vance and hines right peg relocator

You search Auto repair manual PDF vance and hines right peg relocator, if there are search results will appear below. If search results do not exist, please search by others keyword.



  vance and hines right peg relocator Direct Download speed 5282 Kb/s

  vance and hines right peg relocator Full Version speed 6162 Kb/s



1981-1983 Yamaha Virago 750 & 920 Installation Instructions

0

Filed Under (Yamaha) by admin on 11-02-2012

download
Start by loosening the rear cylinder down tube bolt located on the top of the old mufflers center collector in front of the rear tire. 2. Remove both of the front cylinder exhaust pipe head nuts and set them to the side for reuse with the MAC exhaust system. 3. Remove the right side passenger’s foot peg. Set the foot peg aside as you will need to reinstall it. 4. Remove the left side passenger’s foot peg. Set this foot peg aside as it will also need to be reinstalled. Note: When you remove this bolt the entire exhaust system will be loose and may fall. You will need to support the old exhaust at this point to keep from injuring yourself. Gently move the old exhaust system side to side to remove it from the rear cylinder down tube. Once the exhaust system is loose from the down tube remove the system from under the Virago. 5. Remove the bolt holding the rear brake pedal in place and remove the brake pedal from the motorcycle. Note: Set both the bolt and the pedal aside for reinstallation. 6. Next loosen the nut on the drivers right foot peg, 1 full turn to start with. Then remove the rear nut on the same foot peg. (Note: The bolt that this nut is on goes completely through the motorcycle. This is the center stand mounting bolt.) Now remove the front nut and set both aside for reuse with the MAC system. 7. Install the center stand stop bracket under the left passenger foot peg. Install this bracket with the 90° bend facing down and towards the rear tire. (Note: Center stand sop bracket in provided in the hardware kit and is approx. 5″ long with a 90° bend in it.) Adjust the bracket by one of the large bolts through the foot peg then through the bracket and then install it into the stock location. Put on one of the washers and a nut and snug up the nut. Lower the center stand until the center stand come in to contact with the bottom of the bracket. Tighten the nut until it will hold the bracket securely. 8. Install the rear down tube clamp onto the rear muffler and install the medium sized nut/bolt/washer onto the clamp just finger tight. 9. Install the (2) small bolts into the channel bracket on the rear muffler. Install the rear mounting bracket onto the two bolts and then install the washers and nuts onto each. Tighten the (2) nuts only slight amount so that you can slide the bracket front to rear to insure that when you install the bracket you position it properly. 10. Slide the rear pipe onto the rear down tube about ¼”to ¾” past the pre-cut slots on the rear muffler pipe. Slightly snug the clamp making sure that the position of the bolt and nut will not interfere with any moving parts. The final position of this bolt can hit the tire if it is not positioned properly. 11. Install the other large bolt into the right passenger and then through the top hole in the rear muffler mounting bracket. Insert the bolt into the stock location and install the washer and the nut. 12. Align the rear muffler and you can then tighten the nuts on the rear muffler mounting bracket, the cylinder down tube and the right side passenger foot peg.
13. Install the front muffler on the rear most mounting bolt of the drivers foot peg and put the stock nut back onto the bolt. Hand tighten the bolt only at this time. Note: Install the nut at this time is only to support the muffler and to insure that the pipe does not fall on the ground while you complete the next step. 14. Lift the front head pipe into position and start the stock nuts onto the studs. It is strongly recommended that you install new exhaust gasket at this time. Note: The new exhaust gaskets are not included in the kit but are available at your local Yamaha Dealer. After gaskets are installed hand tighten the front head pipe. 15. Remove the nut from the drivers foot peg bolt and reinstall the drivers foot peg. Note: Hand tighten only at this time. 16. Finish tightening the nuts on the front head pipes. (Install these nuts according to Yamaha’s Factory specifications.) Once the nuts are tightened on the head pipe you can then tighten the drivers foot peg nuts. 17. Reinstall the rear brake pedal and tighten the bolt that holds it on to factory specifications. 18. Check all of the bolts that you have installed of removed to insure that they are tight. 19. Start the motorcycle and check for any leaks. 20. You are finished with your new MAC Exhaust System.

Incoming search terms:

HARLEY DAVIDSON SOFTAIL Shortshot Exhaust System REMOVAL AND INSTALLATION

0

Filed Under (Harley Davidson) by admin on 17-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. On FLSTC, FLSTF, FLSTN and FXSTS loosen the right hand floor board mounting bolts to gain clearance for exhaust removal and installation. 2. Loosen the heatshield clamps on both front and rear exhaust pipes. 3. Loosen the crossover pipe clamp, located between the front and rear head pipe. (This step is not necessary on 2000 models). 4. Remove the two mounting nuts from each head pipe, located at the cylinder head. 5. Remove the bolts that attach the mufflers to the frame. 6. Remove the entire exhaust system and set it aside. 7. On pre 2000 models remove the lower mounting bar. 8. FLSTN, FLSTF and FXSTD models have an upper mounting bar that must be removed in addition to the lower bar. 9. Park the motorcycle on its side stand. Remove the right side 1/4″-20 bolt which holds the lower fender in place. The fender will flex out of the way allowing the removal of the right passenger foot peg bolt. Position a floor jack under the right hand frame tube of the motorcycle below the swing arm pivot bolt. Raise the jack just enough to take the weight off the pivot bolt and remove the bolt and stock mounting bar. Set the mounting bar aside. Replace the pivot bolt and torque it between 120 -150 ft. lbs. Reinstall the passenger foot peg using the 1/2″-20 x 3″ bolt and an 1 5/8″ long spacer (supplied). 10. On 2000 year models, using a #50 Torx driver, remove the three mounting bolts, and set the mounting bar aside. (Two of the bolts are visible, the third is accessed by removing the right hand passenger foot peg.) Replace the foot peg using the 3/8″-16 x 2 1/2″ bolt and 3/4″ length spacer (supplied). 11. Carefully remove the flanges and circlips from the stock exhaust system using snapring pliers. NOTE: If circlips look bent or twisted replace them with new circlips. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Vance and Hines recommends you replace your exhaust gaskets with Sceamin’ Eagle gaskets part number 17048-98. 2. Install the mounting bracket to the frame, by aligning the two 3/8″ holes in the bracket with the two holes in the frame below the right rear footrest, using the two 3/8″-16 x 3/4″ flange head bolts (supplied), do not tighten at this time. When the bracket is mounting correctly, it should bend out and away from the motorcycle, with the four holes of the bracket toward the front of the motorcycle. 3. Install the circlips and flanges from the stock system on to both of the new head pipes

Incoming search terms:

HARLEY DAVIDSON BILLET SHIFTER PEG INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 19-04-2011

download
Kit Contents See Figure 1 and Table 1. INSTALLATION 1. Remove and discard the original equipment shifter peg. If needed, use a heat gun to apply heat to the shift lever and shifter peg threads to aid in peg removal. 2. See Figure 1. Insert the screw through the peg into the shift lever. Tighten the screw to 11-15 ft-lbs (15-20 Nm) . -J04379 1 of 2 SERVICE PARTS 1 2 B C 1 2 3 1 2 3 A is05070 Figure 1. Service Parts: Billet Shifter Peg Kits Table 1. Service Parts Table Part Number Description (Quantity) Item A – Kit 49256-99 3396 Screw, 5/16-24 x 2.25 socket head cap, lockpatch 1 Not Sold Separately Shifter peg 2 11306 Rubber (4) 3 B – Kit 49254-99 3396 Screw, 5/16-24 x 2.25 socket head cap, lockpatch 1 Not Sold Separately Shifter peg 2 11306 Rubber (4) 3 C – Kit 49238-98 3396 Screw, 5/16-24 x 2.25 socket head cap, lockpatch 1 Not Sold Separately Shifter peg 2

Incoming search terms:

2" PEG EXTENSIONS INSTALLATION INSTRUCTIONS

0

Filed Under (Tips and Review) by admin on 23-12-2010

download
* Remove the foot peg from the folding clevis base by loosening the allen bolt at the end of the foot peg, then remove the allen bolt from the peg. * Place the new longer allen bolt thru the peg and slide the smaller, male end of the peg extension onto the bolt. * Screw this assembly back into the clevis or folding part of the peg base. * Rotate the peg to the desired angle and tighten the allen bolt.

V-Star 1100 Floorboard/ Foot peg Extension Kit Installation Manual

0

Filed Under (Yamaha) by admin on 08-11-2010

download
1. Take notice of the position of the shift peg positions relative to the floorboard or foot-peg. You will be adjusting it back to these locations upon installation of the extended linkage. 2. Loosen the shifter rod jam nuts and remove the OEM shift linkage. 3. Loosen the floorboard/foot-peg assembly by removing the mounting bolts (14mm wrench) 4. Install the Extension Bracket using the OEM bolts and torque to 46 ft. lbs. Figure 1 shows how to orient the bracket relative to the front of the motorcycle. 5. Mount the floorboard/foot-peg assembly to the Extension Bracket using the SS hardware provided and torque to 46 ft. lbs. It is always a good idea to apply thread-locking compound such as lock- tite to ensure that the hardware does not vibrate loose while riding. 6. Remove the jam nuts from the OEM shift linkage and thread them gently on to the new shift linkage. 7. Install the new shift linkage by aligning the control swivel and the shifter swivel and turning the linkage. Be careful not to cross thread the linkage. The linkage will thread into both swivels simultaneously. Adjust to the desired position and tighten the jam nuts that you removed from the OEM linkage. Do not over-tighten or damage will occur to the threads. Right Side Installation: 1. Take notice of the Brake pedal position relative to the floorboard/foot-peg before removal, as it will need to be readjusted upon installation of the kit. 2. Remove the cotter pin from the brake linkage and remove the clevis pin. The brake linkage will now be separate from the brake pedal assembly. Do not discard anything. 3. Loosen the floorboard/foot-peg assembly by removing the mounting bolts (14mm wrench) 4. Install the Extension Bracket using the OEM bolts and torque to 46 ft. lbs. Figure 1 shows how to orient the bracket relative to the front of the motorcycle. 5. Mount the floorboard/foot-peg assembly to the Extension Bracket using the SS hardware provided and torque to 46 ft. lbs. It is always a good idea to apply thread-locking compound such as lock- tite to ensure that the hardware does not vibrate loose while riding. 6. Loosen the jam nut from the brake linkage and remove the linkage bracket. 7. Assemble the threaded brake linkage extension to the coupling nut and tighten using one of the provided jam nuts. Don’t forget the thread locking compound if your using it. 8. Thread the coupling onto the brake cylinder linkage and install the other end of the assembly into the brake pedal end. Tighten the jam nuts. You should be able to adjust the linkage for proper brake pedal location before tightening the jam nuts. 9. Readjust the brake light switch and your ready to roll

Incoming search terms:

SUZUKI M109 ADJUSTABLE HIGHWAY PEG MOUNTS Installation Instructions

0

Filed Under (Suzuki) by admin on 29-12-2010

download
1. Starting on the left side of the motorcycle remove the two 14mm bolts that attach the left foot peg and shifter mounting bracket to the frame. Locate the longer two of the (4) supplied mounting bolts supplied, place a lock washer first and then a washer on each. Locate the left curved main mount (it will have its polished chrome side and the circle of dowel pin holes facing outward when installed on the left side). Place the bolts thru the bolts thru the holes in the mount the slide a spacer (supplied) over each bolt. Place the mount with the bolts and spacers thru the holes of the foot peg and shifter mounting bracket removed earlier and thread the bots into the frame then tighten securely 2. Repeat this procedure on the right side using the remaining shorter bolts, lock washers, washers, mount and spacers and again tighten securely. 3. Again starting on the left side install one of the dowel pins supplied into any of the holes in the mount, place one of the remaining mounting arms (they are the same left and right) onto the dowel pin that is closest to the position you want the arm to be in. Place one of the washers onto the large allen screws then thru the finished side of the arm and thread it into the center hole of the mount. 4. Repeat this procedure on the right side. Loosely install the foot peg set you have selected onto the arms. Sit on the motorcycle to see if you are comfortable with the position you have chosen. You can adjust the position of the arms in Ω” increments forward or back as follows. Remove the arm while leaving the pin in its hole, now move the pin to the next hole forward to rotate the arm back towards the rider Ω” or into the next hole back to rotate the arm forward Ω” and re-install the arm into the corresponding hole that is in the direction you want the arm to go. 5. Adjust the angle of the foot pegs so that they are both comfortable to your feet and will fold up and to the rear when not in use. Set the peg pivot bolts tight enough to hold the in the folded position but loose enough so that you can fold them down with your foot when you need them. Recheck all fasteners for tightness.

HARLEY DAVIDSON FXD (DYNA) PASSENGER FLOOR BOARDS AND RELOCATION ARMS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 21-12-2010

download
1. Beginning on the RIGHT side, use a 9/16″ wrench to remove the bolt from the back of the passenger peg mount. Remove entire peg assembly. 2. Remove the new floorboards and mounts from their packaging. Notice the Left and Right markings on the backside of the floorboard mounting plates. 3. Install the supplied Right floorboard support (the longer one) with the round mounting face for the floorboard towards the upper-right using the supplied 7/16 x 1 º” long bolt. Apply blue Loctite to the threads. Insert the bolt from the backside where the original peg was mounted. Use a 5/8″ wrench & tighten securely. Note: If also installing with optional Relocation Arms (#FXD005-5) skip step 4 and go onto step 5. 4. Installation of Right Floorboard only. There are two sets of alignment holes on the floorboard support. Insert two of the four dowel-pins into the dowel pinholes at six and twelve o’clock. Place the right floorboard onto the mount and dowel pins so that it is parallel (horizontal) to the ground. Insert the supplied 5/16 X 1″ socket head cap screw through the floorboard mount & thread into the floorboard support. Use a º” hex key wrench & tighten securely. 5. Remove Right Floorboard – Installation of Right Floorboard with Relocation Arm. There are two sets of alignment holes on the floorboard support. Insert two of the four dowel pins into the dowel holes 180 degrees apart. Notice the L & R markings on the backside of the relocation arms. Install the Right relocation arm so marking (R) is facing inward and the threaded hole is facing toward the front of the motorcycle. There are two sets of alignment holes on the relocation arms. Place the arm onto the mount (Match dowel pin holes) in desired upper or lower position. Insert the supplied 5/16 X 1″ socket head cap screw through the relocation arm & thread into the floorboard support. Use a º” hex key wrench & tighten securely

1994 HARLEY DAVIDSON FXD (DYNA) PASSENGER FLOOR BOARDS AND RELOCATION ARMS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 01-04-2012

download
1. Beginning on the RIGHT side, use a 9/16″ wrench to remove the bolt from the back of the passenger peg mount. Remove entire peg assembly. 2. Remove the new floorboards and mounts from their packaging. Notice the Left and Right markings on the backside of the floorboard mounting plates. 3. Install the supplied Right floorboard support (the longer one) with the round mounting face for the floorboard towards the upper-right using the supplied 7/16 x 1 º” long bolt. Apply blue Loctite to the threads. Insert the bolt from the backside where the original peg was mounted. Use a 5/8″ wrench & tighten securely. Note: If also installing with optional Relocation Arms (#FXD005-5) skip step 4 and go onto step 5. 4. Installation of Right Floorboard only. There are two sets of alignment holes on the floorboard support. Insert two of the four dowel-pins into the dowel pinholes at six and twelve o’clock. Place the right floorboard onto the mount and dowel pins so that it is parallel (horizontal) to the ground. Insert the supplied 5/16 X 1″ socket head cap screw through the floorboard mount & thread into the floorboard support. Use a º” hex key wrench & tighten securely. 5. Remove Right Floorboard – Installation of Right Floorboard with Relocation Arm. There are two sets of alignment holes on the floorboard support. Insert two of the four dowel pins into the dowel holes 180 degrees apart. Notice the L & R markings on the backside of the relocation arms. Install the Right relocation arm so marking (R) is facing inward and the threaded hole is facing toward the front of the motorcycle. There are two sets of alignment holes on the relocation arms. Place the arm onto the mount (Match dowel pin holes) in desired upper or lower position. Insert the supplied 5/16 X 1″ socket head cap screw through the relocation arm & thread into the floorboard support. Use a º” hex key wrench & tighten securely. 6. At the other end of the relocation arm there are two sets of alignment holes. Insert two of the supplied dowel pins into the set of dowel pin holes 180 degrees apart that will allow the floorboard to be horizontal or parallel to the ground. Insert the supplied 5/16 X 3/4″ socket head cap screw through the floorboard mount & thread into the link arm. Use a º” hex key wrench & tighten securely.

Incoming search terms:

HONDA SHADOW ACE TOURER EXHAUST SYSTEM INSTALLATION MANUAL

0

Filed Under (Honda) by admin on 20-12-2010

download
REMOVING THE STOCK EXHAUST SYSTEM 1. Loosen the pinch clamp bolt on the left hand muffler crossover pipe. (Located on the right of the motorcycle, where both mufflers merge with the head pipes). 2. Remove the two 8mm bolts that mount the left hand muffler to the frame. Drop the muffler down to clear the mounts and pull out from the collector. 3. Remove the right hand frame cover to avoid damaging it. 4. Remove the 8mm nut holding the head pipe flanges to the cylinder heads. Remove the 8mm bolts that mount the right hand muffler to the frame. 5. Remove the remainder of the exhaust system from the motorcycle and set it aside. INSTALLING YOUR NEW VANCE & HINES EXHAUST SYSTEM 1. Be sure to check that the stock exhaust gaskets are in good shape. If you have any doubts as to their condition, replace them. 2. Install the chrome exhaust flanges (supplied) over the front and rear head pipes. 3. Install the rear head pipe to the rear cylinder using the stock 8mm acorn nuts. Route the pipe approximately 3/4″ beneath the swingarm, leaving the nuts finger tight at this time. 4. Install the front head pipe to the cylinder head using the stock 8mm acorn nuts. Its routing follows the stock head pipe, leave the nuts finger tight at this time. 5. Your Vance & Hines mufflers use the stock mounting locations and rubber grommets. Remove the steel spacers and rubber grommets from your stock mufflers and install them into Vance & Hines mufflers in the same locations. 6. Slip a chrome muffler clamp onto the inlet end of each muffler. Install the clamp hardware as shown in figure 1 (hardware supplied). Leave them loose at this time. 7 Slide the left hand muffler assembly (stamped H641) onto the rear head pipe approximately two inches. Mount the mufflers to the motorcycle using the stock bolts, in the stock locations. 8. Repeat the above step with the right hand muffler (stamped H640). 9. Unscrew all of the hose clamps (supplied) until they are completely loose. Mark the top edges of the heat shields with the location of the mounting clips that are welded to the back side of the heat shield. Position the right rear heat shield (stamped H226) over the rear head pipe and feed the tail end of the hose clamps into the clips. Be sure that each clamp is engaged into both clips. Repeat this procedure with each heat shield.

DRIVER PEGS HONDA ADAPTOR INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 29-01-2011

download
1. Assemble the peg onto the peg adaptor by removing the allen bolt from the end of the foot peg you are using. Remove the clevis assembly (folding mechanism) from the peg itself. Assemble the peg and allen bolt on to the peg adaptors. 2. The original peg pivots or folds up on a pin and has a return spring. Note how the spring is assembled into the peg. Remove the cotter pin, washer and pivot pin and foot peg. Install the new peg and adaptor assembly onto the motorcycle in the same manner and using the same spring, pin, washer and cotter pin. Set the angle of the new peg as desired and tighten the allen bolt securely. 3. Use the small set screws located at the end of the adaptors to raise and lower the foot pegs resting position.

Incoming search terms: