vance and hines part 330 p

You search Auto repair manual PDF vance and hines part 330 p, if there are search results will appear below. If search results do not exist, please search by others keyword.





VANCE And HINES MOTORSPORTS SUPERCHARGER Installation Manual

0

Filed Under (Tips and Review) by admin on 27-10-2010

download
Installation is complete in eight hours or less and no additional engine modiÞcations are required.* Simply remove the standard air box, injector bodies, water pump and a few hoses. The supercharger and plenum chamber Þt into the same location, with the drive belt and cover attaching to existing bolt holes in place of the original water pump housing. The only change to the engine is the removal of the water pump housing and drive shaft. A longer shaft and strengthened housing are supplied, which provide the output shaft for the Supercharger drive belt. The complete kit includes; What you get is an instant 35-40% increase in Power and Torque. The Þnished installation is deceptively simple; a clean looking, reliable motorcycle with unrivaled grunt, power and enhanced engine sound. When compared to a Turbo application, the Supercharger provides far greater volumetric efÞciency with no turbo lag or heat build-up. This kit provides smooth Òalways onÓ power for both Street and Strip use. The Supercharged V-Rod pulls cleanly from idle, and top gear roll-ons are impressive at any speed. Order yours today and put a smile on your face every time you ride

Incoming search terms:

Harley Davidson Touring/ Dresser Slip-on Exhaust System REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Remove both left and right saddlebags and set them aside. 2. Loosen the bolt from the pinch clamp on the front end of each muffler. Note: On the older model Dresser, spread the clamps just enough to remove them. 3. Remove the two 5/16″ bolts that mount the muffler to the saddlebag supports. Repeat this step on the opposite muffler. 4. Remove the stock mufflers and set them aside. Note: It may be necessary to use a penetrating lubricant to loosen the muffler from the head pipe. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Install one muffler clamp (supplied) over the front (notched end) of each muffler. 2. Slip the muffler over the stock head pipe, mount the muffler to the saddlebag support using the two stock 5/16″ bolts and tighten. Note : There is a different muffler for the left and right side of the motorcycle. The dent in each canister should always be facing in. This is to allow clearance for the swingarm. 3. Tighten the two muffler clamps. (Torque Specification 12 ft/lbs.) 4. Replace the saddlebags. 5. Be sure to tighten all hardware before starting your motorcycle. RE-JETTING INSTRUCTIONS Re-jetting the carburetor will result in realizing the “full” potential of this performance exhaust system. Vance & Hines offers jet kits for most applications. For fuel injected models, we recommend the use of Vance & Hines Fuelpak part number 61003. PLEASE NOTE: Every effort is made for Vance & Hines Exhaust Systems to provide improved cornering clearance. However, due to design and space limitations on some motorcycle models, ground and cornering clearance may not be improved and in some cases may be reduced. Be sure to follow proper installation instructions

Incoming search terms:

HARLEY DAVIDSON SOFTAIL SPRINGER Dual Slip-On Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 22-12-2010

download
REMOVING THE STOCK MUFFLERS 1. Loosen the bolt on the pinch clamp at the front end of each muffler. 2. Remove the two bolts that mount the muffler to the mounting bar. Repeat this step on the opposite muffler. 3. Remove the stock mufflers and set them aside. Note: It may be necessary to use a penetrating lubricant to loosen the mufflers from the head pipes. INSTALLING YOUR NEW VANCE & HINES SLIP-ON EXHAUST SYSTEM 1. Remove the two 5/16″ flanged head bolts from the bracket that is welded to the backside of each muffler. Attach one of the mounting brackets (supplied) to each muffler, using two of the 5/16″ flanged head bolts (removed earlier), leaving them loose at this time. When the bracket is mounted correctly on the muffler, the single hole end should point down when the muffler is mounted to the bike. 2. Be sure there is a muffler clamp (supplied) over the front (notched end) of each muffler. 3. Slip the muffler onto the stock head pipe, mount the muffler to the rear most hole of the stock mounting bar, using one of the stock bolts and tighten. Repeat this step on the opposite muffler. Note: When installed correctly, the Vance & Hines logo on the muffler should face outwards. 4. Tighten the two muffler clamps. 5. Tighten the two 5/16″ flange bolts on each muffler bracket. 6. Wipe any finger prints or oil off any chrome parts of the exhaust system before starting the motorcycle. 7. Be sure to tighten all hardware before starting your motorcycle. RE-JETTING INSTRUCTIONS Re-jetting the carburetor will result in realizing the “full” potential of this performance exhaust system. Vance & Hines offers jet kits for most applications

Incoming search terms:

HONDA SHADOW ACE TOURER EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the pinch clamp bolt on the left hand muffler crossover pipe. (Located on the right of the motorcycle, where both mufflers merge with the head pipes). 2. Remove the two 8mm bolts that mount the left hand muffler to the frame. Drop the muffler down to clear the mounts and pull out from the collector. 3. Remove the right hand frame cover to avoid damaging it. 4. Remove the 8mm nut holding the head pipe flanges to the cylinder heads. Remove the 8mm bolts that mount the right hand muffler to the frame. 5. Remove the remainder of the exhaust system from the motorcycle and set it aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Be sure to check that the stock exhaust gaskets are in good shape. If you have any doubts as to their condition, replace them. 2. Install the chrome exhaust flanges (supplied) over the front and rear head pipes. 3. Install the rear head pipe to the rear cylinder using the stock 8mm acorn nuts. Route the pipe approximately 3/4″ beneath the swingarm, leaving the nuts finger tight at this time. 4. Install the front head pipe to the cylinder head using the stock 8mm acorn nuts. Its routing follows the stock head pipe, leave the nuts finger tight at this time. 5. Your Vance & Hines mufflers use the stock mounting locations and rubber grommets. Remove the steel spacers and rubber grommets from your stock mufflers and install them into Vance & Hines mufflers in the same locations. 6. Slip a chrome muffler clamp onto the inlet end of each muffler. Install the clamp hardware as shown in figure 1 (hardware supplied). Leave them loose at this time. 7 Slide the left hand muffler assembly (stamped H641) onto the rear head pipe approximately two inches. Mount the mufflers to the motorcycle using the stock bolts, in the stock locations. 8. Repeat the above step with the right hand muffler (stamped H640). 9. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edges of the heat shields with the location of the mounting clips that are welded to the back side of the heat shield. Position the right rear heat shield (stamped H226) over the rear head pipe and feed the tail end of the hose clamps into the clips. Be sure that each clamp is engaged into both clips. Repeat this procedure with each heat shield.

Incoming search terms:

Harley-Davidson Sportster 883/ 1200 Straightshot HS Exhaust system REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Loosen the heat shield clamps on both the front and rear exhaust pipes. This allows easier access to the head pipe mounting nuts. 2. Remove the two head pipe mounting nuts from each flange, located at the cylinder head. 3. Remove the two bolts from each muffler body which attach the muffler bodies to the mounting bar. 4. Remove the clamp bolt which mounts the rear head Page 1 of 4 D445N Rev. 1.0 Sportster 883/1200 Straightshot HS Exhaust system Part #17815 U S A Congratulations, you have purchased the finest exhaust system available for your motorcycle. Your VANCE & HINES exhaust system is designed and crafted for maximum performance, a perfect fit, a great sound and unbeatable style! Please follow the installation instructions below and if you have any questions, feel free to call our technical help line (562) 926-5291. Attention Installer: (if other than owner): Please forward this instruction sheet to the purchaser of this product. These instructions contain valuable information necessary to the end user. Tools required for installation: 3/16″ & 5/16″ Allen wrenches 3/16″ & 5/16″ Allen & 1/2″ sockets 3/8″ Ratchet & Extensions T30 Torx driver 1/2″ Wrench 5/16″ nutdriver/flat blade screwdriver Ft/lb. & In/lb. Torque wrenches Snapring pliers pipe to the belt drive cover bracket and carefully remove both exhaust pipes from the motorcycle. 5. Remove the drive belt cover and take the bracket off the rear cover bolt, it will not be re-used. 6. Loosen the brake rod at the rear eyelet using a T30 Torx driver. 7. Remove the exhaust mounting bar, saving the three mount bolts and washers for re-use. 8. Using snapring pliers, carefully remove the flanges and circlips from the stock exhaust system. Save for re-use. NOTE: If circlips look bent or twisted replace them with new circlips. VANCE & HINES EXHAUST SYSTEM INSTALLATION 1. Check condition of stock exhaust gaskets. Replace if damaged or worn. Vance & Hines recommends you replace your gaskets with Screamin’ Eagle gaskets part number 17048-98. 2. Install and tighten supplied mounting bracket (stamped 356-P) using stock bolts and washers (Figure 1). Torque to 30-33 Ft/Lbs. NOTE: Support the rear of the bracket during tightening to insure it is aligned with the bottom edge of the frame. 3. Re-install drive belt cover. Torque to 1 x 3/8″ bolt 30-33 Ft/Lbs. 2 x 1/4″ bolts 80-120 In/Lbs. 4. Re-install brake rod eyelet using blue thread locking compound (Loctite® 243). There is a 1/2″ clearance hole in the bracket to allow access for tightening brake rod eyelet. Torque to 120/180 In/Lbs. (Figure 1). 5. Remove header pipes and heat shields from protective packaging. Place each heat shield on a non-abrasive surface such as a blanket or carpet. Using a felt tip pen, mark outside edge of each heat shield to show location of mounting clips where hose clamps will loop through (Figure 2). 6. Install circlips and flanges from the stock system onto both new head pipes.

Incoming search terms:

Harley Davidson Sportster Straightshots HS Slip-on Exhaust system

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Loosen the heat shield clamps on both the front and rear exhaust pipes. This allows easier access to the head pipe mounting nuts. 2. Loosen, but do not remove, the two head pipe mounting nuts from each flange located at the cylinder head. 3. Remove the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. 4. Loosen the clamp holding the mufflers onto the head pipes. Page 1 of 4 D480IN Rev. 1.0 Sportster Straightshots HS Slip-on Exhaust system Part #16819 U S A Congratulations, you have purchased the finest exhaust system available for your motorcycle. Your VANCE & HINES exhaust system is designed and crafted for maximum performance, a perfect fit, a great sound and unbeatable style! Please follow the installation instructions below and if you have any questions, feel free to call our technical help line (562) 926-5291. Attention Installer: (if other than owner): Please forward this instruction sheet to the purchaser of this product. These instructions contain valuable information necessary to the end user. Tools required for installation: 1/2″ combination wrench 3/8″ drive ratchet and 9″ extension 9/16″ and 1/2″ sockets 5/16″ Nutdriver/flat blade screwdriver 5. Remove the two bolts from each muffler which attach the mufflers to the mounting bar. 6. Remove the mufflers by sliding them off the head pipes. 7. Remove the clamp from the nose of each muffler (these will be re-used when installing the new mufflers). 8. Remove the gaskets from the crossover ports on the stock mufflers. Inspect the gaskets and replace if damaged or worn (H-D part #65927-00). 9. Install crossover gaskets onto mounting bar on motorcycle. VANCE & HINES EXHAUST SYSTEM INSTALLATION 1. Remove mufflers and heat shields from protective packaging. 2. Slide the nut plate inside the bracket that is welded to the backside of each muffler body and attach the muffler bodies to the mounting brackets (stamped 379-P) using four 5/16″ x 5/8″ flange head bolts (supplied). Leave them loose at this time (Figure 1). 3. Slide stock exhaust clamp onto nose of each muffler. 4. Slide mufflers onto head pipes and align crossover port with gasket on mounting bar (Figure 2). Press into place on gasket. 5. Attach the muffler brackets to the stock mounting bar using four 5/16″ x 3/4″ hex head bolts, washers, and nuts (supplied). Leave them loose at this time (Figure 3). 6. Tighten cylinder port exhaust flange nuts on front and rear cylinders. 7. Install and tighten the clamp bolt which mounts the rear head pipe to the belt drive cover bracket. 8. Align muffler and bracket so they sit level. Tighten the muffler mounting bolts and the bracket mounting bolts. 9. Tighten the clamp holding the muffler onto the head pipe.

Incoming search terms:

Harley-Davidson DYNA Straightshot Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 22-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the heat shield clamps on both front and rear exhaust pipes. 2. Remove the two mounting nuts from each head pipe, located at the cylinder head. 3. Remove both front and rear head pipe clamp bolts. 4. Remove the entire exhaust system and set it aside. 5. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. Note: If circlips look bent or twisted replace them with new circlips. 6. Remove the rear head pipe clamp bracket from the transmission cover. Remove any studs and bolts necessary and set aside to use when installing the new muffler mounting bar to the transmission housing. Refer to figure 1. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Install the mounting bar (supplied) to the transmission housing using the stock hardware. Refer to figure 1 . Note: The mounting bracket should mount flatagainst the transmission housing. Some motorcycles use a stud to mount the stock rear head pipe clamp, be sure to remove the stud from the transmission housing and replace it when mounting the bracket, this will insure that the bracket is flat against the housing. 2. Check condition of stock exhaust gaskets. Replace if worn. Vance & Hines recommends you replace your gaskets with Screamin’ Eagle gaskets, part number 17048-98. 3. Install the circlips and flanges from the stock system onto both new head pipes. 4. Slide one pipe clamp (supplied) onto the front head pipe. Position the clamp in the approximate location on the tube where it mounts to the engine. 5. Slide one pipe clamp (supplied) onto the rear head pipe. Position the clamp in the approximate location on the tube where it mounts to the top hole in the mounting bar bracket. Refer to figure 1. 6. Unscrew all of the hose clamps (supplied) until they are completely loose. Feed the tail end of the hose clamp into the clips on the inside of both heat shields. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike

Harley davidson Sportster Custom Straightshot Exhaust System REMOVAL AND INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 19-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the heat shield clamps on both front and rear exhaust pipes. 2. Remove the two mounting nuts from each head pipe, located at the cylinder head. 3. Remove the nut that mounts the front muffler to the engine, located below the rear brake master cylinder. 4. Remove the bolt that mounts the rear muffler to the mounting bar. 5. Remove the entire exhaust system and set it aside. 6. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. Note: If circlips look bent or twisted replace them with new circlips . INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Vance and Hines recommends you replace your exhaust gaskets with Sceamin’ Eagle gaskets part number 17048-98. 2. Install the circlips and flanges from the stock system on to both of the new head pipes. 3. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edge of both heat shields with the location of the mounting clips that are welded to the backside. Position the front heat shield over the head pipe and feed the tail end of the hose clamps into the clips. Be sure that each hose clamp is engaged with both clips. Repeat this step with the rear heat shield. Note: The screw end of the hose clamp should be accessible, but not visible when pipe is mounted on the bike. 4. Install the front head pipe using the stock nuts, do not tighten at this time. 5. Install the rear head pipe using the stock nuts, do not tighten at this time. 6. Install one muffler clamp (supplied) over the inlet (notched end) of each muffler. 7. Identify the front and rear muffler mounting brackets. The front bracket is stamped with the number 305 and the rear muffler bracket is stamped 213 . 8. Install the front muffler mounting bracket to the stud on the engine (where the stock muffler mounted) and fasten using the stock nut (leave loose at this time). The bracket will bend inward towards the center of the motorcycle when installed correctly. Note: You may need to move the wires and hoses on the lower frame rail to decrease the possibility of them chaffing on the bracket bolts. 9. Slip one of the mufflers onto the front head pipe. Slide one dog bone shaped nut plate (supplied) under the bracket that is welded to the backside of the muffler. Attach the muffler to the mounting bracket using the 5/16″ flange head bolts (supplied) leave them loose at this time. 10. Attach the rear mounting bracket to the rear muffler. Slide one dog bone shaped nut plate (supplied) under the bracket that is welded to the backside of the muffler. Attach the bracket to the muffler using two of the 5/16″ flange head bolts (supplied), leave them loose at this time. Note: The single hole in the bracket will point downward and slightly forward when installed correctly

Incoming search terms:

Harley Davidson V-ROD Powershots Exhaust System Installation Manual

0

Filed Under (Harley Davidson) by admin on 22-12-2010

download
STOCK EXHAUST SYSTEM REMOVAL 1. Loosen nose slip clamp at front of muffler section using 12mm socket. 2. Remove pin located on mounting bracket from stock exhaust system using 13mm wrench and 4mm Allen wrench. 3. Remove two 6mm Allen bolts connecting lower muffler to mounting bracket. 4. Remove the entire muffler section from the headers as a single unit. Note: Do not remove stock mount bracket, rubber mount rail or head pipes from motorcycle, since they will be re-used. 5. Loosen the exhaust port flange bolts at both cylinders without removing. This will aid in the assembly and alignment of the new system 6. Remove the OEM nose slip clamp from the front of the OEM muffler section. Save for re-use. VANCE & HINES EXHAUST SYSTEM INSTALLATION 1. Remove exhaust system and heat shields from protective packaging. Place exhaust on a non-abrasive surface such as a blanket or carpet. Using a nonpermanent marker or tape, mark outside edge of each heat shield to show location of mounting clips that hose clamps will loop through. 2. Install OEM nose slip clamp to front of Vance & Hines muffler section. 3. Loosely install tailpipe heat shields (part # D285HC and D286HC) to headers using four #20 hose clamps and one #56 hose clamp. Note position and direction of clamp heads. (Figure 1) Note: #56 hose clamp attaches both heat shields

Yamaha 2005 R1 Bike Tech Sheet

0

Filed Under (Yamaha) by admin on 18-01-2012

download
Engine: Type: Liquid cooled, four stroke, transverse four cylinder, DOHC, 5 valves per cylinder. Displacement: 1000cc Year: 2005 Horsepower: 180hp Clutch: PM Exhaust: Vance & Hines Race Exhaust Mufflers: Vance & Hines Frame: Type: Stock Year: 2005 Swing Arm: Performance Machine Chromoly +4 Extended Shocks: Race Tech Modifications: Race Tech Tuned and Lowered. Forks: Stock lowered 2.5″ Rim: Performance Machine Contrast Cut Torque Size: 19″ X 3.0″ Finish: Contrast Cut Fender: None Tire: Dunlop Sportmax D208ZR 120/70ZR19 Brake: Dual Performance Machine 4 piston Radial Calipers Wheels Rear: Rim: Performance Machine Contrast Cut Torque Size: 18″ X 8.5″ Brake: Performance Machine 4 piston Radial Caliper Finish: Contrast Cut Tire: Dunlop Elite3 250/40/R18 Other Parts: Handlebars: Stock Foot Controls: Over Racing Seat: Stock Turn Signals F/R: Anything Extra? Mirrors: Performance Machine Torque chrome Mirrors 19″ FRONT WHEEL! Paint, Chrome, and other F/X’s: Colors: yellow/Black Type: Special Paint: AirTrix Industries The Painter: Chris Wood Powder Coating: A to Z Coatings

Incoming search terms: