1. Place washers (4) over rivets (3) and place rivets into inner cover holes so the backs of the rivets go into the sensor plate screws’ tapped holes. 6. Use a standard rivet tool and install rivets, securing inner cover to sensor plate screws. 7. Use the self-tapping screw (5) to cut threads into the remaining inner cover holes. Discard screw after use. 8. Place new timer cover (1) in position over inner cover (A) and secure with chrome screws (2). NOTE For kit 32581-90TB, refer to steps 9 and 10. 9. Use 3/8 in. drill bit and drill the heads off the timer cover rivets. Remove original timer cover. 10. Place new timer cover in position and secure with chrome screws (Part Number 9462) from kit

Incoming search terms: