v twin yamaha carb leaks gas

You search Auto repair manual PDF v twin yamaha carb leaks gas, if there are search results will appear below. If search results do not exist, please search by others keyword.



  v twin yamaha carb leaks gas Direct Download speed 5282 Kb/s

  v twin yamaha carb leaks gas Full Version speed 6162 Kb/s



KAWASAKI 1500 CARB THUNDER Air Filter Kit Installation And removal Instruction

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
1) Remove Seat 10mm KAW 1500 CARB ADPTOR QTY PARTS LIST 1 1500 CARB ADAPTOR 1 3″ PIECE OF HOSE 1 DOUBLE BARB 1 L-BARB 1 3/8″ RED PLUG 1 ¼” BLACK VACCUM PLUG 1 M6-1 NYLON INSERT LOCK NUT 3 M6-1 X 16 FLAT SOCKET HD CAP SCREW 1 170 MJ 1 INSTRUCTIONS 2) Remove Dash Plaque 8mm bottom Bolt only 3) Lift from bottom then Remove speedo cable 4) Disconnect Electric Plugs 5) Remove 12mm bolts holding tank 6) Turn petcock OFF – Pinch off fuel line. 7) Disconnect the electric Plug under speedo opening 8) Lift Tank at Rear – Disconnect two Vent Lines; Fuel gage Vent will Pull up – Remove. 9) Remove Chrome Air Cover. 10) Left side Remove two screws – 10mm bolt in side Air box. Pull hoses off Remove 1″ hose going to cross over Tube. 11) Remove two 8mm bolts on Bracket – Remove Bracket 12) Remove Screw on Top of air Box Snorkel 13) Remove both side covers 14) Remove air Backing plate right side (Crank Case Breather hose that connects to stock air box will connect to new) 15) Remove Bracket that holds Carb and holds Backing Plate 16) Take idle adjustable Knob loose – let hang loose 17) Take Choke Knob out of holding Bracket 18) Hose that went to cross over tube MAY BE PLUGGED OR VENTED your Choice (Fresh air unit) ** 98′S or any models with carb warmer should disconnect carb warmer by pinching off line on each side of connector that plugs into carb on bottom. Small bracket with one screw directly on the bottom of carb. 19) Loosen Clamp that holds Carb to intake Manifold, Carb will hang loose 20) Remove intake Manifold 5mm Allen- Remove crossover tube. 21) (- BE CAREFULL-) LINE IT UP RIGHT- Replace intake Manifold (YOU MAY TO SEAL THIS WITH A SEALER LIKE PERMATEX) ( BE SUPER CAREFUL TO KEEP INTAKE COVERED DURING EACH STEP. SCREWS CAN FALL ONTO INTAKE) 22) Drain Float Bowl 3mm allen – very bottom of carb 23) Remove Float Bowl 4 screws (#2 Phillips) let hang down 24) Remove main jet, if Emulsion tube comes out use 8mm and Flat tip to separate jet from Emulsion tube. 25) Install with new jet 26) CAREFULLY Reinstall Float Bowl Cover 27) If installing Needle Remove Top Cover of Carb, Carefully pull the slide out. ( BE CAREFUL WITH DIAPHRAM) Remove Spring + Needle Install new Needle (WE RECOMMEND THE 3RD CLIP FROM TOP WITH TWO WASHERS ON TOP. REINSTALL 28) Be sure to reseat diaphragm – BE CAREFUL Reinstall Cover. 29) Install Carb to Intake – reconnect carb warmer if applicable 30) Reattach idle adjustment 31) Reattach Choke 32) Reattach Bracket in front of Carb- 33) Take Center bolt mount Rubber Gromlet from Stock Air box Plate install in to new Air box Adapter use stock Bolt, Attach to Bracke

Incoming search terms:

HW Prowler Carburetor Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
1. Remove both seats and the plastic seat pans under the seats. 2. Remove the engine cover 3. Remove the air-box by removing the cross-bar support that runs under the air-box to the framing on each side by the seat framing and disconnect the air box from the carburetor and from the plastic intake in the rear. 4. Disconnect the engine breather hose from the bottom of the air box 5. Set the air-box to the side 6. Disconnect the plug going to the stock carburetor, this is the electronic choke. Wrap the end left on the vehicle with electrical tape. 7. Cut the fuel line just above the fitting on the passenger side of the carb 8. Remove the side cover off the drivers side of the carb where the throttle cable goes in, see fig. #1 9. Pull the throttle cable out and then remove the throttle cable end from the throttle plate See Fig. #2 10. Loosen the clamp on the rear of the carb holding the carb on 11. Pull the carb out of the intake boot 12. Set OE carb to the side. 13. Push the new Carb into the intake boot making sure the carb is perfectly vertical and then tighten the clamp back up. The new carb is slightly larger than the stock one so some additional pressure will be needed to get it in. 14. Route all the breather lines connected to the carb down under the carb. 15. Connect the throttle cable onto the new carb but putting the cable end in the bottom hole of the throttle plate on the passenger side of the carb allowing the cable to ride in the slot in the plate and then turn the throttle plate clock wise allowing the threaded end of the cable to fit into the lower round hole of the throttle cable connection plate. See Fig. #3 16. Make sure you have a nut on each side of the plate turn the nut on the outside of the plate to take up the slack in the throttle cable then tighten the nut on the inside of the plate. See Fig. #3 17. Push the fuel line onto the fuel inlet on the passenger side of the carb and install the supplied clamp to hold it on. The fuel line will be a little hard to push on. 18. DO NOT ATTEMPT TO INSTALL THE CHOKE CABLE PARTS SUPPLIED IN THE KIT UNTIL AFTER THE CHOKE CABLE ITSELF IS INSTALLED AND READY TO SCREW INTO THE CARBUETOR. 19. To install the supplied choke cable, drill a 3/8″ hole in the dash on the left side of the steering wheel in a location convenient to your left hand. 20. Remove the plastic nut from the bottom of the choke handle on the choke cable. 21. Push the choke cable thru the hole you drilled and then slide the nut over the cable to the inside of the dash and reinstall back on the back of the choke mechanism. Some dash screws maybe needed to be removed to accomplish this

Incoming search terms:

2009 GAS GAS TXT PRO TECHNICAL SPECIFICATIONS AND OWNER'S MANUAL

0

Filed Under (Gas Gas) by admin on 28-11-2010

download
ENGINE 2 stroke, single cylinder, direct reed valve crankcase induction. Liquid cooled. 125 cc. engine Cylinder size 124,8 cc. Bore and stroke 54 x 54.5 mm. 200 cc. engine Cylinder size 175,3 cc. Bore and stroke 64 x 54,5 mm. 250 cc. engine Cylinder size 247,7 cc. Bore and stroke 72,5 x 60 mm. 280 cc. engine Cylinder size 272,2 cc. Bore and stroke 76 x 60 mm. 300 cc. engine Cylinder size 294,1 cc. Bore and stroke 79 x 60 mm. Carburettor, diameter of the diffusor 26 Lubrication system Mixture (50:1)(2%) Ignition system Digital magnetic flywheel CDI TRANSMISSION Transmission type 6 gears, Four / Six system by GAS GAS* (Patented). Clutch type Hydraulic command, 1/3 discs, variable progressive with diaphragm system by GAS GAS* (Patented). Driving system By chain Gear ratio 1st. 2,996 (35x27x28/16x24x23) 2nd. 2,571 (36/14) 3th. 2,187 (35/16) 4st. 2,112 (36x23x24/14x28x24) 5st. 1,125 (27/24) 6th. 0,821 (23/28)
-11- Primary reduction ratio 2,777 (75/27) Final reduction ratio 3,818 (42/11) Overall drive ratio 8,704 (6th. gear) Transmission oil Capacity 550 cc. Type 10W40 API SF o SG. FRAME Type Tubular profile made with Cr-Mo. Tyres Front 2,75 x 21″ Trial Rear 4,00 x 18″ Trial tubeless. Suspension Front Adjustable tele-hydraulic fork ø 40 mm. (125 / 200). Adjustable tele-hydraulic fork ø 40 mm with aluminium bars (250 / 280 / 300) Rear Variable progressive system with mono-shock multiadjustable. Suspension stroke Front 177 mm. Rear 164 mm. Front fork oil SAE 5. Front fork oil level ø 40 mm.(125 / 200) 180 mm. air chamber steel bar ø 40 mm. (250 / 280 / 300) 160 mm. air chamber aluminium bar BRAKES Type Disc brake. Disc diameter Front ø185 mm. 4 piston calipers. Rear ø150 mm. 2 piston calipers. DIMENSIONS Overall height 1180 mm. Overall width 820 mm. Seat height 650 mm. Ground clearance 315 mm. Wheelbase 1330 mm. Fuel tank capacity 3,1 liters.

Incoming search terms:

42MM MIKUNI FLATSLIDE CARBURETOR INSTRUCTIONS

0

Filed Under (Mikuni) by admin on 31-10-2010

download
To install, remove the stock carb per Yamaha shop manual procedures. Remove stock throttle cables. Install Mikuni HSR carb into intake manifold and tighten manifold clamp. Install new HSR series throttle cables and adjust cable slack per Yamaha shop manual procedures. Hook fuel line to HSR carb and fasten clamp.* Start motorcycle and fine tune HSR carb for proper running per supplied Mikuni tuning manual. *NOTE: Mikuni HSR series carburetors are designed for gravity-feed fuel systems. You should bypass your stock fuel pump and directly feed your HSR carb right from the fuel petcock. We have noted, though, that you may not be able to get good fuel flow from your Road Star fuel tank in low-fuel situations. You may run your stock fuel pump with the HSR carb, but to do so requires the purchase and installation of an adjustable fuel pressure regulator (set at 1/2 to 1 lb. of pressure). These are available from most auto parts stores. The stock carb has 2 wires running to the lower rear of the float bowl , these were for a carb warmer, they are not used in this application. Unplug these wires at the main wire harness and retain with your stock carb. The Road Star ignition system uses data from the stock throttle position sensor (TPS) to manage your ignition timing. It is necessary to give the bike this information. You may do so by removing the TPS sensor from the stock carb, leaving it plugged into the main wire harness (the sensor must be fixed to a closed-throttle position), or you may locate the plug for the TPS on the main wire harness and test the leads – you will find one ground, one with .5V and one with 1.5V. Connect the 1.5V to the ground and this will give the bike the same information as stock fully closed throttle. The output of the OEM fuel pump is too high and will cause fuel overflow in the HSR carb, resulting in a possible dangerous fire hazard

Incoming search terms:

Harley-Davidson Big Twin Evolution and Twin Cam Edelbrock/ JE Sport INSTALLATION INSTRUCTIONSsman Pistons

0

Filed Under (Harley Davidson) by admin on 07-02-2011

download
INSTALLATION PROCEDURE Note: All Evolution® “Big Twin” pistons are marked “Front” or “Rear” and come with rings, wrist pins, and locks. • Note: We highly recommend that a dealer or trained mechanic perform the installation of these pistons. Specialized equipment is required for honing and finishing the cylinders to ensure long life of the piston and cylinder assembly. 1. Remove original equipment cylinders from engine. Refer to a shop manual or other reference book for specific steps, if needed. (Note: Care should be taken not to bend the studs or damage the cylinder during removal of the cylinders.) 2. With a small screwdriver, move the wrist pin retainer around to gain access to the tail of the retainer as it lines up with the notch in the bottom of the wrist pin hole. 3. Use a small screwdriver, pick or awl to roll the wrist pin retainer out of its groove. 4. Push wrist pin out and remove piston. 5. Repeat procedure for the other piston. 6. At this point, take cylinders, new pistons, and piston-to-wall clearance specifications to your dealer or machine shop to perform necessary machining operations. • IMPORTANT NOTE (Evolution® and Twin Cam®): The cylinder bore must be machined/honed to provide .0025″ of piston-to-wall clearance. Measure the piston diameter at a point .500″ up from the lower skirt (See Figure 3). 7. Starting with the front cylinder, install new piston rings and one wrist pin retaining clip (Note: Second ring has a dot which must face up when the ring is installed) . 8. Place the piston over the conecting rod, making sure that the intake valve pocket is towards the intake side. (For Evolution ® , see Figure 1. For Twin Cam ® , see Figure 2) . Coat the wrist pin with engine oil and insert it into the piston. Install the second wrist pin retainer into the groove. 9. Lightly coat the piston skirt with engine oil. Place a piston ring compressor over the piston/ring assembly and compress. Place the cylinder over the piston and gently push down until all rings are in the cylinder. Remove the ring compressor, and push the cylinder the rest of the way down. (Note: Be careful not to get oil onto the base gasket.) 10. Place two nuts and washers on opposite corners of the #1 cylinder to hold it down while you repeat the procedure for cylinder #2. 11. Assemble the rest of the engine per factory specifications. Start the engine and let it run at 2000 rpm for about 10 minutes.

Incoming search terms:

KAWASAKI 1700cc Liquid-Cooled V-Twin Engine 6-Speed Transmission with Overdrive

0

Filed Under (Kawasaki) by admin on 13-12-2010

download
Kawasaki’s first production bagger model is ready to take the street by force. The new Vulcan® 1700 Vaquero™ motorcycle combines the authority of a massive 1700cc liquid-cooled V-Twin engine together with low-slung, streetwise styling of a frame-mounted front cowling and lower chin fairing, sleek side-opening hard bags, and a choice of stealthy Ebony or fiery Candy Fire Red monotone paint. Besides its unmistakable style, the Vaquero also includes a smooth-shifting 6-speed overdrive transmission, cruise control, a full-feature audio system, and a host of custom-designed accessories. Get ready to rumble. 1700cc Liquid-Cooled V-Twin Engine The Vulcan 1700 Vaquero’s 1700cc V- Twin bristles with low-rpm torque, ensuring immediate and potent acceleration. 6-Speed Transmission with Overdrive With its overdrive top gear, the Vaquero’s 6-speed transmission teams up with the V-Twin engine for a relaxed highway cruising experience. Frame Mounted Front Cowling Muscular front cowling features a cut-down windscreen for a minimalist look and uninterrupted airflow, and is frame-mounted for light handling. Side-Opening Hard Bags Holding an impressive 9.2 gallons of storage apiece, the side bags integrate neatly into the Vaquero™’s smooth, clean lines. Electronic Cruise Control Conveniently located on the right handlebar, the Vaquero’s standard electronic cruise control precisely maintains speeds between 30 and 85 mph. Full-Feature Audio System High-fidelity audio system features AM/FM and weather radio, and is can be accessorized with iPod players, XM Radio and CB radios. Multi-Function LCD Instrumentation Located on the Vaquero’s stylish “muscle car” inspired dashboard, the multi-function LCD instrumentation clearly organizes and presents all essential information.
Engine Four-stroke, liquid-cooled, SOHC, four valve per cylinder, 52° V-twin Displacement 1,700cc / 103.7ci Bore X Stroke 102 x 104mm Compression Ratio 9.5:1 Maximum Torque 108 lb-ft @ 2,750 rpm Cooling System Liquid, plus cooling fins Ignition TCBI with Digital Advance Induction Digital fuel injection, dual 42mm throttle bodies Transmission 6-speed with overdrive and positive neutral finder Frame Type Steel, double-cradle with box-section single-tube backbone Rake/Trail 30° / 7.0 in. Front Suspension / Wheel Travel 45mm hydraulic fork / 5.5 in. Rear Suspension / Wheel Travel Swingarm with twin air-assisted shocks, with 4-way rebound damping / 3.1 in. Front Tire Size 130/90×16 Rear Tire Size 170/70×16 Brakes, Front / Rear Dual 300mm discs, dual twin-piston calipers / Single 300mm disc, twin-piston caliper Overall Length 98.8 in. Overall Width 38.2 in. Overall Height 50.8 in. Seat Height 28.7 in. Curb Weight 835.7 lbs.** Wheelbase 65.6 in. Fuel Capacity 5.3 gal. Color Choices Ebony, Candy Fire Red Warranty 36 months Good Times™ Protection Plan 12, 24 or 36 months ** Curb weight includes all necessary materials and fluids to operate correctly, full tank of fuel (more than 90-percent capacity) and tool kit (if supplied

Incoming search terms:

TWIN VELOCITY FOR YAMAHA V-STAR 650 INSTALLATION MANUAL

0

Filed Under (Yamaha) by admin on 09-11-2010

download
STEP 1 Remove the stock air cleaner and components to the point shown in PIC. 1. The stock plastic airbox adapter “A” and stock mounting brackets “B” will remain in place. STEP 2 Insert both flanges of the rubber adapter through the mounting bracket as shown in PIC.2. The hardware components used for installation are placed near their respective mounting points: •”A” Socket head cap screw – 30mm long, tapered bolt cap, and two spacers. The spacers are placed between the chrome, and the stock mounting brackets. •”B” Socket head cap screw – 15mm long , tapered bolt cap •”C” Socket head cap screw – 30mm long, tapered bolt cap, two spacers (place between chrome and stock brackets), and flange nut. •”D” Mounting holes. STEP 3 The opening in the adapter boot must be slipped over the flange of the stock airbox and secured with the stock clamp. Install the mounting bracket as shown in PIC.3. Secure this assembly to the bike with the hardware specified in the previous step. STEP 4 Disassemble the Twin Velocity. Use 1/4″ 12 point combination wrench for the three fasteners that hold the front and rear sections of the Twin Velocity together. Pay close attention to the location of all components to simplify re- assembly. STEP 5 The 5/16″ button head bolts, reducer washers, nylon washers, flat washers, and acorn nuts will secure the air cleaner to the mounting bracket. See PIC.4. STEP 6 “Work” the radiused flange of the adapter through the inlet of the air cleaner. Using the hardware shown in the previous step, mount the air cleaner to the mounting bracket. See PIC.5. STEP 7 See PIC.6. Push two each of the oval rubber pads into the corresponding pockets in the air cleaner until they are flush with the back plate — two per side. You will find 3 holes behind the radiused flange that was previously installed through the air cleaner inlet in Step 6. With the three 1/4″-20 Socket head cap screws and nylock nuts secure the air cleaner to the mounting bracket. STEP 7 Reassemble the Twin Velocity Air Cleaner.

Mikuni HSR 42/ 45 Installation Instructions

0

Filed Under (Mikuni) by admin on 31-10-2010

download
To install, remove the stock carb per Yamaha shop manual procedures. Remove stock throttle cables. Install Mikuni HSR carb into intake manifold and tighten manifold clamp. Install new HSR series throttle cables and adjust cable slack per Yamaha shop manual procedures. Hook fuel line to HSR carb and fasten clamp.* Start motorcycle and fine tune HSR carb for proper running per supplied Mikuni tuning manual. *NOTE: Mikuni HSR series carburetors are designed for gravity-feed fuel systems. You should bypass your stock fuel pump and directly feed your HSR carb right from the fuel petcock. We have noted, though, that you may not be able to get good fuel flow from your Road Star fuel tank in low-fuel situations. You may run your stock fuel pump with the HSR carb, but to do so requires the purchase and installation of an adjustable fuel pressure regulator (set at ½ to 1 lb. of pressure). These are available from most auto parts stores. The stock carb has 2 wires running to the lower rear of the float bowl , these were for a carb warmer, they are not used in this application. Unplug these wires at the main wire harness and retain with your stock carb. The Road Star ignition system uses data from the stock throttle position sensor (TPS) to manage your ignition timing. It is necessary to give the bike this information. You may do so by removing the TPS sensor from the stock carb, leaving it plugged into the main wire harness (the sensor must be fixed to a closed-throttle position), or you may locate the plug for the TPS on the main wire harness and test the leads – you will find one ground, one with .5V and one with 1.5V. Connect the 1.5V to the ground and this will give the bike the same information as stock fully closed throttle.

HARLEY DAVIDSON LOCKING FUEL FILLER CAP KIT REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 11-02-2011

download
INSTALLATION 1. Prior to installing the gas cap on the vehicle, insert the key into the lock. Firmly grasp the chrome top of the fuel cap and turn the key until it stops. On right hand threaded fuel caps, turn the key counter-clockwise until it stops. On left hand threaded fuel caps, turn the key clockwise until it stops. This assures an unlocked position for the gas cap. Allow the key to return to the neutral position. 2. Remove the key and install the fuel cap on the vehicle. is00770 Figure 1. Right Hand Threaded Fuel Cap Installation NOTE When installing the fuel cap, rotate the cap one full turn past the audible click. This automatically positions gas cap to lock position. A properly locked/installed gas cap will rotate freely in both directions. Failure to do so will give an incorrect assumption that the fuel cap does not work properly. REMOVAL On right hand threaded fuel caps, insert key, and while holding the gas cap in place with hand, turn key counterclockwise until it stops, return key to original position. Gas cap must rotate 270 degrees counter-clockwise before mechanism engages to allow gas cap removal. Continue to rotate counterclockwise to fully remove gas cap. On left hand threaded fuel caps, insert key and while holding the gas cap in place with hand, turn key clockwise until it stops, return key to original position. Gas cap must rotate 270 degrees clockwise before mechanism engages to allow gas cap removal. Continue to rotate clockwise to fully remove gas cap. REPLACEMENT KEYS Record the 4 digit key number stamped on the back of the key opposite the Harley-Davidson logo, in the area provided below. If a replacement key is needed, see your Harley-Davidson Dealer with the 4 digit number to order a replacement

Incoming search terms:

HARLEY DAVIDSON FLUSH-MOUNT LED FUEL GAUGE AND GAS CAP KIT INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 29-01-2011

download
1. Remove stock gas cap from fuel tank. 2. Clean and wipe inside surface of fuel tank filler cup, O-ring seal surface, and trim ring adhesive surface with a mixture of equal parts of isopropyl alcohol and distilled water. 3. See Figure 1. Install gas cap into fuel tank. is00407 Figure 1. Screw in Gas Cap is00466 Figure 2. Note Position of Arrow on Trim Ring 4. Push down on gas cap and rotate clockwise one-eighth of a turn to lock. To unlock, push down on gas cap and rotate counterclockwise one-eighth of a turn. 5. See Figure 2. Before removing adhesive backing, note position of arrow on inside diameter of chrome trim ring. NOTE As you rotate trim ring, you will see gaps between trim ring and fuel tank. Rotate trim ring to position that best eliminates gaps between fuel tank and trim ring. Rotation of trim ring should be minimal. 6. See Figure 3. With the arrow pointing toward front of motorcycle, rotate chrome trim ring slightly to determine best position of bottom chrome trim ring to contour of the fuel tank 7. See Figure 4. Mark position of chrome trim ring with masking tape or grease pencil. 8. Carefully cut masking tape with a hobby knife making sure not to scratch chrome trim ring or paint surface on fuel tank. 9. Peel off adhesive backing from chrome trim ring. 10. Using gas cap to center and masking tape (or grease pencil mark) to align, press chrome trim ring firmly into position for about ten seconds. 11. Peel off masking tape (or remove grease pencil mark) from chrome trim ring and fuel tank. 2 1 is00414a 1. Masking tape 2. Cut masking tape Figure 4. Align Trim Ring and Press into Place NOTE Allow adhesive trim ring to cure for about 5-7 minutes before you continue with kit installation. Install Flush-Mount LED Fuel Gauge 1. Remove the seat following the instructions in the service manual. Disconnect negative (-) battery cable first. If positive (+) cable should contact ground with negative (-) cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury. (00049a) To prevent accidental vehicle start-up, which could cause death or serious injury, disconnect battery cables (negative (-) cable first) before proceeding. (00307a) 2. Disconnect battery cables, negative (-) cable first. 3. Remove stock fuel gauge. Refer to service manual for instructions. 4. Insert wires down tube of fuel tank from LED fuel gauge. 5. See Figure 5 and Figure 6. Insert LED fuel gauge in the fuel tank cup

Incoming search terms:

Incoming search terms: