vespa gtv 300 windshield braces

You search Auto repair manual PDF vespa gtv 300 windshield braces, if there are search results will appear below. If search results do not exist, please search by others keyword.



  vespa gtv 300 windshield braces Direct Download speed 5282 Kb/s

  vespa gtv 300 windshield braces Full Version speed 6162 Kb/s



DETACHABLE KING SIZE WINDSHIELD FOR SOFTAIL MODELS WITH CHROME HEADLAMP NACELLE OR STREET STALKER HEADLAMP NACELLE (WITHOUT PASSING LAMPS)

0

Filed Under (Harley Davidson) by admin on 07-03-2011

download
Installation 1. Remove upper screws that attach the chrome headlamp nacelle to the front forks. 2. See Service Parts illustration. Attach the upper docking bushings (22) using washer (21) and mushroom head screws (20) Use Loctite 242 (blue) on screw threads. Torque screws to 19 ft-lbs (25.8 Nm). 3. Remove lower screws that attach the chrome headlamp nacelle to the front forks. 4a. For vehicles equipped with the Chrome Headlamp Nacelle, attach the lower docking bushing (22) using washer (21) and button head screw (23). 4b. For vehicles equipped with the Street Stalker Headlamp Nacelle, attach the lower docking bushing (22) using washer (21) and button head screw (24). Installing/Removing Windshield 1. Carefully lock bottom windshield assembly jaws into grooves of the lower rubber docking bushings. 2. Hook the top windshield assembly jaws into grooves of the upper rubber docking bushings. 3. Firmly press the windshield into place until seated on docking bushings. 4. To remove windshield, grab windshield edges on each side of center brace and firmly pull windshield loose from docking bushings. 1 WARNING Carefully inspect windshield upon completion of installation. Be sure windshield mounting does not restrict full left or full right movement of front fork assembly. Restricted movement could affect handling, resulting in personal injury. If restriction does occur, adjust windshield as needed until proper clearance is obtained. Have experienced Harley-Davidson service personnel correct any problems before riding with this accessory installed. 1 CAUTION Check mounting hardware periodically. Never ride with loose mounts. A loose mounting causes extra stress on all other mounts, as well as the windshield itself, and could result in premature failure of either or both. 1 CAUTION Do not clean Lexan®polycarbonate in hot sun or high temperature. Powdered, abrasive or alkaline cleanser will damage the windshield. Never scrape the windshield with a razor blade or other sharp instruments because permanent damage will result. Sunlight reflections off of the inside curvature of a windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections. Harley-Davidson windshields are made of Lexan®. Lexan®is a more durable and distortion-resistant material than other types of motorcycle windshield material, but still requires attention and care to maintain. • Do not use liquid windshield “protectors” on your windshield. Although they may work well on automobile safety glass, Harley-Davidson cannot ensure the results when used on Lexan®Harley- Davidson windshields. If you want to use a windshield protectant on your windshield, try Harley Glaze Polish and Sealant®. • Do not use benzine, paint thinner, gasoline, or other types of harsh cleaning agents on windshield. They will damage the windshield surface. • Do not use benzine, paint thinner, gasoline, lubricants (including Armorall), or other cleaning agents on the rubber bushings. They will damage the bushing surfaces

Incoming search terms:

HARLEY DAVIDSON FLST REPLACEMENT WINDSHIELD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION 1. See Figure 1. Remove stock windshield. 2. Remove all hardware that secures mounting brackets to windshield. The nine screws must be removed with a T- 27 TORX® screwdriver. Save all hardware and brackets for installing new windshield. 3. Remove all old tape from brackets and apply new tape (1, 2) from kit onto brackets. Align holes in tape with holes in brackets. Do not exceed recommended torque when installing mounting screws. Damage to windshield can result. (00385a) 4. Install all brackets. Tighten all screws and acorn nuts to 48-60 in-lbs (5.4 to 6.8 Nm) . 5. Install windshield (3) on motorcycle CARE AND CLEANING Polycarbonate windscreens/windshields require proper attention and care to maintain. Failure to maintain polycarbonate properly can result in damage to the windscreen/windshield. (00483d) •Do not use benzene, paint thinner, gasoline or any other type of harsh cleaner on the windscreen/windshield. Doing so will damage the surface. •Do not clean Lexan® polycarbonate in hot sun or high temperature. •Powdered, abrasive or alkaline cleanser will damage the windscreen/windshield. •Never scrape the windshield with a razor blade or other sharp instruments, as permanent damage will result. •Sunlight reflections off of the inside curvature of a windscreen/windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windscreen/windshield to avoid reflections. •Do not use benzene, paint thinner, gasoline or any other cleaning agents on the rubber bushings. Doing so will damage the bushing surfaces. Do not use harsh chemicals including rain sheeting products on Harley-Davidson windshields. They can cause dulling or hazing. If you want to use a windshield protectant on your windshield, try Harley Glaze Polish and Sealant (00231a) NOTES Covering the windshield with a clean, wet cloth for about 15 minutes before washing will make dried bug removal easier. Harley-Davidson Windshield Water Repellent Treatment Part Number 99841-01 is approved for use on Harley-Davidson Lexan windshields

Incoming search terms:

HARLEY DAVIDSON QUICK RELEASE DETACHABLE WINDSHIELD KIT INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
Installation The rider’s safety depends upon the correct installation of this kit. If the procedure is not within your capabilities or you do not have the correct tools, have a Harley-Davidson dealer perform the installation. Improper installation of this kit could result in death or serious injury. (00308a) NOTE Cover the front fender, headlamp and the front of the fuel tank with clean shop towels to prevent scratching. Make sure the windshield assembly does not contact chrome or painted parts. Damage to the finish could result. Turn Signal Relocation Relocate the turn signals according to instructions included in the Turn Signal Relocation Kit, item 20. Assemble the Clamps to the Windshield 1. See Figure 1. Remove the windshield sub-assembly from the packaging and place face down on a clean, soft surface with the mount brackets facing upward. 2. See the Service Parts illustration. Remove both the clamp and hardware kits from the packaging, and separate similar parts in preparation for assembly. Note that upper and lower clamps are exactly alike. 3. See Figure 2. Assemble the clamp assemblies and hardware stacks. The cupped side of the Belleville (cone) washers must face each other and sandwich the windshield mount brackets at each mount point. Failure to orient washers correctly can reduce the windshield’s ability to break away in a collision, which could result in death or serious injury. 4. See Figure 2. One clamp at a time, with the clamp facing upward and inboard of the windshield bracket (2), tighten the shoulder bolts (1) enough to hold the clamp orientation to the windshield during mounting of the windshield to the bike. The bolts will be fully tightened later. Install the Windshield NOTE Keep front wheel straight to prevent brackets from scratching fuel tank. 1. Make sure all four clamps are in the “open” position, then bring the windshield (with the clamp side away from you) to the front of the bike. 1 WARNING 1 WARNING ® Kit Numbers 58779-05, 57160-05 1 of 3 Figure 1. Windshield Mounting Brackets i07503 Figure 2. Windshield MountingClamp i07504 1 Shoulder bolt 2 Right windshield bracket 3 Cup washer 4 Belleville washers (cupped sides face each other with windshield bracket between)

Incoming search terms:

HARLEY DAVIDSON FLHR/ FLHP WINDSHIELD KITS INSTALLATION INSTRUCTIONS

0

Filed Under (Harley Davidson) by admin on 09-02-2011

download
INSTALLATION 1. Remove stock windshield. 2. Remove all hardware that secures the mounting brackets to the windshield. The nine screws that must be removed require a T-27 TORX® screwdriver. Save all hardware and brackets for installing the new windshield. 3. Remove all old tape from the brackets. Apply tape from kit to areas of the new windshield that had tape on the stock windshield. Do not exceed recommended torque when installing mounting screws. Damage to windshield can result. (00385a) 4. Install all brackets and tighten all screws and acorn nuts to 23-27 in-lbs (2.6-3.0 Nm) . 5. Install windshield on motorcycle. Improper installation of accessories or loading of cargo can affect motorcycle stability and handling, which could result in death or serious injury. (00455b) Failure to provide adequate clearance between stationary and moving parts can cause loss of control, which could result in death or serious injury. (00378a) NOTE Inspect windshield upon completion of installation. Be sure windshield mounting does not restrict full left or full right movement of front fork assembly. If restriction does occur, adjust windshield as needed until proper clearance is obtained. Have experienced Harley-Davidson service personnel correct any problems before riding with this accessory installed. NOTE Check mounting hardware periodically. Never ride with loose mounts. A loose mounting causes extra stress on all other mounts, as well as the windshield itself, and could result in premature failure of components. CARE AND CLEANING NOTE Sunlight reflections off of the inside curvature of a windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections

HARLEY DAVIDSON WINDSHIELD KIT REMOVAL AND INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 24-02-2011

download
REMOVAL 1. Remove all hardware securing windshield. 2. Remove windshield. INSTALLATION 1. See Figure 1. Remove rubber trim strip from the original windshield and install on the replacement windshield. 2. Put the windshield into position. At each wellnut location use a scribe, or similar pointed tool, to make a pilot hole through the windshield tape where the mounting screw (4) goes into the wellnut (3). Install the mounting screws (4), with the nylon washers (5) and on 2004 models, the rubber washers (6) positioned as shown into the wellnuts (3). 3. Tighten mounting screws from the center to the outside edge on both sides. Tighten screws to 6-13 in-lbs (0.7- 1.5 Nm) . Well-nuts will expand to grip fairing CARE AND CLEANING NOTE Sunlight reflections off of the inside curvature of a windshield can, at certain times of the day, cause extreme heat build-up on motorcycle instruments. Exercise care in parking. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections. Harley-Davidson windshields are made of Lexan. Lexan is a more durable and distortion-resistant material than other types of motorcycle windshield material, but still requires attention and care to maintain. Failure to maintain Lexan properly can result in damage to the windshield. (00230a) Do not use harsh chemicals including rain sheeting products on Harley-Davidson windshields. They can cause dulling or hazing. If you want to use a windshield protectant on your windshield, try Harley Glaze Polish and Sealant (00231a)

HARLEY DAVIDSON MULTI-POCKET WINDSHIELD BAG INSTALLATION MANUAL

0

Filed Under (Harley Davidson) by admin on 12-02-2011

download
Installation 1. Remove the acorn nuts from the inside-center, left and right on the horizontal windshield bracket. 2. Apply protective tape strips to the horizontal windshield bracket to protect chrome finish. 2. Place windshield bag and bracket with eyelets over screws in the horizontal windshield bracket. Mark the location of the vertical supports for correct placement of the rubber bumpers to protect the bottom of the bag bracket. Place two bumpers each at the marked locations of the vertical windshield supports. 3. Align the metal brace with the eyelets, to fit snugly onto the windshield horizontal bracket screws. 4. Fasten the acorn nuts removed in step 1 onto the screws through the eyelets under the windshield bag. Torque the nut to 90-110 in-lbs (10.2-12.4 Nm). NOTE The brace under the bottom of the windshield bag conforms to the contour of the windshield bracket as the acorn nuts are torqued. To keep this surface in the best condition, lightly wipe with a Harley-Davidson Micro Fiber cloth, part number 94663-02, using clear water or a mild Harley-Davidson cleaner such as: • Sunwash (part number 94659-98), • Bug Remover (part number 94657-98) or • Harley Gloss (part number 94627-98).

Kawasaki Mule 610 Windshield Installation And Operations Manual

0

Filed Under (Kawasaki) by admin on 25-10-2010

download
Seizmik Hybrid Roof Frame Kit Contents: A. Windshield Mount Top Brackets and Hardware (2) B. Windshield Clamps and Hardware (2) (not shown) C. Windshield (1) (not shown) A B C D E F G H I J K L M Note: All hardware and brackets may not be shown in this view. Windshield Top Mount Hardware Includes: A. M6x22mm Socket Head Bolts (4) B. M6x12mm Socket Head Bolts (4) C. M8 Standard Flat Washers (4) D. Compression Sleve (2) E. M8x18mm Socket Head Bolt (2) F. Windshield Stay Assembly (2) G. 1.875″ Bar Clamp Half (4) H. Windshield bracket (2) I. Windshield clamp plate (2) J. Windshield clamp gasket (4) K. M6x25mm hex head bolt (4) L. M6 flat washer (8) M. M6 hex lock nut (4) Windsheild Lower Clamp Hardware (not shown) Includes: A. M6 x 40mm Zinc Coated Hex Head Bolt (2) B. M6 Standard Flat Washer (4) C. M6 Zinc Coated Nut (2) D. M6 Wide Flange Nut (2) E. 2″ Tube Clamp (2) F. 2″ Rubber Grip Strip (2) 3 Installation Instructions: Use the passenger side clamp to ensure proper positioning. The clamp should be positioned as shown. The driver’s side clamp should be even with the passenger’s side

Incoming search terms:

HONDA GL1800 WINDSHIELD VENT INSTALLATION INSTRUCTIONS

0

Filed Under (Honda) by admin on 04-03-2011

download
NOTE: CAUTION is required when drilling and cutting to prevent cracking and scratching the windshield material. A professional glass service is highly recommended for this purpose. Should you attempt to install the windshield vent on your own, follow the instructions below. Add On Inc. will not be held liable or responsible for any damage to the windshield. 1. Place bike on center stand. 2. Cut out the template provided and center on windshield approximately 2 ¾” above the tint line. Tape the template to windshield using masking tape. Use enough masking tape to cover the area to be cut out to prevent scratching. If using a power sabre saw to cut the pattern out, put masking tape on the foot to prevent scratching the windshield. Drill the four corners using a sharp power sabre saw, electric drill (using a 7/16″ drill bit), and or hack saw. 3. Smooth cut edges with sand paper. 3. Install the vent. The two pieces will snap together in the windshield. Use chrome screws provided to secure vent in the windshield.

BMW Airhead Side Braces Installation Instructions

0

Filed Under (BMW) by admin on 26-10-2010

download
Figure B shows the upper end of the Airhead Side Brace where it attaches to the frame ( NOTE: Leave at least 1/2″ spacing below the bottom edge of the fuel tank ). Figure C shows how the Airhead Side Brace must clear the air inlet tubing Figure D showing how the lower edge (beveled end) fits the frame at the rear of the bike. Figure E shows one of the threaded cones properly welded to the frame, and painted. . Ensure Airhead Side Braces are fully assembled (threaded cones firmly bolted into the braces at both ends). 2. Hold Airhead Side Brace in their proper position (reference Figures A-D) to mark location where front and rear threaded cones will be welded to the frame. NOTE : The lower (rear) end of the Airhead Side Brace is beveled, for reference. NOTE : Make sure that both the left and right Airhead Side Braces are positioned equally. 3. Mark the frame and remove paint in the appropriate areas using emery cloth to prepare the frame surface for welding. NOTE : Measure and mark twice, weld once! 4. Hold assembled Airhead Side Braces in their appropriate positions and tack-weld at the top and bottom. Perform this step for both the top (front) and bottom (rear) ends of the Airhead Side Braces , on both sides of the bike. 5. Using removable tape, mark each Airhead Side Brace as either “left” or “right”, to make sure they are replaced onto the appropriate side of the bike after disassembly. 6. Remove the bolts, and the Airhead Side Braces from the tack-welded, threaded cones. Complete the welding of the threaded cone to the motorcycle frame at all 4 locations. 7. Clean/remove any weld splatter, and paint to protect threaded cone and frame from corrosion (see Figure E). 8. Re-assemble Airhead Side Braces onto threaded cones maintaining original left side/right side orientation. NOTE : The lower (rear) end of the Airhead Side Brace is beveled, for reference. 9. Torque hex bolts to 7 ft/lbs

Incoming search terms:

KYMCO MAXXER 300/ 250 MONGOOSE 300/ 250 SERVICE MANUAL

0

Filed Under (Kymco) by admin on 26-10-2010

download
apply or add designated greases and lubricants to the specified lubrication points. ÑAfter reassembly, check all parts for proper tightening and operation. ÑWhen two persons work together, pay attention to the mutual working safety. ÑDisconnect the battery negative (-) terminal before operation. ÑWhen using a spanner or other tools, make sure not to damage the motorcycle surface. ÑAfter operation, check all connecting points, fasteners, and lines for proper connection and installation. ÑWhen connecting the battery, the positive (+) terminal must be connected first. ÑAfter connection, apply grease to the battery terminals. ÑTerminal caps shall be installed securely. 1 . GENERAL INFORMATION 1-6 ATV 300/250 ÑIf the fuse is burned out, find the cause and repair it. Replace it with a new one according to the specified capacity. ÑAfter operation, terminal caps shall be installed securely. ÑWhen taking out the connector, the lock on the connector shall be released before operation. ÑHold the connector body when connecting or disconnecting it. ÑDo not pull the connector wire. ÑCheck if any connector terminal is bending, protruding or loose. Confirm Capacity 1 . GENERAL INFORMATION 1-7 ATV 300/250 ÑThe connector shall be inserted completely. ÑIf the double connector has a lock, lock it at the correct position. ÑCheck if there is any loose wire

Incoming search terms:

Incoming search terms: